Rivet header

Carlo Salvi RF/635/SV

Condition: used, Year of construction: 1985, functionality: fully functional, machine/vehicle number: M20L/9019, Offer Number: M20L/9019 Lodjx Edtcepfx Apmehi Machinetype: rivet header Make: Carlo Salvi Type: RF/635/SV Constr. year: 1985 diameter range: 3-6,35 mm shaft length under head: 65 mm cutting length: 87 mm output pieces/min: 360 Location: In our warehouse

Condition: new, Year of construction: 2024, shaft length under head: 80 mm, thread length: 55 mm, travel speed (max.): 480 mm/min, THREADING MACHINE E.W. MENN GW63 Refurbished as new acc. to CE Stand. Completely overhauled. New Guides, vibrator, new vibrating evacuation. New electrical system with Inverter and PLC M8x80/55 mm. Ledjt Uucajpfx Apmshi 480 ppm. Thread diameters (min./max.): 3 - 8 mm. Dies length: 115/130 mm. To be viewed and tested at HBR srl - Calolziocorte (LC)

Condition: used, Year of construction: 1985, functionality: fully functional, machine/vehicle number: M20I/9019, Offer Number: M20I/9019 Machinetype: rivet header Make: Carlo Salvi Type: RF/635/SV Constr. year: 1985 diameter range: 3-6,35 mm shaft length under head: 65 mm Lhsdpswzknujfx Apmji cutting length: 87 mm output pieces/min: 360 Location: Germany

Condition: used, Technical details: pressure: 100 t daylight dimension : table/slide up: 800 mm throat: 360 mm ram stroke: 500 mm ram speed - forward: 200 m/s ram speed - reverse: 200 m/s Table dimensions: 750 x 560 x 90 mm passage inside table: Ø 26 mm clamping surface ram: BxT: 530 x 400 mm mortise hole in ram: Ø 50 mm cylinder diameter: Ø 250 mm height over floor: 720 mm total power requirement: 17,0 kW weight of the machine ca.: 5,5 t dimension machine xH: 1,8 x 1,2 x 3,2 m Ljdpevc Ax Nofx Apmohi

Year of construction: 1988, condition: good (used), Carlo Salvi 1 die 2 blow Lhodpfxshrdmxe Apmei Model 780/SV Maximum Cutoff dia.mm: 6,35 Max. Cutoff length mm: 97 Max. K.O. length (die side) mm: 80 Max. Speed, pcs, per minute: 360

Condition: used, Thread Rolling Machine, Cold Rolling Machine, Thread Rolling Machine, Profile Rolling Machine Manufacturer: PEE-WEE Model: UPW 24 Serial No.: P07 Year of manufacture: 2007 Maximum rolling force: 24 tons Maximum tool diameter: 270 mm Roll spindle diameter: 69.85 mm Tool bore diameter: 70 mm (nominal diameter) Maximum tool/reception length: 180 mm Maximum workpiece diameter: 50 mm Hydraulic motor power: 3 kW Roll drive motor power: approx. 5.5 kW Electrical connection: 400 Volt, 50 Hz, 10 kW - Pivotable roll spindle for through-feed thread rolling - Roll spindle speed adjustable in 4 steps via gearbox shift - Hydraulic unit integrated in the machine base - Operating manual with electrical schematic Space requirements (L x W x H): 2,000 x 1,450 x 1,900 mm Weight: approx. 3 tons Very good condition Plunge Rolling: The thread rolling tools, having the same pitch as the workpiece, form the thread by penetrating the workpiece up to the nominal diameter. The maximum thread length is limited to the width of the rolling dies. Lhodpfeuz If Nex Apmsi Through-feed Rolling: Used when the thread length is greater than the width of the rolling dies. Through-feed tools are divided into three sections – entry, calibration, and exit. Knurling rolls have no pitch and are swiveled at the lead angle corresponding to that of the profile to be rolled. Lead angle rolls differ from knurling rolls by having a pitch in the profile. The sum of the lead angle and swivel angle results in the effective lead angle in the workpiece.

Condition: good (used), 1 used single-sided press Make: SACK & KIESSELBACH, year of construction: 1962,74 serial number 31900 Pressing force 630 t, stroke 310 mm Ljdpfx Apsul U Svemehi Installation height 320 mm Working height 1200 mm Drive power 10 KW

Condition: used, ORT RP18B overhauled Lhsdpfjuua H Rox Apmsi

Condition: used, Year of construction: 1986, pressure 160 t throat 360 mm stroke 500 mm feed down 200 mm/sec feed up 125 mm/sec max. distance table - ram 1000 mm table surface area 900 x 630 mm ram surface 850 x 450 mm clamping pivot 50 H7 / 85 mm total power requirement 17 kW weight of the machine ca. 7 t Ledpsv Rgwxofx Apmohi dimensions of the machine ca. BxTxH 1,25 x 2,2 x 3,45 m

Condition: excellent (used), Year of construction: 1972, functionality: fully functional, press force: max. 1.250 to. daylight: max. 480 mm width: 585 mm stroke: max. 355 mm weight: 9.000 Kg. Note: the press is been partly reconditioned by SACK & KIESSELBACH and the control system is been repalced. Lhodpewuutbsfx Apmsi