Bürkle DAL1-1300 Lacquering Machine (1993)

Bürkle DAL1-1300

Condition: used, Year of construction: 1990, Paint/coating application system Manufacturer: Bürkle Type: DAL 1 1300 Year of manufacture: 1990 Note: Kjdpfx Alszuzqdodjnb The technical data and descriptions are transcriptions from the original order confirmation. The data is for informational purposes only and is not binding.

Condition: new, Year of construction: 2026, For professional and precise glue supply in dowel holes and back side grooves. Knjdpfxodxz Tpo Aldob Short introduction: • Always the same and right glue amount • No afterwards cleaning of the workpieces of too much glue is necessary • Easiest and minimal cleaning (1x week) of the gluing system (through cleaning program) • Glue cost savings • Ergonomic and light glue gun compared to squeezy glue bottles • Faster and more precise working compared to squeezy glue bottles

Condition: ready for operation (used), machine/vehicle number: 5981, Working height: 870 mm Working width: 1300 mm Conveyor belt width: 1270 mm Conveyor speed: 6 - 30 m/min, continuously adjustable Clearance height: 3 mm - 80 mm 1 rubber-coated application roller, 238 mm diameter, rubber coating 5 By1 1 chrome-plated metering roller, 174 mm diameter Electrical equipment: Operating voltage 400 V, 50 Hz 3 phases Total connected load: 1.9 kW Knsdpfx Aoyah Uzoldsb Motors and switching devices in explosion-proof design Additional equipment: Individual drive for the metering roller, continuously adjustable, with oscillating metering roller squeegee Operating side: left Machine length: 1000 mm Weight: 1000 kg

Condition: used, Year of construction: 2023, functionality: fully functional, total height: 1,800 mm, input voltage: 400 V, total width: 2,830 mm, total length: 2,300 mm, overall weight: 2,500 kg, working width: 1,950 mm, operating pressure: 6 bar, Equipment: documentation/manual, Kolbus Autobox BX200 with Magazine Feeder Boxmaker for producing customized folding cartons Magazine feeder for automatic sheet infeed Fully automatic setup via touchscreen Processes corrugated board up to a maximum of 10 mm Knsdeyaa Rnepfx Aldjb Slotting knife width: 7 mm Remote service enabled DEMO machine – LIKE NEW!

Year of construction: 1998, condition: ready for operation (used), Volume flow: 13,600m³/h, pressure increase: 3100Pa, rotational speed: 1500/min, motor power: 18.5kW, weight: 790kg, with Chip Container STBB HAB S, including full documentation. Knjdpfx Aoi A Ix Hsldob

Condition: used, machine/vehicle number: 007984, Max. machining width: 1300 mm Min. machining thickness: 4 mm Working Table: Fixed pass height Kedpfxowqdbms Aldenb Vacuum feed belt: yes No. Operating units: 4 Nr

Condition: used, Year of construction: 2008, · Working area X-Y-Z: 3,660 x 1,550 x 130 mm · Travel length X-Y: 4,200 x 2,000 mm Description of the units and accessories (base) The structure of the base body is a monolithic construction made of thick-walled steel. It is stiffened by welded triangular plates across the entire machine bed, making it extremely stable. The triangular shape used for load-bearing parts, with a large base, is the secret to ensuring lasting precision and stability. The machine layout allows the user an optimal workflow despite minimal space requirements. The base body constructed in this way therefore offers the machining unit a balanced and secure base with particularly good load distribution. The mobile unit carrier in gantry design is made of a solid monoblock. It is positioned in the X direction on prismatically ground guides via recirculating ball slides. The work unit is mounted on this mobile unit carrier on prismatic, ground guides and a recirculating ball slide. Axis movement: The drive system in the Y and Z axes is provided by ground, high-precision recirculating ball screws. The X-axis is driven by a backlash-free, preloaded precision rack and pinion drive. This ensures balanced load distribution during the positioning process. This characteristic is important for ensuring balanced movement even in more complex tasks. The various axes are driven by brushless three-phase servo motors/brushless AC motors. These offer excellent positioning speeds thanks to very short ramp times. Furthermore, the measuring system is fully integrated into these motors. These properties make this type of drive completely maintenance-free. · Rapid traverse in X: 40 m/min · Rapid traverse in Y: 60 m/min · Rapid traverse in Z: 22.5 m/min Vacuum system (basic) · Vacuum pump: 100 cbm/h · Power: 2.5 kW · Max. negative pressure (connection) 0.9 bar Control / control cabinet · Office PC or industrial PC (see options) · Basic NC control: ESA-GV KVARA 6.0 · Cable remote control with the most important functions ELECTRIC/ELECTRONIC CNC CONTROL Universal is equipped with a powerful NC control. The integrated office PC gives the NC control an unparalleled level of familiarity: the software runs on Windows XP and allows quick and easy programming, which is easy to learn even for inexperienced users. The system is open and allows the connection of CD-ROM drives, audio cards, barcode readers, modems, printers, scanning systems, etc. Furthermore, the installation of all network systems, as well as all commercially available CAD programs, is possible. To reduce space, the control cabinet is located under the machine table, and the operator works at a separate terminal on casters, which can be freely positioned. XILOG PROGRAMMING SYSTEM Software features: - Import of DXF files - Import of ASCII files - User interface in the operator's native language (available for languages I - GB - F - D - E) - Linear and circular interpolation in three axes, linear in space, spiral in the selected plane - Assisted programming - Calculator for direct transfer of calculated data - Graphic and syntax aids for drilling and milling operations - Parametric programming to perform the same panel machining on different Kjdpfx Aevvi Rfeldsnb

Condition: new, Year of construction: 2026, Gannomat Concept 70 Eco Laminate – Body press with rapid traverse Technical data: Laminate body press from our showroom; Working area: width from 150 – 2,500 mm, height from 150 – 1,400 mm; depth 700 mm; Knodpfx Aoiidm Njldsb - Laminate press beam at the top with 6 elements, laminate press beams on the side with 5 elements - Laminate press beams with proven tolerance compensation for tight body joints - Counterpressure surfaces are 40 mm thick, coated, continuous support plates - The pressing force of the press beams is continuously adjusted electronically via 2 potentiometers and set via a frequency converter, therefore, the torque transmission is absolutely wear-free. - Pressing force for horizontal press beams min. 500 daN (kg) to continuously max. 2200 daN (kg) - Pressing force for vertical press beams min. 300 daN (kg) to continuously max. 2200 daN (kg) - Including option: Rapid traverse speed for quick positioning of the press beams, controlled via automatic workpiece detection with sensors in the press beams, pressing speed 5/10/25 mm/sec. and rapid traverse speed 50 mm/sec, the sensors can be switched off for pressing special parts. - Tapping mode for precise positioning of the two press beams, e.g. for low pressing forces, drawers and bodies at 45 degrees. Simple operation via 6 separate push buttons, freely adjustable preselection of pressing time with automatic opening, loading height 300 mm The machine is in our showroom and can be delivered immediately. Location: in stock at 54634 Bitburg - immediately available -

Condition: used, Year of construction: 2007, functionality: fully functional, used horizontal ZENZ block bandsaw type BN 110 S, stationary Year of manufacture: 2007; completely overhauled in 2022 Conveying technology year: 2022 Serial number: 141-8300 Equipment: • 22 kW drive motor • 7 m cutting length • 5 vertical supports • 2 log turners (+2 holders) • Log lifting preparation with frame • 4 level compensators with claws (+2 holders) • 1 log roller • 1 new pre-cutter • PLC control including cutting program • Seat mounted on armrests • Left: PLC - Right: joystick • 1 Zenz automatic sharpening machine type AHB (serial no.: S-1012) • 4 bandsaw blades 6000x100x1.1 stellite for softwood (prod. no.: AB 0) • 4 bandsaw blades 6000x100x1.1 stellite for hardwood (prod. no.: AB 0) • Water cooling with 20 l tank and nozzle o Mounted on blade guide • Log lifting system o With 3 log lifting arms o With 2 cylinders • Log lifter preparation in frame Knjdpfx Alowlfdxedjb o With control unit o Mount for pipe o Two mounts for cylinders • Hydraulic frame ejector for 820 mm • Green horizontal laser indicator Mechanisation consisting of: • Hydraulic folding frame for offloading at the saw with electrically driven roller conveyor • Electrically driven roller conveyor with hydraulic ejectors o Both roller conveyors operate simultaneously • Roller table 4 m long – slightly inclined with stop o All electric and hydraulic elements operable from the operator’s station The block bandsaw including conveyor technology is fully operational.

Condition: used, Year of construction: 2019, functionality: fully functional, machine/vehicle number: AN2018080, total length: 12,860 mm, total width: 4,806 mm, type of input current: three-phase, input voltage: 400 V, feed length X-axis: 3,000 mm, working width: 350 mm, power: 25 kW (33.99 HP), TRC 1500 – Timber Repair & Cosmetic Machine Technical Description • System Overview • Process Workflow System Overview The Wintersteiger TRC 1500 is a fully automated industrial system designed to detect, repair defects in wooden boards. It combines advanced 3D scanning, high-pressure thermoplastic injection technology to deliver consistent, high-quality repairs at production speed. Defects are repaired with thermoplastic filling material using injection and application units. No filling material is wasted thanks to the precise calculation of the filling quantity and precision injection. the edges can also be filled. Key Features • Automated 3D laser triangulation defect detection • High-pressure thermoplastic injection for durable repairs • Precision finishing unit for cosmetic perfection • Independent melt temperature zones with 8 kg tank • Closed glycol-water cooling system for controlled solidification • Ethernet-based control system with remote maintenance • Unlimited product profiles and intuitive scanner interface Product Range (Workpiece Specifications) Length 500–3000 mm Width 100–350 mm Thickness 3–30 mm Production speed upto 10 m/min – depending on number and sizes of defects Filling System – Injection & Application Units • Injection Unit: • 3-axis positioning (X/Y servo-driven, Z pneumatic) • Pressure-regulated melt feed • High-pressure injection • Application Unit: • 3-axis control • Fine finishing of repaired areas Faulty Spot Eye Scanner Kedex Dmdhepfx Aldonb • 3D laser triangulation and high-speed camera system. • Detects defects from approx. 1 mm depth • Automatic height adjustment • 2D + 3D measurement • Adjustable parameters for wood types Melting Unit • 8 kg tank • Independent temperature zones • Integrated piston pump for constant pressure Cooling Unit • Closed glycol-water circuit • Stable temperature control Control System • Ethernet-based communication with remote maintenance • Access to PLC, scanner, servo drives • Energy-efficient regenerative drive technology Scanner Software • Processes 3D light-section profiles • Calculates defect volume and coordinates • Unlimited product programs • Intuitive operator interface High-Pressure Injection Process 1. Melting of thermoplastic material 2. Pressure and temperature regulation 3. Targeted injection into defect 4. Immediate cooling 5. Minimal surface residue • Benefits: • Low material usage • Excellent adhesion • No alteration of surrounding wood structure System Architecture • Melting unit • Heated hoses • Injection head • Cooling plate • Cooling unit with supply/return flow