Used Switzerland for sale (245)

Condition: new, Year of construction: 2023, functionality: fully functional, space requirement width: 2,889 mm, space requirement length: 11,292 mm, space requirement height: 2,675 mm, overall weight: 36,000 kg, temperature: 150 °C, operating pressure: 6 bar, pressure: 6 bar, power: 110 kW (149.56 HP), type of input current: AC, operating temperature: 150 °C, Equipment: documentation/manual, Equipment Type: Dry Product Capacity: Circa 500kg/hr Design Conditions: 150oC; 6barg/ Full Vacuum Materials of Construction (Product Wetted): 304L SS, Viton O-Ring, PTFE Reinforced Flat Gaskets Electric Motor: 3 Pole / 480V / 60Hz, 110kW, 1780 rpm, Eex de IIB T4, IP 65; Horizontal, Single-Shaft, Continuous, Vacuum Kneader- Dryer Single step direct (contact) evaporation/drying process 3 heating zones on shell, 2 heating zones on agitator Twin screw feeder General Applications: Drying of products exhibiting multiple phase change e.g. Liquid –> highly viscous –> pasty–> free flowing powder or granular solid Ability to handle foaming, stickiness, crusting & required variation of temperature and drive input requirements Self-cleaning design and heavy duty/high torque to promote heat and mass transfer Potential Applications: Drying of a crystalline mass, e.g. Anti-Oxidants: Hodpfot Uqldsx Aacsfn Typical solvents: Methanol, Cyclohexane, Isopropanol Industrial Residues: Recovery of hazardous / valuable materials from wastes. E.g. TDI (Polyurethane monomer) from distillation residue Drying of paint and lacquer sludge Recovery of water/toluene from rubber residues Recovery of solvents from vitamin distillation residues Polymerisation Reactions..

Condition: like new (used), Year of construction: 2006, operating hours: 367 h, SPIRO pipe production machine made of galvanized and stainless steel sheet 0.4-1.0 mm thick, used, in very good condition, serviced. Hfedpfov Rx Trox Aacon

Condition: like new (used), Year of construction: 2018, 4th Generation of The XXL system by Imaging Solutions 5-in-1 solution. A LayFlat book block producing from sheets in just one working step. One push of a button triggers all of the necessary individual steps: cutting, creasing, folding, pressing, and gluing. LayFlat book blocks are produced with minimum manpower requirements, and same-day finishing and shipping is possible. Specifications: 2300 sheets per hour XL format book blocks up to 370 mm x 457 mm (14.5” x 18”) High-level performance: up to 250 book blocks/h Barcode controlled product selection: Hjden Ut D Nspfx Aacofn Different page lengths and book configuration (inlays) within one roll possible thus reducing time for batching Optional inlay feeder with a stacking height of 220 mm (8.66”) Unlimited number of inlays can be glued between two pages Active adjustment of gluing head for precise and homogeneous glue application Optional in-line book press for perfect book spines Easy to operate via touchscreen 5-in-1 fully automatic print finishing system Cutting, creasing, folding, pressing and gluing in only one workstep Complete LayFlat book blocks manufactured from sheets Integratable into barcode-controlled workflows (e.g. inline with 3-knife-trimmer) Provides consistent premium quality with low production costs Premium LayFlat photo book technology for panoramic pages Processes original photo paper and digital press paper.

Condition: used, Year of construction: 1989, Studer Type S40-4 CNC Cylindrical Grinder with Studer Siemens Control, Centre Height 225mm, Centre Distance 1600mm, Wheel Head Slide Max Travel 275mm, Marpass E39 Gauge, Wheel Size 400mm x 80mm x 127mm, Speeds 2 100rpm, Filter Mist. S/No. 7234.22 (1989). Country of Origin: Switzerland Hfsdexnlg Njpfx Aacsn A charge of £750 for dismantling and loading onto suitable transport will be automatically added to your invoice should you be successful in purchasing this item. Blocking and securing will be at the cost of the purchaser. Please Note: This lot is located in Birmingham, UK

Condition: used, Year of construction: 1990, Manufacturer: Indosa Origin: Switzerland Year: 1990 (fully upgraded in 2006 with Siemens automation) Main machine: Indosa Matic 100 automatic seamer Filling / dosing: AW7/500 module Extraction / dedusting: CK-V09 system Accumulation table: ZT800 Hfsdpfx Ajw Epywoacsn Transport: 12-station star wheel Product feed: Pneumatic transfer Machine type: Automatic filling and seaming line for cans / jars / tins / rigid containers Can type: Metal or composite Applications: Dry and granular products Examples: Tobacco, pellets, dry foods, solid products Capacity: Up to 40–50 units/min (integrated variable speed) Can diameter: Ø 80 mm standard (other sizes available upon request) Can height: 20 to 320 mm Dosing type: Weighing (vibrator + bucket) Product feed: Pneumatic transfer Seaming: Metal lids, integrated seaming module Extraction: Integrated CK-V09 dedusting module Lid magazine: Yes Control: Automated Documents available in digital format. Condition / Additional information: Operational video available

Year of construction: 2021, condition: new, Excellent value for money Mobile in the workshop can be used *. High suction power significantly reduced dust (dust class L) Robust, reliable construction Options: filter cartridge, floor cleaning kit *. From the frame up robust engine, economical in terms of energy consumption, strong in the suction power. The AL-KO raw air dust extractors Mobile family are easy to handle and can be due to their low weight and the integrated castors always there, where you need their suction power. * In the wood and wood products, raw air dust extractors are not approved for use in workplaces in Germany, Austria and Switzerland. * Standard incl. 2 meters hose Technical data suction pipe of 160 160 mm motor nominal power 1.5 kW / 3 pH voltage 400 V / 50 Hz Flow rate 2,200 m³ / h vacuum 2,500 PA filter surface 2.2 m 2 chip sample volume 175 liter Dimensions (L x B x H) in mm 1,090 x 580 x 2,098 Weight 40 kg Hedpfscnz A Tsx Aacefn Location: Off the shelf 54634 Bitburg

Condition: new, functionality: fully functional, Year of construction: 2025, The EVO is the latest innovation in sheet metal processing. It is equipped with numerous innovative and patented features that increase your production capacity and productivity, while offering the lowest total cost of ownership. The high-quality components used in this machine, as well as the latest version of the BENDtronic® control system, which is installed as standard on all EVO machines, are particular highlights. HAEUSLER EVO 21015 4-Roll Bending Machine / Roll Bending Machine Manufacturer: Haeusler Type: EVO 21015 4-Roll Bending Machine / Roll Bending Machine Origin: Germany / Switzerland Condition: NEW, Display Machine Availability: 12-14 weeks Capacity: Working width 2100 mm Rolling capacity 12 mm Pre-bending capacity 9 mm Standard Equipment: • Variable swing arm adjustment of the side rollers VSA® • HAEUSLER Hybrid Drive System HHDS® • Movable 21.5" touchscreen control panel including high-end BENDtronic® control • Continuously adjustable rotation speed between 0 and 8 m/min • Machine prepared for remote maintenance • Electromechanical holding system for the rotation of the upper roller • Automatic pressure adjustment of the lower roller • Automatic pressure compensation of the Bottom roll cylinders: Standard cooling system for ambient temperatures up to 35°C • Automated axis optimization • Automatic hydraulic shutdown for roll positioning • Ultra-compact design to reduce or even eliminate foundation costs • Safety ripcord Optional equipment: • Two-roll drive for the top and bottom rolls • Cone bending device for bending conical workpieces • Advanced cooling system for ambient temperatures up to 45°C • Top support for easier bending of large diameters • Side support for assisting with bending of large diameters • Gas pressure accumulator for calibrating previously welded cylinders • BendIT-Office workstation software • Autonomous bending Hfjdsxnnf Iopfx Aacsn • Machine prepared for quick top roll changes • Interchangeable top rolls with different diameters for bending small-diameter sections • Hardened rolls for bending black and stainless material • Infeed roller conveyor for easy sheet feeding into the machine • Centering device for the infeed roller conveyor, for automatic centering of sheets before bending Not the right machine? As a Haeusler representative, we can customize and offer you the machine you need. Don't hesitate to contact us.

Condition: good (used), Year of construction: 1988, Ref. -No.: 10396 Manufacturer: KELLENBERGER Type: 600 U - Nr. 40 Year of construction: 1988 Type of control: Konventionell Control: N/A Storage location: Halberstadt Country of origin: Switzerland Distance between center: 600 mm Center height (standard): 125 mm Hsdjxmd R Repfx Aacefn Height of centers by lifting work blocks head and tailstock: 175 - 250 mm Swing diameter with lifting blocks max.: 350 - 500 mm Table swivel / each side: 10 ° Dwell time of the table reversal: 0 - 5 Sec Diameter / width / hole: 250 x 13 x 76 mm Speeds of the grinding wheel spindle: 1500/1700/2200/3600 Swiveling grinding wheel head: 360 ° Cross movement of the grinding wheel head: 285 mm Quickly pulling the wheel head back and forth: 40 mm Intermittent injection for each reversal of the table: 0,001 - 0,03 mm / dia Micro-corrector of the feed, 1 division of the dial: 0,001 mm / Ø Working speeds continuously adjustable (normal / special): 20-400/10-400 Max. Grinding length: 900 mm

Condition: excellent (used), Year of construction: 2023, operating hours: 1,851 h, functionality: fully functional, pressing force: 70 t, filling opening width: 1,100 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 500 kg, overall weight: 17,000 kg, oil tank capacity: 70 l, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410 BS-22/50 Year of construction 2023 Pump operation hours 1,851 hours, as of July 24 Press power main press 70 t (a 70 tonne hydraulic cylinder is installed, special equipment) Specific press force 90,9 N/cm² (a 70 tonne hydraulic cylinder is installed, special equipment) Feed channel 1,400 x 1,000 mm Theoretic cycle time 13 sec Theoretic throughput capacity 266 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 22 kW Connected load 65 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 5,5 t/h bulk weight of 50 kg/cbm approx. 7,5 t/h bulk weight of 100 kg/cbm approx. 9,7 t/h Bale weight with a bale length of approx. 1.2 m up to 500 kg, depends on material SPS controller Siemens S7-1500 Operating panel Schneider Harmony Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 17 t Special equipment: Wear-resistant floor made of HARDOX steel Larger main hydraulic cylinder with 70 tonnes of pressing force Special press ram for pressing loose bulk materials with small grain sizes OptiCut XS system for lower cutting forces and higher throughput rates Special pressing piston for pressing "difficult" materials Technical data for the conveyor belt: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Deutschland Type KGF GB 1500 Year of construction 2023 Drive power 4.0 kW Belt speed approx. 0.3 m/second Length feeding conveyor 2,679 mm Length elevating conveyor 6,866 mm Length goose neck 1,272 mm Grade 35° Effecting width 1,400 mm Side wall height 800 mm Carrier height 50 mm Carrier distance 750 mm Belt quality EP 400/3, 3:1 (DIN quality N) Overall height 4,515 mm Overall transport dimensions11,148 x 2,502 mm (l x w) Technical data on the non-contact personal protection system: Manufacturer BOREMA Umwelttechnik AG, Switzerland Type APSS iBOR 22 Hsdpfx Aju Thbxsacofn Year of construction 2023 Condition of the press system: The entire system is in very good condition due to the short operating time of only 1,851 pump hours and the processing of only paper, cardboard and film. Scope of delivery: Avermann baler, type AVOS 1410 BS-22/50, incl. wire drawing stations and bale chute Avermann conveyor belt, type KGF GB 1500 BOREMA personal protection system, type APSS iBOR 22 Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: ready for operation (used), Year of construction: 2000, Immediately available from toolmaking in Switzerland: 5-axis milling machine Deckel Maho Type: DMU 35 M Year of manufacture: 2000 CNC control: Heidenhain TNC 310 M Electronic handwheel Table: 400 x 280 mm Table load up to 100 kg Travel X/Y/Z: 350/240/340 mm Stepless spindle speeds: 0 – 5000 rpm Taper: SK 40 Rapid traverse: 5 m/min Hfjdpfxoxn R Dts Aacjn Servomotors for X/Y/Z axes Swivel range: 360° Table clamping: +105/–150° Weight: 2 t Tool holders, hydraulic vise Price: EUR 6,500 plus VAT ex works location.

Condition: excellent (used), different measuring clamps from 100 - 250 mm : 100 - 125 mm make Steinmeyer 125 - 150 mm make Mitutoyo 150 - 175 mm make Steinmeyer 175 . 200 mm Make Mitutoyo 200 - 225 mm make Pierre Roch Switzerland 225 - 250 mm make Mitutoyo all measuring clamps are in cassettes total. Weight 8 kg Hfsdpegz Amkofx Aacen

Condition: new, functionality: fully functional, Year of construction: 2025, operating hours: 100 h, control type: CNC control, degree of automation: automatic, actuation type: electric, controller manufacturer: Bosch Rexroth, controller model: Han´s 901, laser type: fiber laser, laser source manufacturer: Han´s Laser, laser hours: 20 h, laser power: 12,000 W, laser wavelength: 1,050 nm, sheet thickness (max.): 40 mm, sheet thickness steel (max.): 40 mm, sheet thickness stainless steel (max.): 30 mm, sheet thickness aluminum (max.): 30 mm, sheet thickness brass (max.): 20 mm, sheet thickness copper (max.): 20 mm, table length: 3,000 mm, table height: 700 mm, working length: 3,000 mm, working width: 1,500 mm, travel distance X-axis: 3,100 mm, travel distance Y-axis: 1,600 mm, travel distance Z-axis: 100 mm, feed rate X-axis: 280 m/min, feed rate Y-axis: 280 m/min, cutting speed: 10,000 mm/min, repeat accuracy: 0.05 mm, workpiece weight (max.): 2,150 kg, power: 12 kW (16.32 HP), input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, type of cooling: water, compressed air connection: 14 bar, overall weight: 10,000 kg, total length: 10,000 mm, total width: 2,550 mm, total height: 2,200 mm, warranty duration: 12 months, Equipment: CE marking, centralized greasing system, cooling unit, documentation/manual, dust extraction, emergency stop, fume extraction, safety light barrier, Trade Fair Demonstration Machine, Brand New Machine at an Unbeatable Price! The machine on offer is a new 2025 demo model that was exhibited at the EMO trade fair in Hannover in September 2025 and is now looking for its first owner. This is a brand new machine! Demonstration system! The original list price of this machine is €295,000. Our exceptional one-time offer for this machine is €210,000! Including delivery within Germany, installation, and training. No hidden additional costs. The machine will be available for inspection from October 2025 and testing from December 2025. Sample cuts and cutting videos are available. Machine description below: G3015 HF Expert 12kW Fiber Laser Cutting Machine 1.5 x 3m with hydraulic shuttle table and extraction system, including delivery, installation, CAD CAM software, and training. Our high-end fiber laser cutting system with top-quality components and unmistakable design. Cutting Area X-axis [mm]: 3100 Y-axis [mm]: 1600 Z-axis [mm]: 150 Max. Speed [m/min]: 280 Acceleration: 3 g Precision [mm]: 0.03 Repeatability [mm/m]: 0.02 Dimensions Length [mm]: 10,000 Width [mm]: 2,550 Height [mm]: 2,200 Max. sheet weight [kg/table]: 2,150 Available laser powers: 6 kW, 12 kW, 20 kW, 30 kW Cutting Capacity – Quality Cut/Separation Cut Steel: 30mm/40mm Stainless Steel: 25mm/30mm Aluminum: 25mm/30mm Brass: 14mm/16mm For processing the following materials: Steel, stainless steel, aluminum, copper, brass, titanium, and nickel alloys Fully enclosed for optimal laser safety Compact design saves shipping costs and shortens installation time Hollow structure design, suitable for up to 60 kW Improved accessibility via full-length side sliding door Ergonomic loading and unloading for small workpieces High load capacity for heavy materials thanks to hydraulic shuttle table High dynamics and productivity due to powerful controls and motors Integrated electrical cabinet and laser source with maintenance-friendly access Various automation solutions available Rapid service response thanks to Remote Service feature Fully enclosed machine with OD5+ laser safety glass windows CE compliant The electrical cabinet, laser source, pneumatic system, lubrication system, and table drive motors are fully integrated within the main machine frame. Easy visual inspection via the side sliding door Comfortable loading and unloading via the side sliding door Simple cutting of a wide range of small workpieces Faster response times for demo cutting Higher Dynamics & Productivity Thanks to the optimized machine bed and extruded aluminum gantry, equipped with the fast real-time "Han’s 901 (Rexroth)" controller and powerful Rexroth motors, the HF Expert achieves very high speeds and acceleration. Configuration and component selection Control system: Han’s 901 (Rexroth, Germany) Servo drivers: Rexroth, Germany Cutting head: Han’s Laser Linear guides: Hiwin, Taiwan (China) Rack: Güdel, Switzerland Gearbox: Güdel, Switzerland Servo valve: Lanny, Germany Machine frame: Han’s, China Gantry: Han’s, China Z-axis: Han’s, China Hfodpfxjxlt Hfo Aacon Shuttle table: Han’s, China

Condition: new, mileage: 45 km, power: 129 kW (175.39 HP), overall weight: 8,550 kg, fuel type: diesel, color: white, axle configuration: 4x2, maximum load weight: 4,895 kg, empty load weight: 3,655 kg, fuel: diesel, wheelbase: 3,400 mm, driver cabin: day cab, gearing type: automatic, emission class: euro6, suspension: other, loading space width: 2,000 mm, loading space length: 4,000 mm, loading space height: 400 mm, total length: 5,700 mm, number of seats: 3, Equipment: ABS, air conditioning, central locking, cruise control, differential lock, hydraulics, immobilizer system, onboard computer, soot filter, trailer coupling, Fuso 9C18 Duonic City Hooklift, available immediately, also for rent with purchase option - Speed limiter 40 km/h for Switzerland - Containers in various designs optionally available from approx. €3,500 - Gross vehicle weight: 8,550 kg, Unladen weight: 3,655 kg, Payload without container: 4,895 kg - Downrating to 7.5 t possible, payload then approx. 3,850 kg - Automatic transmission (Duonic) - Limited-slip differential lock - Batteries 2 x 100 Ah - Trailer coupling, ball head, 3,500 kg, incl. electrical kit (factory fitted) - Heated exterior mirrors - Automatic climate control - Radio pre-installation - Reverse warning system - PTO with increased engine speed (factory fitted) - Battery cover and AdBlue tank cover - Preparation for battery isolator relay - Traction tires (all-weather M+S) Continental - Seat covers - Optional installations: reversing camera, beacons, cover panels, net/strap box, etc. - Various containers in stock or available to order - 3-year / 100,000 km factory warranty, Fuso is a brand of Daimler Truck AG Hooklift System Installed on Fuso 9C18 - Hooklift system for containers according to DIN 30722 Part 3 - Lifting/pull capacity 6,000 kg - Container length: 3,500–4,000 mm - Hook height: 900 mm - Hydraulic articulated hook arm (low lift angle) - Hydraulic container locking (acceptance of third-party containers possible, secure transport) - Mechanical hook safety lock - Cable remote control mounted on the A-pillar, operation possible outside the cab, additional mechanical emergency operation on device - Emergency stop function Hfsdpfjwv Ebxex Aacon - CE certificate and kit box - Final paint finish: Unit Black RAL 9005 / Rollers Black RAL 9005 Errors and prior sale reserved! - More info, further XXL images on our homepage - For inquiries in English please call Features: automatic climate control, automatic transmission, VAT deductible, ABS, radio, on-board computer, cruise control, heated mirrors, electronic immobilizer, central locking with remote control, trailer coupling, power steering, differential lock, tinted windows, tachograph, cab: day cab, air-suspended driver’s seat, electric windows, PTO, new vehicle, Emissions standard: Euro 6, diesel, rear-wheel drive, excellent condition, HSN 7149, hydraulics, consumption: 0.0/0.0/0.0 l/100 km (combined/urban/extra-urban), particulate filter, rental option available, particulate emissions sticker: 4 - green.

Condition: used, Bystronic Byspeed 3015 – Laser Cutting Machine with Bytrans Automation (2007) Manufacturer: Bystronic Laser AG, Switzerland Model: Byspeed 3015 Year of Manufacture: 2007 Machine No.: 652 Job No.: 30006335 Equipment No.: 10022619 Technical Specifications: • Working area: 3000 x 1500 mm • Laser power: [please confirm exact laser source in kW, typically 3–4.4 kW for this model] • Voltage: 3x400 V, 50 Hz • Connected load: 52 kW • Max. current: 125 A • Proportion current of biggest consumer: 39 A • Total weight: 800 kg (control cabinet unit, machine heavier in total) Included Equipment: • Bytrans automation system (automatic loading & unloading) • Dust extraction system – included and in good working condition • Cooling unit (chiller) – included and in good working condition Hodpfexgnzgox Aacjfn • CE certified • Made in Switzerland Condition: • Used, generally in good condition • Note: The turbo requires repair. A quotation for approx. €7,000 has been received. Apart from this, the machine is well maintained. • Still installed – can be inspected in operation upon request • Available immediately

Year of construction: 2014, operating hours: 3,824 h, condition: used, 2014 | Terex Finlay 883+ Spaleck | Used Screen | 3824 hours 📍Location: Switzerland, Lufingen 🚛 Delivery available to your destination – Use our shipping calculator to estimate transport costs! 💰 Buy Now for EUR 49000 or Make an Offer. Payment at delivery available for an affordable fee (subject to approval)* 👷‍♂️ Inspected by an independent expert 71 inspection points 61 approved ✅ 10 imperfect ℹ️ 0 issues ⚠️ 📌 Inspector's Comment: A TEREX machine that has been well-used and appears poorly, worked at a scrap metal yard and exhibits significant aggressive metal corrosion, including on the feeder belt. It has a nicely running CAT C4 engine, with oil and filters replaced over 300 hours ago. There is a lot of scrap metal between the moving parts. The machine is operational, but there is a lot of rust, the drivetrain is noisy, and the drive chain is rusted solid. The drivetrain could use some attention. The rear side belt has been replaced with a new one, and lubrication was adequate during the inspection. The back conveyor belt has been placed beside the front one because the machine was positioned against a wall inside. The feeder shows significant corrosion on the underside. All hydraulic functions are operational during the inspection, with no leaks or issues noted. However, the longer the machine remains in the yard, the more severe the corrosion becomes. 📄 Want to see the full inspection, extra photos, or a video? Tip: The reference "39722 Equippo" is commonly used when looking up more details online. 💡 Why this machine and our service stands out: ✔ Thorough inspection by professionals Hjdpfx Aexly Tlsacsfn ✔ Jobsite delivery available ✔ Money-Back Guaranteed ✔ Secure and flexible payment options 🔄 Considering other equipment options? We offer helpful tools and resources for all equipment owners and operators – easily accessible on our platform.

Condition: ready for operation (used), Year of construction: 2000, operating hours: 59,827 h, General Data Machine weight 16600 kg Main Drive Pressing force 2000 kN Hfodoxllnnspfx Aacsn This HAMMERLE BM 200 - 3100 press brake was manufactured in 2000. It is a robust and reliable machine, ideal for bending applications. Consider the opportunity to buy this HAMMERLE BM 200 - 3100 press brake. Contact us for more information. Application Types Bending

Condition: used, Year of construction: 2020, operating hours: 6,000 h, Digital Plotter Cutting System, Manufacturer: Zünd - Switzerland Year of manufacture: 2020, original purchase price verifiably over €80,000 net! Model: G3 M-1600 The machine is fully functional and available for inspection and demonstration at any time. Machine location: Bayreuth ____ Please find below some details from the 2020 order: Working area: Width: 1330 mm, Length: 1600 mm Triple module carrier, laser pointer, adjustable vacuum area Integrated Tool Initialization (ITI) for modules 2 and 3, right side User manual in German included 3-phase 400 V (323 V – 457 V) 50 Hz CEE32 External compressed air supply required Material clearance: 60 mm With appropriate tooling, materials up to 50 mm thick can be cut Workstation Bracket for two modules and three tools, including storage space Monitor mount, compartment for PC. Max. PC dimensions: Width 200 mm, Height 480 mm, Length 470 mm, with compact keyboard (USB + PS/2 ports) Vacuum turbine 1–9 kW 3ph 400 V (50/60 Hz) Automatically regulated vacuum for material fixation, energy-efficient Extension kit for 1–9 kW / 1–15 kW vacuum turbine Enables placement of vacuum turbine up to 5 m from the cutter. Includes bracket for vertical silencer placement Universal Module UM-ZS* For use with various cutting and drawing tools Cutting mat PLP (anthracite) S3/G3 M-1600 Thickness: 2.5 mm, Width: 1410 mm, Length: 1984 mm, 2-piece Cutting tool UCT Universal Cutting Tool, including spring-mounted glide shoe and 2 blade holders types 1 & 3 Blade set for UCT/SCT cutting tool 14 blades: 4 x Z10, 10 x Type 6 Zünd Cut Center Software Suite V3.x For intuitive and simple operation of a Zünd Digital Cutter. Includes Cut Server, Cut Manager, Cut Editor for a single PC. Cut Queue For automated workflow and reporting, including unlimited number of hotfolders Camera option For edge detection, “best fit”, “fit to object” and “fit to job” compensation Integrated compact color camera ICC Ensures perfect detection of almost all registration marks, even with low color contrast, poor lighting conditions, and when processing reflective materials. Hjdexlzyyspfx Aacofn Includes 3 sockets for connecting powered tools Frame grabber card For controlling the ICC camera via Zünd Cut Center Software _____ All information is without obligation; errors excepted. Used machines are exclusively sold to commercial buyers and without warranty.

Condition: good (used), Year of construction: 2006, functionality: fully functional, Universal Precision External Cylindrical Grinding Machine Studer S32 + Seckler Automation Hfjdpowzbybsfx Aacsn Manufacturer: Studer AG Switzerland CH Model: Studer S 32 + Seckler Modulo 300 Automation Control unit: Fanuc 16i TB CNC Year of construction: 2006 Condition: Well-maintained, original Machine weight approx.: 6,000 kg Accessories: - As shown in photos - Documentation - Coolant system Machine inspection under power can be arranged at short notice. If you have any further questions, please do not hesitate to contact us. Price ex stock, plus VAT. Condition: good - ready for demonstration Delivery: ex stock, as inspected Payment: strictly net – upon receipt of invoice Subject to prior sale and errors. We look forward to receiving your order. More machines and equipment available from stock – please inquire. We look forward to hearing from you.

Condition: excellent (used), Year of construction: 2002, operating hours: 34,000 h, functionality: fully functional, Agie Excellence 2F, year 2002. Machine in excellent condition. Can be inspected at our premises in Semsales, Switzerland. Hfjdpew N Tazsfx Aacsn

Condition: excellent (used), Year of construction: 2007, functionality: fully functional, Automated saw for quality sorting of boards – Edger-Crosscut Saw-Conveying Unit for Sawmill Timber Grading JRIMAC Twin-Cut This installation is designed for sawing and optimal sorting to separate grades. Edger (complies with current safety standards): Cutting length 6.0 m – Cutting height 120 mm – Maximum cutting width against stop 380 mm – Retractable saw blade cuts in both directions (forward and reverse) – Pressure bar with safety device – Positioning lasers – Adjustable cutting speed. Crosscut Saw: Cutting unit at both ends – Unit 1 is fixed – Unit 2 can be positioned at 4,000 mm, 5,000 mm, and up to 6,000 mm. Conveying Unit – The board is fed from the right to the edger by toothed wheels – The operator rips the boards longitudinally and marks the quality (X, O, //, etc.) – Offcuts are automatically discharged at the rear into a trolley – The edged timber is conveyed and crosscut automatically to the desired length – End trimmings are ejected into containers or bags – The timber continues on roller tracks to be picked up and stacked by a third party according to its grade. Scissor Lift Table (not included in the machine price): Upstream, the timber is placed on a scissor lift table and brought to the height of the edger/operator. Hfjdjxm R U Aepfx Aacon 400 Volts – 63A – 22 kW – 550 mm blade diameter – Control panel with programmable touch screen Machine dimensions: Length 8.80 m x Width 4.40 m x Total height 3.50 m – Length of conveying unit to stacking area: 15.0 m – Full footprint fits within a rectangle of 8.80 x 19.5 m – 3,200 kg Existing customer base: There is currently a steady clientele in French-speaking Switzerland for timber selected based on quality criteria – This external market is also available for sale. The machine is in good technical and visual condition – Available mid-December 2025 (Y07-pa300k-ppoc100k/pv30k)

Condition: reconditioned (used), Year of construction: 2007, operating hours: 16,730 h, functionality: fully functional, travel distance X-axis: 600 mm, travel distance Y-axis: 400 mm, travel distance Z-axis: 450 mm, workpiece weight (max.): 1,600 kg, total height: 275 mm, total width: 300 mm, total length: 300 mm, table width: 750 mm, Charmilles FO550S. 16-position rotary tool changer. Erowa ITS50 chuck. Machine currently being serviced at our premises in Semsales, Switzerland. Inspection possible upon request. Further information available on request. Hfsdpfsxmidpjx Aacen

Condition: refurbished (used), Year of construction: 2007, operating hours: 15,125 h, functionality: fully functional, workpiece weight (max.): 1,500 kg, travel distance X-axis: 550 mm, travel distance Y-axis: 350 mm, travel distance Z-axis: 400 mm, total height: 200 mm, total length: 260 mm, total width: 280 mm, workpiece height (max.): 400 mm, workpiece width (max.): 700 mm, workpiece length (max.): 1,200 mm, type of input current: three-phase, overall weight: 3,300 kg, Charmilles Robofil 440SLP, 2007. Only 15,100 hours of work. Machine fully serviced and working. Viewable at our Semsales premises in Switzerland. Hfjdpfxov Rbxwe Aacjn

Condition: excellent (used), Year of construction: 2006, operating hours: 4,245 h, functionality: fully functional, travel distance X-axis: 350 mm, travel distance Y-axis: 250 mm, travel distance Z-axis: 350 mm, workpiece weight (max.): 400 kg, total height: 259 mm, total width: 185 mm, total length: 270 mm, table width: 450 mm, table length: 600 mm, year of last overhaul: 2024, tank capacity: 400 l, Agie Hyperspark 2HS. Viewable in our workshop in Semsales, Switzerland. Machine in excellent condition. Hsdpfxov T U Tyj Aacsfn Low operating hours. 26-position tool changer.

Condition: refurbished (used), Year of construction: 1998, operating hours: 20,800 h, functionality: fully functional, travel distance X-axis: 350 mm, travel distance Y-axis: 250 mm, travel distance Z-axis: 300 mm, Machine currently undergoing revision at our facility in Semsales, Switzerland. Erowa ITS50 chuck. 16-position rotary tool changer, double gripper. Flat LCD screen. Retractable work tray. Inspection possible upon request. More details available on request. Hsdsxlhudopfx Aacofn

Condition: excellent (used), Year of construction: 2005, operating hours: 27,000 h, functionality: fully functional, travel distance X-axis: 350 mm, travel distance Y-axis: 250 mm, travel distance Z-axis: 250 mm, empty load weight: 2,500 kg, Equipment: documentation/manual, Machine in excellent condition. Machine already cleaned. Hodpfxov Im R Ts Aacofn Sold as is or revised on request. Machine visible in our premises in Semsales in Switzerland.