Used Hydraulic Deep Drawing Press for sale (26,582)

Condition: used, Single-column hydraulic press MAE type S63SZ SO . 551277 Year of manufacture approx. 1977 Nominal pressing force: 63 tons Ncodedzp Trepfx Amnot Pressing force: 50 tons (practically tested) Throat depth: 320 mm Table area: 850 x 630 mm Ram area: 1050 x 500 mm Ram stroke: 500 mm Max. installation height: approx. 730 mm Table height above floor: 970 mm Hydraulic tank capacity: 600 liters Drive power: 15 kW Power supply: 380 Volt, 50 Hz - Hydraulic draw cushion below the table with bores through the tabletop - Two-hand operation - Electrical control cabinet damaged Required space (L x W x H): 2000 x 1200 x 3420 mm Weight approx. 5 tons The machine is operational, the control cabinet is mechanically damaged. During test run, the machine achieves a pressing force of 50 tons, presumably a pressure relief valve is venting.

Condition: used, Hydraulic Synchronizing Press, Spotting Press AGEO Type GHP 200 H6 4-Column Hydraulic Press, Tool Trial Press, Spotting Press Serial No. 21169 Year of manufacture: 1993 Pressing force: 200 tons Clearance between uprights (front): 1200 mm Upright opening (side): 650 mm Table surface: 1560 x 1010 mm Ram surface: 1560 x 1010 mm Ram stroke: 575 mm Draw cushion stroke: 300 mm Draw cushion holding force: 63 tons Draw cushion ejector force: 30 tons Max. installation height: 775 mm Table height above floor: 1000 mm Guide column Ø: 140 mm Clamping pin bore in ram: 64 mm Pressing speed: 0 to 10 mm/s, stepless Return speed: 0 to 20 mm/s, stepless Main motor power: 22 kW Control pump motor power: 5.5 kW Connection: 400 Volts, 50 Hz - Table and ram with 22 mm T-slots - Two pressure cylinders with electronic precision synchronization control - Stepless electronic stroke limitation (top and bottom with digital travel measurement and position display) - Mechanical safety support device (prevents ram from dropping due to dead weight) - Single-hand and two-hand operation - Electrical tool safety via signal contact - Pressure presetting independent of stroke (via keypad, digital pressure display) - Travel measurement system right and left via rotary encoders - Electrical control: MS-DOS PC with Ageo H v2.23 control software - Operator panel with swiveling display - Stroke movement and press force adjustable via joystick - Adjacent hydraulic power unit with electrical cabinet - Hydraulic draw cushion under the press table - Draw cushion with ejector function - Continuous stroke control - Floor-level installation - Electrical oil temperature monitoring - Operating manual with circuit diagrams Space required by press (upright) L x W x H: 1800 x 1010 x 3470 mm Space required for horizontal transport L x W x H: 3500 x 1800 x 1200 mm Ncodswva I Hjpfx Amnjt Net weight press: 13 tons Space for hydraulic power unit L x W x H: 1000 x 800 x 3040 mm Net weight hydraulic power unit: approx. 1 ton The machine was used as a tool trial press in a toolmaking workshop. Very good condition.

Condition: used, High-performance baler MACFAB - BEMA type 650A Hydraulic press for packaging waste, recyclable renewable raw materials, secondary raw materials Manufacturer no. MF J0162 Year of manufacture 2021 Pressing force 50 tons. Press plate stroke approx. 1000 mm Cycle time per stroke approx. 40 sec. Pressing chamber floor area 1500 x 1100 mm Pressing chamber height 1650 mm Filling opening 1500 x 870 mm Filling height approx. 1250 mm Bale format 1500 x 1100 mm Bale height max. 1100 mm Hydraulic operating pressure 200 bar Motor power 5.5 kW Mains connection 400 volts, 50 Hz, 12 amps. - with two hydraulic cylinders - Door locking via threaded spindle with handwheel - Pressing operation only with the pressing chamber door closed - 2-hand operation for hydraulic tipping of the finished pressed bale - Free space for manual strapping - Standard industrial bales of 1500 x 1100 x 1100 mm are produced - the highly compressed bale is automatically tipped onto a pallet - only 62 operating hours Space requirement L x W x H 2120 x 1350 x 3220 mm Height for transport with lowered hydraulic cylinders approx. 260 cm Weight 1.8 ton. The machine is in very good condition, as good as new. Ncsdpsvq Rtkefx Amnet The press has a new price of EUR 22,200 net at BEMA The BEMA company also buys the packaging waste that you press into bales with this press.

Condition: used, Hydraulic notching machine with adjustable angle SIMASV model AV 220-6PA Serial no.: C1524 Year of manufacture: 1996 Blade length: 220 mm Material thickness (steel): 6 mm Material thickness (stainless steel): 4 mm Table dimensions: 950 x 790 mm Table height: 940 mm Motor power: 3 kW Power supply: 400 Volt, 50 Hz - Operation via push-button or foot switch - Adjustable notching angle from 30° to 140° Ncodpfx Ajrzfh Hjmnjt - Angle adjustment via 2 handwheels (right and left) - Hydraulic clamping for the adjustable blades - Electric foot switch - 2 adjustable stop rails with angle scale - Multiple millimeter scales integrated into the table top - HSS blades newly ground, as new Required space (L x W x H): 1000 x 950 x 1470 mm Weight: 750 kg Very good condition

Condition: used, Double column hydraulic press SMG type HBP 200 - 2000 / 2000 make no. 7.4117 year of construction 1986 - rebuild 2000 pressure force 200 ton. Stand passage front 2050 mm column passage sideways 2030 mm table area 2800 x 2000 mm ram area 2000 x 2000 mm ram stroke 700 mm installation height max. 1850 mm Table height above floor 750 mm ram retraction force 33 ton. Rapid feed speed 500 mm/s Pressing speed 72/36 mm/s Return stroke speed 420 mm/s Safety distance 230 mm Motor power main motor 75 kW Motor power control pump 11 kW Mains connection 380 Volt, 50 Hz - 8-fold flat guide for the ram - Clamping plate with 22 mm T-slots at the ram, 2000 x 1900 mm, thickness 60 mm - Hydraulic ram locking at TDC - Measuring system with glass scale - Electrical control renewed in 2000 with SIEMENS SPS S7 - adjacent switch cabinet - 2-hand control panel adjacent - ground level installation - central lubrication - Operating instructions with circuit diagrams Space requirement of the press standing L x W x H 3700 x 2900 x 5900 mm Ncedpfxsdzp Tcs Amnet Machine height complete with motor 5900 mm Space requirement for horizontal transport L x W x H 5900 x 3250 x 2950 mm weight 38 ton. The machine was used as a production press at Volkswagen until 2000. From 2000 the machine was used as a tool testing press in a tool shop. good condition

Condition: used, Year of construction: 2001, Amada HFE 80-25 SL Hydraulic Press Brake. S/No. VO11137 (2001), Remanufactured JTES 2018 Nsdpoy D Rhyofx Amnect Location: These lots are located in Yeovil, UK. Please Note: There are no loading facilities on site, dismantling and loading will be at the cost of the purchaser.

Condition: used, Year of construction: 2022, Bystronic XACT Smart 160/3100 Hydraulic Press Brake. S/No. XACT 22040SE (02/2022), Max Press Force 1600KN, Max Working Length 3100mm, Max Stroke 200mm, Rapid Approach, 140mm/s, Working Speed 1 - 10mm/s, Return Speed 115mm/s, Machine Weight 10,500kg Location: These lots are located in Yeovil, UK. Please Note: There are no loading facilities on site, dismantling and loading will be at the cost of the purchaser. Nodpjy D N R Hefx Amnoct

Condition: used, Year of construction: 2021, Bystronic Xact Smart 225/4100 Hydraulic Press Brake. S/No. XACT21278SE (08/2021), Max Press Force 2250KN, Max Working Length 4100mm, Max Stroke 200mm, Rapid Approach 140mm/s, Working Speed 1 - 10mm/s, Return Speed 115mm/s, Machine Weight 15,000kg Ncjdpfx Aey D N Raomnjt Location: These lots are located in Yeovil, UK. Please Note: There are no loading facilities on site, dismantling and loading will be at the cost of the purchaser.

Condition: like new (used), Year of construction: 2026, pressing force: 20 t, For sale is a C-frame assembly and small-series production press from the manufacturer DURENDUS with a maximum pressing force of 20 tons. The machine has a table size of 700 × 920 mm, a maximum installation height of 550 mm, and a stroke of 400 mm, making it suitable for assembly work, small-series production, pressing operations, and straightening processes in industrial applications. ##### Technical data + information: C-frame assembly and small-series production press – 20 tons – 700 × 920 mm ==== General information - Design: C-frame / single-column press - Manufacturer: DURENDUS - Pressing force: 5–20 tons (adjustable) - Maximum installation height: 550 mm - Table size: 700 × 920 mm - Press head: Ø 100 mm - Table height above the ground: 1,000 mm - Overall dimensions (W x D x H): 900 × 900 × 2,340 mm - Total weight: approx. 1,200 kg - T-slots: DIN 650 – 22 mm or according to customer requirements - Forklift pockets: available - Press area lighting: available ==== Hydraulic cylinder - Stroke: 0–400 mm (adjustable) - Cylinder diameter: Ø 110 mm - Piston rod diameter: Ø 65 mm Ncodpfoy Sx Uwjx Amnot - Maximum working pressure: 280 bar - Return speed: 50 mm/s - Working speed: 10 mm/s - Idle speed: 10 mm/s - Pressure build-up time: max. 2 sec. (steel on steel) ==== Hydraulics & drive - Hydraulic pump: ASC - Delivery rate: 24 l/min - Motor power: 3 kW - Pressure accuracy: ±5 bar - Tank volume: 60 l - Valve technology: DUPLOMATIC - Filter technology: FILTREC - Oil level monitoring: electronic - Cooling: oil-air cooling - Hydraulic unit: mounted at the top rear ==== Control system - Operation: foot pedal or hand lever - Pressure setting: via rotary control - Stroke limitation: via adjustable sensors - Selector switch: foot / hand operation - Switch cabinet components: mostly SIEMENS ==== Safety - Emergency stop switch - Stroke limitation - Stable steel construction - CE-compliant design ==== Electrical connection - Main supply: 400 V AC - Control voltage: 24 V DC - Frequency: 50 Hz - Main motor connection power: 3 kW - Total connection power: max. 5 kW ##### Application areas: Assembly work, small-series production, pressing, straightening, toolmaking, fixture construction, metalworking, maintenance, workshop operations, service applications (Hydraulic press, C-frame press, single-column press, assembly press, small-series production press, workshop press, 20-ton press, pressing press, straightening press, industrial press, C-frame press) Are you looking for a hydraulic press tailored to your specific application? Contact us for an individual offer. Our hydraulic presses are manufactured according to German Machinery Directives and European Machinery Directives (Directive 2006/42/EC), EC standards, and EU safety regulations. Furthermore, our presses exceed Canadian and European safety requirements as they meet all aspects of the national Brazilian safety regulation NR 12, which is based on these. Our strength lies in the design and construction of special machines and press automation. We distribute customized hydraulic presses at surprisingly affordable prices. The hydraulics of the presses predominantly use components from leading European manufacturers.

Condition: used, Year of construction: 2005, Pressure 600 t distance between columns 2600 mm stroke 900 mm Distance table/ram, max. stroke up, adjustment up 1600 mm Table surface area 2500 x 1730 mm pressure of drawing cushion in table 250 t Die cushion stroke in table 400 mm Die cushion area in table 2300 x 1300 mm Die cushion pressure in ram 63 t Die cushion stroke in ram 160 mm Die cushion area in ram 1900 x 1300 mm Ram surface 2500 x 1730 mm Side window 1100 mm Oil volume 3500 l Power capacity 200,0 kW Dimensions (WxDxH) 4,1 x 2,8 x 9,6 m Height above floor 6,4 m year of manufacture 1974 - overhaul 2005: complete new electrical cabinet with control Siemens S7 and safety control Pilz with oil-hydraulic drive, hydraulic controlled drawing cushion in table and ram, hydraulic cutting impact cushioning Ncjdpfevuuh Tox Amnot stored in dismantled condition - Video at seller’s site before dismantling available

Condition: used, Year of construction: 1998, Pressure 800 t distance between columns 3550 mm stroke 1100 mm Distance table/ram, max. stroke up, adjustment up 1900 mm Table surface area 3500 x 1800 mm pressure of drawing cushion in table 350 t Die cushion stroke in table 280 mm Die cushion pressure in ram 80 t Die cushion stroke in ram 160 mm Ram surface 3500 x 1800 mm Side window 1900 mm Weight 100,0 t Ncsdpfevuuhgsx Amnot Floor Space (WxD) 5,3 x 4,3 m Height above floor 7,3 m Height below floor 5,0 - 6,0 m year of manufacture 1970 - overhaul 1998 with oil-hydraulic drive, hydraulic controllable drawing cushion in table and ram, hydraulic cutting impact cushioning, moving table (without rails for the moving table) Height beneath floor approx. 5 - 6 m stored in dismantled condition - Video at seller’s site before dismantling available

Condition: new, Year of construction: 2025, pressure 1000 t distance between columns 4250 mm stroke 400 mm Control SIEMENS S7-1500F table dimension - longitudinal 4000 mm table dimension - cross 1600 mm Ncsdpfx Aoym D E Asmnot total power requirement 200 kW weight of the machine ca. 250 t dimensions of the machine ca. 7,5 x 4,8 x 7,4 m

Condition: excellent (used), functionality: fully functional, Year of construction: 2020, power: 4 kW (5.44 HP), We are offering this very well-maintained Uniflex HM 325.2i_C.2_FD_MVA hose crimping machine with foot pedal, year of manufacture 2020. Model: HM 325.2i_C.2_FD_MVA Serial number: 60046 Voltage: 400 V Ncjdpfx Amoy Apdwenot Current: 15/8.5 A Power: 4.0 kW Frequency: 50/60 Hz Year of manufacture: 02/20 Price ex works. The machine must be collected either personally or via freight forwarding. Payment terms: 50% down payment / 50% upon collection – no cash payments! Payment by bank transfer only. Any warranty and liability are excluded. If you have any questions or require more information, please do not hesitate to send us a message.

Condition: used, Year of construction: 1993, Pressure 1500 t distance between columns 5050 mm stroke 1100 mm Distance table/ram, stroke up 2300 mm Table surface area 5000 x 2700 mm pressure of drawing cushion in table 320 t Die cushion stroke in table 300 mm Die cushion area in table 4300 x 1830 mm Die cushion pressure in ram 120 t Die cushion stroke in ram 200 mm Ncjdovuucqopfx Amnet Die cushion area in ram 3410 x 1650 mm Ram surface 5000 x 2400 mm Speed down 360 mm/s Speed up 168 - 505 mm/s Working speed 19 - 86 mm/s Oil volume 10500 l Power capacity 450,0 kW Weight 400,0 t Dimensions (WxDxH) 3,47 x 6,95 x 12,21 m Height above floor 8,21 m Height below floor 4,0 m year of manufacture 1983 - overhaul 1993 with oilhydraulic drive, drawing cushion in table, drawing cushion in ram (drawing cushion surface) approx. 3410 x 1650 mm), cutting impact cushioning / stroke limitation (adjustment of the spindle approx. 500 mm, max. dampening force approx. 750 t, dampening stroke max. approx. 30 mm), controllabel dependant on pressure/time and way as is where is, WITHOUT dismantling, WITHOUT loading

Condition: good (used), JDS hydraulic press Bed: 505 x 510 mm Dimensions: 140x140x285 cm LxWxH Nsdoiki Ahspfx Amnjct

Condition: used, Year of construction: 2000, total length: 1,000 mm, total width: 1,900 mm, total height: 2,000 mm, Colour: Grey Empty weight: 3.000 kg - Year: 2000 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: 205570 - Drive system: Conventional - Press model: C-Frame press - Press force [ton]: 160 - Max. stroke [mm]: 100 - Table length [mm]: 420 - Table width [mm]: 410 - Table bore diameter [mm]: 60 - Ram length [mm]: 120 - Ram width [mm]: 120 - Transport dimensions: 1000mm x 1900mm x 2000mm (l x w x h) - Transport weight [kg]: 3000kg - Transport packages [pcs.]: 1 Financial information Njdpfsy Ew Euex Amnect VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, Year of construction: 2015, functionality: unexamined, total length: 5,270 mm, total height: 7,290 mm, total width: 5,436 mm, overall weight: 100,000 kg, power: 75 kW (101.97 HP), 1200 T HYDRAULIC PRESS WITH ARCH FRAME – MIB-HYDRO (platform not included) History: Year of manufacture: 2015 Date of acquisition: 03/2015 Mid-2018: Operation ceased Until today: Machine disassembled and stored Specifications: Thrust force = 1200 T Type: ARCH FRAME, Bi-Cylinder Maximum operating pressure = 285 bar Pressure control: Analog sensor Stroke control: Analog linear scale Stroke: V1 = 1000 mm Approach speed = 100 mm/s Return speed = 100 mm/s Dimensions of press platens: 2600 x 1400 mm Maximum clearance between platens (at top dead center): V1 = 2000 mm Slide guide type: (x8) prismatic faces Working height = 1200 mm Mold loading system Control unit: SIEMENS S7-300 Hydraulic power unit power = 75 kW Weight = 100 T Dimensions (H x L x W) = 7300 x 5500 x 5300 mm Contact: Ncodey T N A Iepfx Amnet Christian LEMBLE Price: 72000 (including VAT) MIB Hydro (your model) / Lemacher Hydraulique / Servopresse / Pinette P.E.I. (heavy presses, composites, stamping) / Schaal Technology (special presses) / Schuler (world leader, presses 800–2500 T) / Siempelkamp (heavy presses, forming, composites) / Wepuko PAHNKE (high-capacity hydraulic presses) / Beckwood / Dunkes (special presses, high precision) / Lasco Umformtechnik (heavy forming presses) / Faccin Group / Boldrini / OMCN / Hydrap Presses / Sangiacomo Presses / Beckwood Press Company (USA) — presses 1000–3000 T / Greenerd (USA) — heavy hydraulic presses / Macrodyne (Canada) — presses 1000–5000 T / Phoenix Hydraulic Presses (UK) / Prensa Juaristi (Spain) / Hidrogarne (Spain) / Hydromec (Italy/Spain) / Ermak Press (Turkey) / Yilmaz Machinery (Turkey) / Industrial cutting Cutting of large-sized parts (carpets, technical textiles, polymers) / Cutting of thick sheets or complex metal parts / Cutting of composites or polymer fibers with multi-punch tools. (Arch frame, bi-cylinder presses are designed to ensure parallelism of the slide, which is essential for these operations.) / Stamping / Forming Stamping of metal parts (steel, stainless steel, aluminum) / Cold or hot forming of structural parts / Shaping of automotive or aerospace parts / Compression / molding Compression of composite materials (SMC, BMC, fibers) / Molding of large technical parts / Pressing of polymer or rubber materials / Punching / cambering / straightening Punching of thick sheets / Cambering of profiles / Straightening of deformed parts (sheets, tubes, bars) / Special applications / Compression of technical powders / Pressure bonding / Mechanical tests requiring high thrust (1200 T) / Automotive industry: Cutting of carpets, foams, technical textiles / Stamping of body parts / Forming of structural parts / Aerospace & space: Forming of aluminum or titanium parts / Compression of high-performance composites / Metallurgy & metal processing: Punching, cambering, straightening / Cutting of thick sheets / Chemical industry & materials: Compression of powders / Molding of technical polymers / Technical textile & polymers: Cutting of large textile parts or polymer fibers / Food industry: Pressing of tools or molds for production / Recycling & recovery: Compression of recycled materials / Forming of parts made from recycled materials.

Condition: used, Double column press - Hydraulic Manufacturer REPKON Model 2000/800 kN Condition used description Pressure 200 t Column width 1600 mm ram stroke - max. 600 mm Installation height 900 mm Table width 1600 mm Table depth 1300 mm Table height 1060 mm ram surface 1600 x 1300 mm T-slots Din 650 / 22H12 Rapid traverse 400 mm/s Return speed 325 mm/s Pressing speed 42 mm/s at 40% mm/sec Nedpfxsudb Hce Amnoct Pressing speed 20 mm/s at 100% mm/sec Die cushion pressure 800 kN Die cushion stroke 150 mm Die cushion speed to 68/ from 225 mm/sec Conversion year: 2001

Condition: good (used), For sale is a hydraulic hot plate/molding press manufactured by Italpresse. Technical specifications: Manufacturer: Italpresse Type: GL 14-6/180 Machine designation: PRE46 Nodpfx Amey Ufqqensct Press force: 180 t Max. hydraulic pressure: 600 bar Cylinder stroke: 325 mm Opening: 325 mm CE marking present Control system with operating panel/CNC Condition: used, ready for operation Equipment: Enclosed safety cabin Hydraulic press system Hot plate press / molding press Industrial design Electronic control Condition: The machine comes from ongoing production and is in used, functional condition. Inspection possible by arrangement.

Condition: good (used), Year of construction: 1994, For sale is a hydraulic press from the manufacturer Lauffer Pressen. Technical data: Manufacturer: Lauffer Pressen GmbH & Co. KG Type: VSK 0125 Year of manufacture: 1994 Machine number: 10248/14292 Control system: conventional Condition: used, functional Application area: pressing, forming and shaping operations Equipment: Hydraulic press Control panel with displays and controls Ncjdpfx Amey Ufqkonjt Safety controls Robust steel construction The machine comes from ongoing production and is in used condition with normal signs of wear and tear consistent with its age. Inspection possible by appointment.

Condition: good (used), Year of construction: 1970, pressure 80 t passage width 350 mm stroke 600 mm table dimension - longitudinal 400 mm dimensions of the machine ca. 1400 x 1050 x 2350 m Nedpfxjvwgqro Amnsct

Condition: used, Year of construction: 1985, pressure 40 t stroke 500 mm Ncjdpfoy Rur Nex Amnot throat 360 mm dayligth 1000 mm table surface area 630 x 500 mm table height over floor 1060 / 720 mm ram surface 450 x 360 mm feed down 60 mm/s feed up 300 mm/s power requirement 7,5 kW Weight 2,75 t dimensions of the machine ca. 1,0 x 1,8 x 3,05 mxmxm hole in the table 200 mm with oil-hydraulic drive, intermediate plate (height 340 mm) as is where is, WITHOUT putting into operation

Condition: used, Year of construction: 1989, pressure 100 t stroke 560 mm throat 540 mm dayligth 800 mm table surface area 1000 x 1000 mm die cushion capacity 50 t die cushion stroke 200 mm Nedey Ruq Sopfx Amnsct die cushion area 710 x 650 mm table height over floor 910 mm ram surface 1000 x 1000 mm feed down 400 mm/s feed up 300 mm/s working feed 57,7 mm/s oil volume 650 l power requirement 37,5 kW Weight 15,0 t dimensions of the machine ca. 1,5 x 2,5 x 4,45 mxmxm AS SPARE PARTS DISPENSER

Condition: used, Year of construction: 1980, pressure 250 t distance between columns 1125 mm stroke 250 mm distance table/ram, max. stroke up, adjustment up 800 mm table surface area 1100 x 900 mm pressure of drawing cushion in table 63 t stroke of drawing cushion in table 100 mm die cushion area 700 x 400 mm table height over floor 960 mm side window 700 mm ram surface 1080 x 900 mm oil volume 1000 l power requirement 35,0 kW weight 23,0 t Dimensions (WxDxH) 2,5 x 2,3 x 4,5 m with oil-hydraulic drive, controllable dependent on pressure/time and way, light-guard (Sick), hydraulic drawing cushion in table, cutting impact cushioning Njdpjyx Il Ejfx Amnect No foundation pit necessary

Condition: used, Year of construction: 1984, pressure 200 t distance between columns 1800 mm stroke 710 mm Distance table/ram, max. stroke up, adjustment up 1100 mm table surface area 1600 x 1300 mm pressure of drawing cushion in table 80 t stroke of drawing cushion in table 250 mm die cushion area 1400 x 1080 mm table height over floor 800 mm side window 800 mm ram surface 1660 x 1300 mm speed down 400 mm/s speed up 410 mm/s working speed 14,3 - 49,7 mm/s Nedpjyx Ilrefx Amnjct power requirement 38,0 + 13,0 kW weight 25,0 t Dimensions (WxDxH) 3,65 x 3,3 x 5,4 m height over floor 5,05 m height beneath floor 0,4 m with oil-hydraulic drive, controllable dependent on pressure/time and way, light-guard (Sick) on front and back, hydraulic drawing cushion in table (controllable), hydraulic cutting impact cushioning (in side frame), mechanical depth stop (motoric adjustable), mechanical ram interlocking, two-hand operation