Clamping plate with T slot

unbekannt 1500/3510/H950 mm

Condition: new, empty load weight: 17,250 kg, maximum load weight: 48,700 kg, overall weight: 66,000 kg, axle configuration: 3 axles, loading space length: 7,550 mm, loading space width: 2,480 mm, loading space height: 375 mm, tire size: 245/70 R 17.5, color: grey, operation weight: 17,250 kg, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm -Gooseneck can be raised/lowered and removed hydraulically -For tractor units: 6 x 4 and 8 x 4 (or 6 x 4 with optional 1-axle dolly) Low bed: -Low bed with external supports, designed as a telescopic tank bridge in low construction with extension at the front -Length x width approx. 7,550 mm x 2,740 mm -Mechanical locking of the extension Chassis: -Chassis at the rear with closed outer frame -Checker plate covering and continuous prism excavator trough approx. 1,450/900 x 505 mm, open at the rear Axles, suspension and tires: -"PENDEL-AXLE", all axles hydromechanically forced steering -Hose rupture valve on the axle compensation cylinder with automatic RESET function -Hydraulic cylinder with shut-off valves and pins for securing in raised position -Final painting of axles with 2 layers of 2-component paint in a single color in "FAY-Gray-34-0260" -Technical axle load 12,000 kg -Hydraulic axle compensation -245/70 R 17.5 Accessories: -Steel bulkhead, plug-in, approx. 400 mm high -4 wheel chocks -Gooseneck in the rear upper area closed with a removable cover -1 pair of steel ramps with climbing strips and fastening bolts to bridge the hooks of the low bed -The ramps can be placed over or between the hooks -Fastening options for the steel ramps at the rear between the outer supports of the gooseneck -One Locking point approximately every 1,000 mm on the extension -1 lashing ring on the left and right on the front cross member -Connection strip for supply lines to the tractor unit, attached at the height of the outer frame profile -6 pairs of threaded blocks on the outside of the inner supports of the loading area for mounting screwable rings M24 -6 pairs of countersunk lashing rings on the outside of the outer supports of the loading area, foldable inwards and outwards -1 pair of threaded blocks at the front and rear of the outer supports of the loading area for mounting screwable rings M24 -Hanging strip for loose aluminum loading ramps on the vehicle's end cross member -Central lubrication system with 2 pumps, BEKAMAX brand -Steering from the front and rear, operated by cable remote control, with alignment control of the axles -3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches -Removable loading floor (galvanized) in 3 elements can be inserted between the outer supports with hardwood flooring -Foldable extensions, by approx. 230 mm per side -Extension planks, loose, framed in steel -4 warning signs approx. 423 x 423 mm -Radio remote control for operating the steering -3.5" king pin -Anti-slip sticker on the left bevel of the gooseneck -Hydraulic connections from the gooseneck to the low bed with multi-coupling instead of screw couplings -Guide plate from the gooseneck for the fifth wheel plate, approx. 800 mm wide -1 spare wheel with mounting adapter -Parking position on the gooseneck for the warning signs when not in use -2 pairs of stake pockets embedded in the outer frame of the chassis, for plug-in stakes approx. 100 x 50 mm Godpfx Aoh Hm Tzjmusit -Dipper handle recess of the rear chassis closed at the back with a plug-in plate -Color of the trailer MB 7350 Novagrau

Condition: new, empty load weight: 12,900 kg, maximum load weight: 34,100 kg, overall weight: 47,000 kg, axle configuration: 2 axles, loading space length: 6,850 mm, loading space width: 2,540 mm, loading space height: 350 mm, suspension: other, tire size: 245/70 R 17,5, color: grey, operation weight: 12,900 kg, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm -Gooseneck can be raised/lowered hydraulically and removed -Technical fifth wheel load: 23,000 kg -For tractor units: 4 x 2, 6 x 2 and 6 x 4 Loading area: -Low bed with external supports in extendable "SUPER LOW" design, length approx. 6,850 mm -Low bed with solid hardwood floor approx. 40 mm thick and mechanical locking Rear chassis: -Rear chassis with closed external frame, checker plate covering and continuous prism excavator trough approx. 1,250/700 x 505 mm, open at the rear -2 pairs of lashing rings that can be folded outwards -1 pair of lashing rings lying in the trough -2 pairs of stake pockets for plug-in stakes 100 x 50 mm in the outer frame Pendulum axle and tires: -"PENDEL-AXLE", all axles hydromechanically forced steered -Hose rupture valve on the axle compensation cylinder with automatic RESET function -Hydraulic cylinder with shut-off valves and pins for securing in raised position -Final painting of axles with 2 layers of 2-component paint, painted in a single color in "FAY-Gray-34-0260" -Technical axle load: 12,000 kg -Hydraulic axle compensation -Tires 245/70 R 17.5 -TPMS tire pressure monitoring system in accordance with ECE R 141 Accessories: -Preparation for screw-on container positioning for 1x 20ft or 1x40ft container on the outer supports -2" kingpins -A galvanized steel front wall approx. 400 mm high -One spare wheel -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks -Steering from the front and rear can be operated using a cable remote control via push buttons, with alignment control of the axles -Hydraulic connections from the gooseneck to the low bed with multi-coupling instead of screw couplings -Electro-hydraulic unit -White reflector tape in accordance with EU regulations on the side, on the extension and at the rear -European reflector signs (red-yellow) on the rear of the trailer -One holder for the warning signs including a socket on the gooseneck and on the rear panel on the left and right -6 pairs of threaded blocks between the lashing rings under the top strap on the outer support for mounting screwable RUD rings VLBG-4 -ALU side walls and rear wall can be plugged into the gooseneck approx. 2,440 x 400 mm -The rear galvanized plug-in stanchions are removable (Length of the body approx. 2,560 mm) -Gooseneck in the rear upper area closed with a removable cover -5 pairs of stake pockets for 100 x 50 mm stakes in the outer frame of the loading area -Foldable extensions, approx. 230 mm per side -2 pairs of screwable RUD rings VLBG-4 M24 (LC 8,000 daN) -1 pair of steel ramps to bridge the hooks of the low bed -A painted layer of sand on the loading area as anti-slip protection -Speed sticker 80 km/h at the rear and on both sides -Dipper handle recess of the rear chassis closed at the rear with a plug-in plate -Four warning signs extendable by approx. 400 mm, approx. 423 x 423 mm Giodpfxehlz R So Amust -Radio remote control for the steering in addition to the cable remote control, with indicator lights on the receiver as Alignment control -Central lubrication system with 2 BEKAMAX (Pico) pumps with NLGI-2 normal grease -Load pressure gauge for determining axle loads -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot blasted, then the defined visible surfaces are hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminum 15%)

Condition: used, Universal Tool Milling Machine DECKEL Type FP 1 Machine No. 51265 Year of manufacture: approx. 1967 Travel paths X: 300 mm Y: 150 mm Z: 340 mm Table size 600 x 200 mm Spindle taper SK 40 - S20 x 2 Spindle speed 40–2000 rpm, 16 steps Motor power 1.0 and 1.6 kW, pole-changing Power supply 380 Volt, 50 Hz - Feed on X and Z axes - Spindle speed via 2 motor speeds and 8 gear steps - Quill movement at vertical milling head 60 mm - Swiveling, rotating, and tilting angle table - Coolant pump in machine base - Separate control cabinet Space requirements L x W x H 1100 x 1100 x 1600 mm Weight 690 kg In good condition Giedpfxeghtvao Amuot

Condition: new, weight max. 10 t workpiece diameter 100 - 3200 mm drum diameter 300 x 120 mm feed 100 - 1000 mm/min total power requirement 2 x 0,55 kW Gisdpfjf Ep Disx Amujt

Condition: excellent (used), Year of construction: 1955, Drilling capacity in steel St 37 Ø 65 mm Drilling capacity in cast iron Ø 75 mm Spindle mount MT 5 Throat 1250 mm Spindle stroke 400 mm Spindle speeds 22.4 – 1800 rpm Feed range 0.056 – 0.56 mm/rev Column diameter Ø 300 mm Motor power, 2-stage: 3.6 / 4.8 kW Clamping surface, base plate 1320 x 1000 mm Dimensions L x W x H (with motor!) 2250 x 1000 x 3100 mm Transport dimensions L x W x H (without motor!) 2250 x 1000 x 2800 mm Weight 5100 kg Accessories / Special features: • Cube table L x W x H 650 x 500 x 500 mm • Central clamping • Feed • Right-to-left travel • Motorized up and down travel • High speed range up to 1800 rpm • Coolant system • Lighting Siegfried Volz Machine Tools Rüschebrinkstr. 151-153 D - 44143 Dortmund - Wambel Giedpfx Amstwzk Dsuot

Condition: repair required (used), STANKO 2 A 554 The machine is in perfect working condition except for the clamping of the boom lifting device and is currently still in operation. Gedpetpu Tqjfx Amuoit The clamping would have to be reassembled and readjusted, all parts are present. For safety reasons, the boom is secured with a tensioning strap, the clamp for the lift is in clamped condition. Technical data: - Drilling capacity 60 mm - Projection 1600 mm - Drill spindle holder MK 5 - Drill spindle stroke 390 mm - Spindle speed, 20 steps 20 - 2000 rpm - Clockwise and counter-clockwise rotation - Feed rate, 12 steps 0.056 - 2.5 mm/rev - Drive 400 V / 12.8 kW - Clamping of the arm and drilling unit electromechanical - Distance machined machine bed - drilling quill - min. approx. 900 mm - max. approx. 1600 mm - usable machine bed with 4 T-slots 950 x 1700 mm - Coolant device - Cube table - Space requirement approx. W 2600 x H 3000 x D 1000 mm - Weight approx. 4500 kg

Condition: good (used), Clamping plate with T-slots and cross table, plate field, welding table, welding table, plate boring machine, T-slot plate, pallet changer -Quantity: a 2nd plate is still available ID21153 -Width: 1465 mm -Length: 4930 mm -Working height: 860 mm -Plate thickness: 35 mm Gjdpfx Amod Ehfljuoit -Plate height: 315 mm -Plate with: support ribs -Groove width: 51 mm -Groove spacing: 292 mm -Transport dimensions: 4930/1640/H860 mm -Weight: 6155 kg

Condition: used, Year of construction: 1990, sheet width 3050 mm plate thickness 12 mm distance between columns 3100 mm Gijdpeu Uu Smjfx Amust table height over floor 900 mm cutting angle adjustment 0,5 - 3 ° no. of strokes 6 - 13 Hub/min back stop - adjustable 1000 mm down holder 18 St oil volume 350 l total power requirement 22,5 kW weight of the machine ca. 8 t dimensions of machine L x W x H 3,96 x 2,10 x 2,22 m - with adjustment of cutting gap - Accessories: electr. back gauge, spare knives

Condition: new, table diameter 2000 mm table load 10000 Kg swivelling range 0 - 130 Grad turning speeds 0,02 - 0,2 U/min height adjustment 1450 - 2200 mm max. torque on the faceplate 20000 Nm engine output 1,5 / 2,0 kW welding current 1000 Ampere - Manual height adjustment. Gisdpfx Amjfv Ay Iouet - Self-locking gearbox, therefore hardly any pre and after-run at eccentric Load. - Electronic components from Schneider, Siemens and Delta. - Frequency-controlled, stepless speed of the turntable. - High stability due to the robust construction. - CE certificate. The D-HBE series comes as a standard version with a cable remote control and a footswitch.

Condition: new, table diameter 1200 mm table load 3 t swivelling range 0 - 135 Grad turning speeds 0,07- 0,7 U/min table height adjustment von 980 bis 1750 mm max. torque on the faceplate 4500 Nm welding current 700 Ampere Gsdpfofv Azasx Amueit including remote control and welding current transmission.