Sharpening machine

weinig Randomat 960

Year of construction: 1988, condition: repair required (used), mechanisation for planer infeed -For lengths up to ca. 13 m -Ideal unit for KVH (solid construction timber)and BSH (laminated beams) in front of the planer -1 operator -lateral destacking unit -separation Bledpfx Asvbtpocvsf -4 cross cut saws -cutting cross section 180x220 mm, 150x300 mm

Condition: used, No. 3176 Bjdpfeu Agh Sox Acvelf Automatic planer and moulder WEINIG Hydromat 1000 Used, year of construction 2007 6 spindles: bottom-right-left-top-top-bottom Electronic feed 6 - 60 m/min Working width 80 - 150 mm Working height 23 - 65 mm Finished slat widths 4 - 15 mm Max. Max. number of slats 16 pieces Slat lengths 400 - 4000 mm 1st spindle horizontal at the bottom Brake motor 11 kW, 6000 rpm Spindle diameter 45 mm Tool flight circle 125 - 180 mm 2nd spindle vertical right Brake motor 7.5 kW, 6000 rpm Diameter 45 mm Tool flight circle 112 - 250 mm Max. Moulding depth 35 mm Axial adjustment travel 80 mm 3. spindle vertical left 7.5 kW, 6000 rpm Diameter 45 mm Tool flight circle 112 - 250 mm Max. Moulding depth 35 mm Axial adjustment travel 80 mm Pressure shoe in front of the spindle, swiveling away, pneumatic roller contact pressure 4. spindle horizontal top 15 kW, 6000 rpm, diameter 45 mm Tool flight circle 112 - 250 mm Max. Moulding depth 35 mm Axial adjustment path 45 mm Split pressure shoe in front of upper spindle, adjustable and swiveling away, pneumatic 5. horizontal top spindle as saw spindle Brake motor 37 kW, 5000 rpm Diameter 45 mm Axial adjustment travel reduced to 25 mm Tool flight circle 112 - 250 mm Max. Sawing depth 35 mm Axial adjustment path 45 mm Split pressure shoe in front of upper spindle, adjustable and swiveling away, pneumatic 6. horizontal spindle at the bottom as saw spindle Brake motor 30 kW, 5000 rpm Axial adjustment travel reduced to 25 mm Diameter 45 mm Tool flight circle 112 - 250 mm Max. Sawing depth 35 mm Axial adjustment path 45 mm All moulder spindles with high-performance bearings Electronic feed 7.5 kW Adjustment travel of the feed rollers compared to the left-hand spindle, axial 35 mm Shorter roller distance compared to the right-hand spindles Running meter counter, electric, with 2 counters Short infeed table (1.2 m) with 2 driven rollers above the table 1 driven, toothed roller in the table, lateral pressure roller Automatic waxilite pump / lubricant pump Machine with 4-roller extension, pendulum shafts extended to 200 mm 2 driven, toothed rollers in the outfeed table 2 driven, toothed rollers in the machine table Pressure beam before and after upper spindle with mechanical digital display DigiSet (digital double display) for left and top spindles Electrical height adjustment of the upper spindles and the feed Machine already dismantled and stored Sale on behalf of customer, ex location near South Tyrol, without transportation and assembly Subject to errors in the description and price Transportation and loading by us optionally possible To avoid possible misunderstandings, an on-site inspection by appointment is possible and recommended Sold as is Technical details, condition description, year of construction and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: “purchased as seen” Images and videos serve as examples and do not represent the actual scope of delivery Terms of payment: Prices plus VAT, payment before collection or dispatch Terms of delivery: ex location

Condition: used, The Stenner VH105 double bandsaw with two movable saw blocks that allow one of them to be placed behind the feed system to cut with one saw or to feed timber through the saw without sawing, both without removing the saw blade. - Manufacturer: Stenner, - Model: VHET105, - Saw pulley diameter: 1050 mm, Blsdjtp E Uzopfx Acvjf - Saw blade width: 130 mm, - Feed speed: 10 – 80 m/min, - Distance between saws: 5 mm, - Distance between saws max: mm: 400 mm.

Condition: ready for operation (used), Year of construction: 2017, Number of boring spindles 4 St. Working width 230 mm Working height 160 mm Feed motor 11 kW Feed speed 60 m/min. Bedeyhfhnjpfx Acvelf Control Memory Plus

Condition: repair required (used), Year of construction: 2010, functionality: not functional, feed rate X-axis: 120 m/min, input frequency: 50 Hz, For sale is a Weinig mechanization system consisting of: Weinig 811, Weinig 820, Weinig 814, Bedpfxjv Skayo Acvjlf Weinig 811, Weinig 806

Condition: as good as new (ex-display), Please check in your junk mail if you do not receive a reply within 24hrs from sending your inquiry !!! CAN SHARPEN MAX 406MM DIAMETER CUTTERS !!! The G-716 Semi-automatic Cutterhead Grinder is used to sharpen 178mm to 406mm diameter eased edge, milled to pattern, and fingerjoint cutterheads. Worktable traversing is automatic and has adjustable stops. Cutterhead indexing is manual. Each knife is held against a positive stop while being ground !!! No Index Plate To Change No index plate to change when working with heads with different numbers of knives. The use of an index plate assumes that the knives and head separations are uniform throughout, which is often not the case. If the height of the knife is high or low, then the front face of the knife will vary from knife to knife making the task of grinding difficult. The one constant is the back face of the knife, therefore the use of an indexing stop against the back face will provide for accurate indexing regardless of the irregularities in the knives and head slots. Head Indexing and Wheel Feed: Manual Minimum / Maximum Diameter Cutterhead: 7″ Min./16″Max. 178mm Min./ 406mm Max. Worktable Feed: Air / Oil Travel (maximum): 12″ 305mm. Adjustable Limits: Proximity Switch Bodpsq Dzi Tsfx Acvolf Speed: Fully Adjustable Index Method: Manual index after each knife is ground. Grinding Spindle: 1-1/2 HP Wash Down Duty TEFC Motor 3600 RPM, Dual ABEC 7 Precision Bearings, with Sealed Lubrication. 8″ (203mm)Diameter Grinding Wheel (9″ 229mm Diameter Max.) Coolant System: 15 Gallon Tank with Casters, Sediment Tray Full View Sight Glass, 5 GPM Pump (120VAC) Wash Down Hose Included Specifications Grinds 7″ to 16″ diameter eased edge, milled to pattern, and finger joint heads Automatic traversing worktable with adjustable travel limits Manual indexing of knives against a positive stop with grinding position pneumatic brake allowing precision indexing without the need of an index plate High precision 1-1/2 HP grinding spindle with sealed lubrication Recirculating adjustable flow flooded coolant system with wash down hose Fully enclosed grinding chamber with viewing windows and task light Grinding wheel feed allows unattended operation. New Proscale.

Condition: used, Year of construction: 2003, feeder rollers, transfer belts for 6 meters, retractable forks, lift tables with rubber-coated parcel drive chains, outfeed chains Blsdpoycxtyofx Acvef

Condition: good (used), Year of construction: 2003, functionality: fully functional, Weinig Hydromat 23C four-side planer moulder Manufacturer: Weinig Model: Hydromat 23C Year of manufacture: 2003 Spindle configuration: 5 spindles Configuration: bottom, right, left, top, bottom Machine description: For sale: Weinig Hydromat 23C four-side planer moulder, year 2003, equipped with 5 spindles in bottom, right, left, top, bottom configuration. This is a solid and proven industrial machine designed for four-side planing of solid wood, production of moulded parts, timber sections, strips, joinery components and furniture elements. The Hydromat 23C is known for its stable construction, good machining precision and suitability for continuous industrial production. Typical specifications for this series include working width up to 230 mm and working height up to 160 mm. Market listings for Hydromat 23C also show versions with mechanical or hydraulic feed and variable feed speed. Technical data: - Machine type: four-side planer / moulder - Number of spindles: 5 - Spindle arrangement: bottom, right, left, top, bottom - Working width: up to approx. 230 mm - Working height: up to approx. 160 mm - Series configuration range: from 5 to 10 spindles - Standard feed speed: approx. 6–36 m/min Features and advantages: - Solid industrial construction - Proven Weinig technology - Good machining quality - Suitable for continuous production - Good solution for serial timber processing Bedjyu Uqrjpfx Acvolf - Universal 5-spindle arrangement for planing and profiling Condition: Used machine Note: Technical details may vary depending on the exact machine configuration, motor powers, spindle diameters, feed system and optional equipment.

Condition: used, Year of construction: 2002, functionality: fully functional, machine/vehicle number: 96409, type of input current: three-phase, input voltage: 380 V, power: 73 kW (99.25 HP), input frequency: 50 Hz, input current: 159 A, We offer this used Weinig Unimat 23 moulder, year of construction 2002. Machine number: 96409 Machine type: Unimat 23 Year of construction: 2002 Circuit drawing number: B.96409 Operating voltage: 3 x 380 V 50 Hz Control voltage: 230 V 50 Hz Bljdpfsx Ttydsx Acvsf Nominal current most powerful motor: 29 A Nominal current: 159 A Main fuse: 160 A Power: 73 kW If you have any questions or need more information, feel free to send us a message or give us a call.

Condition: good (used), Year of construction: 2006, functionality: fully functional, machine/vehicle number: 106531, working width: 230 mm, power: 75 kW (101.97 HP), input current: 163 A, table width: 230 mm, Equipment: cabin, Rarity! Four-side planer Weinig Powermat 500 with splitting unit!! (the last two spindles fitted with saw blades, anti-kickback device, splitter wedge) for sale complete with all accessories. The machine has 7 spindles/shafts (bottom / right / left / top / bottom / right / left). Bledpfx Ajyyw Ufjcvjf We used the line to produce middle layers for three-layer board manufacturing. The machine is in perfect working order. The machine is still in operation and can be demonstrated. Further technical details will follow in the next few days...