Used Rivet for sale (96)

Condition: used, maximum load weight: 36,040 kg, overall weight: 42,000 kg, axle configuration: 3 axles, first registration: 05/2025, next inspection (TÜV): 05/2027, Equipment: ABS, You can find our complete vehicle inventory with vehicles available immediately and in the short term on our website. Excerpt from the equipment. Complete equipment available upon request. Chassis * Regular ladder frame in lightweight steel with continuous crossmembers * With an extension of the chassis frame, the coupling plate is approximately 8 mm thick Hedpfozc A Afjx Abpep * with a 2-inch kingpin according to DIN 74080 / ISO 337 Suspension * Axle lift mechanism on axle 1 * Three-axle unit SAF INTRADISC * with disc brakes Ø 430 mm * ET 120 air suspension with approximately 180 mm travel Tires * Wheels with internal sensors according to UN ECE R141 * 6x 385/65 R 22.5 UNIROYAL TH 50 * 6 steel rims 22.5 x 11.75 * Offset approximately 120 mm (ET 120) Chassis components * Mechanical fifth wheel with leveling foot, approximately 24 t lifting capacity, single-sided operation on the right-hand side while driving * Storage box for: 10 side panels, folding stakes, and rear gate, fully enclosed, protected against spray water, also serves as a side protection device * 2 plastic toolboxes, waterproof, dimensions (internal) approximately 545 x 400 x 400 mm, installed at the rear, 1x on the left and 1x on the right Brake / Air suspension system * EBS system 2S/2M with stability program (includes ABS/ALB function) * EBS plug connection ISO 7638 (without connection lines) * Parking brake as a spring brake, external pneumatic connections as well as an external EBS diagnostic connection via ISO 7638 plug connection * WABCO EBS system * Air suspension system including 1 lifting and lowering valve, mounted on the left-hand side behind the axle unit while driving, driving position is set automatically * 2 non-interchangeable coupling heads at the front ISO 1728 * Air tanks for the brake system and air reservoir made of steel (EN 286-2) Floor * Flat floor approximately 30 mm thick, multiply laminated plywood * Floor sealed around the perimeter * Stake pockets for square tube inserts approximately 80 x 80 mm * Storage for a maximum of 14 square tube inserts approximately 80 x 80 (length 1,990 mm) on the front wall inside Front wall * Front wall approximately 2,000 mm high with steel corner posts, with profiled steel sheet, screwed/riveted to the frame * 2 pairs of lashing points (permissible lashing force approximately 1,000 kg per ring) on the front wall according to EN 12640, Note: If the front wall is used for securing the load, suitable lashing straps must be used to tighten the load, if the vehicle is operated without side panels and a rear gate Rear wall * Folding rear wall approximately 600 mm made of aluminum hollow profiles with 3 tension bars and T-handle locks * 2 folding steps on the inside, folding steel corner posts at the rear in the height of the side panels Side wall * 4 pairs of folding stakes in the height of the side panels * VarioFix steel hole outer frame * 4 pairs of stake holders for folding stakes on the outer frame (evenly distributed) * 24 pairs of lashing eyes in the outer frame (according to EN 12640), permissible tensile force approximately 5,000 kg per ring Side panels * 5 pairs of folding side panels approximately 600 mm made of aluminum hollow profiles with tension bars Electrical / Electronics * Lamp carrier made of steel, arranged above the underrun protection * KÖGEL LUXIMA Premium package, consisting of: LED license plate lighting, LED outline lights and reflectors at the front, flashing LED side marker lights, Superseal and bayon

Year of construction: 1999, condition: good (used), functionality: fully functional, Manufacturer: Vester Elektronik GmbH Model: Sensorchek VSC 10C Year of manufacture: 1999 Machine type: Optical measuring and sorting machine Application: 100% inspection of turned parts, stamped parts, rivets, screws, small components Technology: Optoelectronic image processing with CCD/CMOS cameras Technical Data Measuring System • 1–4 industrial cameras (CCD/CMOS) • Telecentric precision lenses • Transmitted and incident light illumination (LED flash) • Subpixel evaluation • Measuring accuracy: in the hundredth range (approx. 0.01 mm) Testable Parts • Diameter: up to approx. 30 mm • Length: up to approx. 80 mm • Material: Metal parts, turned parts, stamped parts, pressed parts Performance • Cycle rate: 100–250 parts/min • Feeding: Vibratory bowl feeder + separation • Sorting: Pneumatic good/reject ejection Hodpfxjyizrls Abpep

Year of construction: 2017, condition: ready for operation (used), A combined hot riveting and forming system for plastic components is available. Power: 38kW, Control: PLC, Weight: approx. 1850kg. Documentation available. An on-site inspection is possible. Hsdpfx Ajzfp H Ijbpjp

Condition: used, TECHNICAL DETAILS - Parts per minute : 400 - Rivet length : 12 [mm] - Drilling depth (max.) : 5 [mm] Hodpouhb Tkjfx Abpsp - Cutting diameter : 3 [mm] - Floor space (width) : 1.12 [m] - Floor space (length) : 2.21 [m] - Height : 1.77 [m] - Motor : 4 [hp/kW] - Net weight : 2,500 [kg] - Gross weight : 3,000 [kg] EQUIPMENT - Tooling as per photo

Condition: good (used), Hang 101-50 Eyeletting machine The machine is in perfect condition and ready to use. Technical specifications: 1 eyeletting head (Hang 271 rivet, hole diameter approx. 6mm) Hodozhkh Espfx Abpjp Maximum capacity: 20 sheets 230V power supply Front and side margins Operation: foot pedal or hand switch. The machine punches and crimps the eyelet in a single pass. Automatic eyelet feeding.

Condition: used, Year of construction: 1990, Technical details: Pressure: 63 t distance between columns: 200 mm stroke: 150 mm dayligth: 430 mm no. of strokes: 400 Hub/min T-slots H 12 650: 18 mm hole in table: 420x160 b x l mm ram surface area: 650 x 450 mm Hjdpfx Asu Icxqjbpep control: Wanske Tronicpress CNC passage of columns: 550x540 mm tank: 200 l stroke of ram - fixed: 100 mm ram diameter: 40 mm table height over floor: 1000 mm table: 600x450 mm table height over floor with metal base stand: 880 mm total power requirement: 30 kW weight of the machine ca.: 3,9 t Hydraulic automatic punching press for precision work (high-speed press) - for punching, drawing, pressing, minting, bending, riveting, straightening, assembling - with hydraulic gripper feed type HS 150 and 7-roller straightener (moving) - Normal strips of approx. 0.4mm - 2.5mm thickness x approx. 160mm width, as well as narrow strips up to approx. 4mm can be processed. Feed length can be adjusted as required via the control unit. - with ram round column guide - with automatic central lubrication - High-speed: up to 400 strokes min-1 - motorized adjustable fixed stop (bottom can be adjusted by hand/motorized) - Operating modes such as continuous stroke and/or single stroke Equipment: - 1x hydraulic unit - 2x control cabinets *

Condition: used, Technical details: shaft length: max. 30 mm Hodpfx Aou Nfrcebpsp capacity: 600 ST/min wire diameter max.: 5 mm working dimensions: 30 mm dimensions electric cabinet LxWxH: 1,45x0,55x2,1 m dimensions of machine: 2,95x1,5x2,15 m dimensions of coil: 1,15x1,15x1,15 m Orbital Cold Forming Machine! - Not not suitable for screw production!!!!! - mechanic cold flow press / machine is unused!!!! - Steel core bullets - Rivets (almost all types: flat rivets, punch rivets, precision rivets, flat head rivets, etc. -----à not for manufacturing semi-hollow rivets, because you will need 2 forming stages, model KEPK - 1 however only has 1 forming stage. - bolts - Pins, chain pins (short) - Lead sheath-weighting for bullets (with straight frames front and rear) - plant like new / never used! accessories: - coil, manual Machine can be demonstrated under power. Please send us your enquiry what you are going to manufacture with that machine. You can also send us a drawing in order to check it if it is possible. *

Condition: used, We are offering this used GESIPA FireFox 2 F axial pneumatic-hydraulic riveting tool, year of manufacture unknown, for sale. Manufacturer: Gesipa Blindniettechnik GmbH & Co. KG Type: FireFox 2 F axial Maximum operating pressure: 6.0 bar Serial number: Hjdpfx Abezfg Suepop If you have any questions or require further information, please do not hesitate to contact us.

Condition: used, functionality: fully functional, We are offering this used GESIPA FireFox 2, pneumatically and hydraulically powered, with an unknown year of manufacture. Hsdjzfg Ngspfx Abpep Manufacturer: GESIPA Model: FireFox 2 Drive type: pneumatically and hydraulically powered If you have any questions or require further information, please feel free to send us a message or call us.

Condition: used, Used special-purpose plant, built by ECKOLD (Special machine with superstructure for punch rivet brackets) Custom-built as a component feeder. Pictures of the components and motors. Motor brand: Behncke, 5.5 kW Hjdezc Ec Uopfx Abpop Rated power: 8.5 kW Hydraulic unit brand: FluTec, year 1999

Condition: good (used), Hang 87F 3-Head Eyeletter with Extraction Manufacturer: Hang Germany Very good condition, recently serviced. The machine is used for setting eyelets. Three eyeletting heads with adjustable spacing and the ability to deactivate a specific head. Installed waste extraction system immediately after eyeletting. Cardboard thickness: 0.2-4 mm Hsdpfx Abszfwxrepsp Throat depth: 300 mm Head spacing: adjustable from 70-320 mm Cycle time: 0.5 s The machine uses Hang No. 272 ​​rivets. Weight: 570 kg Power supply: 380 V The cycle is initiated by a foot pedal. Eyelets included.

Condition: used, maximum load weight: 36,040 kg, overall weight: 42,000 kg, axle configuration: 3 axles, first registration: 03/2025, next inspection (TÜV): 05/2027, total width: 2,550 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. Excerpt from the equipment list. Complete equipment list available upon request. Chassis: * Regular ladder frame in lightweight steel construction with continuous crossmembers * With extended chassis frame * Coupling plate approx. 8 mm thick, with a 2-inch kingpin according to DIN 74080 / ISO 337 * Axle lift mechanism on axle 1 * Three-axle unit SAF INTRADISC, with disc brakes Ø 430 mm, offset 120 * Air suspension with approx. 180 mm travel Tires: * Wheels with internal sensors according to UN ECE R141 * Tires 6x 385/65 R 22.5 UNIROYAL TH 506, steel rims 22.5 x 11.75, offset approx. 120 mm * Chassis components: * Mechanical landing gear with leveling foot, approx. 24 t lifting capacity, single-sided operation on the right side * Storage box for: 10 side panels, folding stakes, and rear flap, completely enclosed, protected against spray water, and simultaneously serving as lateral protection * 2 plastic toolboxes, waterproof, dimensions (internal) approx. 545 x 400 x 400 mm, mounted at the rear, 1x left and 1x right Braking / Air Suspension System: * EBS system 2S/2M with stability program (includes ABS/ALB function) * EBS connector ISO 7638 (without connecting lines) * Parking brake as spring brake, external pneumatic connections as well as external EBS diagnostic connection via ISO 7638 connector * WABCO EBS system * Air suspension system including 1 raising and lowering valve, mounted on the left side behind the axle unit * Driving position is automatically adjusted * 2 non-interchangeable coupling heads at the front ISO 1728 * Air tanks for braking system and air reserve made of steel (EN 286-2) Floor: * Plate floor approx. 30 mm thick, multiple-ply glued plywood * Floor sealed around the perimeter Hjdpfx Abey Trwuspjp * Pocket for square tube inserts approx. 80 x 80 mm Front wall: * Storage for max. 14 square tube inserts approx. 80 x 80 (length 1,990 mm) on the inside of the front wall * Approx. 2,000 mm high with steel corner posts, with profiled steel sheet, screwed/riveted to the frame * 2 pairs of lashing points (permissible lashing force approx. 1,000 kg per ring) on the front wall according to EN 12640 * N o t e: When using the front wall for securing the load, suitable lashing straps must be used for tensioning if the vehicle is operated without side panels and a rear flap Rear wall: * ATTENTION: Hinge mount for folding rear wall 600 mm as well as stake mount for folding corner stakes at the rear, however, the folding rear wall and corner stakes at the rear are OMITTED. Side wall: * VarioFix steel outer frame, 4 pairs of stake mounts for folding stakes on the outer frame (evenly distributed), WITHOUT folding stakes, pair of lashing brackets in the outer frame (according to EN 12640), permissible tensile force approx. 5,000 kg per ring. Side panels: * ATTENTION: Hinge mount for 5 pairs of side panels on the outer frame as well as side panel stop mounted on the corner posts at the front, however, the 5 pairs of side panels are OMITTED. Electrical system / Electronics: * Lamp carrier made of steel, arranged above the underrun protection * KÖGEL LUXIMA Premium package, consisting of: LED license plate lighting, LED marker lights and reflectors at the front, flashing LED side marker lights, Superseal and bayonet connectors for the lights * 2 LED outline lights with pendulum bracket * 2 multi-chamber tail lights *

Condition: used, Year of construction: 1959, shaft length 10 - 130 mm wire diameter 5 - 10 mm length of wire blank max. 165 mm capacity/output with closed mould, adjustable 125 /min capacity/output with open mould, adjustable 75 /min Weight 8,0 t dimensions of the machine (WxDxH) 2,1 x 3,7 x 1,5 m combined double-pressure cold header press for jaws and closed moulds maximum wire diameter for high tensile bolts und carriage bolts 8 mm maximum wire diameter for mild steel bolts and rivets 10 mm Hjdpfoyx Ihgsx Abpop wire diameter range 5 - 10 mm minimum and maximum shaft length 10 - 130 mm maximum length of wire blank 165 mm capacity/output with closed mould, adjustable - 125 St/min capacity/output with open mould - 75 St/min power requirement 11,0 kW mould dimensions - jaw dimensions 44 x 44 mm

Condition: used, Year of construction: 1966, shaft length 15 - 130 mm wire diameter 6 - 12 mm length of wire blank max. 170 mm capacity/output with closed mould, adjustable 100 /min capacity/output with open mould, adjustable 67 /min Weight 12,5 t dimensions of the machine (WxDxH) 2,3 x 4,0 x 1,6 m SPECIAL DEAL Hsdjv Sva Ejpfx Abpjp as is where is WITHOUT putting into operation / WITHOUT additional work free loaded to truck combined double-pressure cold header press for jaws and closed moulds maximum wire diameter for high tensile bolts und carriage bolts 10 mm maximum wire diameter for mild steel bolts and rivets 12 mm wire diameter range 6 - 12 mm minimum and maximum shaft length 15 - 130 mm maximum length of wire blank 170 mm capacity/output with closed mould, adjustable - 100 St/min capacity/output with open mould - 67 St/min power requirement 15,0 kW mould dimensions - jaw dimensions 54 x 54 mm

Condition: new, functionality: fully functional, machine/vehicle number: WFDFLT33801013475, empty load weight: 7,180 kg, maximum load weight: 28,820 kg, overall weight: 35,000 kg, axle configuration: 3 axles, loading space length: 13,650 mm, loading space width: 2,480 mm, total length: 13,850 mm, total width: 2,550 mm, suspension: air, tire size: 235/75 R17,5", tire condition: 100 %, color: silver, available in multiple units Fine-grained steel welded construction, kingpin plate with replaceable 2" kingpin, additional splash guard riveted to the underside as a sheet of metal, in the neck area above the rear axle of the semi-trailer and above the wheels on the vehicle, frame in reinforced design for vehicle loads up to the outer frame, outer frame with "Load-Lock profile" approximately every 400 mm for securing lashing straps, 10 pairs of lashing rings embedded in the top/outside of the outer frame, each rated at 10 tons, 24 tons. Two-stage support winch, single-side operation, with semi-circular lower part and straight connecting plate, with stroke compensation, folding rear support, support wedges with holder, aluminum side impact protection, steel under-ride protection, quarter panel fenders in front of and behind each axle, with additional sheet metal splash guard above the wheels, with anti-spray flaps according to EC regulations, 1 plastic toolbox, w=600 / h=425 / d=460 mm, lockable, container locking system, 4 pairs of locking recesses embedded in the floor for 2 x 20 ft or 1 x 40 ft containers, 4 pairs of container locking adapters, (additional transverse support required at the front and rear of the container, the container must rest evenly over its width in conjunction with the locks, transverse supports are not included in the scope of delivery), attachment rail for loading ramps at the rear extension over the entire width, rear extension mechanical, with hand crank, extendable by approximately 1,500 mm, lockable every 500 mm, including under-ride protection with lighting that can be extended, in the wheel well area with Lohr sheet metal, center with steel diamond plate, storage space for loading ramps integrated in the rear extension, usable only when the rear extension is extended by approximately 1000 mm, for transporting the ramps with the rear extension retracted - storage space for ramps in the FR, located to the right in front of the axles. 1 pair of ramps, 3,000 mm long, 300 mm wide, load-bearing capacity per pair 6,000 kg, electric cable winch, 24 volts, pulling force approximately 8165 kg, mounted centrally at the very front, operated with a wireless remote control, cable length 35 m x approximately 10 mm, with roller cable guide and removable guide rollers. Axles + Suspension: SAF/BPW drum brake axles, at the manufacturer's choice, air suspension, 1st axle automatic lift axle, additionally electrically operable from the truck, including forced lowering and starting aid. Braking System: 2-line pneumatic braking system, color-coded line routing for easy servicing, spring-loaded parking brake, 2 tamper-proof coupling heads at the front, EBS, electronic braking system with EBS socket at the front, without connection cable, with raising & lowering valve with quick vent, holding function in lowered position + auto-reset function, vehicle stability system, axle load recognition via EBS-CAN bus signal. Wheels and Tires: 235 / 75 R 17.5", manufacturer's choice, steel rims in twin arrangement. Hjdpfx Aoza Aiyebpop Electrical System: 24 volts, multi-chamber lights in LED, yellow LED lighting on the side, license plate lighting in LED, 2 white position lights at the front in LED, 2 white/red side marker lights at the rear in LED, 2 x 7-pole and 1 x 15-pole tamper-proof sockets at the front, 2 additional LED work lights at the rear, 1 rotating beacon with holder, switched via parking lights, 2 pairs of warning signs, double LED illuminated and

Condition: like new (used), Year of construction: 2017, functionality: fully functional, tank capacity: 40,000 l, usable tank capacity: 40,000 l, total height: 7,835 mm, outer diameter: 3,000 mm, overall weight: 3,500 kg, wall material: stainless steel, wall structure: single-walled, number of chambers: 1, manhole location: side, Equipment: cooling unit, 4 x 40 m³ Agitated Tank (Milk Tank) made of stainless steel, insulated, coolable Technical Data / Dimensions Available quantity: 4 Volume: approx. 40,000 liters Tank type: Agitated tank Condition: unused Food-grade: yes Design: vertical Internal diameter: approx. 2,950 mm External diameter: approx. 3,000 mm Cylindrical height: approx. 6,500 mm Overall height: approx. 7,810 mm Depth: approx. 1 mm Specific gravity of the medium: 1 ton/m³ Operating pressure: Non-pressurized Material / Construction Material, inner lining: Stainless steel Material: V2A-1.4301 (AISI 304) Internal welds ground smooth Hedpfxey Uciwe Abpop Heating / Cooling System Heating / cooling system available Number of cooling zones: 1 Bottom: Evaporator Cooling medium: Coolant / cooling gas Operating pressure: 18.6 bar Notes: Each tank has a cooling unit with direct evaporation (12 kW), which must be connected to the tank's cooling circuit. The unit was designed for cooling from 20°C to 4°C at an ambient temperature of 32°C. The cooling gas was evacuated during disassembly; the units will be supplied loose with the tanks. A specialized HVAC company is required for the connection and recommissioning of the cooling units and the cooling circuit of the tanks (not included in the purchase price)! Insulation Insulation available Insulation thickness: approx. 50 mm Insulation material: PU foam Material, insulation jacket: Aluminum Insulation jacket: screwed/riveted Notes: Cladding made of aluminum trapezoidal sheet, painted in RAL 9006 (white aluminum) Equipment Base design: Base ring / stand ring Quantity: 1 Mounting: fixed Top bottom: Conical bottom Bottom: Conical bottom Top: 1 x agitator connection incl. agitator 2 x lifting lugs 1 x snow guard 2 x connection for tank cleaning (CIP) 1 x inspection opening (approx. 400 mm) with closure 1 x threaded nozzle NW 65 for ventilation device Shell: 1 x manhole, oval (approx. 340 x 440 mm) 1 x sampling valve 1 x Rainbow cleaning system (automatic) incl. dosing pumps, control unit and control cabinet 1 x Insulated control room (attached) made of sandwich panels with lockable door (dimensions: approx. 1,940 x 1,640 x 810 mm) 1 x cleaning line Various connections for measuring and control technology Bottom: 1 x drain DN 80 Notes: The system consisting of 4 tanks is currently connected to each other with a central walkway. The walkway and the associated, two-section access ladder are available as an option. Agitator Agitator available Type of agitator: Paddle agitator Classification: Slow-speed Quantity: 1 Installation: from above Speed: 24 RPM Number of agitator levels: 3 Length of agitator elements: approx. 500 mm Bottom bearing for agitator shaft available Notes: Agitator designed for homogenizing milk fat (slow-rotating agitator motor with 24 revolutions / minute) Documentation Drawing

Condition: good (used), Hello, -The subject of sale is. Hjdpev I E Scefx Abpsp -Hang 87D 3P double-head riveter. -Manufacturer: Hang Germany. -Good condition. -The machine is used to rivet eyelets. -Two riveting heads, with adjustable spacing. -Cardboard thickness 0.2-4mm -Weight 570kg -380V power supply -Possible transport by freight forwarder (individual valuation)

Condition: excellent (used), 2 heads Rivets dimension 5,5mm Hsdepmarkopfx Abpsp

Condition: excellent (used), Year of construction: 2007, operating hours: 10 h, machine/vehicle number: 103414, High-performance automatic production line for ring binders. Sheet feeder (vacuum feeder), creasing station, gripping hole punching unit (finger hole eyeletting machine), double riveting station, operator control panel (Fanuc QuickPanel View), mechanical feeding unit, single riveting station, folding station. Cover height: 120 – 400 mm; cover width: 300 – 820 mm; material thickness: min. 1 mm – max. 3.5 mm; rivet spacing: 90 – 300 mm. Hsdpfxjx Apb Ho Abpsp

Condition: excellent (used), Year of construction: 2005, Hot water tank/heat storage tank made of V4A, upright Technical data / dimensions Available quantity: 1 Volume: approx. 164,000 liters Tank type: Storage tank Condition: used Suitable for food: yes Design: upright Diameter inside: approx. 3,900 mm External diameter: approx. 4,200 mm Cylindrical height: approx. 13,000 mm Total height: approx. 17,220 mm Weight: approx. 10,500 kg Specific weight of the medium: 1.0 to/m³ Operating pressure: unpressurized Wall thickness shell / cylinder: approx. 5.3 - 7 mm mm Ground clearance: approx. 1,800 mm Operating temperature: -10°C/+90°C degrees Celsius Material / properties Material inner jacket: V4A (1.4571) Material double jacket: Stainless steel Inner surface: 2B Weld seams ground on the inside Insulation Insulation available Insulation thickness: approx. 100 mm Insulation material: Mineral wool Insulating jacket material: Aluminum Insulating jacket: screwed/riveted Notes: Cone roof cladding: Stainless steel Cylinder cladding: Aluminum trapezoidal sheet Cone cladding: Aluminum smooth sheet Equipment Stand form: foot ring/stand frame Fastening: fixed Top shelf type: Conical base Bottom shelf type: Conical base Top floor: 1 x dome DN 200 with insulating cover 1 x flange DN 32 welded in the dome (CIP) Hodpfoqagl Hox Abpop 1 x DN 32 dome drainage 1 x DN 50 cable conduit 1 x overflow DN 150 2 x crane eye Jacket: 1 x inlet pipe DN 100 1 x filling pipe DN 100 4 x thermometer sleeve (ø 26 mm) with insulation box 1 x CIP line DN 32 1 x type plate 1 x access door (approx. 2,000 x 1,000 mm) 1 x DN 100 outlet nozzle Underbody: 1 x swivel cone DN 450, ending in smooth flange DN 100 Notes: Otherwise as per pictures and drawing documentation Drawing

Condition: used, Year of construction: 2015, functionality: fully functional, sheet thickness (max.): 2 mm, overall weight: 2,600 kg, total length: 1,000 mm, input voltage: 480 V, We offer this used Prinzing BEA2-S riveting and flanging machine, year of manufacture 2015. Type: BEA2-S Material thickness: 1.5 mm Length: 1000 mm Serial number: 1007 Year of manufacture: 2015 Weight: 2600 kg Voltage: 480 V Frequency: 60 Hz Power: 19.5 kW Current: 40 A The machine is already disassembled. Hjdpfey Ev Smsx Abpop If you have any questions or need further information, please don't hesitate to send us a message or call us.

Condition: excellent (used), Year of construction: 2011, KUKA KR 30-3 Robotic Welding Cell + Positioner + Fronius System Robot: KUKA KR 30-3 Controller: KRC2 Robot year of manufacture: 2011 Cell year of manufacture: 2011 2 robots CMT welding power sources: 2 Welding power source manufacturer: Fronius Type: Trans Synergic 4000 Wire feeder: VR7000CMT Remote control: RCU 5000i 2 torch cleaning stations Hsdpfx Aey Ia S Njbpep Rotary table 2 riveting stations Riveting station manufacturer: Böllhoff Microprocessor control: Proface TIG welding unit Manufacturer: Rehm Type: Tiger 170 DC Rotary table for assembly Storage racks Storage platforms

Condition: ready for operation (used), optionally in combination with an oval riveting machine of the same brand/age; see our other advertisement Hedpfxjx Nfhlo Abpep

Condition: ready for operation (used), In use from 1991 until it was last used and has been little prone to problems despite being a 1990s Chinese punching and riveting machine for oval eyelets. Hjdjx Nd U Depfx Abpep

Year of construction: 2006, condition: used, Torque assembly station, torque module, assembly device, torque wrench, torque wrench, torque wrench, rivet gun, rivet gun, blind rivet gun, Hedpfofw Rwmjx Abpsp -Drive: torque module for Hilok assembly -Torque: adjustable via touch screen -Number of press-in cylinders: 1 piece -Number of helical gears: 1 piece -Working platform: 800 x 500 mm -Travel: Y 400 mm, X 955 mm -Dimensions: 1555/1470/H2110 mm -Weight: 794 kg