Lathe

Spinner SB-CNC

Condition: used, Year of construction: 2007, turning diameter over bed 0140 mm turning length 285 mm control 810D Siemens turning diameter over bed slide 140 mm swing dia. 300 mm spindle turning speed - stepless 0- 5000 U/min- rpm spindle bore 45 mm feeds 0- 12 m/min voltage 400 V connected load 14 KW face slide travel 250 mm longitudinal travel 285 mm dimensions of the machine ca. 2,7 x 1 x 1,6 m taper diameter VDI 20 mm main drive motor 10,2 kW Kedpfxox Hpyys Aaloww weight of the machine ca. 1,7 t Machine is without live tooling and without tailstock.

Year of construction: 2002, condition: reconditioned (used), Beam cutting, drilling and marking line DISC SAW Brand: KALTENBACH Model: HDM 1431 / T13 / SP-CNC Year 2002 Serial number: 122.400 Weight without accessories: 10,980kh - Disc saw with downward cut. - Geared saw unit, drive system and saw blade on wear-resistant swivel bearing. - Heavy saw gear with pinions in oil bath, with inclined teeth, hardened and sharp. - Hydraulic advancement of the saw blade, adjustable according to the table, very fast recoil. - Hydraulic horizontal clamping device. Rear clamping jaw with long-stroke clamping cylinder and automatic recoil limitation. - Vertical clamping block with self-adjusting push plate. - Oblique cutting device to adjust the angle from 45° to the left to 35° to the right. - Material sensor to automatically switch from rapid advance to work advance. - Hydraulically elevating feed roller for optimum material transport on the saw table. - Economical lubrication by means of a micro-dosing installation, especially suitable for sawing profiles. - Chip collector installed on the machine bench. Specs: - Cutting disc housing: 100x4x30x250mm - Cutting disc diameter: 1,430mm - Cutting width: 9.5mm - Cutting speed: 10 to 20m/min. - Saw advance speed: 0-400mm/min. - Fast reverse speed: 2000mm/min. - Total power: 25KW - Working height: 640mm Cutting capacities: 90º cut - Angle steel: 250mm - Steel in U: 400mm - Double T-beam: 600mm - Wide flanged beam: 1008x302mm - Special wing beams: 1000x450mm Cut to degrees: IPBv beam - 75º: 1008x302mm - 60º: 910x302mm - 45º: 716x304mm - 40º: 716x304mm - 35º: 478X307mm IPBs beam - 75º: 1008x402mm - 45º: 524x357mm IPE beam - 45º: 600x220mm DRILLING UNIT Brand: Kaltenbach Model: KDX1215 Serial number: 122.401 Kwedpohzbipefx Aaljw Work capabilities: - Angular steel (minimum - maximum): 80x65x10mm - 250x250x28mm - Steel in U (minimum - maximum): 80x45mm - 400x110mm - Double T beam (minimum - maximum): 80x46mm - 600x220mm - Wide flanged beam (minimum - maximum): 100x100mm - 1,008x302mm - Extra wide wings beam: 1,200x500mm Drilling units: 3 - Vertical (Y axis) 1 pc. - Horizontal (Z and W axes) 2ud. Drilling diameters: 8 - 40mm RPM: 150 - 1100 Fast forward - Fast reverse: 3,850mm/min. - 8,000mm/min. Drilling spindle feed rate: 0-500mm/min. Fast spindle positioning tool: 15,000mm/min. Automatic tool changer: 5 u. in each drilling unit. 3x5 u. = 15 total Total power: 45KW MARKING UNIT FEEDING: 26 METERS OF ENTRY WITH BEAM FEEDER + 6 SIDE ARMS FOR BEAM ENTRY IN PARALLEL TO THE ROLLER TRACKS 30 METERS OF ROLLER TRACKS WITH OUTPUT + 6 SIDE ARMS 4 SIDE ARM FOR SMALL PIECES THE GREAT MAJORITY OF ROLLERS ARE MOTORIZED It occupies approximately 60 linear meters between input and output power. *Request machine installation plans.

Year of construction: 2004, condition: ready for operation (used), Technical data: working area: turning diameter max.: 300mm, travel X/Y: max. 200mm/350mm, chuck diameter: 125mm, distance between centers: approx. 300mm, speed range: 40-5000rpm, spindle nose: A2-4, tool holder: VDI16, CNC control: FANUC Series 18i-TB, installation dimensions X/Y/Z: approx. 1800mm/1300mm/1700mm, machine weight: approx. 2200kg. Inspection is possible by arrangement. Kodoylbufspfx Aaleww

Year of construction: 2011, condition: ready for operation (used), Horizontal machining center with 5-axis Fanuc CNC, tilting table with 120° and continuous B-axis. Kwjdpsku A A Hjfx Aalsw Pallet magazine with 10 stations, automatic tool changer with 199 stations. Accessories included with the machine: Chip conveyor, high pressure coolant system through the spindle line with separate tank and paper filter.

Condition: good (used), CHP natural gas, 2 pieces Onsite Energy ME3042L3 Bj 2009, Engine: MTU E3042L9 year 2016 23.000h operating hours, Generator: LSA C47.2M7 C6/4 400V 50Hz 465KVA Absorber chiller: Carrier 16LJ-A24E 689KW cooling capacity Emergency cooler: Güntner GFH 090.2B/2x2-M Kwodpfxoun I N He Aaljw 12m chimney, silencer, pumps, actuators, dampers, valves, gas control system Higher-level control: synchronization, load management, island operation, grid support, ec , load control cabinets 714KWe, thermal 1058KW, cooling 689KW

Condition: good (used), Studer S30-12 cylindrical grinding machine TECHNICAL DATA Main dimensions Center height: 125 mm Center width: 400 / 700 / 1025 mm Largest longitudinal slide path: 400 / 700 / 1000 mm Ksdpevca Izjfx Aaleww Longitudinal slide Table speed: 50 - 5000 mm/min Reversing delay: 0-6 s Smallest automatic travel: 1.5 mm Max. stroke: 400 / 700 / 1020 mm Max. Table inclination: 12 / 30 / 78° Cross slide Swivel range: +- 45° Quick adjustment: 40 mm Feed path with handwheel: 20 mm Largest plunge depth: 1.7 mm Sanding headstock Grinding wheel diameter x width x bore: 450 x 80 x 203 mm Speed: 1340 / 1500 1625 / 1800 / 2000 / 2200 rpm Coarse adjustment: 210 mm Workpiece headstock Swivel range: 0 - 90 Speed range: 30 - 675 rpm Mounting cone: Morse 5 Collets: W25 Tailstock Mounting cone: Morse 3 Adjustment travel of the center: 30 mm Total power requirement: 5 / 8.25 kW No liability is assumed for the correctness, completeness and up-to-dateness of the information.

Condition: excellent (used), Year of construction: 2008, functionality: fully functional, machine/vehicle number: 16380, CNC automatic lathe CITIZEN CINCOM L-20 VIII with Fedek STM-326 bar feeder, year 2008. Machine is fully controlled by Citizen. Supplied with geometric protocol. Kwodpfjw T Stzjx Aalew

Condition: used, Year of construction: 2003, turning diameter max. 420 mm turning length 1090 mm control FANUC Serie 18i-TB turning spindle Durchlass 108 mm 250 / 315 Kedpoucgyljfx Aaljww turning speed range 0-3750 U/min Feed speed 18/24 m/min. workpiece 12 quill stroke 100 mm diameter of quill 110 mm taper MK 4 number of driven tools 12 mm turning speeds 3000 U/min 22 nm coolant tank 140 l total power requirement 22/18,5 kW weight of the machine ca. 6500 KG

Condition: used, Year of construction: 1996, Technical details: weight of the machine ca.: 1750 kg Kedpfxjvpt Eyj Aalsww sawing motor: 2,2 kW total power requirement: 5 kW cutting speed: 17 - 90 m/min cutting diameter: 320 mm cutting range max.: 320 x 320 mm saw band length: 4.930 x 34 x 1,1 mm feed length: max 9x 600 mm dimensions of the machine ca.: 2,6 x 2,4 x 1,40 m Bandsaw automatic, straight cut, min. cutting diameter 10mm, min. cutting length 6mm, min. offcut 15mm (automatic 80mm), max. weight of material 400kg/m, coolant box 60l, pump 16l/min, clamping pressure 20-60bar, dimensions: chipconveyor 2.400x 950mm roller track 2.200 x 950mm, 5pcs. saws (new) 4.930 x 34 x 1,1mm operating manual, *

Condition: excellent (used), Year of construction: 1991, functionality: fully functional, Machine still under power and production can be seen at any time. Technical Data – PE 150 This hobbing machine with automatic workpiece change system is designed for series production of workpieces, for which the corresponding drawings have been received. Our specialists for automatic workpiece changing systems will gladly assist you if you wish to convert the machine for milling different workpieces. Hob Cutter: Max. permitted cutter outside diameter: 130 mm Max. length (depending on cutter arbor diameter): 220 mm Slide Travel: Kwodpfx Aasu N E Rroljw Radial (X-axis): 150 mm Tangential (Y-axis): 170 mm Axial (Z-axis): 200 mm Max. Swivel Angle of Milling Head: In +A direction: 30° In -A direction: 45° Workpiece Table: Outer diameter: 160 mm Bore diameter: 63 mm Overall Dimensions of the Machine: Length: 5,820 mm Width: 4,047 mm Height: 2,810 mm Approximate Weight of Machine: 8,000 kg Speeds: Feeds: Axes X, Y, and Z: 1 to 3,000 mm/min Rapid Traverses: Axes X, Y, and Z: 3,000 mm/min Spindle Speeds: Tool (S-spindle): 150 to 600 rpm Workpiece table (C-axis): 1 to 125 rpm Electrical Equipment: Operating voltage: 400 V Supply voltage: 230 V Control voltage: 24 V Frequency: 50 Hz Connected load of the machine: 48.5 kVA Cable cross-section: 25 mm² Fusing: 100 A