Used Scm Record 121 for sale (652)

Condition: good (used), Year of construction: 2018, functionality: fully functional, Equipment: CE marking, scorer, Horizontal panel dividing saw / Horizontal panel saw with lifting table feed Manufacturer: SCM / Gabbiani Type: Gabbiani ST 115 Year of manufacture: 2018 Horizontal beam saw with lifting table feed from the rear, originating from a parquet factory. Cutting length approx. 3200 mm Cutting depth on the lifting table approx. 1850 mm Max. stack height on the lifting table (with supports) approx. 600 mm Saw blade projection 115 mm Variable saw carriage speed 0 - 135 m/min. Variable sliding table speed 0 - 70 m/min. Motor of the main saw blade approx. 9 kW Main saw blade speed 3900 rpm Saw blade diameter 400 mm Motor of the scoring saw approx. 1.8 kW Scoring saw speed 6300 rpm Scoring saw blade diameter 160 mm 6 clamping devices (3 of which with front aligner) 2 air cushion tables, each with blower Tsdezyx Evopfx Akijd Voltage: 400 V, 3 phases, 50 Hz, 43 A Weight approx. 5500 kg Data partially estimated and taken from the brochure.

Condition: good (used), C.E. Tedozn I Hfepfx Akiod

Condition: used, SCM 320cm SiX panel saw 320cm carriage, aggregate tilting in two directions +45 to -45 degrees, blade tilt and up/down adjustment with electric motor, rip fence on the right side with electric adjustment up to 1500mm, Tjdpfjzd Uf Tsx Akiod 2-axis scoring saw with electric adjustment, 7.5KW motor, speeds controlled by a frequency inverter, max. blade diameter 550mm, carriage with angle adjustment used machine, good condition The machine has a new, non-original control system. All adjustments are functional.

Condition: like new (used), Year of construction: 2019, functionality: fully functional, SCM Superset NT four-sided planer Minimum working width: 25 mm Todpfx Akozk Ap Hoiod Maximum working width: 240 mm Minimum working height: 6 mm Maximum working height: 120 mm Number of spindles: 4 1. Bottom 2. Right 3. Left 4. Top Chrome-plated work tables Automatic electronic adjustment of working dimensions

Condition: good (used), Year of construction: 2019, functionality: fully functional, New price including transport and installation approx. €850,000 net. The machine was professionally disassembled by qualified technicians and subsequently stored. An inspection at the location in the Netherlands is possible after prior appointment. Technical data: Manufacturer: SCM Stefani Type: One 108 Cell Year of construction: 2019 Operating hours: approx. 5,600 Feed speed: 10–40 m/min Maximum speed with pickback: 30 m/min Workpiece length: approx. 250–3,000 mm Workpiece width: approx. 130–1,200 mm Workpiece thickness: 10–60 mm Maximum workpiece weight pickback: 80 kg Machine length edge banding machine: approx. 11,550 mm Installation area of the complete cell according to layout: approx. 30,270 × 13,166 mm Working height: approx. 970 mm Connection: 400 V / 50 Hz with neutral conductor Tsdpsz Aquhefx Akisd Workpiece feed: Motorized feed roller table Easy Order BN+ automatic workpiece feed Automatic alignment for longitudinal and transverse processing Servo-controlled workpiece centering Automatic adjustment to different workpiece dimensions Large lateral workpiece support Edge and glue system: Nordson AltaPUR 4HO PUR hot melt unit Melt-on-demand technology Melting capacity up to approx. 6 kg/h SGP glue reservoir with CNC-controlled glue metering Additional interchangeable SGP glue reservoir Separate preheating trolley for one glue reservoir Workpiece edge preheating Automatic positioning of the edge guide and pressure rollers 12-position vertical edge magazine with automatic edge changing Processing of roll material up to 3 mm Designed for thin edge, 20° bevel, and radii R1, R1.5 and R2 Machining units: Pre-milling unit RT-H/RT-X with 2 × 4 kW Electronic positioning of the pre-milling unit Trimming unit YU/SP-1000 with automatic saw blade inclination Flush-cutting and pre-milling unit R-E CNC-controlled RSU-E Hi-Drive Multiedge fine milling unit Processing of thin edge and R1, R1.5 and R2 Round 4 four-motor corner rounding unit Automatic selection of four profiles MX80 HSK milling unit with 10 kW CNC-controlled horizontal and vertical positioning Automatic pivoting from 0–90° Suitable for continuous or recessed grooves on the top, bottom and workpiece edge CNC-controlled RCS-E Multiedge radius drawing blade unit Edge sanding unit GT with oscillating sanding belt Two glue seam drawing blade units RCA/2C Polishing unit SP/F with oscillating Riepe polishing pads Spraying devices: Release agent spraying device at the machine infeed Antistatic and coolant spraying device Spraying device for sensitive or foiled edges Cleaning agent spraying devices for the glue seam drawing blades Spraying device for the first pressure roller Automatic pickback return: Gantry return system with three servo-controlled axes Workpiece pick-up via vacuum gripper Automatic rotation by 0°, 90°, -90° and 180° Automatic return to the machine infeed Up to 10 return cycles per minute without rotation Up to 9 return cycles per minute with 90° rotation Motorized conveyor belts Additional second unloading station Central control via the machine control system Location: Netherlands Inspection: possible after prior appointment Condition: professionally disassembled and stored Availability: short notice Price: on request The technical data were compiled based on the available original documents. Errors, changes and prior sale are reserved.

Condition: used, Year of construction: 2014, power: 6.6 kW (8.97 HP), travel distance X-axis: 3,681 mm, travel distance Y-axis: 1,655 mm, travel distance Z-axis: 250 mm, workpiece length (max.): 3,050 mm, workpiece width (max.): 1,252 mm, workpiece height (max.): 180 mm, number of axes: 3, Equipment: CE marking, documentation/manual, F11 Drilling Unit Includes: 7 independent vertical spindles (4 on the right and 3 on the left) Drill chuck M 10 / diameter 11 mm Distance between spindles 32 mm 2 double horizontal drilling heads (1+1), 1 in X and 1 in Y (drill chuck M8 / diameter 9 mm) Drill speed 4000 rpm 1 integrated saw blade in X direction (max. diameter 120 mm) Saw blade speed 5000 rpm Motor power 2.2 kW Vertical travel with pneumatic release of the entire unit 250 mm Vertical travel with pneumatic release per spindle 60 mm Extraction hood all around 6.6 kW – 9 HP electric spindle Includes: Tool holder HSK F 63 Speed 1500 - 24000 rpm Motor power (S1/S6) 5.5/6.6 kW (7.5/9 HP) from 12000 to 18000 rpm Right and left rotation Static inverter for stepless speed adjustment and immediate stopping of rotation Extraction hood all around Tool changer TR10 Tjdpfx Akoz Aubxsiod 10-position lateral tool changer for tools and angle gearboxes Central lubrication with manual pump Vacuum pump, output 90/108 m³/h at 50/60 Hz 8 TVF work tables and 18 interchangeable vacuum suction cups 120x120 mm Second set of stops Laser device for positioning the suction cups

Condition: used, Year of construction: 2023, functionality: fully functional, machine/vehicle number: AB00029039, feed length X-axis: 3,050 mm, feed length Y-axis: 900 mm, feed length Z-axis: 60 mm, input frequency: 50 Hz, input current: 31 A, feed rate X-axis: 40 m/min, feed rate Y-axis: 40 m/min, feed rate Z-axis: 10 m/min, working width: 900 mm, total width: 2,159 mm, total length: 3,459 mm, total height: 1,500 mm, SCM Startech CN Plus R F23L CNC drilling, grooving and routing centre, manufactured in Italy in 2023. The machine is currently installed in Pejë, Kosovo, and can be inspected under power by prior appointment. Machine identification: - Manufacturer: SCM - Model: Startech CN Plus R F23L - Year of manufacture: 2023 - Serial number: AB00029039 - CE version - Machine weight: 1,383 kg Main equipment: - F23L drilling head - 13 independent vertical drilling spindles: 7 in X and 6 in Y - 10 horizontal drilling spindles: 6 in X and 4 in Y - Drilling motor power: 2.2 kW - Drilling spindle speed: 4,200 rpm - 5.5 kW vertical electrospindle for routing operations - Electrospindle speed: 1,000–18,000 rpm - ER32 collet with manual tool change - Maximum routing tool diameter: 20 mm - Integrated grooving saw in the X direction - Maximum saw blade diameter: 125 mm - Saw blade speed: 5,500 rpm - Automatic workpiece positioning and side alignment Todpj Afnhhofx Akiod - Centralised lubrication system - SCM Maestro CNC software with Hicam machine interface - PC control with 19-inch display - Barcode program support - Uninterruptible power supply unit (UPS) - Additional Maestro CNC hardware key Working capacity: - Maximum panel dimensions: 3,050 × 900 × 60 mm - Minimum panel dimensions: 200 × 80 × 10 mm - Maximum axis speed X/Y/Z: 40/40/10 m/min - Maximum vertical drilling depth: 30 mm Installation data: - Electrical supply: 400 V, 3+N, 50 Hz - Input current: 31 A - Installed power: 20.7 kVA - Compressed-air consumption: 50 Nl/min The machine is used, fully functional and available for demonstration under power. Availability: by arrangement. Sale basis: EXW Pejë, Kosovo. Dismantling, loading and transport can be arranged separately. Further technical information, documentation and an operating video are available on request.

Condition: excellent (used), Surface planer SCM F520 Class Working width: 520 mm 4-knife cutterhead Tedpfx Aex H S Dnskied Traditional knives Electronic raising and lowering of the worktable Main fence adjustable up to 45° Table length: 2700 mm CE certificate Technical documentation (DTR) Year of manufacture: 2014

Condition: used, AD planer Minimax 310, good condition, 2.2 kW, 200 kg. Price changes reserved, subject to errors, printing and typographical mistakes. Tsdsx H Udqepfx Akiod

Condition: used, Spindle moulder SCM T130 NPS - used - fine-adjustable fence, tenoning and slotting table, right-/left-hand rotation ----- Technical Data ----- Tsdpfxew Nv Nfe Akisd Table size: 1,080 x 750 mm, Spindle diameter: 30 mm, Speeds: 3,000/4,500/6,000/7,000/10,000 rpm, Extraction port Ø: 120 mm, Lower extraction port Ø: 120 mm

Condition: excellent (used), SCM T130E Spindle Moulder with Glazing Bead Unit Spindle diameter: 35 mm Total spindle length: 140 mm Variable spindle speed via frequency inverter: up to 10,000 rpm Main motor power: 5.5 kW Unit for cutting glazing bead Unit power: 2.2 kW Electronic spindle height adjustment Electronic fence adjustment 4-roller feed Masterwood Feed speed adjustment via variator CE certified Todpfxoxbnyrs Akied DTR technical documentation Year of manufacture: 2005

Condition: used, planing width: 500 mm, SCM F5L Planer Tsdowb Er Iepfx Akisd Working width 500mm 4kw main engine 4-knife shaft Traditional knives Main fence adjustable at an angle of up to 45 Length of tops 2600mm

Condition: new, Basic equipment and accessories10-year guarantee on the guide system of the saw carriage- Saw carriage with anodized aluminum profile guide made of hardened,ground and flanged steel guides- Saw carriage length 3200mm- "READY" electronic control, 2-axis control (3rd axis onrequest) with:- Height adjustment and inclination of the saw unit (control of therip fence on request)- Management of the tool data with automatic correction of theCutting height in relation to the angle of inclination of the saw blade- Manual, semi-automatic and automatic mode with 99storable work programs- Additional functions: calculator and hour meter- Trimming frame for quick positioning of the stopmiter cuts- Table extensions in the outlet- Cutting length at the rip fence 1270 mm- 2-axis control with 99 programsMotor 7kW 50Hz (8kW 60Hz)- Motor with direct connection with push buttons- Three main saw blade speeds- Scoring unit with independent motorization, externally adjustable andStops for easy saw blade positioningSecurity/Protection- Emergency stop button on the front- Emergency stop button on the side near the rip fence (Version CE)- Thermal protection switch- Saw blade swing protection (version CE) integrated suction, suction nozzlewith a diameter of 80 mm- Saw blade swing protection with integrated suction, suction nozzle with 80 mmdiameter- Automatic motor brake on the main saw blade (CE version)- Lockable main switch- 110 V auxiliary circuit- CE Declaration of Conformity (CE version)Technical specificationsMax cutting height at 90° (mm) 140 with blade 400Max cutting height at 45° (mm) 97 with blade 400Saw blade tilt (degrees) 45Programmed lifting and swiveling of the saw blade unitSaw blade speed (rpm) 3000- 4000- 5000Scorer speed (rpm) 8500Main engine power (S6 -40%) kW (hp) 50 Hz 7 (9.5)Scoring unit power (S6 -40%) kW (HP) 50 Hz 1.3 (1.7)Format cuts:- with trolley 1600 (mm) n.a.- with trolley 3200 (mm) 3200x3200Cutting width for parallel cuts (mm) 1270Suction nozzle diameter:- on frame (mm) 120- on the saw blade guard (mm) 80- on the riving knife (mm) n.a.Net weight base machine (kg) 1050109999 Execution according to safety regulationsR10078 nova si 400ep CE version930731 volts 400 EU931201 Frequency 50 Hz570343 Digital readout for rip fenceComplete with:- Digital display and magnetic tape570133 Motor 9kW 50Hz (11kW 60Hz) with automatic star/delta switch kW9 HP12 Hz50 (kW11 HP15 Hz60)083202 base109993 MACHINE LANGUAGE: German Tjdpfx Akovxr Skeied

Condition: used, Year of construction: 2017, power: 20 kW (27.19 HP), edge thickness (max.): 12 mm, feed rate X-axis: 20 m/min, The machine has the following configuration: Pre-milling unit End-capping unit Number of motors in end-capping unit: 2 Rough milling unit, top and bottom Number of motors in rough milling unit: 2 Edge rounding unit Number of motors in edge rounding unit: 2 Edge trimming unit Glue application unit Edge finishing unit Number of motors in edge finishing unit: 2 TECHNICAL DETAILS Workpiece processing Min. board thickness: 8 mm Max. board thickness: 60 mm Min. edge thickness: 0.4 mm Max. edge thickness: 12 mm Max. feed rate: 20 m/min MACHINE DETAILS Tjdpfxozmtldj Akied Total connected load: 20 kW EQUIPMENT Preheating lamps for workpiece sides Edge roller magazine Glue reservoir for EVA hot melt adhesive Spray unit The machine is sold and delivered in its actual and legal condition ("as is, where is") based on photographic documentation and technical/commercial documents, which are for descriptive purposes only. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing, and use of the machine at the destination. External reference: 7981

Condition: good (used), Year of construction: 2005, Console table with vacuum suction plate New control system installed in 2022 (price: €9,000) Control program: Xilog Plus X-axis between stops: 2500 mm Y-axis with milling: 1240 mm Y-axis with drilling: 1080 mm Z-axis: 200 mm (max. workpiece height: 100 mm) Main spindle HSK 63 with 6.5 kW, up to 24,000 rpm 4 tool changers at the front 4 tool changers at the rear Tsdpfxezhgz Is Akied Drilling unit External dimensions: 5.8 x 2.8 m

Condition: used, Year of construction: 1986, Second-hand machine Year of manufacture: 1986 Features and technical specifications: Tedpfszk Nw Rjx Akisd Motor: 4 kW Speeds: 3,000 / 4,500 / 6,000 / 8,000 / 1,000 rpm. Spindle height adjustment via handwheel Dimensions: 1200 x 80 x 1350 mm Wooden clamping jaws Includes Holz Her 3-roller feed unit and stand with chassis Availability: at short notice Location: Röllbach

Condition: used, Year of construction: 2008, machine/vehicle number: AH005185, functionality: fully functional, workpiece height (max.): 60 mm, edge thickness (max.): 20 mm, actuation type: pneumatic, overall weight: 5,500 kg, Equipment: CE marking, We are selling a very well-maintained STEFANI SOLUTION 8000 edge banding machine. Year of manufacture: 2008 Machine length: 11,000 mm Edge band thickness: 0.5 - 16 mm Workpiece thickness: 10 - 60 mm Minimum workpiece width: 260 mm Maximum speed: 25 m/min (without using saws) Units: - Separating agent applicator - Pre-milling unit - Gluing unit - Saws - Trimming units - Buffing units Tjdpfx Aszdlabskied - Brushes - Saw for creating grooves on the surface and along the edge. The machine is in operational condition. For additional information, please call.

Condition: excellent (used), Year of construction: 2010, functionality: fully functional, Cutting length: 4300 mm Cutting depth: 4300 mm 7.5 kW main blade unit Scoring blade unit 1 fixed front table with air cushion 3 mobile front tables with air cushion Pushing carriage with approx. 7 clamps WinCut software Foot pedal for cycle start and stop Safety guards Weight approx. 3277 kg. Available starting September 2026. Tsdpfx Akoznz Uisiod

Condition: good (used), SCM Sandya 5 Tedpfx Akjzv Tzqsijd - 110 cm sanding width - 2 sanding belt speeds - Rubber-coated roller, rubber-coated roller, and shoe

Condition: ready for operation (used), Year of construction: 2014, travel distance X-axis: 3,000 mm, travel distance Y-axis: 1,300 mm, travel distance Z-axis: 80 mm, number of axes: 3, overall weight: 5,200 kg, spindle motor power: 7,500 W, spindle speed (max.): 24,000 rpm, This 3-axis SCM Morbidelli UNIFLEX HP was manufactured in 2014. It features a working area of 3,000 mm in the X-axis and 1,300 mm in the Y-axis, with a maximum speed of 24,000 rpm. The machine is equipped with 2 milling spindles and a tool clamping system of HSK-F63. If you are looking to get high-quality CNC wood machining capabilities, consider the SCM Morbidelli UNIFLEX HP machine we have for sale. Contact us for further details. • Number of milling spindles: 2 • Tool clamping system: HSK-F63 • Vertical drill spindles: 96 • Horizontal drills (X/Y): 32 / 4 • CE mark Additional equipment • Barcode reader • Enclosed fence • Light barrier Tjdezuhcgepfx Akisd • DXF interface • Software: SCM XILOG PLUS

Condition: used, Thickness planer: Max. planing width: 520 mm Max. planing height: 250 mm Cutterhead diameter: 110 mm Number of knives: 4 Cutterhead speed: 5000 rpm Manual adjustment of the working height Jointer: Total length of tables: 2130 mm Adjustable tables Noise reduction of the cutterhead Cutterhead guard Dust extraction port: 120 mm Tilting fence Power supply: 400 V Motor power: 5 kW Overall dimensions: Length: 2130 mm Tedpezu Ahkjfx Akijd Width: 1140 mm Height: 1300 mm

Condition: like new (used), Year of construction: 2005, functionality: fully functional, overall weight: 4,500 kg, The machine is in new condition. The price includes the tool. Details in the pictures. Tedpfjzwfqgjx Akied

Condition: good (used), max width of workpiece 230mm max workpiece height 130mm 6 spindles 1) Horizontal bottom 230mm 5.5kW 2) vertical right 130mm + Tsdpfx Asrqzvcskijd 3) vertical left 130mm; (2nd and 3rd spindle) 11kW 4) horizontal top 230mm 7.5kW 5) horizontal bottom 230mm 7,5kW 6) universal 230mm, adjustable 360° 7,5kW

Condition: used, Year of construction: 2012, Integrated NC machining center for windows and doors composed of: A) Automatic loader mod. "SP" Automatic loader for Base SP N. 1 moulder -Automatic loader consisting of: -Table with motorized belts -Automatic device for moving pieces from the buffer to the loading surface of the moulder * Piece length min: 450 mm max: 3200 mm * Piece width min: 40 mm max: 230 mm * Piece thickness min: 40 mm max: 120 mm * Work cycles 10/min * Chain advancement speed on the table: 7 m/min * Loading table dimensions 2800 x 2150 mm B) Automatic moulder mod. SUPERSET NT C 6 Position 1 = Planer Shaft Position 2= 1st right vertical shaft Position 3= 1st left vertical shaft Position 4= 1st upper horizontal shaft Position 5= 1st lower horizontal shaft Position 6= Group for slat recovery 2500 mm entry level Speed 6-36 m/min via inverter No. 1 - engine power 5.5 hp (4 kw) Horizontal presser before the planer with pneumatic exclusion from the panel Pneumatic exclusion from the control panel for the feed unit located before the planer shaft Tandem advance group in front of the right vertical with rapid exclusion Advance groups after the upper ones for reducing the towing distance from 620 mm to 450 mm Input guide with bearings for automatic feeders Todeixxwmopfx Akisd Electrical predisposition for the use of automatic loaders Manual centralized lubrication Pump for lubrication of the work surface with automatic drive Setup for in-line integration with INTEGRA SYSTEM - work surface raised to 970 mm - traffic light at entrance - piece counting Independent electrical panel POS. 1 High precision shaft 10 hp (7.5 kw) engine instead of 5.5 hp (4 kw) Brake for engines from 5.5 hp (4 kw) to 10 hp (7.5 kw) T-SET quick tool locking -allows tool locking/unlocking with the simple use of a compressed air gun POS. 2 High precision shaft 10 hp (7.5 kw) engine instead of 5.5 hp (4 kw) Brake for engines from 5.5 hp (4 kw) to 10 hp (7.5 kw) Vertical shaft with a useful length of 180 mm T-SET quick tool locking Electronic vertical positioning POS. 3 High precision shaft 10 hp (7.5 kw) engine instead of 5.5 hp (4 kw) Brake for engines from 5.5 hp (4 kw) to 10 hp (7.5 kw) High precision shaft Vertical shaft with a useful length of 180 mm T-SET quick tool locking Electronic horizontal positioning POS. 4 High precision shaft 10 hp (7.5 kw) engine instead of 5.5 hp (4 kw) Brake for engines from 5.5 hp (4 kw) to 10 hp (7.5 kw) Rotation speed 8300 rpm T-SET quick tool locking Electronic vertical positioning POS. 5 High precision shaft 10 hp (7.5 kw) engine instead of 5.5 hp (4 kw) Brake for engines from 5.5 hp (4 kw) to 10 hp (7.5 kw) Rotation speed 8300 rpm T-SET quick tool locking POS. 6 Glass bead recovery group Comprehends: PRL allows the automatic transition from planing to function recovery of the glazing bead and vice versa. - operating group with shaft diameter 30 mm, length 30 mm - electronic horizontal positioning - electronic vertical positioning - hardware and PLC modifications for axis management - tandem exit and modified hood second advancing group after the universal C) Connection transfer Transfer for receiving pieces from the moulder and automatic insertion into the Sott

Condition: excellent (used), CNC Flexible Automatic through-feed ROUTERING, DRILLING and CUTTING (SPLITTING) LINE Min/Max workpieces (panels) width (X axis) with PWX100: mm 250 / 3000 Min/Max workpieces (panels) thickness (Z axis) with PWX100: mm 12 / 60 Min/Max workpieces (panels) length-depth (Y axis) with PWX100: mm 100 /1200 (o 600+600) With automatic base-boards handling A) Loader (Bridge Frame) "MAHROS" Double Station, Mod. Brush CF-SX/D, (with automatic martyr panel management system) and with WEBER Double Labeller B) 1° Motorized Roller table "MAHROS" LS with 90° motorized belts (from longitudinal to transverse) C) Connection transfer, with tilter (180°, up-side-down) "MAHROS" Mod. Rib/C HS-C D) Gantry (Portal) CNC (Drilling) "MORBIDELLI" PowerFlex (PWX) 100 - N° 5 mobile consoles (workbenches) controlled by CN on the X-axis - N° 5 upper drilling units (B), each consisting of: - 2 vertical 30-spindle heads (60 in total per unit), rotating 0°-90° (X- and Y-axis) - 2 horizontal spindles (4 in total per unit), rotating 0°-90° (X- and Y-axis) Total 300 vertical drilling spindles + Total 20 horizontal drilling spindles (X and Y) Todpezxc Ncefx Akijd - 2 horizontal groups (1 R + 1 L) with 1 head each with 21 spindles (21 + 21 = total 42) E) 2° Roller conveyor "MAHROS" TR-C with 90° motorized belts (from longitudinal to transverse) F) Splitter (Longitudinal sawing-cutting) "CELASCHI" Model SPL Base 2 (for splitting panels in 2) With 3 working units. After cutting, panel width (MIN 70+70 mm; MAX 600+600 mm) G) Stacker (Bridge Frame) "MAHROS", double station Mod. Brush SSL/D (with automatic management system for martyr panels), with "WANDRES" panel cleaner