Single Column Press - Hydraulic

WMW Zeulenroda PYE 25 SS

Condition: excellent (used), Year of construction: 1977, functionality: fully functional, total height: 27,500 mm, total width: 10,500 mm, total length: 16,500 mm, pressing force: 25 t, table width: 630 mm, table length: 500 mm, operating speed: 200 mm/s, overall weight: 2,400 kg, reverse speed: 450 mm/s, ram plate width: 450 mm, ram plate length: 360 mm, distance between stands: 800 mm, stroke length: 500 mm, power: 12.5 kW (17.00 HP), PYE 25 SS hydraulic press. Dodjtzxvwepfx Afnoun Year of manufacture 1977. manufacturer VEB Wema Zeulenroda (Germany). Parameters: Maximum pressing force 25 tons. Working pressure 16 MPa. Upper table 450 x 360 mm. Lower table 630 x 500 mm. Ground clearance 800 mm. Cylinder stroke 500 mm. Down speed 200 mm/sec. Upward speed 450 mm/sec. Power requirement 12,5 kW. Weight 2400kg. Height 2750mm, length 1650mm, width 1050mm. Technical condition of the machine very good. The machine after a general overhaul. It is possible to make a visual inspection and check the machine in motion.

Condition: used, Year of construction: 2008, x-travel 800 mm y-travel 700 mm z-travel 600 mm control SIN 840D Powerline spindle turning speed - stepless 1 - 8.000 U/min power capacity at 40 % load 28,00 kW spindle diameter in front bearing 80,00 mm spindle taper HSK-A100 B-axis 187 ° feed X/Y/Z-axis 15.000 mm/min Djdpfxjw Df A Sj Afnsun rapid traverse X/Y/Z 50,00 m/min feed force X/Y/Z axis 10.000 N rapid traverse B-axis 11,20 U/min size of pallet 800 x 630 mm table load 0,80 t c-axis 360,000 x 0,001 ° table turning speeds 1 - 500 U/min toolpiece magazine: chain magazine 120 Stück tool diameter 100 mm tool diameter with 2 vacant positions 160 mm tool length - max. 350 mm weight of tools max. 10,00 kg total power requirement 60,00 kW weight of the machine ca. 13,00 t dimensions of the machine ca. 7,40 x 5,30 x H3,50 m With Siemens SIN840D control, tool taper cleaning, tool breakage monitoring, coolant system, 2 pressure levels (40bar / 80bar), chip conveyor, operating mode 4, exhauster.

Year of construction: 2007, condition: refurbished (used), GF AgieCharmilles Progress V3 Year of manufacture 2007 Dujdpfx Aemmfwujfnen travels: X= 500 mm, Y= 350 mm, Z= 426 mm Travels U/V-axis: +/- 70 mm Maximum taper: 30° at 100 mm height Maximum workpiece dimensions: 1050 x 650 x 420 mm Maximum workpiece weight: 400 (in bath) / 800 (without bath) kg Achievable surface quality: Ra: 0.20 µm Maximum cutting rate: 500 mm²/min Available wire diameters: 0.15 - 0.33 mm Water bath machine with automatic wire threading and rethreading after wire breakage With manual front door (accessible from 1 side) Incl. AGIEJOGGER- hand box for comfortable set-up AGIE IPG-V generator AGIEVISION 5 control system Dimensions (length x width x height): 1940 x 2300 x 2600 mm Net weight: 3460 kg The machine will be cleaned and overhauled by us after receipt of order. You will receive a warranty of 6 months on all machine parts. We are also happy to offer you commissioning and training

Condition: ready for operation (used), Year of construction: 2010, FAT TUR 630AMN x 2000 CNC Siemens 840D Dsdpow Ecuusfx Afnsun Yom: 2010 Turning diameter: 630 mm Turning diameter over top slide: 370 mm Turning length: 2,000 mm

Condition: used, Year of construction: 1992, Technical details: spindle diameter: 100 mm x-travel: 1500 mm y-travel: 1450 mm z-axis: 930 mm w-axis: 506 mm B-axis (table): 360 ° control for program: HdH TNC 407 tool taper: SK50 number of spindle speeds: 5 - 1.600 / stufenlos table load: 4,0 t table-size: 1100 x 1400 mm table rotating: 360 ° feed steps: X/Y/W/Z-Achse: 2 - 2000 mm/min Rapid feed X axis: X/Y/W/Z-Achse 5000 mm/min. total power requirement: 40 kW dimensions electric cabinet: 2000 x 600 x 2000 mm machine dimensions LxWxH: 4,9 x 3,7 x 3,8 m weight of the machine ca.: 14 t Djdeu Idqbjpfx Afneun CNC drilling-milling machine with hydraulic power unit. Working paths from the table: X-axis table transverse 1500mm W-axis table longitudinal 1000mm 9x T-slots according to DIN 650 Equipment: measuring probe electronic handwheel hydr. weight compensation Y-axis universal milling head And some accessories, ask for them! i.D. *

Condition: used, Year of construction: 1965, core drilling diameter max. 50 mm bore depth 2000 mm swing diameter mm drilling capacity diameter max. 110 mm total power requirement 30 kW weight of the machine ca. 10 t Dodst Hwucepfx Afnsun Drilling Ø, approx. 2 - 50 mm Boring Ø, approx. 100 mm Drilling depth, max. (see stroke / mounting length) 1,600 - 2,000 mm Stroke of drilling slide, approx. 4,000 mm Distance between the two spindle heads 5,000 mm Height of centres above guideways 350 / 450 mm Drilling feed of drilling slide, infinitely variable 20 - 200 mm/min Quick feed of drilling slide 2,500 mm/min Spindle speeds via belt disks 260 - 650 / 650 - 1,625 rpm Workspindle drive 24 kW Drive of coolant pumps 1 x 7.5/15 kW and 1 x 15/28 kW Total electrical load, approx. 60 kW - 380 V - 50 Hz Total length of machine / guideways 7,500 / 5,000 mm Weight, approx. 10,000 kg Accessories / Special Features * Machine consists of the following elements: Main spindle on the left-hand side, followed by the coolant oil supply device. Table group, driven by ball screw spindle. Coolant oil supply device with elevated height of centres. At the end is a headstock, Type B 16, with drive motor approx. 7.5 kW, n = 900/2400 and 2400/6000. Large coolant device with filter unit. Large selection of accessories and drilling tools with Ø up to 100 mm. * Machine is suitable for working with a rotating workpiece together with a fixed drilling tool (ELB and BTA Process), as well as for a fixed workpiece and a rotating drilling tool. It can work with internal oil feed (Elb) or with external oil feed (BTA). * Complete oil coolant unit with tank and filter and two SIG high pressure pumps. Number of litres can be set: 17 / 40 / 120 or 220 / 500 litres per minute. Capacity approx. 2,500 l. * Feed of main slide is via ball screw spindle and infinitely variable DC motor. Mounted on the main slide is at present a table, approx. 800 x 800 mm, cross-adjustable approx. 500 mm, and suitable for holding cubic and cylindrical workpieces. Electric control via cam rail, approx. 2,500 mm long. End switch for quick feed, feed and return. * 2 closed 3-point steady rests. * FORKHARDT 3-Jaw Chuck, manually operated, Ø approx. 315 mm. * Modernized control panel with speed display, feed setting and display, display for kW, switch for feed, quick feed, right/left, etc. * 2 separate switch cabinets, separate coolant oil display device, bushes, reducers, clamping helps and lots of other accessories. This is a very valuable machine because of all the accessories!

Condition: reconditioned (used), Year of construction: 2002, 4200 x 2500 x 650 mm Table size The table moves 3000 mm outwards for loading For tools up to 4200x2500x1500mm Dedpfx Afjgphaxsnjun Tool weight up to 40 T Speed at 700 T still 62 mm/sec, at 1200 T still 35 mm/sec. ram size is 4200x1750 mm maximum open height 2200 mm drawing cushion with 50 to 500 T drawing cushion stroke 400 mm drawing cushion size 3100x1600 mm drawing cushion speed 150 mm sec. ram drawing cushion with 150 mm stroke 1600 mm stroke 475 KW, 890 Amps 210 T machine weight new motors new control system Was used for 3 years at a German automotive company and then sold to Brazil to an auto parts manufacturer. Worked there until 2020.

Condition: excellent (used), Year of construction: 1990, Force 25tons Throat 160mm Daylight 500mm Table size 650x650mm Ram size round 140mm Stroke 130mm Dodjfcw Apspfx Afnjun requested power 4 KW Weight 2000Kg height 2100mm width 1100mm depth 1500mm

Year of construction: 1981, condition: excellent (used), faceplate diam 1300mm max turning diam 1100mm range of turning diam 460-1250mm Duedpsk Dz N Ijfx Afnsn

Condition: new, turning diameter 325 mm turning length 1000 mm swing diameter over bed slide 250 mm Swingdiameter in the bed bridge 440 mm reus 12 (85-2000) U/min tail stock MK 3 quill stroke 100 mm diameter of quill 40 mm spindle taper DIN 55027 Nr. 5 spindle bore 32 mm feed längs 0,006 - 1,77 m/min feed quer 0,003 - 0,885 m/min total power requirement 2,2 kW weight of the machine ca. 770 kg Dsdstycpajpfx Afnjun dimensions of the machine ca. 2150 x 950 x 1350 mm Furnishing: - Cooling device - Machine light - chip rear wall - Spindle protection - Lathe chuck protection - Tool holder protection - Foot pedal with braking function CE - Interchangeable gears *incl. Optional equipment - 3-jaw chuck Ø 160 mm type 3204/ DIN6350, BISON - MULTIFIX quick-change holder type A, incl. 4 tool holders - 2-axis digital display DRO Newall