Vibrator 2 tubs

Walther Trowal TA 2/145

Year of construction: 2011, condition: good (used), Offer 24370 Technical data: - Sludge filter press JUNGHANS with cylinder unit + conveyor belt - Flocculation unit - pumps - Switch cabinet with electrical equipment - Aluminum water collection tray in the complete container floor - Lighting system - Sea container with 4 doors - Space requirement approx. W 6.0 x H 2.4 x D 2.4 m Bdjdpfx Ajt Srkpjcvja - Weight approx. 5000 kg - Separate conveyor belt L 8.0 m

Condition: new, Year of construction: 2023, Horizontal bending machine AH 40 - ZOPF - with semi-automatic control - hydraulic pressure 40 to. - length of stroke - bending speed adjustable - max. working speed 10 mm/sec. - return speed 20 mm/sec. - hydraulic pressure adjustable - maximum bending high 250 mm - motorcapacity 3,0 KW - 400 V 50 hz 3 ph. - working height 900 mm - closed table - replaceable wear plate - weight 950 kg - bending capacity: Bedsqvm Ukspfx Acvoda flat material max. 150x22 mm round tube up to 60 mm

Year of construction: 2000, condition: excellent (used), daylight width: 170 mm speed: approx. 25 m/min working direction: any work roll diameter: 120 mm Bdjdep E Eglepfx Acvja barrel length: 150 mm backup rolls: backup block/chain

Year of construction: 1990, condition: used, machine/vehicle number: 9072492, nominal capacity: 100 kVA throat: 500 mm spark plug air gap: 330 - 500 mm electrical connection: 400 V kW Bdsdsz H Dyepfx Acvea space needed: 700 x 1420 x 2000 mm weight: 750 kg

Condition: new, Year of construction: 2025, * 250 lt Net Volume * Dosing pump included. Bodpfxsh I N Udo Acveda * Highly wear resistant P.U.Lining (90 Shore) * High performance three phase current drive motor. * Changeable valf for the wastewater decharging * Main swicth and emergency stop switch. * Timer and working hours timer * Special construction of control panel(EU Standarts) included

Condition: excellent (used), Zwick Type: BZ2.5/TN1S Zwick table testing machines Tensile strength measuring machine Area of application: Wide range of applications, from plastic and elastomer testing to paper, textile, foam and wire to component testing. Load frame: Max. test force FN in tension/compression direction 2.5 kN Height (h1) approx. 770 mm Width with electronic unit 320 mm Depth with electronic unit 414 mm Height of the work area h min ... h max: Traverse angle mounted upwards 227 ... 573 mm Traverse angle mounted rotated by 180° 57 ... 403 mm Bdedofnm Dqopfx Acvoa (each without connection bolt) Connection values: Electrical connection 115/230 V 4/2A-1PH/PE/N Power consumption 0.4 kVA Mains frequency 50/60 Hz 2.5 kN Condition: used Scope of delivery: (see image) (Changes and errors in the technical data, information are reserved!) We will be happy to answer any further questions you may have over the phone.

Condition: good (used), Zwick Type: BZ1.0 / TH1S Zwick table testing machines Zwick with a maximum force of 1.0 kN. The course of the traverse: 1150 mm. Testing speed: 0.1 ... 1800 mm / min Bjdpfxoddante Acvsda Scope of delivery. (See pictures) (Changes and errors in the technical data, information is subject to change!) We will be happy to answer any further questions you may have over the phone.

Condition: new, An additional aircompressor are required to enable the nitrogen generator to produce nitrogen. Nitrogen purity: 99.999% Input pressure: 8Bar Bdodpsxfrv Eefx Acvsa Output pressure: 7Bar Power: 75W(Power is the cost per hour to produce nitrogen ) 3 în 1 design, no need for extra air compressor and refrigerator or dryer Gas clean

Condition: new, Year of construction: 2026, Product characteristics The plasma burner or oxygen-gas CNC1 burner is a mobile device designed for cutting shapes out of a metal sheet. The machine does not require anchoring, thus reducing the assembly time considerably. Additionally, it enables for placing the machine in any location within the hall without any new expenses. The machine is equipped with an excellent quality wheel system that together with the low weight portal makes the plotter one of the fastest machines available on the market. The machine can be used for manual and automatic cutting. It is equipped with a digital controller that enables cutting out complicated shapes. The machine proves itself very well in the shipbuilding, machine-building and power industry. CNC1 has been equipped with a precise system of X/Y axes guides. The burner is controlled by Sino-USA electronic production system that is characterized by a high precision and elimination of the errors occurring during operation. The machine is very easy to configure. A manual configuration is possible for simple shapes and automatic configuration is possible for more complicated figures. The cutting pattern and the burner motion are shown on a display. An original FastCAM software is attached to the machine for easy configuration. The software is in English which makes the work easier. FastCAM is a technological CAD/CAM program, which is intended for designing and defining cutting paths of the elements cut out by CNC burning machines. The program shall be installed on an office PC or on a portable computer. After defining the way of cutting the operator receives a ready control code, which should be transferred to the control system of the machine. FastCAM program is a standard element of our machines. BASIC INFORMATION User-friendly interface – easy operation, even for people without prior experience of working with such programs as FastCAM Import of drawings in the *.txt format from any programs similar to e.g. AutoCAD, SolidWorks etc. MAKRO – a library containing standard shapes enables creating figures without the necessity of drawing them in CAD system. The program provides 2D figures NESTING – an optimal usage of sheet metal thanks to the automatic arrangement of elements on a sheet DEMO – shows a working path without having to turn on the plasma source or oxygen VOLTAGE HEIGHT CONTROLLER The machine is equipped with THC (a voltage control of the plasma burner blowtorch height). A precise control (+/- 0.1 mm) of the plasma blowtorch distance from a sheet metal during cutting. Higher accuracy and absence of defects which capacitive sensors and roller disks have. The parameters of the controller are collected automatically from the Automatic Cutting Parameters Selection table. Technical data Power supply 230 V LCD 7" color Code format G-Code Working dimensions 1500×3000 mm Cutting speed 50–3000 mm/min Illustrations are preview only, the device is sold without the table. Bdodevxhwvspfx Acvoa Manufacturer: Cormak

Condition: refurbished (used), Year of construction: 2021, operating hours: 850 h, functionality: fully functional, In addition to the mentioned and pictured machines, we have many other machines and accessories (blasting systems, conveyor belts, and small machines) available from stock. The machines can be purchased or rented. Bdsdpfx Acjwfdbcovoa Contact us for (free) advice in the field of vibratory finishing, tumbling, and blasting technology.