Used Hot Stamping Press for sale (15,852)

Condition: used, Year of construction: 2003, functionality: fully functional, overall weight: 3,500 kg, pressing force: 60 t, input frequency: 50 Hz, operating temperature: 100 °C, input voltage: 380 V, cylinder diameter: 65 mm, SECOND-HAND UNIVERSAL HOT PRESS FOR VENEER AND SOLID WOOD GLUED PANELS WITH SIDE PRESSURE CYLINDERS ORMA MOD. NPC/L Vertical thrust - Total thrust – 60 tons - Specific pressure – 2 kg/cm2 - Plate dimensions – 2500x1300 mm - Cylinders – 4 - Cylinder diameter – 70 mm - Electric boiler thermal power – 18 kW - Voltage – 400/3/50 Hz Horizontal thrust - Total thrust – 25 tons - Cylinders – 5 - Cylinder diameter - ø 65/40 mm - Operating temperature - 100°C - Weight - 3.5 tons - Power - 21 kW 29 A - Voltage - 380/3/50 Hz - Dimensions - 3100 x 1650 x 1800 mm - CE standard Duodpfxjx Rrb Is Afnon - Year 2003

Condition: used, functionality: fully functional, working width: 3,000 mm, HOT PRESS MANNI - Platen dimensions 3000x1300 mm - N. 6 cylinders Dodsx Rqtispfx Afnjun - Boiler with hot water - wooden waste

Condition: good (used), Heidelberg Cylinder KSB 40×57 Hot Stamping Machine A very rare model on the market. The machine is ready for operation and in very good condition. After inspection. Factory-installed new hot stamping unit. Suitable for die-cutting. Central lubrication. Format 40x57cm Dujdpfox Hqmhox Afnen Weight 3500kg 380V power supply Includes additional components, fillers, and letterpress locks.

Condition: new, Die cutting machine TYMC-1200 with hot stamping The latest version, with a „honeycomb” plate with locks. The machine is designed for hot knife die-cutting and standard die-cutting without the need to remove the heating plate. Format: die cutting 1230x850mm Dusdpfx Aowxtb Esfnen hot stamping 1100x780mm Weight 6000 kg Operating speed 23 cycles/min Foil travel 1-820mm Operating temperature 1-150’C Power supply 380V Equipment: – electromagnetic clutch and brake – quick assembly frame – control panel with a touch PLC programmer – three independent foil pulling systems, controlled by stepper motors – 3 operating modes: continuous, time delay, manual – 6 heating plate sections, energy saving – central lubrication – additional safety covers – photocells – operating tools and instructions, CE declaration – sheet for pressure Machine available immediately 12-month warranty.

Condition: used, Year of construction: 1980, functionality: limited functionality, WAGNER MECHANICAL ECCENTRIC PRESS — 500 TON — DOUBLE COLUMN Brand: Wagner Model: 500-ton eccentric press Year: 1980 Mechanical overhaul: 2010 Electrical panel: overhauled 2011 Condition: partially functional Type: double column – eccentric system Strokes/min: 0–30 Ram stroke: 300 mm Ram adjustment: 140 mm Clearance at TDC: 1100 mm Front opening between uprights: 1850 mm Side window: 800 mm Table: 1800 × 1000 mm Ram: 1800 × 1000 mm Number of pressure points: 2 Ram guides: 8 Guards: front and rear Machine dimensions: 3000 × 2000 × 6000 mm Dedpfex A Akzjx Afneun Weight: 55 tons Foundation required: 100 cm Accessories: ELMEA L500 POWER SUPPLY feeder Status: visible in operation

Condition: excellent (used), Year of construction: 2015, operating hours: 5,100 h, Power: 4,000 kN Bolster area: 3,000 x 1,400 mm (W x D) Clamping surface table: 2.950 x 1.500mm Clamping surface ram: 2,950 x 1,240 mm Daylight: 600 mm (stroke down and adjustment on top) Frequency: 5 - 100 rpm, infinitely variable Stroke: 20 - 200 mm, automatically adjustable Ram adjustment: 150 mm (motorized) Design: Dodpfjpvlf Ssx Afnjun - With servo technology, speed of ram adjustable, possible to pendle - Table - clamping plates divided and manually adjustable - 8-fold sliding guide - motorized oil - central lubrication - automatic ram adjustment - pneumatic ram weight compensation - electromotive stroke adjustment - control Siemens + Fanuc - visualization Siemens Panel PC in mobile desk - tool safety device 8-fold - tool data memory - 2-channel press force measurement - Hydraulic overload protection - T-slots in table and ram - Longitudinal groove for tool centering in ram - Anti vibration machine feet - opening in the table Equipped with a complete decoiling line make Lorenz Decoiler Load capacity: 80kN strip width: 20 - 820 mm Inner diameter: 470 - 520 mm Coil - outer diameter 1.800 mm Straightening machine strip width: max. 820 mm Strip thickness: 0,5 - 4,0 mm Straightenable cross section: 1.600mm² Number of rolls: 9 pcs, Ø 65 mm + 2 pcs feeding rolls Speed: 0 - 30 m/min Electronic roll feed Strip width: max. 820 mm Strip thickness: 0.5 - max. 6.0 mm Cross section: max. 2.400 mm² Number of rollers: 2 pcs. Ø 120 mm

Condition: reconditioned (used), Year of construction: 1983, Power: 2.000 kN Frequency: 60 rpm Stroke, adjustable: 20 - 120 mm Daylight: 450mm (max. stroke up) Ram adjustement: 100mm Size of bolster: 850 x 810mm Opening in bolster: 00 x 50mm Ram area: 750 x 810mm Motor power: 22 kW equipped by: - 1pc. con rod - 6pc. guideways - hydraulic overload Djdpsgpxc Ssfx Afneun - motorized oil lubrication - motorized ram adjustment - manuel stroke adjustment - pneumatic ram balancing cylinder - anti vibration machine feet

Condition: good (used), Year of construction: 1976, Pressing force: 20 t Stroke rate: max. 150 rpm, adjustable via PIV gearbox from the control panel Stroke, adjustable: 10 - 50 mm Installation height: 270 mm (maximum stroke at top, without wedge plate) Ram reinforcement: 50 mm Table area: 340 x 320 mm (W x D) Pass-through opening: 70 x 180 mm (W x D) Ram area: 160 x 230 mm (W x D) with wedge plate Drive power: 2 HP Features: - 1 connecting rod - Double V-ram guide - Motorized oil lubrication Duodpfjwufrzex Afnsn - Manual ram adjustment, 50 mm - Mounting bracket for feed unit, tiltable - 3 cams for feed unit etc. - Free-standing control panel - Forward and reverse operation - Manual setup using a rod

Condition: good (used), Year of construction: 1986, operating hours: 10,000 h, power: 30 to (US) , app. 270kN bolster area: 30" x 21" = 762 x 533mm ram-area: 800 x 300mm strokes/min: 100...1400 1/min stroke (fixed): 1" = 25,4mm ram adjustement: 1,75" = 44,5mm Equiped by * Hydraulic clutch * Roll feeder Make: Sankyo Dedpfjnl Snsx Afnsun Type: Variax V70 Width: max. 100mm Only app. 10.000 working hours

Condition: good (used), Year of construction: 1984, Power: 800 kN Frequency: 30 - 200 rpm, adjustable by PIV gearing Stroke, adjustable: 20 - 100 mm Daylight: 500mm (max. stroke up) Ram adjustement: 75mm Size of bolster: 1.010 x 800mm Opening in bolster: 700 x 150mm Ram area: 860 x 700mm Motor power: 22 kW equipped by: - 8pc. guideways - hydraulic overload - motorized oil lubrication - motorized ram adjustment - electro pneumatic stroke adjustment with complete decoiling line make ALBA, consisting of: Decoiler Outer diameter max. 1.400mm equipped by: • Decoiler moveable hydraulic • hydraulic coil loading device • hydraulic drive • hydraulic expansion 480 - 530mm • hydraulic pressure arm, lateral adjustable by handwheel • lateral arms Straightener Type: Ma Ria 9 Width: max. 400mm Thickness: 0,5 - 5,0mm Number of pulling rolls: 2 pc., Ø 120mm, upper can be lifted by hydraulic Number of straightening rolls: 9 pc., Ø 60mm, upper rollls adjustable by hydraulic drive, all rolls supported equipped by: • hydraulic strip insertion device • lateral strip guidings at entrance • lateral strip guidings at exit • basket at exit • loop control by sensor • lateral loop guiding Roll feeder Type: Vhy 400 Width: max. 400mm Thickness: max. 5,0mm Dodpfxodhzf Ie Afneun passline adjustement by hydraulic jack We can offer even only press or decoiling line

Condition: used, Single-column eccentric press WEINGARTEN type ER 63 Machine. No. 52A / 63 Year of construction 1963 Pressure capacity 63 ton. throat 280 mm Table surface 630 x 530 mm ram stroke adjustable 8-100 mm ram adjustment 63 mm Stroke rate 65 strokes / min. Motor power 4 kW Duedpfslb I Dzjx Afnjn Mains connection 380 Volt, 50 Hz - Clutch/brake combination with WEINGARTEN friction threaded clutch - Electric lift release via foot switch - Wheel reduction gear - Overload protection by breaker plate - Front crankshaft support bearing Space requirement L x W x H 1500 x 1100 x 2500 mm Weight 4.5 tons good condition

Condition: used, Single-column eccentric press WEINGARTEN type ARP 100 Machine no. No. 122481 Year of construction 1984 Pressure capacity 100 ton. throat 400 mm Table size 920 x 660 mm ram surface 700 x 450 mm Dusdpfx Afou Rwa Ijnjn Rear upright width 735 mm Stroke adjustment 20 - 160 mm Plunger adjustment 80 mm Installation height with 160 mm stroke max. 355 mm (without intermediate table top) Installation height with 20 mm stroke max. 425 mm (without intermediate table plate) Stroke rate 60 strokes/min. Table surface intermediate table top 920 x 610 mm Thickness of intermediate table top 90 mm Hole in intermediate table top Ø 210 / 180 mm Through-hole in machine table Ø 210 / 180 mm Table height above floor 800 mm (without intermediate table top) T-slot width in table and ram 22 mm Clamping pin bore 50 mm Motor power 11 kW Mains connection 400 Volt, 50 Hz - Hydraulic overload protection in ram - ORTLINGHAUS pneumatic clutch/brake combination - Electromotive ram adjustment with counter - Clamping pin bore with clamping piece - Front crankshaft support bearing - Gear reduction gears in closed oil bath gearbox - Two pneumatic tappet compensation cylinders - WOERNER automatic central grease lubrication - Lift release via electric foot switch or two-hand control panel - Electrical control cabinet permanently attached to the machine - Operating instructions and circuit diagram - UVV for manual insertion work Space requirement L x W x H 2200 x 1600 x 3250 mm Weight 8.3 tons Good condition

Condition: used, Single-column eccentric press WEINGARTEN type E 40 Machine. No. 643/62 Year of construction 1963 Djdpfotx E Rqjx Afnoun Pressure capacity 40 ton. throat depth 250 mm Table opening 150 x 80 and Ø 200 mm Table surface 560 x 460 mm ram surface 250 x 200 mm Plunger stroke adjustable 8-88 mm Plunger adjustment 63 mm Installation height 320 mm Clamping pin bore Ø 40 mm Stroke rate 100/130 strokes / min. Motor power 2.2 / 3 kW Mains connection 400 Volt, 50 Hz Table height above floor 840 mm - Clutch/brake combination with WEINGARTEN friction threaded clutch with TDC run-through protection - Electric lift release via two-hand control - Overload protection by breaker plate - Manual central grease lubrication - Front crankshaft support bearing - Control cabinet adjacent - UVV for manual insertion work Space requirement L x W x H 1800 x 1500 x 2200 mm Weight 3.1 tons

Condition: used, Single-column eccentric press EBU Type 75 SKU Machine no. No. P 4598462 Year of construction 1962 Compressive force 75 ton. throat depth 300 mm Table surface 800 x 620 mm waste hole 325 x 225 mm Plunger surface 470 x 180 mm Clamping pin bore Ø 40 mm Table height above floor 845 mm Stroke adjustment 16 - 140 mm Plunger adjustment 80 mm Installation height max. approx. 420 mm Dsdpfodzqltjx Afnjun Stroke rate 60 + 105 strokes/min. Motor power 4 kW Mains connection 380 Volt, 50 Hz. - Pneumatic clutch/brake combination EBU - Overload protection with breaker plate in ram - UNIDOR tool monitoring system, type APS MINI - mechanically driven gripper feed with belt straightener OSTERKAMP, type ZPN 200/350 - strip width: 200 mm, feed length: max. 350 mm - Strip thickness: max. 3 mm or approx. 200 x 1.5 mm - 2 speeds due to 2 V-belt stages on the wheel transmission - Two-handed operation - Simple work area shielding for swinging open - Table height adjustment in lowest position = threaded spindles for adjustment 50 mm below floor level - Control cabinet and control panel for tool monitoring adjacent - Automatic central lubrication - 4 machine feet Space requirement L x W x H 2600 x 2300 x 2450 mm Weight approx. 5.5 tons good condition

Condition: used, Single-column Eccentric Press MÜLLER GEFREES Type 60 SV DK (Identical to ExP60) Very lightly used eccentric press in original condition Machine No. 5250686 Year of manufacture: 1986 Nearly new condition Press force: 60 tons Throat depth: 280 mm Table surface: 740 x 560 mm Ram surface: 385 x 200 mm Through-hole in table: 300 x 200 mm Table surface (intermediate plate): 740 x 560 mm Through-hole in intermediate plate: Ø 103 mm Intermediate plate thickness: 70 mm Clamping pin bore: 40 mm Table height above floor: 815 mm (with intermediate plate) Installation height, max.: 275 mm (with intermediate plate) Installation height, max.: 345 mm (without intermediate plate) Stroke adjustment: 10–90 mm Ram adjustment: 60 mm Strokes per minute: 100 Motor power: 3 kW Drive: 380 Volt, 50 Hz Dujdpfji A A Tbex Afnon - Mechanical rotary wedge clutch with pneumatic actuation - Spring-loaded single-jaw brake, controlled by cam disc - Stroke release via pneumatic footswitch - Overload protection with breaking plate in the ram - Table height adjustment via 2 threaded spindles - Manual central lubrication system by BEKA Schmiertechnik - Operating manual and pneumatic diagram included Space requirement (L x W x H): 1400 x 1100 x 2200 mm Weight: 3.4 tons In very good, almost new condition

Condition: excellent (used), functionality: fully functional, Segment I – Unwinder with stabilizing table The first segment is responsible for stable guidance of the material web. It is equipped with pins enabling both lamination and delamination of the face with liner or other raw material. It has a laminator with the possibility of precise pressure adjustment. In addition: Dsdpowck U Rjfx Afnjun • The hanging mechanism in each segment allows for continuous operation, eliminating the need to stop the machine while the flat die is working. • Leading (pulling) servomotors ensure precise control of the material, also located in the station. Segment II – Central (Die) The heart of the machine is the flat die, allowing for cutting and embossing. It has been equipped with: • Hot stamping system – thanks to the heated plate with a mounted matrix, it allows for the application of effective decorations. • Upper foil unwinders enabling additional material processing. • Manual pressure adjustment – four independent clocks provide full control over the process, which is particularly important for irregular matrices and unconventional work. • Lower trolley as an alternative to the hanging system – used depending on the specifics of the work. Segment III – Puncher The third segment is responsible for separating cut labels and transporting them to the receiving tray. • Puncher – precise separation of single labels. • Two laminators – one on each side of the puncher, with adjustable pressure. • Unwinders and winders ensuring smooth guidance of additional raw material. Segment IV – Rewinder The last segment is responsible for the final winding of the finished material. Equipped with: • Two mandrels – enabling simultaneous or alternate winding of the finished product. • Web tensioning system (nip holding and web tensioning) – ensuring stable guidance of the material. • Slitting disc knife station. • Whisk (waste) extraction system. • Web sensors placed under each overhang, ensuring optimal process control. Additional functionalities • Remote control – the machine can be operated via the tablet included in the set. • Mark sensor system (register) – precisely matches previously printed raw material, ensuring high accuracy and repeatability of production.

Condition: excellent (used), functionality: fully functional, Brief description Table dimensions: 3000 mm x 1300 mm Number of cylinders: 6 Pressing force: 90 tons Table opening: 400 mm Duodpoxvx Ezsfx Afnon Heating with hot water Boiler: 20,000 kcal/h

Year of construction: 2001, condition: used, machine/vehicle number: 15026, Format: 720 x 1040 mm The machine is a foil hot stamping machine, e.g., for holograms. It consists of a feeder, printing unit, and delivery unit (see photos). A total of 70 machines were built. The machine is currently fully functional with the new control system. Dodpfx Ajwabbvefnjun The estimated cost to bring it into operation is approximately €150,000-200,000 (dismantling, transport, assembly, commissioning, training, documentation for the new control system).

Year of construction: 2004, condition: good (used), coil, coil edge guide Dedpfxjmmc Uie Afnsun brake load cells 12 holographic spool unwinders hot stamping unit cooling suction hood with collection bag boiler refrigerator electrical panel operator panel

Year of construction: 2014, condition: ready for operation (used), functionality: fully functional, machine/vehicle number: JV3D5274-099, For sale is a digital finishing system with hot stamping foil module in very good condition including spare parts dispenser. It has been completely overhauled and is ready for use. Technical data: Make: Mgi Jetvarnish JV3D5274 incl. IFoil module (from Körapackmat) Year of manufacture: iFoil 2014 SN: 3649 / Jetvarnsih 2014 SN: JV3D5274-099 Digital single pass inkjet printing with UV varnish using 8 piezo print heads from Konica Minolta type IHM 1024i (2 x 512 nozzles per head) Mechanical sheet transport with automatic sheet feed on the middle/left or right with ultrasonic double sheet detection. Feeder and stacker with a capacity of 4000 sheets at 135gr/m² (sheet stack up to 60cm high) Pixel-accurate sheet detection with laser keyence sensors for varnish form positioning Dual camera system for print mark detection for print data alignment Flat sheet guide with conveyor belt over a vacuum table that can be adjusted to the sheet width using blinds Air-cooled LED pre-drying directly behind the print head bar Infrared unit for surface varnish application Dodpfxjqfddbj Afneun Air-cooled high power UV drying from market leader IST-Metz Connected foiling unit for hot foil embossing including sleeking option. Heating roller newly installed Dec 2019 (ran approx. 2 km since then) Intuitive production software with an editor for pixel-accurate editing of the varnish layer.

Condition: excellent (used), A3 format Gilding Additional frame Dodpfxoxtwx Ie Afneun Die-cutting material

Condition: used, Year of construction: 1995, Specification: Model: Indumasch Year of manufacture: 1995 For metal up to: 6 mm Djdewql S Hopfx Afnoun Other: foot pedal, interchangeable dies If you have any further questions, we will be happy to answer them.

Condition: used, Year of construction: 2020, functionality: fully functional, For sale: Metal Stamping Press ALP-25C (25T, 2020) Dsdpfxjxmwnie Afneun Condition: Virtually unused, like new. Manufacturer: JINAOLAN Machinery (China) Model: ALP-25C Year of manufacture: 2020-11 A compact and reliable mechanical eccentric stamping press designed for forming, punching, and stamping various metal parts. Technical specifications: Nominal capacity: 25 T Stroke: 45 mm Stroke rate: 145 strokes/min (SPM) Max. die height: 180 mm Height adjustment: 35 mm Ram working area: 170 × 150 mm Bolster area: 370 × 240 mm Country of origin: China Applications: The ALP-25C press is suitable for: stamping, cutting, bending, and forming metal parts; small pressing operations in tool, metal structure, and automotive parts manufacturing; working with thin and medium-gauge sheet metal. If you have any further questions, please feel free to contact us.

Year of construction: 2021, condition: excellent (used), For sale: Metal Stamping Press ALP-25J (25T, 2021) Condition: Virtually unused, like new. Manufacturer: JINAOLAN Machinery (China) Model: ALP-25J Year of manufacture: 2021-04 A compact and reliable mechanical eccentric stamping press designed for forming, punching, and stamping a wide range of metal components. Technical specifications: Nominal capacity: 25 T Stroke: 100 mm Stroke rate: 100 strokes/min (SPM) Max. die height: 260 mm Height adjustment: 55 mm Ram working area: 560 × 370 mm Bolster area: 250 × 220 mm Country of origin: China Applications: The ALP-25J press is suitable for: - Stamping, cutting, bending, and forming metal components - Small press operations in tool, metal structure, and automotive part manufacturing Djdpfxsxm U S So Afneun - Working with thin and medium-thickness sheet metal If you have any further questions, we will be happy to answer them.

Condition: used, Force 1600 tons Slide stroke 300 mm Distance adjustment between table and slider 10 mm Slide strokes per minute 75 spm Length of a rod 920 mm Closed height (min distance table–slide) 660 mm Dujdpox Ek Ntefx Afnen Table dimensions 940 × 1200 mm Table height above floor level 450 mm Slide dimensions 860 × 910 mm Lateral window (h/w) 560x600 mm Main motor 110 kW Dimensions 5060x3940x5125 mm Press weight 120 tons