Used Slit Pliers for sale (389)

Condition: good (used), Year of construction: 2012, functionality: fully functional, machine/vehicle number: 668, cutting width (max.): 2,500 mm, overall weight: 2,000 kg, total length: 3,000 mm, total width: 2 mm, total height: 2,200 mm, input frequency: 50 Hz, input current: 10 A, Equipment: crane, This machine is unique! It has a working width of up to 2500 mm and requires very little space. In addition, it can independently lift the rolls and also lift the finished rolls out of the machine using a crane. The working speed is approximately 172 m/min, and the maximum winding diameter is 400–550 mm. The machine has 5 knife holders and a positioning laser for the empty cores. It can process 76 mm (3 inch) as well as 152 mm (6 inch) cores. The unwinding brake is regulated via an ultrasonic sensor to ensure consistent winding tension. The machine has 2 ionizing bars to prevent static charging. Nodo Aban Ejpfx Abyedc

Condition: used, 72”x 0.5” x 60,000Lb Braner Turret Type Loop Slitting Line Braner Turret Type Loop Slitting Line is used for coil metal cross cutting with maximum width 72”, maximum 0,5” metal thcikness and 60,000Lb coil capacity Make: Braner Year New: 1996 Material Thickness: .060″ – .500″ Material Width: 12″ – 72″ Coil Weight: 60,000Lb Line Speed: 120 – 250 feet per minute Coil ID: 20″ – 24″ Coil OD: 75″ Slitting Cap: .500″ / 4 cuts – .125″ / 40 cuts Entry L-Type Coil Car Hydraulic Lift & Traverse Self Contained Hydraulics Control Panel Mandrel Uncoiler Powered Hold – Down Roll Outboard Bearing Support Hydraulic Feed-Up Drive Water Cooled Brake Hydraulic Peeling Table Driven Entry Pinch Rolls Adjustable Edge Guides Entry Mechanical Crop Shear Two Turret Type Slitting Heads Arbor Diameter: 12″ Powered Arbor Adjustment Powered Head Rotation Motor: 100HP DC Drive Lots of Knives & Tooling Two (2) Scrap Winders Powered Open / Close Heavy Duty Design Looping Pit Cross Over Table Drag Board Tension Stand Material Feeding Table Recoiler Hydraulic Drum Powered Push Off Hydraulic Over-Arm Separator Outboard Bearing Support 300HP DC Motor Drive Nsdpfern Sqhsx Abyjdc Exit L-Type Coil Car Hydraulic Lift & Traverse Self Contained Hydraulics Upgraded Siemens Digital Drives, Electrics, Controls, Knives & Tooling

Condition: used, Year of construction: 2023, functionality: fully functional, machine/vehicle number: 625RS10HWPp-D22092022, coil weight: 10,000 kg, feed rate X-axis: 35 m/min, number of straightening rollers: 5, sheet thickness aluminum (max.): 2 mm, sheet thickness steel (max.): 2 mm, sheet thickness copper (max.): 2 mm, inner diameter: 508 mm, sheet thickness (max.): 2 mm, outer diameter: 1,250 mm, mandrel diameter: 508 mm, coil width: 1,250 mm, coil outer diameter: 1,250 mm, number of blades: 8, type of input current: three-phase, working width: 1,250 mm, total width: 4,500 mm, total length: 5,700 mm, total height: 1,600 mm, load capacity: 10,000 kg, product width (max.): 1,250 mm, space requirement width: 4,500 mm, space requirement length: 5,700 mm, space requirement height: 1,600 mm, Krasser Centurio SCS-1250 slitting line with a Stolarczyk 10-ton motorized uncoiler For sale: a complete coil-fed sheet metal cutting and slitting line, manufactured by Krasser GmbH (Austria), installed new in January 2023 and used in-house ever since by a sheet metal processing company. Well-maintained, fully operational, and available for inspection while still running at our facility. Krasser Centurio SCS-1250 – slitting/cutting line Max. sheet/coil width: 1,250 mm — min. independent sheet width: 250 mm — min. slitting width: 75 mm between knives Material thickness range: steel (400 N/mm²) 0.4–1.5 mm, stainless steel (550 N/mm²) 0.4–1.0 mm, copper and aluminum 0.5–2 mm Max. cutting speed: 35 m/min Straightening unit: 5 rollers Longitudinal cutting: 6 pairs of slitting knives installed (5 standard + 1 additional pair), max. 8 Cross-cutting: electrically driven guillotine shear Roller-shear unit for partial cross-cuts included Automatic film-application (plastic protective film) unit included Automatic labeling unit included (label printer + applicator) Krasser Optimizer cutting-optimization software included Touchscreen HMI control, multilingual (including Spanish) CE-certified safety fencing Electrical connection: 3-phase 400–488V, 11 kW, 16A Pneumatic connection: 1/2", 6 bar, filtered and dried air, 50 l/min Approx. overall footprint (line + uncoiler): 5.7 m long x 4.5 m wide x 1.6 m high Lifetime production data (as of today): 176,941 m of material processed, 60,610 cross-cuts — machine has been in steady, reliable production use Stolarczyk uncoiling set (motorized, 10 tons) Manufacturer: Spółka Stolarczyk (Poland) — Type RS10HWPp-D, year 2022 Max. coil load: 10,000 kg (10 tons) Ndodpfx Ajz D Ivvjbyjc Hydraulic mandrel expansion — mandrel/coil inner diameter 508–610 mm Max. coil outer diameter: 1,250 mm — coil width: 250–1,250 mm Max. unwinding speed: 30 m/min Coil car included, with hydraulic vertical lift (306 mm) and electric horizontal travel Electrical connection: 400V, 6.5 kW Weight: 3,150 kg The line and uncoiler are sold together as a working unit. Removal/dismantling and logistics to be agreed with the buyer. For technical questions or to arrange a visit, please contact us by email — we're glad to answer any question and share further documentation, photos, or a video of the machine running.

Condition: ready for operation (used), functionality: fully functional, machine/vehicle number: 603737, type of input current: three-phase, product width (max.): 1,150 mm, For sale is a heavy-duty industrial Slitting and Rewinding Machine manufactured in Germany by Frank'sche Eisenwerke AG (Frank Spezial-Maschinen) under the renowned System Hofmann & Schwabe license. This robust machine is designed for continuous, high-precision slitting and rewinding of technical packaging materials, paper rolls, pressure-sensitive tapes, and specialized plastic films. Built with German heavy engineering standards, it delivers maximum stability, high structural rigidity, and long-term operating reliability. The unit comes complete with an automated/manual core loader & feed assembly side-unit, making it a comprehensive setup for converting facilities. Key Features & Capabilities: Proven German Engineering: High structural durability ensuring low vibration during continuous production runs. Versatile Converting: Suitable for slitting self-adhesive tapes, foil substrates, paper, and flexible packaging materials. Ndjdpfj Adu Dgex Abyec Integrated Feeding Unit: Includes a dedicated side hopper and guide channel for paper core feeding and roll handling. Operator Interface: Control panel mounted directly on the frame for convenient operational oversight. Condition & Transport: Condition: Used, mechanically intact and complete with side auxiliary table. Availability: Immediately available for inspection and disassembly/loading upon request.

Year of construction: 2008, condition: ready for operation (used), functionality: fully functional, paper width (max.): 1,800 mm, Unwind diameter: 1,000 mm Rewind diameter: 800 mm Max. speed: 400 m/min Friction shafts for 3 and 6 inch Hydraulic lift at the unwind station Splicing table Web edge control Tidland knife holders, 20 pieces Semi-automatic knife setting system from Tidland Recipe management Laser positioning We will also dismantle and load the machine onto a truck or sea container at our own expense. Ndjdpfxeywl D Ne Abysc

Condition: like new (used), Year of construction: 2025, functionality: fully functional, FORSTNER nuSLIT longitudinal slitting and cut-to-length line, year 2025. The machine is in excellent condition and fully operational. It was used only at several exhibitions and in a demo center. The machine is designed for longitudinal slitting and sheet cutting operations. It is fully programmable, with automatic adjustment of the longitudinal slitting knives. Longitudinal slitting into 6 strips (5 pairs of knives) with the possibility to mount up to 7 pairs. Equipped with a modern F3 control system featuring a touchscreen interface, which allows easy programming of different lengths, widths, and quantities. The controller communicates with an electronic eye, automatically sets the zero point, and enables precise, clean perpendicular cuts. Integrated material-saving function – the machine stops, the slitting knives are raised, and the sheet is automatically fed into the shears. Comes with complete technical documentation. Specification: Model: FORSTNER nuSLIT 1250 Made in: Austria Year: 2025 Working width: 1250 mm Max. thickness: up to 1.0 mm Longitudinal slitting knives: 5 pairs Cutting: rotary shears Controller: F3 Other features: automatically adjustable longitudinal slitting knives Ndodpfx Aey Dfnnobyec If you have any further questions, we will be happy to assist you.

Condition: excellent (used), Year of construction: 2023, functionality: fully functional, machine/vehicle number: 133/SCS, cutting speed: 35,000 mm/min, working width: 1,250 mm, feed rate X-axis: 35 m/min, product width (max.): 1,250 mm, number of straightening rollers: 7, We are offering a very well-maintained Krasser CENTURIO 1250 stand-alone slitting line, manufactured in 2023, for sale. Highlights Reinforced 7-roll leveling unit Max. coil width 1,250 mm Cutting speed up to 35 m/min Suitable for longitudinal and transverse cutting as well as leveling of strip steel Modern control system with touch operation Very well-maintained condition Ready for immediate use Technical data Manufacturer: Krasser Model: CENTURIO 1250 Type: Stand-alone slitting line Year of manufacture: 2023 Condition: Very good Max. coil width: 1,250 mm Min. coil width: 250 mm Description The Krasser CENTURIO 1250 is a powerful sheet metal cutting system for the precise processing of steel, stainless steel, aluminum, copper, and zinc sheets. The reinforced 7-roll leveling unit is particularly noteworthy, as it enables excellent leveling quality and reliable processing of a wide variety of materials. The system is currently still in operation and can therefore be inspected at any time by appointment while running. This offers interested parties the opportunity to directly verify the condition, performance, and functionality of the machine. The machine is expected to be available in the first quarter of 2027. The exact date may vary slightly depending on the project, but we currently anticipate a release around February 2027. Early reservation or coordination of the delivery date is possible and desirable. Contact For further information, technical details, or to arrange a viewing appointment, we look forward to receiving your message or call. Category ID: 1052 Nsdpfxjzvgbqs Abyedc Type ID: 136 Type: Slitting line

Condition: used, Year of construction: 2018, functionality: fully functional, number of straightening rollers: 6, conveyor belt width: 1,300 mm, sheet thickness steel (max.): 1 mm, coil width: 1,250 mm, cutting length (max.): 6,400 mm, straightening roller diameter: 70 mm, space requirement width: 3,500 mm, space requirement length: 18,275 mm, space requirement height: 4,000 mm, Single-person operation, rapid access to a wide variety of sheets, automatic sheet changeover, standard sheets remain loaded in the system; the upper sheets are less common types; secure solution with a movable access aid for loading the upper decoilers; programmable slitting line with 8 pairs of knives in station version; slitting knives are alternately arranged for distortion-free cutting; rotary knives of the AL p with 100 mm diameter to achieve minimal incision; 7.2 m long conveyor belt for discharging the strips. The system layout PDF is shown as a mirror image! Njdpjxwc E Iefx Abyedc

Condition: excellent (used), Year of construction: 2020, operating hours: 97 h, functionality: fully functional, machine/vehicle number: 098 / SCS, # KRASSER Centurio 1250 – Year of Manufacture 2020 – Slitting Line with 5 Automatic Knife Pairs, Leveling Unit, and Guillotine Shear For sale is a very well-maintained KRASSER Centurio 1250 from the year 2020. The machine was taken from an operational business and is in very good, immediately operational condition. It is ideally suited for sheet metal workshops, roofing companies, facade builders, and sheet metal processing companies for the economical processing of coil material. A special advantage: the machine recently underwent a comprehensive service by the manufacturer, Krasser, as part of the take-back process. ## Technical Data * Manufacturer: KRASSER GmbH, Austria * Type: Centurio 1250 * Year of Manufacture: 2020 * Machine Number: 098 / SCS * Power: 32 kW * Connection: 3 x 400–488 V AC, N + PE, 50–60 Hz * Weight: approx. 3,600 kg ## Equipment * 5 automatic knife pairs Njdpfezcunaex Abyjdc * Integrated guillotine shear * Leveling unit * Robust industrial design * High production output * Precise slitting results The KRASSER Centurio 1250 impresses with its high manufacturing quality, reliability, and economy. The extensive equipment enables efficient and precise processing of coil material while simultaneously reducing setup times. The machine is immediately available and ready for sale. Inspection is possible by appointment.

Condition: used, Year of construction: 2026, Slitting line 1500 x 6, made by GUIDA Line composition: Njdpeymciaofx Abyodc - Loading coil car - Uncoiler with sliding base and single expanding mandrel - Pressure arm - Feeding telescopic table with cutting edge and deflecting roll - Entry pinch roll - Crop shear - Tilting table - Mechanical centering device - Calming rolls - Slitting shear - Looping pit equipment (entry and exit saddles + connecting tables) - Felt press - Deflecting rolls - Titling table - Recoiler with single expanding mandrel - Separator arm - Electric equipment - Hydraulic equipment - Safety fences protection - Several tooling and accessories - Spare parts Material to be processed: Hot rolled carbon steel Material tensile strength: 400 N/mm² Coil width max.: 1.500 mm Thickness: 1 - 8 mm Coil weight: 20 Tn Coil inside diameter entry: 500/600 601 + steel spacers for bigger diameter Coil external diameter Entry/Exit: 1.700 mm Slitting shear mandrels diam.: 220 mm Blades diameter: 355 mm Line speed: 50/25 m/min with manual speed change gear Working Direction: From left to right Power supply tension: 380/50 Hz

Condition: good (used), Year of construction: 2019, functionality: limited functionality, machine/vehicle number: 377/2019, cutting width (max.): 1,000 mm, type of input current: three-phase, input current: 25 A, working width: 1,050 mm, input voltage: 380 V, input frequency: 50 Hz, Equipment: documentation/manual, TTR and hot foil slitter/rewinder. TTR1000 Material width: max 1050mm Nsdpjz R Rdrjfx Abyodc Max unwinding diameter: 700mm Max rewinding diameter: 150mm Max jumbo core length: 1100mm Rewinding shafts with tooling: 1 inch and 1/2 inch Slitting system: razor blade manual set 2 rewind turrets (upper and lower) for easy change The machine is generally in good condition. It has tension control issues on one of the shafts, likely related to the magnetic powder clutch. The machine is still installed and ready for production, so we can arrange a live demo.

Condition: like new (used), Year of construction: 2016, functionality: fully functional, machine/vehicle number: 747894.2, overall weight: 187 kg, For robot use. Nsdpfxovca Tdj Abysdc Pressing force: 55 kN Total stroke: 98 mm Power stroke: 7 mm The TOX Pressotechnik TZ 05.747894 hydropneumatic clinching pliers are a powerful solution for the precise joining of materials such as steel and aluminum. With its robust design and hydropneumatic drive technology, it enables stable connections without additional welding materials. The ergonomic design ensures easy handling and reduces the physical strain on the operator. Thanks to its compact design, the TZ 05 can be easily integrated into existing production lines. The integrated safety mechanism ensures safe operation, making it the ideal choice for companies.

Condition: used, The SAMO slitting line, 2001 processes material up to 1,000 mm wide and is integrated with the PROMEC packaging line, 2019. (N19). Installed electrical power is 451 kW; Area 365 sq Meters Capabilities include: Coil Inside Diameters: 400 / 500 Coil Outside Diameter: 1,500 mm Strip width: Entry: 350–1,040 mm Exit: 20–1,020 mm Thickness: 0.3–3.0 mm Line Direction; Left to Right Siemens S7-400 PLC Installation includes: Coil Stand- 3 Coils Uncoiler with Snub Control Roll Motor: 26.5 Kw DC Edge Control, EMG Paper Winder Peeler Table Pinch Roll Crop Shear Vollmer Contact Thickness Gauge, Slitter Head Motor Drive: 72Kw, DC 400 Volt Edge guiding with automatic adjustment before slitting head Horizontal guide rolls before slitting head Shaft OD: 180mm Slitting Knives OD: 280mm Scrap winder Edge guiding at exit Rotating tooling turnstile on rails – 4 sided with 2 arms per side Pit with Pit Car Tension stand: Tension stand on linear rails Material table with horizontal and vertical position 4 horizontal guide rolls – pneumatically engaged 3 Roll Tension bridle roll system as material break Bridle roll motor: 138kW DC Crop shear Material table Re-coiler: Full hydraulic drum Overhead separator arm Motor: 190kW DC drive Ground level L-Shape coil car with overhead hold down arm 4 – arm coil turnstile with push-off arm (5) Above ground Coil Cars All hydraulics and Controls PROMEC Packaging line: (See below) Underground coil car in front of Turnstile Scale PROMEC PACKAGING LINE, 2019 Layout Code: N19 Automatic packaging system serving the SAMO slitting line. Installed electrical power: 65 kW. Processes strip widths from 40–200 mm and thicknesses from 0.2–3.0 mm. Siemens S7-400 PLC First table: Tilting table with mandrel for coil handling Signode Strapping Machine Overhead Manipulator- Horizontal Coil Handling with expanding mandrels into ID or 3 arm OD clamping Nsdpfx Aez Iq U Nebyodc Packages eye to the sky or eye to wall. All hydraulics and Controls

Condition: like new (used), functionality: fully functional, machine/vehicle number: 656377.1, overall weight: 170 kg, Nominal point diameter: 8mm Die depth: 1mm Dimension X: 0.90mm Dimension X min.: 0.8mm Dimension X max.: 0.95 Max. Pressing force: 55kN Deflection constant: 27.63 kN/mm Zero position: 95.8mm The clinching pliers from Tox Pressotechnik with servo drive have been specially developed for use in robot systems and offer a precise and efficient solution for joining sheet metal and materials. Nedpfxou Tuqtj Abysdc With its modern servo drive technology, it enables a highly dynamic and controlled application that can be ideally integrated into automated processes. The pliers are characterized by their robust design and reliability, making them a durable and low-maintenance solution. Thanks to its flexibility and versatility, it is ideal for various industrial applications and helps to increase productivity and quality in manufacturing.

Condition: used, BÖLLHOFF Type: 9524-640-824-5 RIVSET Punch Rivet System with Punch Rivet Pliers Operating voltage: 400V 50 Hz Rated current: 12A Main fuse: 35 A Control voltage: 24 V Signal voltage: 0-10 V with Hydac cooling unit OK-EL2S/3.0/M/400-50/1 max. permissible riveting pressure: 250 bar max. permissible riveting force: 78 kN Weight of the pliers: approx. 279 kg Year of manufacture: 2012 The system was inspected by the manufacturer and is fully functional. Condition: used Scope of delivery: (See picture) Nsdozgaabopfx Abyedc (Changes and errors in the technical data are subject to change!) We will be happy to answer any further questions you may have by phone.

Condition: used, BÖLLHOFF Type: 9524-640-826-7 RIVSET Punch Rivet System with Punch Rivet Pliers 9524-640-826-7 Operating voltage: 400V 50 Hz Rated current: 13A Ndedpozgaanofx Abysc Main fuse: 20 A Control voltage: 24 V Signal voltage: 10 V Year of manufacture: 2011 Max. permissible riveting pressure: 250 bar Max. permissible riveting force: 78 kN Weight of the pliers: approx. 195 kg The system was inspected by the manufacturer and is functional. Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data are subject to change!) We will be happy to answer any further questions you may have by telephone.

Condition: ready for operation (used), Year of construction: 2001, operating hours: 120 h, functionality: fully functional, machine/vehicle number: 638 TTR, film width: 1,100 mm, The Slitter Dusenberry is a slitting and rewinding machine manufactured by Dusenbery® Converting Systems. Ndodsz Rq Ebepfx Abyec

Condition: refurbished (used), Year of construction: 2016, Stainless Slitter 1500x3, made SAMO OCEMI Completely revamped in the year 2016. Technical specifications Thickness minimum: 0,4mm Thickness maximum: Up to 4mm with Rm 400N/mm2 | Up tp 3mm with 700 N/mm2 Coil width: max 1.540 mm. Max coil weight: 16 t Direction: left to right Speed: up to 150 m/min. Scope of supply · Coil car, hydraulic, Over floor · Decoiler, hydraulic expansion, with DC motor 28 kW-717-2.200 rpm, for dynamic brake and energy recovery. Stationary disk brake. Motorized snubber roll. Paper rewinder. Alignment. · Coil opener with telescopic table. Ndsdpfx Asymcmfsbyoc · Feeding unit with pinch-roll and 3-rolls straightener. · Centering unit (motorized) with 3 flattening rolls (poliurethane). · PVC film applicator (new 2017) · Slitting head, shaft diam.: 200 mm. DC motor 72 kW 780-2.652 rpm + stationary brake. · Turnstile knife charger – 2 arms couples. · Tension pinch-roll DC motor 23 kW 1.960 rpm + stationary brake. Scrap table, movable, with scrap conveyor. · Scrap rewinder, single drum dimension 600x600. Ac motor 15 kW with inverter. · Bypass table (loop) · Braking car (movable) with: - double separating roll - Deburring pinch-roll (new in 2017) - Felt press - Braking rolls-with DC motor 33kw-2.550 rpm for strip tension adjustment and energy recovery. - Cross cutting shear (crop shear) - Deflector roll - Recoiler, hydraulic expansion, separating arm with automatic lifting system. DC motor 114 kW 800-2.400 rpm + stationary brake. · Discharging coil car, over floor, with press arm. · Turnstile arm 4 x 20 t, motorized · Electric EQUIPMENT (NEW in year 2016). Supply voltage 3x380V Consisting of: Cabinet Dimension mm 5.600 x 600. With PLC Siemens S7-300. N. 3 operator switchboards. The main switchboard with HMI touch-screen Siemens Touch · Hydraulic equipment. Hydraulic power pack with oil-air cooling. Manifolds with electric valves on each machine, 24 V DC · Complete safety fences, mechanical/optical. · Cutting tools (knifes approx. 160 pieces, spacers, separating discs..). Documentation Foundation drawings Electric drawings. Hydraulic plan. PLC and HMI Software. CE declaration of Conformity Thickness minimum: 0,4 mm Thickness maximum: Up to 4 mm with Rm 400N/mm2 | Up tp 3 mm with 700 N/mm2 Coil width: max 1.540 mm Max coil weight: 16 t Speed: up to 150 m/min Direction: left to right

Condition: used, 1. Decoiler Brand : SCHLOEMANN Type : Hydraulic expanding decoiler Function : Coil holding and controlled rotation Expansion control : Hydraulic Frame : Welded steel base with integrated brake Estimated capacity : 8–12 tons Coil bore : Ø 508 mm ----- 🔹 2. Straightener / Pinch Roll Manufacturer : COMEC (Société de Constructions Mécaniques de Creil) Type : Pinch roll and leveler Control : Mechanical Order number : 1305.1268 Recommended lubricants : Shell Macoma, Tellus, Alvania (as per nameplate) Function : Feeds and flattens strip before slitting Secondary role : Synchronized strip puller ----- 🔹 3. Slitter Ndsdpfx Aow Dd Igjbyjc Manufacturer : COMEC Type : Circular blade slitting machine Drive : Mechanical gear train Blade adjustment : Manual Blades installed : ~10 sets (visible) Function : Longitudinal slitting of metal sheets into narrow strips ----- 🔹 4. Shear (End Cropper) Manufacturer : COMEC STAMCO Type : Rotating or inline shear Function : End cropping or final length cut Control panel : Electromechanical (visible on photo) Machine Application Complete line for metal coil slitting, producing narrow strips from master coils, with upstream flattening and final end cutting. Features / Differences – Heavy-duty hydraulic decoiler by SCHLOEMANN – Mechanical straightening section from COMEC – Manual-adjust slitter with circular blades – Outfeed shear for end trimming or final cut-to-length – Older but industrial-grade line, suited for medium gauge materials

Condition: excellent (used), Year of construction: 2017, Ref: 11038 . 2017 Rollem 36” Jetslit + 30” Rollaway and Cassette Delivery High volume print finishing system to maximizes finishing productivity for large volume producers For greeting cards, photo books, direct mail, postcards, invoices, business cards, game cards and much more. Features: This flexible system takes full press sheets and converts them to finished products in one step, eliminating the need for guillotine cutting, excess manpower and paper movement. 100% accuracy of finished products is a key feature of the Jetslit. Performs multiple print finishing steps with one system Bi-directional slitting, cutting, creasing and perforating in one machine Ideal for high volume production Ndodpfx Ajxyxr Nebyoc Multiple-up layouts maximize press sheet Decreases excess labour costs Eliminates touch points and paper movement Fully integrates with press via DFA communication system Accepts sheets in-line from press or operates in a stand-alone near-line configuration Process: The system takes full printed sheets with multiple images and converts each sheet in two directions, as shown below: 1. Full sheets are fed into the JetSlit registration guide for perfect alignment. 2. The sheets are completely slit on the extreme edges and timed slit in-between with Rollem's patented strike-slit feature. 3. The sheets are turned 90 degrees and re-registered. 4. Final slits are made, removing the notched portions and leaving the final pieces. Specification: Speed: Up to 6,000 cut product sheets per hour Format: Up to 36’’ (915mm)

Condition: used, SLITTING LINE GEORG 1500x1.5x25 Main technical data Ndjdpfxsxl R A Rs Abyoc Coil thickness: 0.24 – 1.5 mm Uncoiler coil weight: 25 Tn Coil width: 230 - 1500 mm Coil outer diameter: Max. 1850 mm Working speed: 200 m/min Slitting tolerance: +/- 0.125 mm Line direction: Right to left Recoiler coil weight: Max. 16 Tn 2 Slitting heads PLC: Siemens S7 1200 Cutting capacity: number of cuts with 350 MPa 24 cuts for thickness 0.25 mm 28 cuts for thickness 0.50 mm 21 cuts for thickness 0.75 mm 18 cuts for thickness 1.00 mm 15 cuts for thickness 1.25 mm 12 cuts for thickness 1.50 mm Scope of supply 1. Coil Carriage 2. Uncoiler 3. Guiding system with 2 measured edges 4. 203.2 diam. Pinch roll before shear 5. Double interlock table 6. Slitting shear:Shaft diameter: 160 mm 7. 1 off line quick change slitting head available 8. Scrap press and conveyor 9. Intermediate coil table 10. Loop Pit and covering tables 11. Strips Braking Unit 12. Motorised recoiler with hold down separator arm 13. Unloading Coil Car 14. 4 arms turnstile 15. Electrical cabinets & Control panels 16. Existing tooling 17. Existing documentation Coil thickness: 0.24 – 1.5 mm Uncoiler coil weight: 25 Tn Coil width: 230 - 1500 mm Coil outer diameter: Max. 1800 mm Working speed: 200 m/min Slitting tolerance: +/- 0.125 mm Line direction: Right to left Recoiler coil weight: Max. 16 Tn Slitting heads: 2 PLC: Siemens S7 1200 For thickness 0.25 mm: 24 cuts with 350 MPa For thickness 0.50 mm: 28 cuts with 350 MPa For thickness 0.75 mm: 21 cuts with 350 MPa For thickness 1.00 mm: 18 cuts with 350 MPa For thickness 1.25 mm: 15 cuts with 350 MPa For thickness 1.50 mm: 12 cuts with 350 MPa

Condition: excellent (used), functionality: fully functional, coil weight: 8 kg, sheet thickness (max.): 3 mm, sheet thickness steel (max.): 3 mm, total width: 1,250 mm, Slitting line for sale Ndsdpjv Twi Rofx Abysc

Condition: new, Year of construction: 2025, For customers from: Lithuania, Latvia, Estonia. Equipment for straightening, longitudinal cutting, and shearing rolled metal is an integral attribute of companies working with sheet metal. The FORSTNER company, which has long-term experience in the production of rolled metal processing machines, currently offers the market not only conventional metal shearing machines, but also equipment that performs straightening, longitudinal cutting, and shearing functions. The shearing function is performed using disk or guillotine shears. Depending on your production goals and the tasks the equipment must perform, they can be divided into four groups: 1. shearing machines; 2. longitudinal cutting and shearing machines; 3. straightening and shearing machines; 4. straightening, longitudinal cutting, and shearing machines. Njdpswd E N Ejfx Abyedc The straightening and longitudinal cutting functions of certain models of longitudinal cutting machines can be automated, which allows you to quickly and conveniently change the parameters when starting to work with another material. Forstner EASY series equipment is a machine that cuts a sheet of metal of a set length with the help of a guillotine or circular shears. EASY CUT machines are equipped with circular shears that can cut steel up to 1.0 mm thick. If you need a machine that can cut thicker metal, then it is recommended to choose the EASY PRO model with a guillotine. The working width of the machines can be 1250 mm or 1500 mm. Forstner STRAIGHT. These machines, by pulling a set length of a sheet of metal, straighten it and cut it. Depending on the type of cross-cutting knife and the diameter of the straightening rollers, the thickness of the processed metal varies from 1 mm to 2 mm. STRAIGHT and POWERSTRAIGHT also differ in the adjustment of the straightening rollers: mechanical or automatic. Integrated automatic control saves time in the long term, because changing the operating parameters of the machine is enough to press one button. Automatic control is a great choice when working with many different materials. The Forstner SLIT series is a reliable assistant when cutting rolled metal. The SLIT CUT and SLIT PRO models not only cut the metal, but also cut it lengthwise into strips of the selected width. As standard, these models are equipped with 5 longitudinal cutting knives (the maximum number of knives is 7). The main difference between the SLIT CUT and SLIT PRO models is the type of cutting knife - a circular shear or a guillotine. The Forstner COMPACT series is a device that pulls the required length of material, flattens it, cuts it into strips of the desired width and cuts sheets of a set length. The main difference between the models is the type of knife used for cutting: a circular shear or a guillotine. The flattening rollers and longitudinal cutting knives are mechanically adjusted. POWER COMPACT is a powerful equipment for flattening, longitudinal cutting and shearing rolled metal. These two models differ in working width and cross-cutting metal thickness. NuSLIT machine models are fully automated equipment. If you are looking for an automatically controlled machine that performs longitudinal cutting and cutting functions, you should choose the nuSLIT PRO or nuSLIT PROCUT models. The difference between these two models is the type of cutting knife: guillotine or segmented disc shears. NuSLIT STRAIGHT PRO and nuSLIT STRAIGHT PROCUT, in addition to the above functions, also smooth the metal sheet.

Condition: excellent (used), Cut to length - Slitter input width 1250mm Nedezyyt Iopfx Abyjdc thickness; 0.35-2.2mm input coil : 6.5ton, output 6.5 ton.

Condition: new, neu ca. 12 - 14 Wochen ab Auf Deutschland 17300 € 332.16 € 1250 mm 1.25 mm 1,25 mm bei 1 Messerpaar; 0.37 kW Nodpfx Aboz S Nzkoyjdc 36 m/min 70 mm 1900 mm 1600 mm 1000 mm 350 kg 2 pairs of blades Length measuring by wheel Digital preselection of one position Brake motor Rubber feeding rolls Manual crosscutting equipment in front and behind blade shaft with 1 cutting slide which alternaingly can be used on front and backside User manual in GERMAN OPTIONS: Additional pair of blades Decoiler