Profile bending machine

Sahindler - Scantool PV 60 NC

Condition: used, Thread Rolling Machine, Cold Rolling Machine, Thread Rolling Machine, Profile Rolling Machine Manufacturer: PEE-WEE Model: UPW 24 Serial No.: P07 Year of manufacture: 2007 Maximum rolling force: 24 tons Maximum tool diameter: 270 mm Roll spindle diameter: 69.85 mm Tool bore diameter: 70 mm (nominal diameter) Maximum tool/reception length: 180 mm Maximum workpiece diameter: 50 mm Fpsdpouz If Njfx Aikop Hydraulic motor power: 3 kW Roll drive motor power: approx. 5.5 kW Electrical connection: 400 Volt, 50 Hz, 10 kW - Pivotable roll spindle for through-feed thread rolling - Roll spindle speed adjustable in 4 steps via gearbox shift - Hydraulic unit integrated in the machine base - Operating manual with electrical schematic Space requirements (L x W x H): 2,000 x 1,450 x 1,900 mm Weight: approx. 3 tons Very good condition Plunge Rolling: The thread rolling tools, having the same pitch as the workpiece, form the thread by penetrating the workpiece up to the nominal diameter. The maximum thread length is limited to the width of the rolling dies. Through-feed Rolling: Used when the thread length is greater than the width of the rolling dies. Through-feed tools are divided into three sections – entry, calibration, and exit. Knurling rolls have no pitch and are swiveled at the lead angle corresponding to that of the profile to be rolled. Lead angle rolls differ from knurling rolls by having a pitch in the profile. The sum of the lead angle and swivel angle results in the effective lead angle in the workpiece.

Condition: good (used), Year of construction: 2011, operating hours: 19,000 h, functionality: fully functional, travel distance X-axis: 880 mm, travel distance Y-axis: 630 mm, travel distance Z-axis: 635 mm, spindle speed (max.): 12,000 rpm, operating hours of spindle: 19,000 h, spindle nose: HSK 63, number of slots in tool magazine: 32, Equipment: chip conveyor, documentation/manual, The machine will be available starting October 2026! Fedpfxszx Ur Nj Aikspp

Condition: used, centre distance 2.500 mm centre height 250 mm grinding wheel diameter 600 mm Total travel of the grinding support 320 mm spindle speeds 50 - 450 mm tool adaptor MK5 tail stock MK Cylindrical Grinding Machine | NAXOS-UNION - W-500 the cylindrical grinding machine was overhauled in 2017 by KPS-Schleiftechnik (RETROFIT – see order confirmation). The machine is in a well-maintained condition. Please refer to further technical details in the attachement of the offer. - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Fpsdex Avtcopfx Aikep #Tags: W-500-2500 | W500 | W 500 | W 500 2500

Year of construction: 2005, condition: ready for operation (used), - USED - 6-AXIS SLIDING HEADSTOCK LATHE WITH BAR FEEDER MAX TURNING LENGTH: 320 mm MAX TURNING DIAMETER: 32 mm SPINDLE: 200-8000 rpm; 3,7 - 7,5 kW COUNTER SPINDLE: 200-7000 rpm; 1,5 - 2,7 kW X1-AXIS TRAVEL: 108 mm X2-AXIS TRAVEL: 228 mm Y1-AXIS TRAVEL: 275 mm Z1-AXIS TRAVEL: 325 mm Z2-AXIS TRAVEL: 130 mm Z3-AXIS TRAVEL: 410 mm Fpedpfjvthv Isx Aikjp RAPID FEEDS X-Y-Z: 20 m/min DRIVEN TURRET HEAD: 8 POS; 200 - 5000 rpm CONTROL UNIT: CINCOM SYSTEM M6D BAR FEEDER: IEMCA Mod. BOSS 332 EVOLUTION WEIGHT: 2850 Kg ACCESSORIES: PARTS CATCHER

Condition: good (used), functionality: fully functional, Year of construction: 2007, machine/vehicle number: CA90H2 PIPE BENDING ROLL, shaft diameter: 90 mm, roller diameter: 260 mm, rotational speed (min.): 8 rpm, rotational speed (max.): 8 rpm, overall weight: 1,000 kg, total length: 1,260 mm, total width: 1,000 mm, total height: 1,260 mm, power: 3.68 kW (5.00 HP), input voltage: 380 V, type of input current: three-phase, operating speed: 8 mm/s, roll diameter: 260 mm, Equipment: documentation/manual, emergency stop, PROFILE BENDING ROLL SHAFTS OUTPUT 90 MM - PIPE BENDING ROLL MARGI CA90H2 YEAR 2007 SHATS OUTPUT SIZE 90 MM Fodpowkrr Tjfx Aikepp SET OF UNIVERSAL ROLLERS SIZE 260 MM LATERAL CORRECTOR ROLLERS LEFT/RIGHT SIDE SCREW ADJUST 4 SET OF ROLLERS FOR TUBE BENDING MM 61 - 78 – 90 – 116- CONSOLE ELECTRIC MOVABLE ON WHEELS ALL THE CONTROLS CENTRALIZED DIGITAL POSITION READOUT OF BENDING ROLLS UPPER ROLL DRIVEN MOTORIZED ELECTRIC POWERED WITH GEAR UNIT SIDE ROLLERS HYDRAULIC ADJUSTMENT POWERED INDEPENDENT WITH PISTON MACHINE REVERSIBLE CAN WORK WITH SHAFTS VERTICAL/HORIZONTAL. SAFETY AND EMERGENCY STOP EQUIPMENT INSTALLED WITH THE MACHINE MANUALS AND SCHEMATICS IN ORIGINAL ALONG WITH THE MACHINE WEIGHT 1000 KG DIMENSION 1260 X 1000 X H 1260 MM

Condition: repair required (used), grinding diameter: 1,295 mm, grinding length: 4,276 mm, Looking for a high-precision cylindrical grinder for large workpieces? We have a Farrel 50 x 14 CNC Cylindrical Grinder available! This machine is ideal for industries requiring precise concave and convex grinding, ensuring superior accuracy and efficiency. Key Features: Concave grinding possible Covex grinding possible NUM 760 CNC Control Fixed steady rest 2 x  Fpsdsv Dia Aepfx Aikjp Stones and Flanches included Centre height: 647mm Grinding Ø: 1295mm Grinding length: 4267mm Grinding stone dimensions:914 x 152 mmmm Grinding stone speeds: 400 - 1200Rpm Cooling system: Yes Length: 8500mm Width: 4500mm Height: 3200mm Weight: 78000kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: good (used), Year of construction: 2003, functionality: fully functional, machine/vehicle number: 675149, center height: 175 mm, grinding length: 8,000 mm, center width: 1,000 mm, grinding wheel diameter: 450 mm, total width: 1,700 mm, total length: 3,000 mm, grinding diameter: 349 mm, workpiece weight between centers: 100 g, distance between centers: 1,000 mm, type of input current: three-phase, feed length X-axis: 320 mm, feed length Z-axis: 1,000 mm, overall weight: 3,500 kg, year of last overhaul: 2022, input frequency: 50 Hz, rapid traverse Y-axis: 12 m/min, rapid traverse Z-axis: 6 m/min, input voltage: 400 V, workpiece spindle speed (max.): 800 rpm, Dear Sir or Madam, The sale of this machine is strictly limited to end users located within the European Union (EU). Under no circumstances will the machine be sold to dealers, resellers, or intermediaries. Sales are exclusively intended for end users, manufacturing companies, and companies that will directly operate the machine. Control System Control system manufacturer: FANUC Control system type: GE FANUC Series 21i-T Work Area Center height: 175 mm Distance between centers: 1,000 mm Grinding length: approx. 800 mm Max. workpiece diameter: approx. 349 mm Electrical data according to your specifications Connection voltage: 3400 V Operating voltage: 3400 V Frequency: 50 Hz Control voltage: 24 V Rated current: 20.5 A Main fuse: 25T A Fedpfxj Ahv T Hs Aikjpp Grinding technology according to the documentation Grinding spindle power: 5.0 kW Grinding spindle speed: 800–1,900 rpm Grinding wheels: depending on the design, up to approx. Ø 450 mm X-axis resolution: up to 0.1 µm Workpiece spindle speed range: approx. 8–800 rpm Automatic indexing: provided for the UR version Further technical data from the manufacturer's documentation Max. ambient temperature: 40 °C Max. humidity: 75 % Sound pressure level: approx. 70 dB(A) Machine weight: approx. 3,500 kg Sale without tools and without additional accessories. The machine is sold exclusively with the described standard configuration. Inspection possible by appointment. Sale ex works Syntegon. Loading and transport are the responsibility of the buyer. Sales/transfer conditions: • Sale exclusively to end users/manufacturing companies (no resale to dealers) – corresponding company profile required. • Disassembly, removal, and transport are the responsibility of the buyer and at the buyer's risk. • The buyer is responsible for providing personnel, tools, and transport equipment. Personnel may only work with appropriate personal protective equipment, and only trained personnel may be used.

Condition: used, grinding diameter / mm grinding length 4000 mm Fpjdpfxozgipxj Aiksp swing diameter / mm

Condition: new, Year of construction: 2024, shaft diameter: 80 mm, Profile bending machine AHB 100 - with universal rollers - Three roller drive - Digital display left and right bending axis - Hydraulic lateral rectifier - Hydraulic drive of the bending rollers - Vertical and horizontal operation - built according to CE standards - Bending capacity flat bars max. 12 x 20 mm - Flat bent 200 x 40 mm - U profile inside and outside 180 mm - Angle profile web outside 100x100 mm - Angle profile web inside 90x90 mm - Solid material round 75 mm - INP 140 - Shaft diameter 100 mm - Roller diameter 315 mm - Bending speed 5 m/min. - Motor power 11 KW - Weight 2600 kg Fsdpfjvaw Elox Aikspp - module max Wcm3 -400 Volt 50 Hz. 3 ph. -1950x1600x2100 mm

Condition: used, TECHNICAL DETAILS Fpsdpfx Aijzfqzaokjp - Distance between centers : 1000 [mm] - center height : 175 [mm] - Table orientation : 9 [°] GRINDING WHEEL HOLDER HEADSTOCK - Left grinding wheels dimensions : 400 x 50 x 127 [mm] - Right grinding wheels dimensions : 225 x 20 x 76,2 [mm] - Power : 3 [kW] - Spindle speeds : 1500 / 1700 / 2200 [rpm] - Orientation of grinding wheel holder headstock : 270 [°] - Boring for internal spindle : 90 [mm] PART-HOLDER HEADSTOCK - Orientation of part holder headstock : 360 [°] - Spindle speeds : 20 - 400 [rpm] - Spindle internal cone : Morse 5 - Power : 0.9 [kW] TAILSTOCK - Internal cone : Morse 3 - Quill stroke : 30 [mm] POWER SUPPLY - Supply voltage : 380 [V] WEIGHT & DIMENSIONS - Machine floor space : 2860 x 1680 [mm] - Machine height : 1670 [mm] - Machine weight : 2500 [kg] EQUIPMENT - Automatic cycle work (rough part, finishing and reverse) - Kelco 5 display - Coolant tank * with paper filtering unit - 1 internal grinding spindle : 5400 [rpm] - Chuck 4 jaws - 1 three-key steady rest - Set of wheels