Center draaibank ZMM Sliven - CU 400

ZMM Sliven CU 400

Year of construction: 2024, condition: new, New mechanical and electromagnetic clutches and brakes for Bulgarian machine tools of the following types: CU400, CU500, CU502, CU580M, CU582, C11MT, C11MB, C11, C13B… We also offer a wide selection of various spare parts for the above-mentioned machine tools, most of which are available from stock, while for the rest we offer the fastest possible delivery times. Guedpfx Amev Rpn Toyeg We cordially invite you to cooperate!

Condition: ready for operation (used), An old Colchester engine lathe is available. Center height: 216mm, swing diameter over bed/cross slide/in gap: 432mm/267mm/711mm, distance between centers: 2000mm, spindle bore: 76mm, speed: 1600rpm, bed width: 343mm. Machine dimensions X/Y/Z: approx. 3200mm/1100mm/1400mm, weight: approx. 2500kg. An on-site inspection is possible. Gsdpfxey E S D Eo Amyjug

Condition: good (used), Year of construction: 1980, turning diameter over bed slide: 1,040 mm, turning diameter over top slide: 710 mm, turning length: 2,000 mm, bed width: 600 mm, Optional chuck 1200 mm 2 Axis RSF Digital read out Conical turning attachment Spindle bore 130 mm Central lubrication DBC Turning Length: 2000mm Swing over bed Ø: 1040mm Swing over cross slide Ø:710mm Swing in the gap Ø: 1780mm Gap length: 1000mm Spindle bore: 130mm Bed width: 600mm Tailstock spindle Ø: 130Ø Stroke pinole: 300mm Spindle taper: 6Mk Power: 22kW Speeds / ranges: 600Rpm Feed rate X-Axis: 4000mm/min. Feed rate Z-Axis: 4000mm/min. Length: 6000mm Width: 2100mm Height: 2100mm Gjdpfxox Tgr Tj Amysug Weight: 8300kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, Year of construction: 1973, pressure 200 t chamfer lenght 3600 mm distance between columns 2650 mm dayligth 500 mm throat 300 mm stroke 250 mm working feed 10,5 mm/sec return speed 100 mm/sec ram stroke speed 150 mm/sec table height 900 mm oil volume 500 l total power requirement 37 kW weight of the machine ca. 17800 kg dimensions of the machine ca. 3710 x 1800 x 3390 mm Equipment: - Controlled axes Y1 + Y2 - Manual X-axis with digital position display Godet I D U Ejpfx Amyeug - Set of upper and lower tools - 2x stop fingers - 2x front support arms - Hand and foot controls - Side + rear safety guard - Operating instructions

Condition: new, maximum load weight: 67,200 kg, overall weight: 85,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpts from the equipment. Full specifications available upon request. GOOSENECK * Gooseneck in SNT design to optimize load floor length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractors: 6 x 2, 6 x 4, and short 8 x 4 * Detachable steel front wall, approx. 400 mm high * 3 kW electro-hydraulic power unit for controlling hydraulic functions, except for hydraulic winches * Outer beams of the gooseneck with mounting holes for bolt-on lashing rings * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of flat lashing rings at the rear of the gooseneck (LC 10,000 daN) * 1 pair of plug-in aluminum side boards, approx. 400 mm high, anodized * 1 plug-in aluminum rear board, approx. 400 mm high, anodized * Approx. 40 mm thick hardwood flooring above gooseneck, checker plate flooring above kingpin * 3.5 inch kingpin * Gooseneck guide plate for the fifth wheel plate, approx. 500 mm wide * Round NATO socket at the front connection strip (Maeler & Kaege VG 96 917) * In addition to the electro-hydraulic unit, a truck hydraulic connection with flow regulator, including bracket for hanging supply lines (Faymonville couplers) * 2 pairs of stake pockets recessed in the gooseneck, for plug-in stakes approx. 100 x 50 mm LOAD FLOOR * Extendable load floor, approx. 11,000 mm long, with rear bevel approx. 500 mm x 10° * Pneumatic locking with conical locking bolts and reinforced locking positions; supply lines are protected inside the extendable beams and automatically adjust to the respective deck length * BPW axles and suspension, 1st axle steered, 2nd axle fixed, all other axles hydro-mechanically forced steered * 1st axle with electro-magnetic reverse lock via reverse gear and manual activation * Axle load capacity: 12,000 kg each * Air suspension with lift and lower valve * 235/75 R 17.5 3PMSF twin tires * Mechanical landing gears with 2-speed gearbox and crank. JOST Modul B – static test load = approx. 50,000 kg * Continuous and, between axles, interrupted approx. 50 mm thick hardwood floor on load deck (increases coefficient of friction) * Slotted holes for attachable and repositionable bridging elements: – at the fixed part behind the gooseneck – on the front of the load floor * 1 sliding intermediate table, approx. 500 mm wide, for the sliding tube with large cross-section, checker plate flooring, front and rear with slotted holes for attachable and repositionable bridging elements Godpfxsrgzv Ne Amyjug * 1 pair of recessed flat lashing rings in the front fixed part of the load floor (LC 10,000 daN) * 9 pairs of recessed lashing rings, foldable outward, in the load floor perimeter frame (LC 10,000 daN) * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking control, no installation required in the tractor * 1st axle with automatic lift axle function and start-up assist according to EU Regulation 2021/535 * Under the gooseneck and at the rear cross member, left and right, a 7-pin socket each with holder for warning signs * Factory-applied sand coating on the perimeter frame of the load floor as well as the checker plates and the transition area between load decks

Condition: used, Year of construction: 2010, operating hours: 11,780 h, Equipment: ABS, all wheel drive, Volvo EXCAVATOR EW140C air conditioning 16,850 kg 91 kW Top condition Gsdpfx Aeyltr Ajmyjug

Condition: good (used), Diameter over bed: 500 mm Diameter over carriage: 270 mm Diameter of swing over cross slide: 700 mm Distance between centers: 1500 mm Diameter of tailstock spindle housing: 70 mm Travel of tailstock spindle: 180 mm Travel of cross slide: 300 mm Maximum workpiece weight: 300 kg Gujdpfx Aozf Nd Hjmyeg Total power: 6.6 kVA Machine weight: 1760 kg

Condition: used, Year of construction: 1982, Technical details: faceplate diameter: 2600 mm turning diameter over support: 2500 mm Guodpfx Aewtctyomyjg turning length: - mm centre distance: 1600 mm turning diameter over bed: 2900 mm spindle bore: 100 mm revolution per minute: gear steps U/min feed range: Überdrehen 0,12-31,5 Plandrehen 0,12-45 mm/min bed guideways length: 2900 mm max. workpiece weight between centres: 400.000 kgs total power requirement: 45 kW weight of the machine ca.: alle Komponenten zusammen: ca. 29,0 t machine dimensions LxWxH: 5.2 x 5,0 x 3,1 m 3-way measuring system with digital display RSF electronics Control panel Cooling unit for Rittal electric cabinet *

Condition: good (used), Year of construction: 1995, roller (top) diameter: 330 mm, sheet thickness (max.): 23 mm, Manufacturer: IMCAR Type: SIHR Year of manufacture: 1995 Extended end for profile bending rolls (Pipe & T-Angle) Central lubrication Digital readout position side rolls Fully hydraulic machine Hydraulic drop end Hardened rolls Specifications Metric US Standard Roll width: 3100 mm Sheet thickness at 3 x top roll Ø: 18 mm Sheet thickness at 5 x top roll Ø: 23 mm Sheet thickness for initial bending: 20 mm Top roll Ø: 330 mm Side roll Ø: 310 mm Number of rolls: 3 Bending speed: 0 - 5 Side roll adjustment: 200 mm/min. Number of driven rolls: 2 Power: 15 kW Gjdpowpku Dofx Amysug Dimensions (estimated) Length: 5250 mm Width: 1700 mm Height: 1700 mm Weight: 11900 kg Please note: The information on this page has been provided to the best of our knowledge, and wherever possible, from the manufacturer. The information is given in good faith, but accuracy cannot be guaranteed. Accordingly, it does not constitute representation or contractual terms. We recommend you check all critical details.

Condition: used, Year of construction: 1987, faceplate diameter 3600 mm swing diameter 4500 mm Guodpeyz Db Usfx Amysg turning height 1850 mm turning speed range 0,6- 50 U/min weight of the machine ca. 72 t verticale turning machine double coloumn - digital scale - double coloumn - 2x ram - movable cross slide - extra toolholder (four station) on the side of facing plate