Punching unit punching bracket

Raskin 25 BL 160 Ausladung 110 mm

Year of construction: 2026, condition: new, Magnetic separator for spool transport line Pipe magnet with 4 magnetic plates ( permanent magnet ) Dsdpscqvhxofx Afnskh Hinged door for easy removal of the metal parts Tube diameter: 180 mm Available immediately Location: From stock 54634 Bitburg

Condition: new, plate thickness 1,6 mm 4 t blade length 156 mm Dkedpfeftd Uaox Afneh angle adjustable from - to fest Grad table surface area 450m x 305 mm total power requirement Handbetrieb kW weight of the machine ca. 95 Kg Dimensions (LxWxH) 530 x 380 x 480 mm

Condition: used, Year of construction: 2015, Industrial robot Manufacturer: Kuka Model: KR180 R3100 K prime KRC4 2015 Kuka robot KR180 R3100 K prime (console version) Year of manufacture: 2015 Dkjdpfx Ajwnt Rlofnjh Reach: 3,096 mm Weight: 1,059 kg Payload: 180 kg Kuka controller KRC4 Weight: 150 kg Software V8.5.4 Interface: X11 Interface: Beckhoff EtherCat Kuka touch panel KCP4 Kuka connection cables 22126ä

Condition: ready for operation (used), Year of construction: 1997, sheet width 3230 mm plate thickness 2.5 mm thickness at "Niro-steel" 1.5 mm no. of strokes 28 - 42 Hub/min cutting angle 1.60 Grad table height 820 mm distance between columns 3540 mm Control ELGO 87P engine output 6.8 kW weight of the machine ca. 3410 kg. range L-W-H 4070 x 2070 x 1400 mm from a maintenance workshop including special accessories (!!) Equipment: - robust / motorized swing cut guillotine shears - break-proof, torsion-free steel welded construction - compact and clear machine design - NC electro-motorized back stop - including NC ELGO "TYP 87P" digital control unit * adjustable from the front right * with target/actual value position input * continuous adjustment over the entire travel range * rough adjustment via push buttons Dkodpfxsxacd Ne Afnoh * protection of the limit values ??with limit switch - "Duo-Cut" drive with two dynamic, powerful gear motors - support table with recessed grips - hold-down bar with hard rubber strip - all-steel knife with two cutting edges - selector switch for single and continuous stroke - 1x freely movable foot switch - safety device at the rear - original operating instructions Special accessories included: - pneumatic sheet holding device for thin sheet metal cuts - 1x extra long side stop, including support foot + digital stop - 2x extra long, front support arms * with "SLIDING" mount - for easy moving

Year of construction: 2025, condition: new, The AL-KO Sanding table AST 1.5 BASIC is the entry-level model for the AL-KO sanding table program. It is certified according to GS-HO-11 and bears the seal "Wood dust tested according to BGI 739-1". It is therefore suitable for manual grinding as well as for machining workpieces with manual work machines. The grinding table is made of galvanized steel sheet. The workpiece support consists of a removable beech wood grate. It is accessible from all 4 sides. So that several people can work at the same time. Thanks to the sturdy, structurally stiffened construction, workpieces with a weight of up to 150 kg can be processed. In order to adjust the work surface of the AL-KO AST 1.5 BASIC to the required working height, it is equipped as standard with a mechanical height adjustment. The height adjustment is done without any tools by adjusting the feet in scaled grid dimensions. In addition, all feet can be adjusted in millimeters according to the respective ground conditions. The extraction trough is optimized in terms of flow technology. Due to the funnel-shaped design of the trough with integrated air duct, the air stream is directed to the intake socket. Depending on the extraction capacity required, the connection to the customer-specific extraction system can be made via a connection piece Ø 140 or Ø 160 mm. The bending of the machining surface on both two longitudinal sides also allows machining of workpieces on the end face The suction grilles are aligned with the flow connection to the suction port and thus guarantee an optimal extraction result. For cleaning work inside the sanding table, the slat grating can be lifted off and the air duct can be removed by loosening a few screws. Dkodpofyadbjfx Afneh The sanding table is delivered pre-assembled, only the feet have to be mounted and adjusted to the required working height. Tender specification AST 1.5 BASIC page 2 from 2 Technical data AST 1.5 BASIC: - Intake socket 140/ 160 mm - Required suction performance 1.500 m³/h - Vacuum on socket at 22 m/s 1.000 Pa bei Ø 140 mm 700 Pa bei Ø 160 mm - Working height adjustable 735 – 1.015 mm - Working surface (W x L) 946 x 1.500 mm - Dimension (W x L) 1.000 x 1.600 mm - Weight approx. 73 kg

Condition: used, Year of construction: 1993, Technical details: sheet width: 3050 mm plate thickness: 6,0 mm distance between columns: 3460 mm no. of strokes: min./max.: 9 / 17 Hub/min back gauge: 750 mm (motorisch) mm cutting angle: 0,5° - 3,0° ° cutting gap adjustment: manuell mm down holder: 18 Stück (hydraulisch) Stück Table dimensions: 380 x 3100 mm total connected load: 7,5 kW weight of the machine ca.: 4,56 t dimensions of machine: L: 3,64 x B: 2,55 x H: 1,58 m Djdpfx Afsu Rni Honjkh Equipment: With side stop L: 1000 × W: 100 × H: 60 mm and stop bar 990 mm, with 8 supports Operation via control panel and foot switch Cutting zone lighting Stroke counter Machine feet *

Year of construction: 2022, condition: as good as new (ex-display), AL-KO grinding table AST 1.5 BASIC The AL-KO grinding table AST 1.5 BASIC is the entry-level model for the AL-KO grinding table program. He is certified according to GS-HO-11 and carries the seal of "Holzstaubgeprueft according to BGI 739-1" THEIR advantages accessible from 4 sides Take loads up to 150kg Manual, tool-free height adjustment with scale Contrasting sides for edge grinding Workpiece-friendly beech wood grid (removable) Funnel-shaped air Guide to the dust extraction spout TECHNICAL DATA LOAD 1.5 BASIC Intake 140 / 160 mm Required suction power 1.500 m ³/h Negative pressure at the connection at 22 m/s 1.000Pa in DN140mm 700Pa at DN160mm Dkjdpfxsdqzhbe Afneh Working height adjustable from 735-1.015 mm Working surface (BxL) 946 x 1, 500 mm Dimensions (Wxl) 1, 000 x 1 600mm Weight 73 kg

Condition: new, Year of construction: 2025, Mechanical sheet metal guillotine METFORMER Djdpfx Afjfwmydenokh HCO-2x2000mm The guillotine is made entirely of steel, the structure is solid and heavy. Simple design with good looks. It is easy to use. This guillotine is widely used for cutting thin and medium steel sheets in light engineering, hardware manufacturing. The blade is made of a super strong steel alloy. Technical data: Model, HCO-2x2000, Engine power, kw, 3.0, Maximum sheet thickness (mm), mm, 2, Number of knife changes, pcs, 4, Length, mm, 2800, Width, mm, 1260, Height, mm, 1300, Weight, kg, 1350,

Condition: like new (used), Year of construction: 2017, operating hours: 64 h, functionality: fully functional, machine/vehicle number: 665901, overall weight: 1,154 kg, load capacity: 210 kg, arm reach: 3,096 mm, This is a KUKA KR 210 R3100 ultra industrial robot Year of manufacture 2017 We are also happy to offer you this robot overhauled! The robot includes the following options: BoardPackage EthernetKRL LoadDataDetermination Profinet KRC-Nexxt RemoteService SafeOperation UserTech Dedpfx Afju Nzzaenjkh

Condition: used, external dimensions: Width/Height: 65 mm Dkedpfeb N Nd Ujx Afnsh Length: 2600 mm Weight: 70 kg