Eccentric Press - Single Column

WEINGARTEN ARP 250 (UVV)

Condition: used, Year of construction: 1977, pressure 250 t stroke 40 - 190 mm no. of strokes 40 /min throat 500 mm passage to the back 1050 mm dayligth 615 mm table surface area 1380 x 880 mm hole in the table 450 mm table height over floor 800 mm ram surface 1200 x 800 mm ram adjustment 125 mm Fsdpfsvuuaisx Ambogd power requirement 22,0 kW Weight 24,0 t dimensions of the machine ca. 2,0 x 2,5 x 3,95 m x m x m permitted for manual loading according to the German Safety Regulations (UVV) with motor, pneumatic clutch/brake combination, hydraulic overload protection in ram, pneumatic counterbalance in ram, motoric ram adjustment, manual stroke adjustment, motoric centralized lubrication, bolster plate, two-hand operation

Condition: used, cone distance min./max. 0-108 mm Pitch angle min/max 5°/84° Control GE Fanuc Series 0-GC Pitch diameter (1:1 ratio) 152 mm pitch diameter (10:1 ratio) 216 mm Diametral pitch (finest/coarsest) 1.3/8.5 Mod. Face width gear wheel max. 35 mm Fgedeyh Rmmjpfx Ambed Knife spindle - Speed range 41-121 U/min working spindle speed range 0-33.33 U/min weight 9025 kg dimensions of the machine ca. 2707 x 2720 x 2200 mmxmmxmm Equipment/accessories: - 18-piece cutter set - Chip conveyor - Technical documentation

Condition: used, Year of construction: 1970, machine/vehicle number: 120895, pressure:63 t throat:250 mm stroke:8 - 100 mm no. of strokes:120 Hub/min table::715 x 500 mm dayligth:330 mm ram adjustment:63 mm clamping plate:700 x 480 mm hole in the table:240 mm Hole in clamping plate:110 mm dimension of ram:450 x 280 mm weight of the machine ca.:5,5 t dimensions of the machine ca.:1,2 x 1,7 x 2,7 m hydraulic tilting single column eccentric press, tilting in 4 steps, opening to rear (325 x 500mm) and below (360x160mm) with central lubrication via hand pump, additional clamping plate 700 x 480 x 850 mm, two-hand operation, foot-trip operation possible, operating-mode Fgsdjfx Hv Hopfx Ambjd selector for adjustment of continuous or single stroke, emergency cut-off, piece counter, various accessories

Condition: good (used), Year of construction: 2020, functionality: fully functional, cooling capacity: 20 kW (27.19 HP), type of input current: three-phase, type of cooling: air, overall weight: 281 kg, input voltage: 400 V, total width: 600 mm, total length: 1,600 mm, total height: 1,800 mm, warranty duration: 6 months, heating capacity: 20 kW (27.19 HP), Aircooled chiller/Heat pump SYSTEMAIR SYSCROLL 20 AIR EVO HP 20 kW/20 kW Cooling capacity: 20 kW / 5.69 tons (12/7 — 35°C) Heating capacity: 20 kW / 5.69 tons (40/45 —7°C) Year of manufacture: 2020 Options: Heat pump. Hydraulic module Refrigerant circuit: 1 pcs. Heat exchanger: Plate Condenser: Copper / Aluminum Compressors: 1 pcs. Mitsubishi Electric ANB42FPJMT (scroll) Type of refrigerant: R410a Number of fans: 2 pcs. Fsdewp Dq Sspfx Ambjgd Hydraulic module: 1 pcs. water pump EBARA matrix 5-2t Dimensions: 1.6x0.6x1.8 m. Weight: 281 kg. Working hours: 2330 h. Condition: Good CONDITION, TESTING & READINESS The chiller / kaltwassersatz / undergoes seven stages of technical inspection and operational parameter verification. It is also tested at our own test station, with connection to water (or glycol) and adjustment of parameters according to your requirements. After testing, you will receive a detailed report with the operating performance and the overall condition of the chiller. The chiller / kaltwassersatz / is ready for transport and commissioning. Our engineers will assist you with cooling capacity calculations, selection of the appropriate cooling scheme, and configuration of the required equipment options. WARRANTY & SUPPORT The quality of the equipment is confirmed with a warranty ranging from 6 to 36 months. Our company can also offer: - refrigerant charging; - replacement of oil and filters; - technical support. LOGISTICS - Worldwide delivery available - Support with loading, export documentation, and logistics coordination Get a detailed consultation. Photos, videos, and a full testing report can be provided immediately upon request.

Condition: excellent (used), Year of construction: 1995, Combination Unit: Manufacturer: GSG Feeder: Type: 840.02-027 Crusher Descaler: Type: 663.02-017 Wire Range: Ø5.5-16mm For wire rod with approx. 40-60 daN/mm² strength Fsdpfxjr Nfvmj Ambsgd Crushing and Bending Rollers: Carbide Inserts Adjustment with 0.37 kW - 1.15 A gear motor Brush Drive with 0.25 kW gear motor, n=293 rpm Connection Voltage: 380-420 V 50 Hz Dry Coating Unit: Type: BSG/T Filling: Calcium Stearate (e.g., Traxit Type: D S 51 E) Stearate Consumption: approx. 350 g per t of wire Drawing Speed: max. 15 m/s Electrical Power: 2x 0.55 kW gear motors Cassette: 2 slots (supplied with 1x roller block + 1x cassette) Type: PKG/T (TS) Cleaned rolled wire Wire strength approx. 40–60 daN/mm² Wire range max. inlet diameter 9.5mm, finished diameter 3.5–8.5mm Roll dimensions min. Ø115mm, max. Ø125mm, Bore diameter Ø82mm, width 15–25mm Cooling pin diameter 25mm Cooling water consumption approx. 600 l/h Drawing machine: Manufacturer: Koch Type: KHZ 5000 Year of manufacture: 1993 Serial number: 13.821 Number of draws: 1 draw per block Drawing drum: Ø700mm Tensile force: mechanical 5000 N Wire material: mild steel wires Run-in strength: approx. 40 – 45 daN/mm² Maximum drawing range: Inlet diameter 5.0 – 8.5mm Cross-section reduction: 20 x 25% (mechanical gradation) Drawing speed: up to max. 7.0 m/s Brake: Twiflex, type: MRB Drive: AC motor/frequency converter, Siemens PN=110 kW, n=1485 rpm Spooler: Manufacturer: Koch Type: KHS 1250 Year of manufacture: 1993 Factory No.: 13741 Wire diameter: 5 – 8.5 mm Strength: approx. 55 – 70 daN/mm² Winding speed: V=7 m/s, adapted to the drawing machine Filling weight: approx. 3000 kg Spool drive motor: Three-phase motor with external fan Type: 1 PQ 6253 – 6 AA 70- Z A 15 + K 20 + C 14 + H 46 P=37 kW, n=1000-2000 rpm, IP54, design B3 Laying drive motor: 66-671U, 1.5 kW, 170 V, 9.8 A, 1680 rpm, IP 44, B5-200 With Attached tachometer generator TG 20, 20 V / 1000 rpm With attached spur gear SK 32, i=57.53, design B6 Hydraulics: Hydraulic excavator type: H13 AK Pneumatics: Twiflex disc brake type: MRB Pneumatic cylinder type: SPWG 28032-25mm stroke Dimensions: 3100 x 3000 x 1700 mm (L x W x H) without counterweight

Condition: used, Year of construction: 1978, machine/vehicle number: 150 359 - 11683, functionality: fully functional, For sale are the PS160 (2 units) and the PS140 (1 unit). One is 250 metric tons, the other is 140 metric tons. The PS160 is one of the complete machines and is in operation; the PS160 does not have the control cabinet. The machines are for sale as a single unit and individually. Inquire by phone or email! Fgjdpfxot Ucpbe Ambed

Year of construction: 1987, condition: used, sheet width 150 mm coil weight 80 kg Fedpfx Ajfn Aqlembsgd coil external diameter 650 mm 1000 mm diameter of the mandrel 230 - 445 mm total power requirement kW weight of the machine ca. t dimensions of the machine ca. m

Condition: used, Year of construction: 2017, CNC gantry plasma cutting machine (beveling unit) Manufacturer: Zinser Fjdpfjw Rpvbsx Ambegd Type: 2425-I/3600 Year of manufacture: 2017 CNC control: 5010 Travel length: 11 m Oxy-fuel cutting table with oscillating conveyor system, including dust extraction system Dimensions: 2,000 x 8,000 mm 1 plasma torch with Hypertherm XPR300 power source automatic gas console including automatically rotating plasma beveling unit Bevel System 2015/350 Downflow filter system 3DFP9-SP Power: 9 kW Laser diode 3726

Condition: ready for operation (used), Year of construction: 1998, power: 37 kW (50.31 HP), pressing force: 250 t, stroke length: 150 mm, table width: 900 mm, table length: 1,000 mm, overall weight: 16,000 kg, Very nice and well maintained hydraulic press. 250 tons pressing force. Approximate dimensions: H: 380 cm. W: 200 cm. L: 200 cm. Weight: 16,000 kg. Fgjdpfx Amery Trpjbjd Can be loaded by crane on collection against payment. Transportation can be arranged. Sold for customers. Location: DK-7600 Struer. Make an appointment for a demonstration.

Condition: used, material width 300 mm coil weight 3 t material thickness 2 - 4 mm Fgedpfx Amjcdrmmobed Straightener, 7 rolls, Make. Schleicher, Type RM 6-95/160 - band width 300 mm - band thickness 2 – 4 mm - cross cut 1200 mm² - voltage 220/380 V 50 Hz - total power requirement 3,1 kW coiler with press roll, Make Schleicher, Type H-3 - Coil weight 3 t - Band width 400 mm - voltage 220/380 V 50 Hz - total power requirement 3,92 kW without control