Hydraulic press

WMW-ZEULENRODA PYE 250 S 1 M

Condition: used, Year of construction: 2020, operating hours: 521 h, Internal vehicle number: VTC30048 Available immediately. More information at: Luis Lucena Viktoria Sologubova Manitou MHT 10180 heavy-duty telehandler – 18-tonne lifting capacity – 521 operating hours Dcedpsza Nq Rofx Adhon High-performance Manitou MHT 10180 heavy-duty telehandler, manufactured in 2020, with just 521 operating hours. The machine offers a maximum lifting capacity of 18,000 kg, a lifting height of 9.63 m, and is equipped with a hydraulically adjustable fork carriage and pallet forks. Technical data: * Vehicle number: VTC30048 * Vehicle condition: Used machine * Category: Telehandler * Manufacturer: Manitou * Model: MHT 10180 * Series: 129M ST4 S1 * Year of manufacture: 01/2020 * Model year: 2020 * Operating hours: 521 hours * Maximum lifting capacity: 18,000 kg * Maximum lifting height: 9.63 m * Maximum reach: 5.56 m * Unladen weight with standard forks: 24,000 kg * Technical inspection: New * CE marking: Present Engine and drive: * Engine manufacturer: Mercedes-Benz * Engine type: OM 934 LA * Emission stage: Stage IV/Tier 4 Final * Cylinders: 4 * Displacement: 5,100 cm³ * Power: 129 kW (176 hp) * Maximum torque: 750 Nm at 1,600 rpm * Transmission: Hydrostatic * Forward/reverse gears: 2/2 * Maximum travel speed: 25 km/h * Traction force under load: 15,970 daN * All-wheel drive * All-wheel steering * Automatic negative parking brake * Hydraulic service brake Hydraulic system: * Variable hydraulic pump * Hydraulic flow rate: 205 l/min * Hydraulic pressure: 350 bar * Hydraulic oil tank: 290 liters * Hydraulically adjustable fork carriage Dimensions: * Overall length with implement carriage: 6.65 m * Overall width: 2.52 m * Overall height: 3.00 m * Wheelbase: 3.75 m * Ground clearance: 0.44 m * Turning radius (outer radius): approx. 5.50 m * Tilt angle: 12° * Dump angle: 105° Capacities: * Fuel tank: 315 liters * AdBlue tank: 63 liters * Hydraulic oil: 290 liters * Engine oil: 21 liters Cab and safety: Enclosed ROPS/FOPS cab, Level 2 Safety system according to EN 15000 JSM joystick control All-wheel steering Rotating beacon Work lights Cab protection grille Large-dimensioned off-road tires Noise level at the driver's seat: 80 dB(A) External noise level: 107 dB(A) Attachment: * Manufacturer: Manitou * Type: PFF + POS + DL * Serial number: 53010702 * Year of manufacture: 2019 * Self-weight: 1,900 kg * Rated lifting capacity: 14,000 kg * Load center: 1,200 mm * Hydraulically adjustable fork carriage * Pallet forks included Inspection and functional test possible by prior arrangement. Further information, photos, load charts, and videos are available upon request. Errors, changes, and prior sale reserved.

Condition: new, Year of construction: 2025, We are a production company that is constantly developing dynamically thanks to the professionalism and commitment of our employees. Thanks to the experience we have gained, we are able to offer the best and highest quality solutions in the field of production. The folding bench ZGR - 4140 mm 0.8 mm incl. Roller shears and hand folding machine - Working length: 4140 mm - bending capacity: up to 0.8 mm (sheet steel) - Bending angle: max. 150 degrees - Folding beam thickness: 30 mm - Upper beam stroke: 80 mm - Weight: approx. 1000 kg - Lifting the top beam in three positions Furnishing: - Roller shear 0.8 + 350 Euro - Degree scale Dcsdpfx Aoch Tkvedhsn - Angle stop - rear frame to hold the sheet - hand folding machine Price: 6 550 euros Please contact us if you are interested.

Condition: good (used), functionality: fully functional, Year of construction: 2000, sheet thickness steel (max.): 16 mm, back gauge: 1,000 mm, cutting length (max.): 3,150 mm, foot switch motorized arrester behind cutting angle adjustment Technische Daten / technical details: Schnittleistung / max. cutting capacity 16 mm max. Schnittlänge / max. cutting length 3150 mm Anschlag / limit stop 1000 mm Dcedpfx Aov Syyvjdhsn Gewicht der Maschine / weight 16300 kg Technische Daten, Zubehör und Beschreibung der Maschine sind unverbindlich - Technical data, accessories and description of the machine are not binding.

Condition: new, Year of construction: 2024, feed rate X-axis: 25 m/min, feed rate Y-axis: 25 m/min, feed rate Z-axis: 25 m/min, total length: 7,600 mm, total height: 3,000 mm, total width: 2,650 mm, overall weight: 14,000 kg, spindle speed (min.): 50 rpm, spindle speed (max.): 4,000 rpm, DYAS 3 BDC CNC Beam Profile Machining Center Operating Range for Section Min. 200 x 80 mm / Max. 1200 x 500 m Operating Range for Length Min. 2000 mm / Max. 12000 mm (Gross: 12500 mm ) Drilling Head (Spindle) 3 Dcedpfx Adjgbdpkehen Spindle Speed 50-4000 (stepless) rpm Spindle Power 22 Kw Spindle Torque 280 Nm Tool Changer 6 for each spindle , total 18 Tapping Capacity M10-M30 Bandsaw (Optional) Cutting Speed 20-100 m/min / Mitering Angle +60°/-45°

Condition: used, Year of construction: 1999, pressure 180 t chamfer lenght 3100 mm distance between columns 2550 mm throat 310 mm stroke 200 mm ajustment speed 80.0 mm/sec working feed 10.0 mm/sec return speed 58.0 mm/sec dayligth 385 mm table width 240 mm work height max. 885 / 1050 mm oil volume 180 ltr. total power requirement 15.0 kW weight of the machine ca. 9850 kg. range L-W-H 4200 x 1750 x 2450 mm from a maintenance workshop well-maintained condition (!!) - in checked condition - machine video - ?v=o_t9BBMsNNs Equipment: - simple, conventional electro-hydraulic press brake * with torsion shaft for parallelism of the upper beam Dsdpoxab Erjfx Adhscn - electric back stop, with ball screws (X axis) * with 4x manually adjustable stop fingers * fine adjustment via handwheel at the front, with analog position display - electro-motor adjustment of the immersion depth (Y1 + Y2 axis) * with digital position display - swiveling operation, mounting side on the left - 1x set of upper tools - 1x rotatable MULTI V universal die block - 2x front / movable support arms - 1x freely movable 2-hand foot control - operating instructions (PDF)

Condition: used, empty load weight: 10,900 kg, maximum load weight: 43,600 kg, overall weight: 54,500 kg, axle configuration: > 3 axles, first registration: 04/2025, loading space length: 8,700 mm, loading space width: 2,550 mm, loading space height: 855 mm, tire size: 245/70 r17.5, color: grey, Year of construction: 2025, operation weight: 10,900 kg, Equipment: ABS, Gooseneck, rigid, in center tube design: -Closed outer frame with cutouts for lashing straps (LC 1,500 daN) -Steel floor with anti-slip surface -Including rail for aluminum ramps -2" – Kingpin -Mechanically operated BPW landing gear -550 mm long, 8’ bevel at the end of the gooseneck -Front bulkhead incl. parking position for rear wall, 400 mm high -Spare wheel holder mounted vertically on the front of the gooseneck -3 pairs of lashing rings LC 5,000 daN recessed in the loading platform of the gooseneck -Aluminum stake sides 400 mm high, consisting of 2 x side boards length 3,150 mm and rear board with rails (galvanized) -Storage box rectangular, aluminum, hinged lid, lockable, dimensions approx. 400 x 800 mm, center -Storage box 45’, aluminum, hinged lid, lockable, dimensions approx. 400 x 800 mm, left -Storage box 45’, aluminum, hinged lid, lockable, dimensions approx. 400 x 800 mm, right Loading platform, single telescoping: -Closed outer frame with cutouts for lashing straps (LC 1,500 daN) -Fixed section at the front 700 mm -Sheet metal floor with anti-slip surface -Beveled interface between fixed section and loading platform for attaching bridge planks and wheel recesses -Excavator recess incl. elongated holes for securing the load (LC 1,500 daN), length approx. 3,850 mm -Preparation for hydraulic ramp (electrical supply) -Supports for widening to 3,000 mm -Beveled vehicle rear 8°, 550 mm long Dcjdpfei Ai E Rox Adhsn -Sled design for easy installation and removal of ramps -Continuous mudflap at the rear -1 pair of lashing points LC 10,000 daN in the center of the loading platform behind the gooseneck -7 pairs of lashing points LC 10,000 daN in the outer frame of the loading platform -6 pairs of rail pockets 100 x 50 mm in the outer frame of the loading platform -1 pair of lashing points LC 10,000 daN in the center in the rear area of the loading platform -1 pair of rail pocket strips approx. in the center of the loading platform -1 pair of rail pocket strips on the fixed section -1 pair of rail pocket strips behind the last axle Ramps: -Hydraulic double folding ramps, 2,750+1,500x800 mm -Wood deck larch -Control via remote control (possible via cable and radio) -Ramps with quick-change (dismantling system) Chassis: -Axle manufacturer BPW ECO Max -2 ride heights -4 axles á 10 t (technically 12 t) -Twin tires 245/70 R17.5 -2 x fixed axle and 2 x friction-steered axle -Reverse steering lock of the friction-steered axle via reverse gear -Brake system manufacturer Knorr (according to EU regulations with EBS-E) -TIM G2 from Knorr (Trailer Information Module) -Vehicle stability control RSS (Roll Stability Support) -Load-dependent lift axle on the first axle incl. starting aid (forced lowering of the lift axle via TIM possible) Accessories: -4 chocks with holder -2 pairs of warning signs 423 mm x 423 mm, with 2 position lights and socket for rotating beacon, steplessly adjustable up to 3,950 mm -Mounting options on the gooseneck and on the loading platform (alternatively on the ramp, if available) are included -Plug-in partition sheet at the end of the excavator recess -Electro-hydraulic unit for ramp operation -Ramp operation via wireless remote control -Hydraulic support legs at the rear of the vehicle for support during the loading process -1 pair of additional reversing lights rear, switched on in reverse gear -Wood widening planks - larch (option)

Condition: used, Year of construction: 1995, Technical details: sheet width: 3000 mm plate thickness: 12 mm distance between columns: 3500 mm control: Cybelec DNC 10 G back gauge: 1200 motorisch mm cutting angle: 1,2 - 2,73 ° cutting gap adjustment: ja mm cutting capacity : 66.000 daN daN Knife length: 3100 mm down holder: 17 Stück interface: RS232 Table dimensions: 3200 x 600 mm total connected load: 22 kW weight of the machine ca.: 11,0 + (1,0 to Anbauteile+Zubehör) t space requirements approx. LxWxH: ca. 4,5 x 2,6 x 2,1 m transport dimensions LxWxH: ca. 5,0 x 2,25 x 2,2 m The guillotine shear was put into operation for the first time in 1998. The DNC 10 G control unit was specially designed for guillotine shears. It has a numerical axis for controlling the backgauge and automatically calculates and regulates the cutting gap, the cutting angle and the cutting depth, taking into account the material to be cut. (Data from the manufacturer) Table with side stopL:930 x W:105 x H:42 mm Dcjdevc Amtopfx Adhon 2 table extensions L:1600 x W:100 x 83 mm Angle fence (attached to table extension) Operation via control panel with swivel arm and foot control Equipment: Drain with rollers for clippings 2x protective grid *

Condition: used, functionality: fully functional, fuel type: diesel, empty load weight: 18,490 kg, lifting height: 10,000 mm, mast type: telescopic, Year of construction: 2016, operating hours: 4,614 h, total length: 6,140 mm, free lift: 1,100 mm, construction height: 2,990 mm, fork length: 2,400 mm, fork carriage width: 2,480 mm, drive type: Diesel, load capacity: 13,000 kg, construction width: 2,510 mm, Rigid telescopic forklift Load center of gravity: 600 Fork width: 200 mm Dcjdpfst Dd Haex Adhjn Fork thickness: 70 mm ISO class: ISO class 4 = 5,000 - 10,000 kg Mast type: Telescopic Transmission: Hydrostat Condition: Ready for use and fully functional Technical condition: good Front tires Type: Pneumatic Front tires Size: 17.5 R25 Front tires Condition: 60 - 80% Rear tires Type: Air Rear tires Size: 17.5 R25 Rear tires Condition: 60 - 80% Description: Full cab with heating and air conditioning, lighting similar to STVO, 3rd + 4th valve to fork carriage, joystick sideshift, fork positioner, Hydraulic sideshift Hydraulic fork tine adjustment (opening dimension inner edge - inner edge = 610 mm - 1,950 mm) 3rd valve, 4th valve, rear working lights, heating, soot filter, full cab, air conditioning, interior mirror, exterior mirror, joystick, windshield wiper, seat,

Condition: used, Year of construction: 2008, pressure 180 t chamfer lenght 3110 mm distance between columns 2600 mm column arm 410 mm ajustment speed 100 mm/sec working feed 10.0 mm/sec return speed 80.0 mm/sec back stop - adjustable max. 750 mm stroke 260 mm dayligth 460 mm table height 880 mm oil volume 210 ltr. operating pressure max. 240 bar control DELEM total power requirement 15.0 kW weight of the machine ca. 11.200 kg. range L-W-H 4250 x 2000 x 2800 mm Current new price approx. 85.000 euros Special price on request Features: - Electro-hydraulic CNC press brake - With DELEM CNC control model “DA 66W” * 2D graphic programming * Automatic bend sequence calculation and collision detection * High-quality LCD screen (TFT) * Swivel control panel, front left - CNC-controlled axes: Y1 + Y2 + X + R + CNC crowning - CNC electric motor-driven backgauge (X axis) * with 2x manually adjustable stop fingers Dsdpjxa Hivjfx Adhjcn - CNC electric motor height adjustment of the backgauge (R axis) - CNC electric motor table crowning - ROLLERI upper tool adapter (quick-change clamping) * including crowning device in the tool holder - 2x front, sliding support arms (“sliding” system) - Side guard (swivel doors) - Rear guard (sliding door) - 1x freely movable 2-hand/foot control - Operating instructions (PDF)

Condition: used, LVD Shear Type HST C-10/31 Capacity 3000 x 10 Dcodpfox Tqtbsx Adhon