Cavity Sinking EDM - Machine

SIEGBURG NS 201

Year of construction: 2003, condition: ready for operation (used), A total of seven injection molding machines Arburg are available. 1) Arburg 320C 600-250, year of manufacture: 2001, operating hours: 83365h, clamping force: 600kN, screw diameter: 30mm, shot weight: 97g, max. injection pressure: 2470bar, injection volume: 106cm³, centering: 125mm/125mm, max. opening stroke: 550mm, plate distance: 550mm, plate dimensions X/Y: 446mm/446mm, tie bar distance: 320mm/320mm, core pulls: 2, temperature control units: 6, machine dimensions X/Y: approx. 4000mm/2300mm. Including Multilift handling unit. 2) Arburg 420C 1000-250, year of manufacture: 2001, operating hours: 90769h, clamping force: 1000kN, screw diameter: 30mm, shot weight: 97g, max. injection pressure: 2470bar, injection volume: 106cm³, centering: 125mm/125mm, max. opening stroke: 750mm, plate distance: 750mm, plate dimensions X/Y: 570mm/570mm, tie bar distance: 420mm/420mm, core pulls: 2, machine dimensions X/Y: approx. 4700mm/2350mm. Including Multilift handling unit. 3) Arburg 270C 300-100, year of manufacture: 1999, operating hours: 78784h, clamping force: 300kN, screw diameter: 20mm, shot weight: 28g, max. injection pressure: 2500bar, injection volume: 31cm³, centering: 110mm/110mm, max. opening stroke: 550mm, plate distance: 550mm, plate dimensions X/Y: 446mm/446mm, tie bar distance: 270mm/270mm, core pulls: 1, temperature control units: 6. Including Geiger handling unit. 4) Arburg 320C 300-100, year of manufacture: 2000, operating hours: 78784h, clamping force: 300kN, screw diameter: 20mm, shot weight: 28g, max. injection pressure: 2500bar, injection volume: 31cm³, centering: 125mm/110mm, max. opening stroke: 350mm, plate distance: 350mm, plate dimensions X/Y: 446mm/446mm, tie bar distance: 320mm/320mm, core pulls: 1, temperature control units: 6. 5) Arburg 220C 250-60, year of manufacture: 2001, operating hours: 86595h, clamping force: 250kN, screw diameter: 22mm, shot weight: 27g, max. injection pressure: 2340bar, injection volume: 30cm³, centering: 110mm/110mm, max. opening stroke: 425mm, plate distance: 425mm, plate dimensions X/Y: 400mm/400mm, tie bar distance: 221mm/221mm, core pulls: 1, temperature control units: 6. 6) Arburg 270C 300-100, year of manufacture: 2007, operating hours: 59885h, clamping force: 300kN, screw diameter: 20mm, shot weight: 28g, max. injection pressure: 2500bar, injection volume: 31cm³, centering: 110mm/110mm, max. opening stroke: 550mm, plate distance: 550mm, plate dimensions X/Y: 446mm/446mm, tie bar distance: 270mm/270mm, core pulls: 2, temperature control units: 6, machine dimensions X/Y: approx. 3750mm/2400mm. Including Multilift handling unit. 7) Arburg 220S 250-60, year of manufacture: 2001, operating hours: 57504h, clamping force: 250kN, screw diameter: 18mm/22mm, shot weight: 18g/27g, max. injection pressure: 2500bar/2340bar, injection volume: 20cm³/30cm³, centering: 110mm/110mm, max. opening stroke: 425mm, plate distance: 425mm, plate dimensions X/Y: 400mm/400mm, tie bar distance: 221mm/221mm, core pulls: 1, temperature control units: 6, machine dimensions X/Y: approx. 3300mm/1100mm. Documentation available. An on-site inspection is possible. Ndedpfx Ajtyyn Hea Ejf

Year of construction: 1996, operating hours: 24,222 h, condition: good (used), This Dr. Boy injection moulding machine is in machine storage at Plastima Used Machinery. The machine is from 1996 and has relatively few working hours for its age. - Brand: Dr Boy - Model: 80M - Year of construction: 1996 - Screw diameter: 42mm Ndjdpfopwh Akjx Aa Esf - Shot volume: 200 cm³ - Clamping force: 80T - Working hours: 24,222

Year of construction: 1988, condition: used, weight max. in kg 6000 kg fork length 1900 mm 89% serial number GEF 2240 height of stroke 3300 mm Nedpfx Aaerxxbto Eedf weight of the machine ca. 9650 t

Condition: used, Technical details: measuring range Y-axis: Höhe: 0 - 600 mm interface: RS232 weight: 24 kg power consumption: 43 Watt Floor Space WxD: 0,237 x 0,448 x H: 1,013 m Ndjdpfx Aoxcvqnsa Eof High-precision height measuring device Linear Heigth with a glass scale for high accuracy. With LCD display and keypad. This is a table-top device. The main unit can be easily moved in a semi-floating position on a measuring plate using a push-button (float switch). The carriage can perform both automatic and manual movements. incl. eccentric probe at the tip with a ball Ø 4.5 mm Data output RS-232C interface the measuring carriage is guided by roller bearings, motor-driven and/or manual Measuring system - glass measuring system (incident light method) Compressed air supply via built-in compressor Operation via control panel (with graphic display) with granite plate without table *

Condition: used, machine/vehicle number: 11666, Rotor diameter: 280 mm Rotor width: 300 mm 3 blade rotors Ndsdpfxsghgq Nj Aa Ejf 2 rows of stator blades Inlet cross-section approx. 300 x 280 mm Drive motor 11 kW With noise protection box, noise protection hopper, and exhaust fan

Condition: new, LIFTING EQUIPMENT FROM 5 - 10t WEIGHT TRANSPORT TROLLEYS FROM 5 - 30t WEIGHT A LOT OF VARIETY NEW IN STOCK Ndsdpfji Akpdex Aa Eef

Condition: good (used), Year of construction: 2008, Parts shown by hand not included. Ndodpouc Tpgsfx Aa Esf 12.000 rpm X 610 mm Y 420 mm Z 450 mm

Condition: ready for operation (used), Forklift truck Manufacturer: Jumbo Type: J60 DC12 Diesel Year of manufacture 1994 Payload: 6,000 kg Own weight: 9,260 kg Lifting height: 4300 mm approx. 25,000 operating hours Sold due to switching to wheel loader All service and lubrication intervals verifiably completed according to the inspection book! All filters (hydraulic, fuel, converter, air) replaced annually. Engine oil filter including oil every 250 operating hours. Only B0 was used as diesel fuel. (no B7) immediately available - fully functional Location: Austria, near St. Pölten Nsdpfsvtwuaox Aa Eedf

Condition: used, Year of construction: 2005, functionality: fully functional, travel distance Z-axis: 1,219 mm, rotational speed (max.): 2,000 rpm, travel distance cross slide: 203 mm, Flatbed Lathe Manufacturer: Haas Type: TL-2 S/N: XXXXX Year of Manufacture: 08-2005 On-time hours: n/a Control: Haas CNC Technical Parameters: ----- - 4-way tool post with Parat quick change system - Z travel: 1,219 mm - X travel: 203 mm - Swing over bed: 406 mm - Swing over slide: 282 mm - Spindle bore: 76 mm - Spindle speeds: 10 - 2,000 rpm - Coolant system - Tailstock / MT 4 - Weight: 2,100 kg Accessories: ----- Ndsdpfx Aaswftdms Ejf - 3 Parat cartridges - 3-jaw chuck - Documentation

Condition: excellent (used), Year of construction: 2007, functionality: fully functional, travel distance X-axis: 250 mm, travel distance Y-axis: 200 mm, travel distance Z-axis: 300 mm, rapid traverse X-axis: 30 m/min, rapid traverse Y-axis: 30 m/min, rapid traverse Z-axis: 30 m/min, controller manufacturer: FANUC, workpiece diameter (max.): 32 mm, rotational speed (min.): 500 rpm, rotational speed (max.): 30,000 rpm, overall weight: 1,700 kg, spindle nose: HSK-E40, number of slots in tool magazine: 48, tool length: 95 mm, tool diameter: 63 mm, input voltage: 400 V, type of input current: three-phase, Equipment: documentation/manual, WILLEMIN MACODEL W408 MT TECHNICAL CHARACTERISTICS : Year : 2007 CNC control : FANUC 16i-MB Number of axes : 5 Stroke X axis : 250 [mm] Stroke Y axis : 200 [mm] Stroke Z axis : 300 [mm] Traversing feeds X, Y and Z axes : 30000 [mm/min] Max. bar diameter in turning spindle : 32 [mm] Main spindle max. speed : 6000 [rpm] Main spindle max. power : 3.7 [kW] Angular C axis stroke : 360 [°] B axis swivelling stroke : 115 [°] Spindle type : HSK-E40 Min. spindle speed : 500 [rpm] Max. spindle speed : 30000 [rpm] Spindle power : 10 [kW] Tool changer magazin number of stations : 48 Max. tool lenght : 95 [mm] Ndjdowu Ruhspfx Aa Eef Max. tool diameter : 63 [mm] Lubrication tank capacity : 80 [l] Collant pump flow rate : 40 [l/min] Rated current : 25 [A] Supply voltage : 400 [V] Weight : 1700 [Kg] EQUIPMENT INCLUDED : x1 0-90° pivoting backworking unit (6th side machining) x1 backworking vice x1 RENISHAW TS27R tool probe x1 RENISHAW NC4 TX laser system for tool setting and tool breakage detection x68 type F35 turning collets x9 HSK-40E milling/turning attachments x1 IEMCA BOSS 332 E bar feeder x1 spindle chiller x1 cutting fluid chiller x1 ELBARON mist extractor x1 3-colour status lamp x1 CO2 automatic fire extinguishing system (to be checked by the purchaser with a competent body) x1 set of technical manuals Price on request, loading on truck included. Possibility of shipping Worldwide. The information on this page has been obtained by the best of our ability. Therefore, its accuracy can not be guaranteed. HERMLE , DMU , monoblock , variaxis , chiron