Used Mineral Wool for sale (295)

Condition: new, Year of construction: 2026, operating hours: 8 h, Very robust machine with high pressing force - is also suitable for producing a salable briquette quality * depending on the material. The large press cylinder and the 80 mm briquette make this possible. Our best-selling briquetting press series + Tried and tested, simple technology, for extremely low susceptibility to errors + 25 years of experience, further development and know-how + Several thousand machines in use with satisfied customers + Top price-performance ratio Surcharge for cooling unit + € 4.995 net, (can also be retrofitted later) * cools the pressing tongs (important from 3.5 hours) and the hydraulic oil * Cooling device recommended for regular use of more than 3.5 hours at a time. Briquette diameter: 80 mm Front bush: 125 mm Briquette stroke max .: 100 mm Briquette lift opt ​​.: 80 mm Output (depending on material): up to 200 kg / h * * depending on the bulk weight * based on a bulk weight of 200 kg per cubic meter Motor power: 9.2 kW 400 volts / 50 Hz / 3 phases Length: 2095 mm Width: 1300 mm Height: 1700 mm Weight: 1250 kg Oil volume: 220 liters Silo diameter: 1200 mm Silo content: approx. 1 qbm Pump: 75 liters Hydraulic pre-compressor Cooling pressing tongs option: yes, with special accessory coolable pressing tongs Hydraulic oil cooling option: yes Cooling of the pressing tongs and the hydraulic oil with cooling device (special accessory) Level monitoring option: yes Strand briquette option; yes (depending on material) Option of enlarged filling slide: yes, with special accessory enlarged filling slide CE compliant . Requirements for the raw material: - The moisture content (atro) must be between a minimum of 6 and a maximum of 18% - Chip length maximum 20 mm - Installation temperature: temperature-controlled room at at least + 5 ° C Lodpfxexfwdj Ahbehg - The loading must be free of metals and mineral impurities such as sand, stones, etc. This can result in damage to the pressing tools and / or increased wear

Condition: like new (used), functionality: fully functional, Year of construction: 2025, operating hours: 55 h, Machine with special rotor Available immediately Ledsx Af Rdspfx Ahbjhg Benefits: + Special rotor with reduced knife protrusion, suitable for hard and soft materials + 22 kW motor + Efficient square knives *For pallets: up to a maximum of 10 pallets per hour *Rate depends on screen size and material. Significantly higher throughput with smaller wood residues. Motor: 22 kW; 400 V - 50 Hz - 3 phase Screen: 15/20 mm or according to agreement (10 to 40 mm possible) Hydraulically operated pusher Current screen perforation (15/20 mm) *can be changed Suction connection Ø 200 mm Feed opening: 1000x1000 mm Dimensions: 2000x1800x1645 mm Sample image above: plant color may differ Weight: 1920 kg Standard scope of delivery includes: - Control cabinet with PLC control - Automatic star-delta start - High-speed hydraulics - Auto shut-off when rotor is idle - Speed 70–90 rpm for high throughput - Cycle control to prevent idle times - Performance-enhancing step control for the hydraulic pusher - Pertinax guides for hydraulic pusher - Vibration-damping machine feet - CE compliant The following options are available at an additional cost: - Increase shredder height by 30 cm (preparation for conveyor belt) + €2,480 net - Angled conveyor belt (discharge height approx. 220 cm) + €12,980 net - Overband magnet + €5,980 net - Control system for conveyor belt and overband magnet + €2,750 net (start and stop synced with shredder) - Enlarged hopper attachment 1500x1500 mm + €3,480 net Raw material requirements: - Moisture content (atro) must be below 25% - Feed must be free from metals and mineral contaminants. Tool damage and/or increased wear may result otherwise.

Condition: reconditioned (used), Year of construction: 2023, All wear parts new only 704 operating hours Special price for a low-hour demonstration unit Base machine: €29,990 net Optional extras (for an additional charge): - Cooling unit: €3,995 net - Emulsion tray: €3,990 net Lhsdpfx Asd N Dnhshbog The hydraulic briquetting presses of the MPP NEM series compact materials such as aluminum, copper, brass, bronze, graphite, and other non-ferrous metals into dimensionally stable cylindrical briquettes. These machines are distinguished by their robust construction, ensuring consistent briquette quality during continuous operation. The pressing process does not require any binding agents – compaction is achieved solely through hydraulic pressing force. Depending on material, the feedstock volume can be reduced by up to 90%. Throughput capacity: maximum 70 kg/h (depending on material) Briquette diameter: Ø 50 mm Motor: 5.5 kW 400 Volt / 50 Hz / 3-phase Pump: 40 liters Maximum briquette length: 50 mm Optimal briquette length: 40 mm Silo diameter: 1,000 mm Oil tank: 110 liters Dimensions: 1750 x 1130 x 1100 mm (L x W x H) Weight: 950 kg Hydraulic pre-compaction via slide Main press cylinder Vertical cylinder Fill level sensor: yes Feed material requirements: - Max. chip length: 15 mm - Installation room temperature: heated space, at least +5°C - Max. load on agitator: 150 kg - Feed material must be free from magnetic metals and mineral contaminants such as sand, stones, etc. Damage to pressing tools and/or increased wear may otherwise occur.

Condition: new, Year of construction: 2026, Production time of the machine approx. 3.5 months Very robust machine with high pressing force - is also suitable for producing a saleable briquette quality *depending on the material. The large press cylinder and the 65 mm briquette make this possible. Our best-selling briquetting press series + Tried and tested, simple technology, for extremely low susceptibility to faults + 25 years of experience, further development and know-how + Several thousand machines in use with satisfied customers + Good price-performance ratio Options: Surcharge for cooling unit + € 3,995 net, (can also be retrofitted later) * cools the press tongs (important from 3.5 hours) and the hydraulic oil * Cooling unit recommended for regular operation of more than 3.5 hours at a time. Large pre-compressor chamber + € 1,975 net recommended for light starting materials such as wood shavings Product code: 84793010 Briquette diameter: 65 mm Front bush: 65 mm Briquette stroke max.: 50 mm Briquette stroke opt.: 50 mm Output (depending on material): up to 110 kg/h* approx. 87 kg/h in the last test. *depending on the bulk density *based on a bulk weight of 200 kg per cubic meter . Motor power: 5.5 kW 400 Volt / 50 Hz / 3-phase Lodpfoffh Atox Ahbjhg Length: 1925 mm Width: 1100 mm Height: 1500 mm Weight: 800 kg Oil volume: 110 liters Silo diameter: 1000 mm Silo capacity: approx. 0.7 qbm Pump: 37 liters Hydraulic pre-compressor Cooling press tongs option: yes, with special accessory Coolable press tongs Cooling of the pressing tongs via water tank (to be procured on site) Hydraulic oil cooling option: yes Fill level monitoring option: yes Briquette option: yes (depending on material) CE compliant . Requirements for the raw material: - The moisture content (atro) must be between a minimum of 6 and a maximum of 18 % - Chip length maximum 15 mm - Installation temperature: tempered room at a minimum of +5°C - The feed must be free of metals and mineral impurities such as sand, stones, etc. Damage to the pressing tools and / or increased wear may result

Condition: good (used), Used machine, good condition. Delivery time appr. 16 weeks after ordering Basic machine starts at 139.700 € net *Options at additional cost, see below Briquetting press e.g. for wood dust, spelled husks, activity material (e.g. for pigs to play and nibble around), animal feed, lucerne or wood shavings. *Optionally, short briquette tablets can be made Technical specifications: Throughput capacity up to a maximum of 750 kg/h (depending on the material) (e.g. sawdust with a bulk density of 250 kg/qbm) An exact statement about the throughput is only possible after a test with your material. Can vary greatly depending on the bulk density of the starting material. Goods tariff number: 84793010 Briquette Ø 65 mm including 2 m press channel Engine power main engine 37 kw Feed screw geared motor 2.2 kw Compressor screw 5.5 kw Hydraulic pump motor 0.37 kw Total connection value: approx. 47 kW Control panel with plain text display for operating states and utilization indicator for the main drive and feed screws PLC control with operating hours counter in the control cabinet Machine has CE mark Automatic start-stop function Dimensions 3100x860x1800 mm lxwxh Weight 3800kg Options at extra cost: Temperature control unit for the pressing tools to maintain the temperature for optimal briquette quality. Temperature controller for pump, cooling unit, fan, pressostat Wired ready for connection - absolutely necessary for operation including the corresponding control + €7,850 net guillotine or pill crusher, Lsdpofmqq Eofx Ahbehg for cutting the briquettes to length + €6,900 net Necessary for compressed air connection! Silo for MAP series + €19,940 net - Storage silo above the machine - Content approx. 6 sqm, stable steel construction with agitator discharge and level indicator. Transport line / cooling section (nominal value: 4x2m) each 2 meters 990 euros net Control System 4.995 € net Assembly / commissioning (nominal value approx. 2-3 days on site) according to expenditure on proof against separate calculation. The following sentences apply: Service technician/mechatronics technician per hour of assembly and travel: €129.00 Overtime: 25% surcharge 50% surcharge for each Saturday and night hour 100% surcharge for each Sunday and holiday hour Release per mechanic per day: depends on the country Per car and van and driven kilometer: 0.98 € / km Arrival and accommodation against receipt or flat rate billing at the expense of the client. . Test with the respective customer material: (by arrangement, up to a maximum of 750 kg) - 1,970 € net . Raw material requirements: - The moisture content (atro) must be between at least 6 and a maximum of 15% - Maximum chip length 18 mm - Installation temperature: room with a temperature of at least +5°C - The charge must be free of metals and mineral impurities. This can result in damage to the pressing tools and/or increased wear

Condition: as good as new (ex-display), Year of construction: 2025, Special price for our demonstration machine Another machine, available now (ex works in Neckartailfingen) Approx. 8 operating hours. Suitable for shredding all types of leftover wood and also pallet sections. The pallet would need to be prepared with a jigsaw or chainsaw so that it fits vertically into the hopper - see Figure 2. Ideally, it would be approximately 40x20x20 cm so that the wood can lie flat on the slider floor. This is where the machine works most effectively. A hydraulic slider runs at the bottom of the shredder, which pushes the wood against the rotor depending on the load. The material is shredded until it passes through the screen basket. Throughput up to 200 kg per hour *depending on the screen and how well the material is prepared. *Conveyor belt and overhead magnet available at an additional cost. + Powerful 18.5 kW motor, + Concave blades, + Large high-performance gearbox, + Special, load-dependent slide control, Customs tariff number: 84659600 Motor: 18.5 kW; 400 V - 50 Hz - 3 phase Blades: 15, multi-rotatable Option: double row of blades + €995 net Rotor diameter: 260 mm Control: Siemens S7-1200 PLC Cutter opening: 630 x 820 mm Filling volume: approx. 0.6 m³ Hydraulic slide gate Screen perforation of your choice (10 - 30 mm) Suction nozzle diameter: 160 mm Weight: approx. 1,300 kg (depending on accessories) Dimensions (L x W x H): approx. 1,737 x 1,167 x 1,650 mm Moisture content: 30% dry Included as standard: - V-rotor for maximum throughput - Control cabinet with Siemens PLC control - Automatic star/delta start-up - Fast hydraulics - Auto. OFF when the rotor is idling - Speed 70-90 rpm for high throughput - Cyclic control to avoid idle times - Performance-enhancing step control of the hydraulic slide - Pertinax guides for the hydraulic slide - Vibration-damping machine feet - CE compliant. - MADE IN GERMANY . Shredder options: - Raise shredder by 30 cm (prepared for conveyor belt) +€2,080 net - Articulated conveyor belt +€8,770 net Horizontal section: 1,200 mm Rising section: 2,500 mm Angle: adjustable from 0-60 degrees Discharge height: approx. 2,000 mm + - 100 mm Lhsdpsdwktkofx Ahbjg - Overbelt magnet +€5,980 net - Conveyor belt and overbelt magnet control +€2,750 net (Start and stop synchronized with the shredder) - Extend hopper +€940 net - Eco-rings: +€1,980 net (recommended for more than 15% hardwood) - Special scraper +€990 net (recommended for veneer or paper) - Double Knife series + €995 net . Raw material requirements: - The moisture content (dry) must be below 30% - Metals and mineral contaminants such as sand, stones, etc. lead to increased wear.

Condition: new, Year of construction: 2026, The ideal machine for shredding softwood. Motor: 11/15 kW; 400 V - 50 Hz - 3 ph, Rotor diameter: 260 mm, Hydraulically actuated pusher Screen perforation to choice (12 - 40 mm) Extraction port Ø 160 mm Weight approx. 1,100 kg Dimensions (LxWxH) approx. 1805 x 1118 x 1650 mm Colour: blue / grey Requirements for raw material: - Moisture content (atro) must be below 30% - Metal and mineral contaminants such as sand, stones, etc. lead to increased wear. Lhedswzarcspfx Ahbeg We are pleased to offer a free test with your material. You are welcome to visit us in Neckartailfingen for this purpose. Alternatively, you can send us your material by freight and we will document the test with photos and videos.

Condition: as good as new (ex-display), Year of construction: 2025, showroom machine machine available Advantages: + special rotor with reduced knife protrusion + Motor 22 kW + effective square knife * for pallets: up to 10 pallets per hour * depending on the sieve and material. With smaller residual wood, significantly more. Engine: 22 kW; 400 V - 50 Hz - 3 ph, Sieve: 15/20 mm hydraulically operated slide Current screen perforation (15/20 mm) * can be exchanged Extraction nozzle Ø 200 mm. Feed opening 1000x1000 mm Lhjdpjdv Eu Hefx Ahbsg Dimensions: 2000x1800x1645mm Example image above: The color of the system may vary Weight: 1920 kg. Included as standard: - Control cabinet with PLC control - automatic star / delta start - fast hydraulics - automobile. OFF when the rotor is idling - Speed ​​70-90 rpm for high throughput - cycle control to avoid idle times, - performance-increasing step control of the hydraulic slide, - Pertinax guides for hydraulic slides, - vibration-damping machine feet, - CE conform. The following options are available at an additional cost: - Additional row of knives + € 2,790 - segment bottom + € 6,890 (recommended for materials with a wall thickness thinner than 3 mm) - Special K-rotor storage + € 3,480 If necessary, consider shredding plastic with sieves smaller than 15 mm or with a lot of fines. If the bearings are lubricated with grease every approx. 4 weeks in operation, this is not necessary) - Raise the shredder by 30 cm (preparation for conveyor belt) + € 2.480 net - Angled conveyor belt (discharge height approx. 220 cm) + € 12.980 net - Overbelt magnet + € 5.980 net - Control conveyor belt and overbelt magnet + € 2.750 net (Start and stop synchronized with the hacker) - Exhibition hopper 1500x1500 mm + € 3.480 net Requirements for the raw material: - The moisture content (atro) must be below 30% - The loading must be free of metals and mineral impurities. This can result in damage to the tools and / or increased wear

Condition: new, Year of construction: 2026, Single-shaft shredder MRZ 530 Included: + Profile rotor for increased throughput Options: Double knife row + €895 net Veneer and paper stripper + €970 net * recommended for extremely thin materials with a thickness less than 3 mm Our mütek single-shaft shredder MRZ 530 processes a wide variety of materials such as all types of wood residues, softwood, chipboard and MDF, pallets, construction timber, demolition wood, carpets, cables, paper, cardboard, and plastics. The machine is characterized by its robust design, ensuring consistent quality in continuous operation. We are pleased to offer you a free test with your material. You are welcome to visit us in Neckartailfingen for this purpose. Alternatively, you can send us your material via freight and we will document the test with pictures and videos. Machine data: Motor: 15 kW; 400 V - 50 Hz - 3 phase Knives: multiple reversible Rotor diameter: 260 mm Control: Siemens S7-1200 PLC Hopper (mm): 510 x 810 mm Hopper volume approx. 0.4 m³ Throughput: 1 - 5 hopper fillings/hour Hydraulically operated pusher Screen perforation as desired (10 - 40 mm) Extraction nozzle Ø 160 mm Weight approx. 1,000 kg Dimensions approx. 1550 x 1100 x 1640 mm Moisture content of raw material: must be below 30% a.d. Standard features included: • Fast hydraulics • Profile rotor • Control cabinet with Siemens PLC control • Automatic star-delta start • Automatic shut-off in case of rotor idle • Removable extraction channel • Speed 70 - 100 rpm for higher throughput • Cycle control to prevent idle time • Performance-enhancing step control for hydraulic pusher • Stable guides for hydraulic pusher Additional shredder options: - Raise shredder by 30 cm (preparation for conveyor belt) + €1,980 net - Angled conveyor belt + €8,770 net Horizontal section: 1200 mm Inclined section: 2500 mm Angle: adjustable 0-60 degrees Ledpfxsd Db N Io Ahbshg Discharge height: approx. 2000 mm ± 100 mm - Overband magnet + €5,980 net - Control for conveyor belt and overband magnet + €2,750 net (start and stop synchronized with the shredder) Requirements for input/raw material: - Moisture content (a.d.) must be below 30% - Metals and mineral impurities such as sand, stones, etc., lead to increased wear

Condition: new, Year of construction: 2026, Delivery time approx. 3-4 months MRZ 830 Shredder Custom tariff number: 84659600 Feed opening 800 x 1000 mm Motor: 18.5/22 kW; 400 V - 50 Hz - 3 ph Blades: multi-rotatable Hydraulically operated slider Screen perforation of your choice (10 - 40 mm) Suction nozzle Ø 200 mm Weight approx. 1,600 kg Dimensions (L x W x H) approx. 2,290 x 1,420 x 1,750 mm Turbo clutch Included as standard: - Automatic star/delta start-up - Fast hydraulics - Auto. OFF when the rotor is idle - Speed 70-90 rpm for high throughput - Cycle control to avoid idle times - Performance-enhancing step control of the hydraulic slide - Pertinax guides for the hydraulic slide - Vibration-damping machine feet - CE compliant . The shredder is designed for shredding natural wood, particle board, and MDF, as well as other materials after testing and approval by the manufacturer. Additional shredder options: - Raise shredder by 30 cm (prepared for conveyor belt) + €2,140 net - Articulated conveyor belt + €8,770 net Horizontal section: 1,200 mm Rising section: 2,500 mm Angle: adjustable from 0-60 degrees Discharge height: approx. 2,000 mm + - 100 mm - Overbelt magnet + €5,980 net Lhsdpfx Ajd Dgw Ujhbog - Conveyor belt and overbelt magnet control + €2,750 net (Start and stop synchronized with the shredder) Raw material requirements: - Moisture content (dry) must be below 30% - Installation temperature: temperature-controlled room at least +5°C - Metals and mineral contaminants such as sand, stones, etc. lead to increased wear

Condition: new, Year of construction: 2025, The ideal machine for shredding hardwood and softwood Another machine now available (ex-works Neckartailfingen). Motor: 18.5 kW; 400 V - 50 Hz - 3 ph, Blades: 14+2 pieces, 40x40mm, reversible multiple times, Rotor diameter: 260 mm, Control system: Omron PLC, Cutting chamber opening: 600 x 800 mm, Hopper volume approx. 0.6 cbm, Hydraulically operated pusher Screen perforation of your choice (12 - 40mm) Extraction socket Ø 160 mm Weight approx. 1,300 kg Dimensions (LxWxH) approx. 1737 x 1167 x 1650 mm The following options are available at an additional cost: - Additional row of knives + €1,990 net (28 instead of 14) - Surcharge for segmented floor, 4-sided + €2,170 net (prevents the pusher from jamming. Recommended for materials with a thickness of less than 3 mm) - Raise shredder by 30 cm (preparation for conveyor belt) + €1,980 net - Angled conveyor belt (discharge height approx. 220 cm) + €8,770 net - Overband magnet + €5,980 net - Control system for the conveyor belt and overband magnet + €2,750 net (start and stop synchronized with the shredder) - Special bearing + €1,540 net (rarely required. Closed, even more robust rotor bearing. May be considered for screens smaller than 15 mm or high fine content. Not necessary if bearings are greased approximately every 2 weeks in operation) Ljdpfed E R D Sex Ahbohg Requirements for raw material: - The moisture content (atro) must be below 30% - Metals and mineral contaminants such as sand, stones, etc. increase wear. We are happy to offer a free test with your material. We invite you to visit us in Neckartailfingen for this purpose. Alternatively, you can send us your material via freight company and we will document the test with photos and videos.

Condition: new, Year of construction: 2024, production time appr. 4 months * for suction perception, see picture 4 and 5 Tariff number: 84659600 Main motor: 55 kW; 400 V - 50 Hz - 3 ph including turbo coupling, Lodpfx Aed Hkqhjhbjhg Hydraulic motor: 2.2 kW, 400 V - 50 Hz - 3ph Knife: 76 pieces, rotatable Knife size: 35 x 35 x 20 mm Rotor diameter: 360 mm Control: PLC Siemens S7-1200 Funnel opening approx. 1530 x 1235 mm Hopper volume approx. 2.5 square meters hydraulically operated slide Screen perforation: 10 - 30 mm Extraction nozzle Ø 200 mm Weight approx. 4,500 kg Dimensions (lxwxh) approx. 2765 x 2520 x 1730 mm Turbo coupling Included as standard: - V-rotor for other throughput - 2nd row of knives on the rotor - Control cabinet with Siemens PLC control - automatic star / delta start - fast hydraulics - Automobile. OFF when the rotor is idling - Speed ​​70-90 rpm for high throughput - Clock control to avoid idle times - Performance-increasing step control of the hydraulic slide - Pertinax guides for hydraulic slides - anti-vibration machine feet - CE conformity The shredder is for shredding natural wood, chipboard and MDF board other materials after testing and approval by the manufacturer Recognition from the raw material: - The moisture content (atro) must be below 30% - Metals and mineral impurities such as sand, stones, etc. Interests to interests wear

Condition: as good as new (ex-display), Year of construction: 2025, Machine for sale at a special price Another machine, available immediately (ex works Neckartailfingen) * Including 1 year warranty. Your advantages: + Very robust, simple technology + Top price-performance ratio + Suitable for continuous operation + Long-standing, well-functioning / established machine Including control cabinet with timer operation Press is switched on manually and then runs until the time set on the timer (e.g. 4 hours) has elapsed. Then the press switches off. Technical data: Lhsdjd Nnwlspfx Ahbsg Briquette dimensions: approx. 30 x 30 mm (square), Briquette length: 5-40 mm *depending on material Throughput capacity: up to a maximum of 20 kg/h. *depending on material Machine dimensions approx. 137 x 75 x 148 cm (length x width x height), Weight of the machine: approx. 250 kg, Capacity of the silo: approx. 250 liters, Motor: 2.2 kW, 400 V - 50 Hz, Noise emission: 62 dB, Raw material requirements: -Wood chips and dust smaller than 15 mm in length -Moisture content less than 18 % ATRO -Sand, stones, metals and minerals increase wear --- Options at extra charge: --Timer function + 490 € net Machine is started manually and switches off automatically after a set time X. -Level indicator for automatic operation + 1450 € net Press starts and then stops automatically * NEW !!! Also available in 230 Volt, Motor then 3 kW instead of 2.2 kW, Surcharge + 890 € net (delivery time then approx. 8 weeks) - Special pressing units + 2.950 € net ---

Condition: like new (used), Year of construction: 2024, operating hours: 29 h, *one machine is ready for delivery and ready produced Press can only be supplied with a system component such as a chipper, cutting mill, hammer mill, screw conveyor, conveyor belt with overbelt magnet or suction RUF briquetting press for rectangular briquettes Very robust and established machine The ideal machine for professional, industrial briquette sellers. Classic type - throughput up to 425 kg / h * depending on the material Options for an extra charge: Plant construction / mütek system technology: - mütek shredder MRZ shredding technology - conveyor belts - Overbelt magnets - Extraction systems, optionally with rotary valve - screw conveyors - silos - Control links of all kinds - semi-automatic packaging technology Press: - Packing table with drawer - Top-mounted silo with discharge Your advantages: Lhodpfx Asfhql Tshbjg Most important point: + Very established, well-engineered die press thanks to 25 years of experience. The difficulty and the know-how lies in the detail. For example, valves and cylinder seals of the highest quality. + 24h operation possible + Longevity + Low maintenance costs + Compact structure + High energy efficiency thanks to innovative hydraulics Technical data briquetting press: Throughput: up to 425 kg / h * * depending on the bulk weight of your raw material * based on a bulk weight of 200 kg per cubic meter Detailed information after a successful test with your material. If no test material is made available to us, we cannot make any statements about the briquette quality and throughput. Briquette dimensions: 150 x 60 mm Briquette length: 40 to 105 mm (adjustable) Hydraulic pre-compressor Main hydraulic compressor Pressing pressure: up to approx. 1700 kg / cm² Hydraulic system with 260 liter oil tank Pump motor: 30 kW / 400V / 50Hz / 3 ph Manual operation of all cylinders "Dustproof" switch cabinet with PLC control and touch display Total power consumption of the briquette press: approx. 33 KW Muxzr8 Requirements for the raw material: - The moisture content (atro) must be between a minimum of 6 and a maximum of 15% - Maximum chip length: 20 x 2 x 2 mm - temperature where machine is placed + 8 degrees - The loading must be free of metals and mineral impurities such as sand, stones, etc. This can result in damage to the pressing tools and / or increased wear.

Condition: as good as new (ex-display), Year of construction: 2023, The ideal machine for shredding cables including optimized cutting geometry approx. 9 operating hours Motor: 18.5 kW; 400 V - 50 Hz - 3 ph, Blades: 14 pieces, 40x40mm, multi-rotatable, Rotor diameter: 260 mm, Control: Omron SPS, Cutting unit opening 600 x 800 mm, hopper volume approx. 0.6 qbm, hydraulically operated pusher Screen perforation of your choice (15 - 40 mm) Suction nozzle Ø 160 mm Weight approx. 1,300 kg Dimensions (lxwxh) approx. 1737 x 1167 x 1650 mm The following options are available at extra cost: - Double row of knives + 995 € net (28 instead of 14) - Surcharge for 4-sided segment base + € 3,750 net (prevents blocking of the pusher. Recommended for shredding plastics, paper, veneer with a thickness of less than 3 mm). - Raise shredder by 30 cm (preparation for conveyor belt) +1,980 € net - Angled conveyor belt (discharge height approx. 220 cm) + €8,770 net Ljdegmfa Aepfx Ahbjhg - Overbelt magnet + € 5,980 net - Conveyor belt and overbelt magnet control + € 2,750 net (start and stop synchronized with the chipper) Bea9ia3l27 Requirements for the raw material: - Mineral impurities such as sand, stones, etc. lead to increased wear. We are happy to carry out a free test with your material and invite you to visit us in Neckartailfingen. It is also possible for you to send us your material by freight forwarder and we will document the test with pictures and videos.

Condition: good (used), Refurbished machine *Options at additional cost, see below with a full 1 year warranty Ready for delivery approx. 16 weeks after ordering Technical specifications: Throughput up to 1200 kg / h depending on the material (e.g. sawdust with a bulk weight of 150/180 kg / qbm) Briquette Ø 75 mm including 2 m press channel Main motor power 45 kW Feed screw gear motor 2 x 2.2 kw Compressor screw 2 x 5.5 kw Distribution auger 2.2 kw Hydraulic pump motor 0.37 kW Total connected load 65 KW Control panel with plain text display for operating states and utilization display for main drive and feed screws PLC control Siemens S7 / 300 with operating hours counter in the control cabinet Machine hat CE mark Automatic start / stop function of the machine Dimensions 3100x860x1800 mm lxwxh Weight 4500 kg Options: Lhjdj E Dquopfx Ahbsg -Silo for MAP series Storage silo above the machine - Contents approx. 6 square meters, stable steel construction with agitator discharge and level indicator. 19,700 € net plus VAT. *only possible for one presse MAP 1200 below the silo if you need to place two machines MAP 1200 below one silo it needs to be build completely different. the price for this silo is 37.900 € net -Temperature control device for the pressing tools to maintain the temperature for optimal briquette size. Temperature controller for pump, cooling unit, fan, pressostat Wired ready for connection - must be left for operation including corresponding control € 7.850 net Oil heater 1.950 € net -Guillotine, to cut the briquettes to length Create a compressed air connection on site € 6,940 net plus VAT -Transport line / cooling section (nominal value: 4x2m) 990 euros net per 2 meters - Control System 4.995 € net Assembly / commissioning (nominal value approx. 2-3 days on site to install one press) based on effort and upon proof against separate invoice. The following sentences apply: Service technician/mechatronics technician per assembly and hour of travel: €129.00 Overtime: 25% surcharge 50% surcharge per Saturday and night hour 100% surcharge for every Sunday and public holiday hour Release per fitter per day: country dependent Per car, van and driving kilometer: €0.98 / km Arrival and overnight stay against receipt or flat rate bill at the client's expense. . Test with the respective customer material: (up to a maximum of 750 kg) - €1,970 net flat rate --- Recognition from the raw material: - The moisture content must be between a minimum of 6 and a maximum of 18% - Maximum span 20 mm - Excessive temperature: temperate room at at least + 5 ° C. - The loading must be free of metals and mineral impurities. This and the pressing tools and / or responsible wear can be the result

Condition: used, Shredding Machine MGZ 1330, 37 kW Operating hours: 275 Included: - Second knife row - Fast hydraulics for increased throughput - Preparation for conveyor belt Optional: - Conveyor belt with automatic metal separator Your advantages: + Extremely large cutting chamber opening; top: 1300x1200mm + Special rotor suitable for both hardwood and softwood + Energy-efficient and powerful, 37 kW start-up power Technical data: Feed opening, top (mm): 1,300 x 1,200 Hopper capacity (cbm): 1.6 m³ Rotor diameter (mm): 368 Rotor speed (rpm): 65 - 125 Power requirement (kW): 37 Screen hole size (mm): configurable Lhsdpfx Ahex Tfdhebjg Tools: 37/70 knives Extraction connection diameter (mm): 200 mm Dimensions: 2430x2410x1735 mm (LxWxH) Weight (approx. kg): 3,500 --- Feedstock requirements: - The moisture content (atro) must be below 20% - The feed material must be free of metals and mineral contamination. Damage to the tools and/or increased wear may result.

Condition: good (used), Year of construction: 2025, Requirements: - Material must be free-flowing (less than 18 mm) - Material must be pure, with ash content below 1% ATRO Caution concerning: sand, stones, and mineral content - Material is compacted by pressing tongs - Material must be dry, maximum 15% ATRO New: Innovative combination of briquette and pellet Optional upgrades available: Plant engineering / mütek Systemtechnik: - mütek Shredder MRZ size-reduction technology - Conveyor belts - Overband magnets - Extraction systems, optionally with rotary valve - Screw conveyors - Silos - All types of control system integration - Semi-automatic packaging solutions + 24h operation possible + Compact design + High energy efficiency thanks to innovative hydraulics + Achievable briquette density of up to ≥ 1 kg/l *Details after testing Functionality: The machine features a silo with agitator. Each of the four corners of the storage silo contains a vertical screw which compacts the material downward into the press chamber. The machine operates with two cylinders, each pressing in both directions (either as the cylinder moves forward or backward). This produces four briquette outlets, each generating six individual briquettes. *Ideal for automatic feeding of the heating boiler Format: Ø 30 mm Throughput capacity: up to 310 kg/h maximum Motor power: approx. 27 kW (total) Dimensions: 3.1 x 2.3 x 2.2 m Weight: 3.55 tons Your advantages: Compact briquette/pellet format enables fuel feeding of industrial firing plants via screw conveyor Fully automatic 24h operation possible High energy efficiency Briquettes/pellets with consistently high quality and density For automatic feeding into industrial combustion systems Small to medium quantities of wood chips generated in various processing industries (especially wood, biomass, etc.) can be efficiently compacted. The small Ø 30mm format represents an attractive alternative. Unlike our conventional briquettes, these can be fed automatically into industrial combustion systems. Lhjdpfx Ahjfbb Arjbsg In addition to wood, a wide variety of other materials can also be processed without issue (various types of biomass and agricultural residues).

Condition: used, Year of construction: 2010, Overview  The Octopus film winder was built in Finland in 2010. The machine was in use at a mineral water company until recently and is already dismantled and immediately available.   Technical details   Speed of the motion sequences  Ring up/down 0.15 m/s  Ring rotation 18 rpm  Film insertion 4.5 m/s  Film: LLDE pre-stretched  Hold-down device  Pallet dimensions   ¼ EURO,  ½ EURO,   EURO,   1200 × 1000,   Max. height 2400 mm,   Min. height approx. 50 cm depending on the system settings  Dimensions  Length 2850 mm   Width 2150 mm   Height 3140 mm   Weight 1050 kg   Voltage: 3 × 400 VAC 50 Hz +N+earth  Air pressure 6 bar, 9 l/operating cycle  Lhedpouca Amjfx Ahbeg

Condition: used, maximum load weight: 31,420 kg, overall weight: 39,000 kg, axle configuration: 3 axles, first registration: 05/2023, next inspection (TÜV): 05/2026, loading space volume: 34 m³, total width: 2,550 mm, total height: 3,685 mm, Year of construction: 2023, Equipment: ABS, Kässbohrer Tank Semi-Trailer STC 34 Code L4BH Chemical First Registration Ø Unladen weight: 7,580 kg Ø Stainless steel chassis, polished to a high gloss Ø BPW axles with large disc brakes, 430 mm Ø 1st axle is a lift axle Lhodpex Rtafjfx Ahbeg Ø Crank support legs, steel, full-load capable Ø 6 tires, size 385/65 R 22.5 Ø Aluminum rims, ALCOA Dura-Bright, high gloss Ø WABCO trailer EBS with RSS (Roll Stability Support) Ø Tank: 34,000 liters, made of stainless steel 1.4571 (AISI 316 Ti) Ø Operating pressure 3.0 bar / test pressure 4.0 bar Ø Insulation: 100 mm glass wool Ø Single compartment with 4 baffle plates Ø 5 manhole covers: 3x DN500 and 2x DN350 Ø 1 vent valve by Fort Vale Ø 1 safety valve Ø 1 check valve Ø Air line on right side, DN 50, with TW 50 connection at front right Ø Heating preparation, 4-channel hot water Ø 1 discharge outlet, DN 100 uninsulated, with sampling tap at rear right and TW 80 coupling Ø 1 emptying (cleaning) system Ø Pneumatic bottom valve Ø Hose tubes left and right, DN 150, approx. 6 m long RENTING is the new BUYING – also available from us as a full-service rental.

Condition: used, -Dimensions (LxWxH): 1420x2200x2200 mm -Serial number: 8801680 -Reference number: 7367165 -Baking surface: 5.3 m² -Stone slab dimensions: 801x1230 mm -Year: 2005 -Number of decks: 5 -Maximum temperature: 300°C -Voltage: 400V -Heating power: 53.6 kW -Weight: 1064 kg Ljdpsy Icknefx Ahbehg -Refurbished equipment: Equipment is prepared upon order; lead and turnaround times are specified at that moment (please request pricing after refurbishment) -Front panel with brushed stainless steel extraction hood -Heavy refractory cement baking soles, 20 mm thick -Stainless steel armoured electric heating elements -1 independent pressure relief damper per deck -1 independent steam generator per deck -Glazing treated to reduce heat loss -Steam system and column always on the same side -Equipped with a steam extractor for the hood -Insulated with cross-laid rock wool panels -Electrical bundles with high-temperature silicone cables

Condition: used, -Dimensions: 1420x2600x2200mm -Stone size: 801x1630mm -Model: Omega5.163 -5 decks -Serial number: 8118337 -Year: 2003 -Baking surface: 6.6m² -Temperature: 300°C -Voltage: 400V -Power: 30kW -Weight: 1800kg -Refurbished equipment: The equipment is prepared upon order; lead times for collection and return are agreed upon at the time of ordering (please request the price after revision) -Front with brushed stainless steel hood -Solid refractory cement baking stones, 20mm thick -Stainless steel armoured electric heating elements -1 independent pressure relief valve per deck -1 independent steam generator per deck -Treated glazing to reduce heat loss Ledpfxsy H Ebmo Ahbehg -Steam unit and column always on the same side -Equipped with a steam extractor for the hood -Insulated with cross-laid rock wool panels -Wiring looms made of high-temperature silicone cables

Condition: used, -Dimensions: 1620x2225x2300 mm -Serial no.: 12026399 -Model: Omega 4 Lhsdpoy H D A Aefx Ahbog -Slab size: 801x1840 mm -Year: 2007 -Baking surface: 5.9 m² -Max. temperature: 300 °C -Integrated loader/lifter -Voltage: 400V -Power: 27 kW -Weight: 1590 kg -Overhauled equipment: equipment is prepared upon order; collection and return deadlines are agreed at this time (please request price after overhaul) -Front panel with brushed stainless steel hood -Heavy-duty refractory cement baking decks, 20 mm thick -Stainless steel sheathed electric heating elements -1 independent relief damper per deck -1 independent steam generator per deck -Thermal treated glass to reduce heat loss -Steam unit and column always on the same side -Equipped with steam extractor for the hood -Insulation by cross-laid rock wool panels -High-temperature silicone cable wiring harnesses

Condition: used, mileage: 152,000 km, power: 90 kW (122.37 HP), first registration: 01/2021, fuel type: diesel, overall weight: 3,020 kg, color: black, gearing type: mechanical, emission class: euro6, Equipment: ABS, air conditioning, central locking, electronic stability program (ESP), navigation system, soot filter, Special equipment: Tow bar (removable ball head), with tools, audio navigation system Multimedia Navi Pro, flooring: passenger/cargo area wood (with anti-slip profile), DAB tuner (digital radio reception), metallic/mineral effect paintwork, front and rear parking pilot system, spare wheel with matching tires, reversing camera with 180° surround view Additional equipment: 2nd row seats with bench, driver/passenger airbags, on-board computer, brake assist, driver assistance system: Hill Start Assist (HSA), rear wing doors without windows, body type: panel van, vehicle length variant L3, head airbag system, adjustable steering column (steering wheel), headlight range adjustment, engine 2.0 litre – 90 kW diesel, wheelbase 3275 mm, low emissions according to Euro 6d-TEMP standard, sliding door on the right, SCR system (AdBlue technology), fixed rear side windows, visibility package, steel wheels 7x16, start/stop system, 12V socket in boot/cargo area, 12V socket in center console, partial glazing (windows in left and right sliding doors) * Navigation system * Navigation pre-installation * Power steering * Partition * Central locking Air conditioning: air conditioner Safety: ABS * ESP Parking assistance: rear * front Lhodsy D Im Tjpfx Ahbog Vehicle has multiple cosmetic signs of use (see pictures), technically very good! Absolutely fixed price

Condition: good (used), Tool holder for SK 40 chucks -made from: Polypropylene copolymer -Impact and scratch resistant, heat resistant -resistant to: mineral oil and various chemicals Lhodpfx Asdm Supshbjg -Price: complete