BRUSHING MACHINE + SANDING MACHINE

WANDRES CH 29 M/900/1300 + BI 99 DS/3/1300 + HSC

Condition: excellent (used), Year of construction: 2015, I sell the 2-head UV-drying tunnel Superfici Essiccatoio UV Gkodpfxjffk Ets Acisb Model: Poliedra S.Cure 1650x2 + TT1 3500. Year 2015. Available immediately. Repairs needed: Display, Energy power units for each two UV-units

Condition: like new (used), Year of construction: 2019, Vacomat 350 XP TWIN The Vacomat 350 XP TWIN is a high-performance dust extraction unit and a true energy-saving marvel among mobile dust extractors. Two frequency-controlled motors (5.5 kW each) ensure that the suction power is adjusted accordingly, especially under highly variable operating conditions. This ensures that only the energy that is actually needed is consumed. This dust extractor handles air volumes of up to 10,000 m³/h and is ideally suited for extracting dust from large CNC machines or entire machining centers. The innovative and highly intelligent control system automates the extraction process in conjunction with the connected machines. Extraction starts automatically as soon as a connected machining center is switched on. If the power requirement is lower, only one fan is started. As soon as several extraction points are in operation, the second fan is automatically switched on. As standard, the filter sleeves are cleaned automatically during operating breaks, as soon as all connected machining centers are switched off. Our patented filter shaking system then ensures gentle cleaning via a pneumatic/mechanical process using a compressed air connection (inlet pressure 6 bar, air consumption per cleaning cycle approx. 11 l). Optionally, and particularly recommended for very high and extremely fine dust concentrations, such as gypsum dust, an efficient pressure pulse cleaning system is available. The cleaning process via the compressed air tank takes place offline, after the extraction operation (NOTE: height then +100 mm and length +350 mm). Our Vacomats are manufactured using a modular system. As standard, the dust and chip mixture is discharged into four dust-tight chip collection containers (4 x 120 l) with durable plastic liners. A negative pressure channel securely holds the foil bags in the collection container. Viewing windows make it easy to check the fill level. Low energy consumption thanks to a modern, high-efficiency motor (IE3) "Made in Germany" and a flow-optimized internal housing with low air resistance. Heat recovery through a recirculation system: The warm exhaust air is filtered and fed back into the workshop. Low noise level: A double-walled filter sleeve housing absorbs the extraction noise directly inside the Vacomat. In addition, the fan housing is soundproof. Approved for indoor installation in the wood dust area - manufactured according to the new DIN EN 16770 standard. Healthy return air: High-quality, specially developed filter materials made of antistatic polyester needle felt filter out 99.9% of dust and chip waste from the air (dust class M for St 1 dust, according to TRGS 553). Increased safety through fire and explosion protection measures according to DIN EN 16770: pressure pulse tested up to 20,000 Pa, automatically activated powder extinguishing system - no water damage! Gjdpszp Edwjfx Acijkb Operational reliability: A pressure gauge continuously monitors the extraction performance. Error messages are displayed by the signal light. Low follow-up costs due to high-quality components and long service life of the filter medium: For example, an extra-large settling chamber ensures an initial separation of coarse chip waste. This prevents the filter sleeves from being additionally loaded with material. Low maintenance effort thanks to the maintenance unit on the motor console and easy access to the inside of the filter. All specifications according to the manufacturer.

Year of construction: 2017, condition: used, Used machine Gkodpjx Rpgbjfx Acisb Year of manufacture: 2017 The Barbaric TSRET04 return system is a workpiece return unit for edge banding machines. It is the most basic version in the TSRET series and serves the following functions: - Transfers the workpiece at the end of the edge banding machine - Returns the workpiece to the height of the infeed of the edge banding machine Functionality After passing through the edge banding machine, the workpiece moves onto a roller table. The transfer is carried out by belt conveyors moving perpendicularly to the conveying direction, which rise from the roller table, lift the workpiece, transport it sideways, and set it down on a slightly lower roller table. This roller table conveys the workpiece to a belt conveyor. At the end of the belt conveyor, a non-driven, slightly inclined roller conveyor toward the edge banding machine’s infeed is connected. A stopper halts the workpiece at the end of the roller conveyor. Technical data - Max. load capacity: 60 kg - Max. panel size: 2,800 x 1,300 mm - Cycle time: max. 11 pieces/min Dimensions: - Return: 2,293 x 1,961 mm - Conveyor belt (L x W): 2,500 x 800 mm - Roller conveyor (L x W): 2,000 x 800 mm - Total length: approx. 6,943 mm - Total width: approx. 2,239 mm Availability: short-term Location: Flörsheim

Condition: excellent (used), Year of construction: 2024, operating hours: 4,000 h, functionality: fully functional, machine/vehicle number: 111549, air demand: 6 m³/h, operating pressure: 6 bar, total width: 1,300 mm, type of input current: three-phase, inner dimension length: 8,000 mm, I am pleased to present a custom-built Rosler 100-4 HD machine. This machine is used for shot blasting steel parts, where a high surface roughness is required. - Year of manufacture: 2024 - Machine operating time: 4000 hours - Mesh conveyor belt made of manganese steel, 1000 mm wide - Adjustable speed of the conveyor belt - 4 turbines, power 11 kW, Rutten Gamma 330 HD model - Continuously variable turbine speed control Godpfx Acjwvgbgeiekb - Automatic part detection - Automatic abrasive flow control - Automatic abrasive filling - Automatic part blow-off - Rosler BF 40/40 dust collection system - The machine is additionally equipped with a wet dust collector, which enables the shot blasting of aluminum parts (additional installation fee applies). - Hot Spot chamber made of manganese steel and tool steel - The machine allows operation with media of the highest hardness (GH, sharp-edged) or cut shot, making it an ideal solution for the rubber industry, where high surface roughness is needed during the rubber vulcanization process. - Turbine blades made of cemented carbide guarantee 30,000 hours of operation. - Turbine housings made of cemented carbide provide even greater protection against wear and tear on the machine body.

Condition: good (used), Clean air extraction system Used machine, in good condition Images to follow mobil Jet 160, Gkjdpfx Asrb D Nscisb Connection 160, Fan 2.2 kW Air flow rate 1850 m³/h, 400 V

Condition: used, machine/vehicle number: 008005, Max width workable: 2440 mm Gksdpfx Ajwu Aacscieb

Condition: used, machine/vehicle number: 007307, Max. working width: 3200 mm Max. working thickness: 60 mm Gjdpfxeuaq D Ao Acijkb

Condition: used, Year of construction: 2018, Vertical CNC boring and machining center Workpiece length 200 - 3,050 mm Workpiece width 70 - 850 mm Workpiece thickness 12 - 60 mm Milling spindle 1 unit Main spindle power 5 kW Max. speed 18,000-24,000 rpm (depending on configuration) Tool interface HSK-F63 or ETP25 Tool changer 4-position magazine Vertical boring spindles 13 Horizontal boring spindles X 4 Horizontal boring spindles Y 2 Nut saw X-direction Gsdpfxezuw Dto Aciokb Control system Homag powerTouch / Power Control PC 86 Software WOODWOP 7.x Total connected power 11.5 kW Compressed air requirement 7 bar Machine weight approx. 1,580 kg Installation dimensions (L W H) approx. 2,950 1,984 1,895 mm CE marking

Year of construction: 2002, condition: used, machine/vehicle number: 001, Description Offered is an automated side board processing line with singulation, trimmer for end trimming, 2 stacking machines, additional discharge, and end trimming of stacking slats: Boards 2000-5280 mm long, 16 - 40 mm thick, 70 - 260 mm wide, cycle rate of 29 or 58 pieces/minute, operated by one person sitting at a joystick: - Boards are conveyed laterally using a 4-strand overhead chain cross conveyor - Singulation steep conveyor 6000 mm wide, 3000 mm inclined - Alignment roller conveyor - Chain cross conveyor as a layer former - Star turner and sorter before the trimmer Nlewsy Uzhfj D A Tmcob - Edge detection (ALFHA-Edger) - Trimmer with 11 saws in a 50.5 cm grid: The operator (sitting) at the joystick assesses: without re-trimming, 5000 mm to stacking machine 1, alternatively: without re-trimming, 4000 mm to stacking machine 1 Gkodpfxoy Uzldo Acieb with re-trimming, 4000 mm to stacking machine 2 with re-trimming, 3000 mm to stacking machine 2 with re-trimming, short lengths for discharge into a box, with re-trimming, short lengths for discharge into a box with re-trimming, 2 or 3 x 101 cm for stacking slats, with re-trimming, 2 or 3 x 101 cm for stacking slats or waste cut - trimming length 505 mm for the underlying vibration channel - 2 stacking machines: 1 x 2500 to 5280 mm and 1 x 2000 to 4280 mm - automatic lowering of the finished packages and transfer to automatic strapping - FROMM strapping with 16 mm plastic band and automatic transfer to the discharge roller conveyor - ALFHA control with Siemens S 7 - ensures perfect operation. Performance records / daily logs - Control cabinets with Siemens components, SEW motors, Telco light barriers For example, one employee processed, packaged, and strapped approximately 15,000 boards of side lumber 4000/17 x 76 mm in 9 hours. The system is still assembled, but the upstream chipping plant has already been dismantled. Therefore, the system is immediately available. It is very robustly built and has always operated smoothly and without any problems. A video of the process can be shown via WhatsApp!

Year of construction: 2005, condition: used, CNC Machining Center Elumatec SBZ 122, year of manufacture 2005, designed for machining aluminum profiles for windows, curtain walls, and light metalwork. This is a robust and reliable industrial machine, highly regarded for its machining precision and operational continuity. Main features: - 3-axis CNC machining center - High-rigidity steel frame - Vertical spindle for milling, drilling, and complex operations - Worktable with pneumatic vices for stable and precise clamping - Long-travel longitudinal axis, ideal for processing profiles of considerable length - Protective enclosure with chip conveyor - Elumatec CNC control unit - Ideal for medium to high production and repetitive operations Applications: - Milling - Drilling - Slotting - End and face machining - Production of aluminum frames and special profiles Gkedpjyg Ht Asfx Acisb Key data: - Manufacturer: Elumatec - Model: SBZ 122 - Year of manufacture: 2005 - Condition: Used Condition: - Machine in good overall condition - Coming from an industrial environment - Can be seen in operation by appointment Included equipment: - Complete workbench - Pneumatic clamping system - Control panel - Original covers and safety guards