Paint/spray booth

Reinox 219x235

Condition: new, Year of construction: 2026, functionality: fully functional, type of input current: three-phase, Paint/spray wall dimensions without fan and control Panel! Extraction surface - dimensions (mm): 2190w)x2350(h) Overall dimension(mm): 2295(w)x2295(h)x810(d) Technical data: - Fan power 2.2kW (ATEX) - Fan suction capacity: 12000 m³/h (max 1100Pa) - Connection voltage: 400V - Frequency converter for smooth regulation of the fan - Three-stage air filtration - Intended for explosive environments - EX - Complete technical documentation - CE Documentation Bedpeia Ta Aofx Acvelf - Warranty Possibility to order machines in various individual configurations and dimensions! Do not hesitate to contact us.

Year of construction: 2018, condition: new, Freeze dryer completly new. Pilot plant. Capacity:1 kg / 8hrs Effective Area :0.15 m2 Wet Input per 8 hr: 1 Kg Dry Output per 8 hr: 0,2 Kg Temp Range Drying: 30 ºC - 100 ºC Water Removal Capacity: 0,8 Kg Ultimate Condenser Temp: -40 ºC Bedjfn Iudepfx Acvslf Defrosting Method: Natural Total Connected Load : 1Ph/15 Amp Connection Average Connected Load: 1Ph/15 Amp Connection Plant dimensions: 1,1m*0,7m*1,5m 1. Freeze Drying Capacity: Wet input 1 kg. per shift. On a higher side, each shift shall be of 8 to 8.5 Hrs. The wet input can either be biological cultures, enzymes, polymers, extracts, sprouts, vegetables, fruits, nutraceuticals, herbs, spices, sea foods, instant curries/gravies etc. of minimum 15% solids. 2. Residual moisture: Final moisture content on the product shall be less than 4%. 3. Compressed air: Maximum pressure 5Kg/Sq.cm. Flow rate 3 cubic Meter/Hr. Material: Stainless steel 304 Flow rate vacuum pump: 13 m3/h

Condition: good (used), Make: OMERA Type: R4 / 12-2 Year: 1976 Table length : 1900 Table width : 1000 Steady arm throath HOR : 670 Steady arm throath VER: 940 Stroke cylinder : 350 Column diameter : 200 Specifications Metric US Standard There are no specifications for this machine (yet). Dimensions (Estimate) Length 3000 mm Width 2200 mm Height 2500 mm Weight 2800 kg Bjdpskvnumjfx Acvslf Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: new, Step By Step Wet Painting Systems Elboy Industrial Solutions designs and manufactures full range of paint shops for your product. With ELBOY, you can navigate through your facility with virtual reality in the design phase, enabling you to make the desired changes in the design phase and not to encounter the surprise results. It provides designing and manufacturing services for your application by paying special attention to environmental pollution and work safety issues for the processes of Sandblasting, Putty, Washing, Undercoat and Finishing Coat for all sizes of products. Step by Step are systems with overhead conveyor or floor conveyors which can be designed for all sizes of product. Booths of Sandblasting, Chemical Washing, Pre-coat, Drying, Putty , Top Coat and Baking can be integrated into the system. In order to respectively carry out the processes determined by the system step by step, the automatic doors are opened at the end of the time period and the product automatically proceeds to the next process line. These fully automated systems are controlled via a 15” touch screen and provide various reporting methods such as main computer monitoring, product reporting and score reporting upon the demand and provide remote control. These are the paint shops where your product is designed and manufactured by our engineers in line with your capacity, use area and other demands. Blodpfx Acjdy Dw Ajvof Maximum efficiency is aimed to be provided with minimum staff and the least space usage at electrostatic powder coating or wet paint, sandblasting, varnishing, coating, washing and similar system requirements.

Condition: used, Year of construction: 1993, machine/vehicle number: 931200665, Verpackungssystem - Wrapping & Shrinking Machines BVM SM4012 K-SC4030SYear 1993 - Serial-No. 931200665 Full automatic packaging SM 4012K Einlaufbreite max. 420mm / Infeed width max. 420mm Shrink tunnel SC4030S Format (Breite x Höhe) / Size (width x high) 450mm x 330mm Blsdpfxoh Ax Hfj Acvsf 5m Chain gripper feeder Delivery band GUK Feeder for single sheets Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Condition: new, capacity 90 degrees: round 305 mm capacity 90 degrees: square 260 mm 350x200 saw band length 3375x27x0,9 mm band speed 37 + 74 m/min table height 940 mm total power requirement 1,5/1,8 kW weight of the machine ca. 0,65 t dimensions of the machine ca. 1,5 x 1,75 x 1,9 m SPECIAL PRICE!!! Double miter metal band saw, hydraulic semi-automatic GBS 305 HA-I Easy - Miter cuts up to 60° left and 45° right - Material height button Bsdpjd Iipxefx Acvjlf - Ball bearing turntable - hydraulic Vice, laterally displaceable - Massive, large material support - Automatic cooling

Condition: new, functionality: fully functional, Comparable with Durma, Baykal, Ermaksan, etc. Bending length 3020 mm Pressing force 320 t (also available in many other configurations!) Approach speed 140 mm/s Bending speed max. 10 mm/s Return speed 130 mm/s Y-axis stroke 400 mm Open height 650 mm Throat depth 450 mm Clear gap between frames 2555 mm Machine length 3785 mm Machine width 2290 mm Width without support arms 1740 mm Overall height 3100 mm Table height 920 mm Motor power 22 kW Bodjuf Nr Aepfx Acvjlf Oil tank capacity 300 l Machine weight 14,450 kg (Specifications may vary depending on equipment) Standard equipment: 3 CNC axes (Y1, Y2, X) Press beam double-guided, stable and precise Robust double-guided backgauge Backgauge fingers double-guided on linear rails Movable front arms with height adjustment Side and rear safety guards 60mm lower die adapter rail Manual upper tool clamping system (Promecam system) Foot switch with emergency stop 380 V, 50-60 Hz, 3 phase LED lighting Additional equipment: Delem DA 66t CNC control R-axis (backgauge) CNC controlled CNC-controlled crowning Fiessler Akas 2M laser safety device 2 additional backgauge fingers (total 4) 1 set of top and bottom tooling - Further processing lengths and capacities available upon request with appropriate accessories! -

Condition: new, Year of construction: 2026, functionality: fully functional, type of input current: three-phase, warranty duration: 12 months, Equipment: cabin, Paint/spray booth dimensions without fan and control Panel! Extraction surface - dimensions (mm): 4430(w)x1900(h) Overall dimension(mm): 4530(w)x2350(h)x1910(d) Technical data: Bljdpfxoia Taxs Acvof - Fan power 4.4kW (ATEX) - Fan suction capacity: 24000 m³/h (max 1200Pa) - Lighting: 2 pcs 2x58W (ATEX) - Connection voltage: 400V - Frequency converter for smooth regulation of the fan - Three-stage air filtration - Intended for explosive environments - EX - Complete technical documentation - CE Documentation - Warranty Possibility to order machines in various individual configurations and dimensions! Do not hesitate to contact us

Condition: new, Year of construction: 2025, functionality: fully functional, The CNC BAYKAL Hybrid Press Brakes combines all the benefits of both hydraulic and all-electric press brake systems into one. If you’re looking for press brakes that are fast, accurate, and energy-efficient, BAYKAL is the way to go. The CNC BAYKAL Hybrid Press Brakes can significantly save energy, save fuel, improve bending efficiency, reduce the risk of oil leakage, reduce installation costs, extend the service life of consumables, improve bending accuracy, reduce noise, and improve the working environment. The CNC BAYKAL hybrid press brakes system are designed with an individual electro-hydraulic servo drive system and servo pumps to control the for each of the left and right cylinders. The servo motor controls the output flow of the oil pump according to the program setting, and then controls the movement speed and position positioning of the slider, and there is no throttling phenomenon in the whole process. Therefore, all the energy output by the oil pump is supplied to the left-right oil cylinder. This control method does not have any energy loss, and the energy-saving effect is very prominent. With this system the hydraulics run on demand when the foot pedal is activated, rather than having a pump running continuously. This results in lower energy usage than a standard hydraulic machine as well as faster cycle times and extremely high accuracy. The flow and pressure of Y1 and Y2 oil cylinders are respectively controlled by two sets of servo bidirectional pump systems, and the oil in the upper chamber of the oil cylinder is directly pumped into the lower chamber of the oil cylinder through the oil pump to realize the lifting of the beam. The reverse rotation of the oil pump pumps the oil in the lower chamber of the oil cylinder directly into the lower chamber of the oil cylinder to realize the pressing and bending of the upper die. Applicable between from 100 Tons to 1250 Tons, the synchronization of the left and right of the upper beam of the CNC BAYKAL hybrid press brakes is controlled separately by two sets of servo bidirectional pumps. Bljdpforq D Nijx Acvof

Condition: as good as new (ex-display), Year of construction: 2026, Compact wide belt sander with combined sanding unit Action equipment: - Switching the sanding shoe on and off from the control panel - Switching the roller on and off from the control panel - Electronic control Fox 500 KTR - Table extension with 2 rollers with infeed and outfeed - Automatic table positioning with push button Item number: 5222100A2 Also for smaller craft workshops for occasional use Combination sanding unit with sanding shoe for fine sanding As standard with angular grooved steel roller Ø 120 mm for calibrating Fine adjustment of the working height Clearly arranged control panel on the front side Robust tube-stiffened monoblock steel machine body, robot-welded, working units mounted high up for maximum rigidity Motorized height adjustment of the work table with digital display Electronically controlled sanding belt oscillation Carpet feed via gear motor with two speeds Natural rubber feed carpet with negative profile Bljdpfogf Sw Nsx Acvof Flexible steel pressure rail in front of the first unit Rubber pressure rollers, in front of or behind each working unit Pneumatic belt tensioning for each unit with decimal correction option for grain size / belt thickness Universal use for solid wood and veneer thanks to combination unit Entry model for smaller companies Working width 950 mm Equipment details Combination unit for calibrating and grinding Angled steel roller Ø 120 mm with fine height adjustment Hard grinding shoe with graphite support Universal design for calibrating