Center Lathe

TOS SN 630 S

Condition: used, Year of construction: 1984, turning diameter over cross slide: 1,600 mm, turning diameter: 2,000 mm, turning diameter over bed slide: 2,000 mm, turning length: 35,000 mm, workpiece weight (max.): 63,000 kg, Center Lathe SKODA - SUT 200 TD MACH-ID 9446 Manufacturer: SKODA Model: SUT 200 TD Year of manufacture: 1984 Tandem construction on one bed, with left and right headstocks Fpodpfx Anjynky Aedsi Faceplate double tailstock left and right Double carriage Steady rest included Roller rest included Operator panel with scales requires attention and replacement Motorized tailstock for each side (left and right) 3-bed way design Torque on chuck: 160,000 Nm Minimum turning diameter: Ø 315 mm Industries served: - Shipyards - Propeller shaft manufacturing - Hydraulic cylinder shafts - Camshafts - Defence & Aerospace - Rolls and shafts for steel mills - Crankshafts Specifications Metric / Imperial Turning length: 35,000 mm Swing over bed: Ø 2,000 mm Swing over carriage: Ø 1,600 mm Spindle power: 75 kW Bed width: 1,600 mm Quill diameter: Ø 400 mm Quill stroke: 250 mm Max spindle speed: 180 rpm Feed X-axis: 5,000 mm/min Feed Z-axis: 5,000 mm/min Workpiece weight: 63,000 kg Approximate dimensions: Length: 42,000 mm Width: 3,250 mm Height: 3,250 mm Weight: 158,000 kg Please note: The information on this page has been provided to the best of our knowledge and, where possible, obtained from the manufacturer. The information is given in good faith, but accuracy cannot be guaranteed. Accordingly, they do not constitute representations or contractual terms. We recommend verifying all important details.

Condition: used, greates pass round over bed 540 mm swing diameter over face slide 370 mm Fpodpfx Ajxnqzxjndei centre distance 3000 mm centre height 270 mm turning dia. in gap 815 mm bed width 344 mm spindle bore 88 mm spindle diameter in front bearing 133 mm spindle taper 11" D1 Camlock turning speed range 18-1400 U/min turning speeds 16 3-jaw chuck Röhm Ø 315 longitudinal feeds: 0,06-1,0 mm face feeds 0,03-0,5 mm metric threading 0,4-14 mm inch threading 2-72 G/1" thread - module 0,3-3,5 mm thread - DP 8-60 Pitch tailstock quill diameter 75 mm quill stroke 230 mm taper of tail spindle MK 5 slide valve travel 280 mm upper head travel 150 mm Overall size ca. 4700 x 1100 x 1400 mm weight ca. 3200 kg power capacity 9,4 kW Accessories: 2-axis digital display Fagor Röhm wedge bar chuck Ø 315 mm incl. hard base jaws and hard attachment jaws Multifix steel holder size C incl. 6 interchangeable cassettes Rotating center point Switchable lathe chuck guard 2 steady rests Chip guard Coolant device Work light Guideways in good condition without scratches, not worn Machine is in good overall condition with signs of wear commensurate with age. Includes operating instructions Translated with (free version)

Condition: used, Universal tool milling machine Brand: OPTIMUM Model: MT 100 Year of manufacture: 2018 – workshop tested Machine no.: J33021808035 Geometric acceptance with test report Accessories: - 3-axis digital display DPA 2000 Fodpfx Aew Rlvqendopi - Vertical milling head SK 40 with drawbar thread M 16 - Fixed table 1,120 x 260 mm (T-slot: 14 mm) - Machine lamp - Coolant system - Manual central lubrication - Operating manual Used as seen, without warranty The machine technically corresponds to the state of the art at the time of manufacture.

Condition: refurbished (used), WP Formprofi Fodotrwfujpfx Andjpi

Year of construction: 1998, condition: good (used), Make: UNION Type: Ti 1800 Year: 1998 Specifications Metric US Standard Table Length Fedpfxjkwcdbo Andepi 2000 mm Table Width 1800 mm Table load 16000 Movement V-axis 1250 mm Rotation B-Axis 360.000 ° Rotation speed B-Axis 1,35 Omw/min. Movement speed V-axis 4000 mm/min. Dimensions (Estimate) Length 3400 mm Width 2000 mm Height 920 mm Weight 6500 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, turning diameter over bed / mm turning diameter over slide rest / mm turning length / mm Conventional lathe with copying attachment and extensive accessories Turning diameter over cross slide: 240 mm Spindle bore: 52 mm Turning diameter: 360 mm Center height: 180 mm Turning length: 1,000 mm Overall length: 2,200 mm Overall width: 750 mm Overall height: 1,400 mm Maximum spindle speed: 1,750 rpm Min. spindle speed: 60 rpm Total weight: Fpjdpfx Ansv Rgzwedoi 1,800 kg All technical specifications are subject to change without notice. Deviations may occur depending on the year of manufacture, model, or condition of the machine. We assume no liability for the accuracy or completeness of this information.

Year of construction: 1993, condition: good (used), machine/vehicle number: 03.2370, Arthur Klink - internal broaching machine (WAG 748) machine type: internal vertical hydraulic broaching machine manufacturer: Arthur Klink type: RISZ 10 x 1000 built in: 1993 stroke: 1000mm pulling force: 10.000KG working stations: 3 PCs drive: hydraulic system Fsdpfx Ajcc D Ddsndopi equipment: coolant system, magnetic chip conveyer remark: machine under power in stock the machine has an automatic workpiece loading system for 2 workpieces, ideal useable for high production Optional accessories available on request: tools, workpiece holder Information about us: we are specialized for second hand broaching machine and still have anytime about 80 pcs of used broaching machines in our stock, vertical and horizontal machines from 3000kg up 63.000kg pulling force and from 1000mm stroke up to 3500mm stroke.

Condition: new, Year of construction: 2026, functionality: fully functional, Swing dia over bed 500 mm Swing dia over cross slide 270 mm Swing dia in bridge 700 mm Length of bridge 357 mm Center high 250 mm Center distance 1500 mm Width of bed 340 mm Max weigth of wpc. 300 kgs Spindle speed 22 – 2000 rpm Spindle hole D53 mm Spindle power 5,5 kW Weight ca.1950 kgs Fodpfsyt Iaqox Andopi Dimensions LxWxH = 3200 x 1100 x 1500 mm Accessories and features - 3 axis D.R.O. - Chuck protection - 3 jaws chuck D250 mm - 4 jaws chuck D300 mm - Tool holder protection - Stopper for long. slide - Steady rest - Travelling rest - Center - Reduction adapter for main spindle - Tailstock - Coolant unit - 4-fold toolholder - Machine lamp - Rapid speed on long, and cross slides - CE marking - Manuals

Condition: ready for operation (used), Year of construction: 1969, Centre height: 355 mm Centre distance: 3000 mm Max. swing diameter over bed/gap/cross slide: 715/790/520 mm Spindle bore: 86 mm Spindle mount according to DIN 55027: Size 11 Quill taper of tailstock: MK 5 21 spindle speeds: 5.6 - 560 rpm 42 feeds longitudinal/cross: 0.09 - 5.6/0.045 - 2.8 mm 22 Whitworth threads: 2 - 28 TPI 28 metric thread pitches: 1 - 14 mm 27 module thread pitches: 0.25 - 3.5 module 32 module threads: 4 - 56 module 32 diametral pitch threads: 8 - 112 DP Fsdpfsxpuu Eex Andepi Drive motor, pole-changeable: 380 V, 7/11 kW Weight approx.: 7 t Space requirement approx.: 6000 x 2300 mm

Condition: reconditioned (used), functionality: fully functional, LVD 4000 x 200T Press Brake Type PPBL 200/40 Fpjdpfxswtmi Es Andji Capacity 4000 x 200T Maximum stroke 150 mm Weight 13.5T With mobile blade rack