Used Hollow Plunger Cylinders for sale (8,650)

Condition: used, Hydraulic power chuck cylinder for actuating power chucks Suitable for Gildemeister GDM 42 Through-hole cylinder RÖHM SZS 45/92 559 Ident no.: 414096 Serial no.: 7069 Operating pressure: max. 40 bar Speed: max. 7000 rpm Piston diameter: 125 mm Piston rod diameter: 62/53 mm Piston stroke: 25 mm Ndodpfx Ajy E T A Ajc Asb Inner diameter of cylinder tube: 45 mm Hydraulic power chuck cylinder for opening and closing automatic power chucks. For hydraulic operation of power chucks or collet chucks. Through-hole cylinder for hydraulic actuation of power or collet chucks with a through-bore.

Condition: used, Hydraulic power chuck cylinder for actuating power chucks Hollow clamping cylinder RÖHM SZ-E68/115 459-109 ID No.: 426518 Serial No.: 22950 Operating pressure: max. 50 bar Speed: max. 5,000 rpm Piston diameter: 150 mm Piston rod diameter: 88/100 mm Piston stroke: 10 mm Internal diameter in cylinder tube: 68 mm Threaded connection for draw tube: presumably M79 x 1.5 mm Flange diameter: 185 mm Flange pitch circle: 140 mm (6x M12) Internal centering diameter: 101.7 mm - Flange connection towards spindle side Ndjdpfxjyy Dfko Ac Aob Weight: 25 kg Required space L x W x H: 350 x 250 x 190 mm Hydraulic power chuck cylinder for opening and closing automatic power chucks. For hydraulic actuation of power chucks or collet chucks. Hollow clamping cylinder for hydraulic actuation of through-bore power chucks/collet chucks.

Year of construction: 2005, condition: good (used), Hollow shaft chuck Nedpfx Asgqxg Hec Ajdb Manufacturer: FORKARDT, Type: 3QLC/K250-72-Z8-S12-172005 72mm bore in the chuck with complete clamping cylinder Year of manufacture: 2005, in good condition.

Condition: good (used), Lifting capacity 24t Ø98 x 315mm Stroke 150mm Cylinder Ø 56mm Bore Ø 27mm Ndjdpfx Asvwb Sdjc Aeb 238kN Around 130x available Shipping from 10 pieces

Condition: used, Little used European Spraydry Technologies model 8 - 19 Tall Form Spray 304 stainless steel ATEX rated spray dryer system. Mass balance design capabilities approximately 246kgs feed @ 10% solids with 26kgs Powder @ 5% residual moisture + 220kg/h water evaporated based on Potato Proteins. Inlet temperature 190 deg.c. with exhaust temperature 90 deg.c. Mass flowrate of drying air rated 6,895kg/hr. System includes the following parts: (1) Airco model CHP inlet fan driven by 11kw motor. (1) Lanemark model DB07 propane burner with control panel. (1) Tall form spray dryer chamber with conical base fitted with dislodging hammers fitted to cylinder and cone. Access/inspection doors. Explosion suppression bottles. (1) Stainless steel feed lance with pressure nozzle. (1) 304 Stainless steel product cyclone with explosion suppression bottles. Includes DMN Westinghouse type AL250DairyMZC-11 APS rotary lock value with motor. (1) Exhaust air chamber with explosion suppression bottle. (1) Gough type GBS550 stainless steel vibratory sifter/screen, mounted on stainless steel mobile frame. (1) Feed balance stainless steel vertical vessel. (1) FBF Italia model FBF2004/P High pressure plunger pump. (1) Mettler Toledo type V4-REM industrial flow-though metal detector with Piab conveying system. (1) Airco type CHP825 exhaust fan driven by 30kw motor. (1) Robbe model Atlas filling machine for bags with controls. Various small scale circulation pumps, pipework, instrumentation and ducting available. Ndsdjz D Efnspfx Ac Aeb Specifications: Material Of Construction: 304 Stainless Steel Type Of Spray: Nozzle

Condition: excellent (used), Year of construction: 1990, functionality: fully functional, Traub CNC turning machine TNA480, TX8D, year of manufacture 1990, serial number 607. Servo C-axis, reinforced rotary tool drive, 1 turret VDI40, tailstock, chip conveyor, 3-jaw chuck KNCS315, ID090090. Main drive with 2 gear stages. A8 spindle with hollow clamping cylinder Röhm SZS 86/169, ID 416530. Additional accessories, tool holders, chucks available upon request. Includes ATC optics, spare parts catalog, wiring diagram, tool holder catalog. Very good condition, operational, can be inspected while running. Machine geometry has been checked and corrected/adjusted, and a test run has been performed. Scraper + belt + drive sprocket, belt checked and replaced, maintenance performed at 4000 hours. Technically very good condition, guideways, spindle bearings in very good condition. Ndsdpfxsz Eqh De Ac Aob Videos available upon request.

Condition: good (used), functionality: fully functional, Year of construction: 1991, operating hours: 10,000 h, load capacity: 3,000 kg, fuel type: gas, motor manufacturer: Fendt, DGUV certified until: 07/2027, overall weight: 3,000 kg, empty load weight: 4,810 kg, color: red, Equipment: CE marking, pallet forks, sideshift, Good day, We are selling our 3-ton forklift because it is no longer needed. The forklift has undergone extensive technical refurbishment. Approximately €4,500 has been invested in the latest work. All work is documented with invoices. The following work has been carried out or components replaced, among other things: Both lifting cylinders replaced Complete mast lines replaced Complete rear axle steering replaced Diaphragm replaced Plunger replaced Complete service performed All work is documented with invoices New TÜV/UVV inspection For its age, the forklift is in very good condition and has been well maintained technically (see photos). The engine runs very well. The machine has not only been cosmetically refurbished, but significant investments have been made in important technical components. If you are looking for a robust, durable 3-ton Linde forklift for use in a business, workshop, mechanical engineering company, or industrial setting, and you don’t want a modern plastic forklift, you will find a solid machine here. Test drive and inspection are welcome. Ndedpfezy Hxwjx Ac Aob Please feel free to contact us if you are interested. Best regards

Condition: ready for operation (used), Year of construction: 2023, operating hours: 1,904 h, spindle speed (max.): 4,000 rpm, travel distance X-axis: 260 mm, travel distance Z-axis: 795 mm, spindle motor power: 18,500 W, controller manufacturer: MITSUBISHI, controller model: M730UM, number of slots in tool magazine: 12, number of axes: 5, This 5-axis DMG MORI MORI NLX 2500/700 SY was manufactured in 2023. It features a turning length of 700 mm and a powerful main spindle with a maximum speed of 4,000 rpm. The machine is equipped with a 12-station turret and integrated automation for efficient parts handling. If you are looking to get high-quality turning capabilities, consider the DMG MORI MORI NLX 2500/700 SY horizontal turning machine we have for sale. Contact us for further details. - Control Unit: MITSUBISHI M730UM with CELOS (MAPPS V) on 21.5-inch Multi-Touchscreen ERGOline Touch- Turning Length: 700 mm- Main Spindle (Spindle 1): 18.5/18.5/15 kW (25% ED/50% ED/cont.), 4,000 rpm, JIS A2-8 spindle nose, Ø91 mm spindle bore- Main Spindle Chuck: 10" Hydraulic 3-jaw chuck (Kitagawa BR10A821, Ø254 mm) with hollow clamping cylinder (Ø80 mm bar passage)- Counter Spindle (Spindle 2): 11/7.5 kW (25% ED/cont.), 6,000 rpm, JIS A2-5 spindle nose, Ø43 mm spindle bore- Counter Spindle Chuck: 6" Hydraulic 3-jaw chuck (Kitagawa BR06A521E, Ø170 mm) with full clamping cylinder- Turret: 12-station BMT60 turret with 10,000 rpm driven tools (5.5/5.5/3.7 kW power, 40/30/14 Nm torque)- Y-Axis Travel: ±50 mm (Rapid traverse 10 m/min)- X-Axis Direct Measuring System: Magnetic linear scale system (0.01 µm resolution)- Tool Setter: Manual swing-type tool presetter for Spindle 1 and removable tool presetter for Spindle 2- Automation & Parts Handling: Integrated parts catcher for main/counter spindle (up to Ø80 mm x 200 mm, 3 kg max), workpiece discharge conveyor belt, pneumatic workpiece ejector (Spindle 2)- Bar Feeder & Interface: Bar feeder interface (multi-brand) with Top Automazioni X-Files 380M 3m bar feeder (80 mm max bar diameter)- Coolant & Filtration System: Hinge-belt chip conveyor (right side discharge), 0.8 MPa high-pressure coolant pump, INTERLIT pump unit with 15 bar high-pressure pump & double cartridge filter, coolant gun- Auxiliary Equipment & Interfaces: Oil mist collector interface (Ø150 mm port), 3-phase autotransformer (45 kVA, 400V/200V, 50 Hz), double foot switch for chuck operation- Machine Operating Hours (from HMI readout):- Machine Power-On Time: 8,120 hours- Program Run Time Head 1: 3,751 hours- Cumulative Cutting Time Head 1: 1,904 hours Technical Specification Nodpjzy N Nljfx Ac Aodb Counter Spindle Yes Driven Tools Yes

Condition: ready for operation (used), functionality: fully functional, Year of construction: 1985, machine/vehicle number: 8444-08, workpiece length (max.): 6,000 mm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Maximum edge length: 6,000 mm Maximum material thickness: 1.25 mm Mechanical cutting device Hydraulic unit Flow rate of gear pump: 14.5 l/min Operating pressure: 140 bar Maximum pressure: 210 bar Electric motor power: 3 kW Motor speed: 1,450 rpm Voltage: 380 V Frequency: 50 Hz Oil tank capacity: 30 l Ndodpfxozy Ndce Ac Aeb Pressure gauge diameter: 63 mm Pressure gauge display range: 0–250 bar Pressure switch: 90 bar Hydraulic components Gear pump CPL 9 DQ Intermediate flange L25-2/004 Elastic coupling G 228/2P Return filter Fill and vent filter Oil level indicator Drain plug Glycerine pressure gauge Valve block with pressure, flow control, braking, and solenoid valves Hydraulic cylinders Number of hydraulic cylinders: 8 Type: GHZ-50 × 225-S spec. Piston rod with external thread M20 Length: 20 mm Swivel bearing at the rear Hydraulic motors Number of hydraulic motors: 4 Type: OMP 50 MACHINE DETAILS Control system Electrical machine control with operator panel (OP) Adjustable dwell times, angle ranges, and shutdown delays Variant control for different machine functions EPROM-based control Electrical supply Mains voltage: 380 V Frequency: 50 Hz EQUIPMENT Hydraulic unit OP-14 SM 8 hydraulic cylinders GHZ-50 × 225-S spec. 4 hydraulic motors OMP 50 Gear pump CPL 9 DQ Valve block with hydraulic valves Return filter Fill and vent filter Oil level indicator Glycerine pressure gauge Pressure switch Electrical OP control Hydraulic and electrical circuit diagrams

Condition: good (used), Year of construction: 2017, functionality: fully functional, machine/vehicle number: 4480, total length: 14,500 mm, total width: 7,800 mm, total height: 3,500 mm, overall weight: 20,000 kg, Reichenbacher Machining Center VISION III-TT-L – 5-Axis, 3-Axis, MBG8, 5x SNA Equipment: 5-Axis Unit with Cardanically Mounted Spindle: Max. speed: 24,000 rpm Nominal speed: 10,000 rpm Nedpsywzq Ssfx Ac Ajdb Power in S1*: 15 kW Max. power in S6: 20 kW Torque in S1*: 14.5 Nm Torque in S6: 19 Nm Nominal voltage: 380 V Nominal current: 37 A Nominal frequency: 380 Hz Speed freely programmable from 0 – 24,000 rpm, in 1 rpm increments Clockwise/counterclockwise rotation selectable via program Driven by frequency inverter Maintenance-free Water-cooled Hybrid bearings Automatic spindle stop in case of emergency stop Orientated stop for thread cutting Tool holder: HSK-F63 hollow shaft taper according to DIN 69893-6 Max. tool length usable from spindle nose: 240 mm Max. tool weight: 6 kg 3-Axis Unit with Vertically Mounted Spindle: Max. speed: 24,000 rpm Nominal speed: 10,000 rpm Power in S1*: 15 kW Max. power in S6: 20 kW Torque in S1*: 14.5 Nm Torque in S6: 19 Nm Nominal voltage: 380 V Nominal current: 37 A Nominal frequency: 380 Hz Speed freely programmable from 0 – 24,000 rpm, in 1 rpm increments Clockwise/counterclockwise rotation selectable via program Driven by frequency inverter Maintenance-free Water-cooled Hybrid bearings Automatic spindle stop in case of emergency stop Orientated stop for thread cutting Tool holder: HSK-F63 hollow shaft taper according to DIN 69893-6 Max. tool length usable from spindle nose: 240 mm Max. tool weight: 6 kg 8-Spindle Drilling Unit (1 unit): L-Shape, Grotefeld Drill spindles: individually selectable Rotation direction: clockwise/counterclockwise Pitch: 32 mm Power: 2.5 kW Speed: 5,000 rpm fixed Z-axis stroke: +75 mm Holder: D = 10 mm H7 Plunge stroke: 80 mm Grooving Unit (5 units): GROTEFELD Angle Saw Unit F100-S The working/milling stroke is pneumatic. Drive: three-phase motor with multi-ribbed belt LEFT version Drive rotation direction: clockwise/counterclockwise Speed reduction: 1:2.86 – belt drive Power: 2.20 kW – 220-240/380-415 V – 50 Hz Speed: n1 = 2,800 rpm, n2 = 8,011 rpm at 50 Hz Spindle power: 2.2 kW Feed: 150 mm Tool holder: Ø30 x 1.5 mm – 5.0 mm Tool holder rotation: opposite to drive rotation direction Feed force: 2565 N Underfloor Drilling Unit in Machine Bed (1 unit): GROTEFELD Angle Milling Head G06-1.1-P The working/drilling stroke is pneumatic. Drive motor: 1.1 kW 220-240/380-415 V 50-100 Hz Drive rotation direction: clockwise Speed reduction: 1:1.55 gear drive Drive speed: 2,800 – 5,600 rpm Tool spindle speed: 4,340 – 8,680 rpm Tool holder: 1x HI-Q/ERM25 DIN6499-C (8°) For ER25 collet DIN 6499-B Ø0.5–16 mm max. Tool holder rotation direction: clockwise Flange clamping piece: FK45 Feed slide: with pneumatic cylinder and double steel guideways Feed: 80 mm

Condition: like new (used), Year of construction: 2024, For sale: 8-colour offset printing press RMGT 970PF-8, configuration 8/0 or 4/4, with convertible perfecting unit. The machine is designed for high-quality industrial printing and is equipped with an extensive range of automation systems, including presetting, register control, cleaning systems, and colour measurement. Main technical specifications: Maximum paper size: 650 × 965 mm Minimum sheet size: 290 × 410 mm Minimum sheet size in perfecting mode: 370 × 410 mm Maximum printing area: 640 × 930 mm Maximum printing area in perfecting mode: 630 × 930 mm Maximum printing speed: 15,000 sheets/hour Nodpfx Aey S S Azjc Ajdb Stock thickness: 0.04–0.5 mm Plate size: 700 × 945 × 0.30 mm Feeder pile capacity: 1,100 mm Delivery pile capacity: 1,100 mm Machine dimensions L × W × H: 12,960 × 3,453 × 2,011 mm Equipment and features: PCS-G Printing Control System Rotary stream feeder Static eliminator on delivery Mechanical double-sheet detector Vacuum suction-type feeder board Paper size preset system Registration device Vertical and lateral image micro-adjustment Ultrasonic double-sheet detector Slewed sheet detector Side lay detector Front-lay Bernoulli device Side lay preset Printing, inking and dampening units: Straight edge plate clamp with positioning pins Infed lower swing gripper feed drum Gripper margin: 10 mm Remote control for vertical, lateral and diagonal register 19 inking rollers, including form rollers 4 dampening rollers R-matic dampening system Oscillating bridge roller Double-double-single perfecting cylinder configuration Delivery section: Static eliminator Chain gripper delivery Delivery jam detector De-curler device Board insertion device Powder sprayer High pile delivery Delivery area sensor Paper size preset system Paper guide under the first delivery drum Delivery belt guide Belt-type vacuum slow-down wheels Additional options: Automatic feeder pile lateral alignment function Blower guide under the swing Pneumatic pull side guide Feeder air preset Impression pressure preset Impression cylinder cleaning function Feed drum fan-out adjustment mechanism Automatic blanket cleaning device Automatic ink roller cleaning device Smart-FPC plate changing device Ink form rollers 1st–3rd oscillating Hollow rollers for ink roller temperature control system R-matic_D remote ON/OFF Technotrans alpha.c chiller with alcohol density control Photo-type delivery pile lowering sensor Delivery fan antistatic eliminator PPC Server III for CIP-4 file transfer Press information display LithoFlash® Inline RMGT 970 Recto Verso automatic inline measurement system LithoFlash software package: LithoDyn ADR, LithoDyn JobChange, LithoFlash OneShot Machine raised by 200 mm The machine has CE marking, safety covers, tools, and documentation in English. The machine is sold in its current condition and at its current location — “as is, where is”. Inspection is possible by prior arrangement. An excellent solution for printing companies requiring a modern, high-performance 8-colour offset press with 8/0 and 4/4 printing capability and advanced process automation.

Condition: excellent (used), Tucker Nimak MF180: Robotic welding tongs for single-sided resistance spot welding The robotic welding tongs for single-sided resistance spot welding from NIMAK utilize state-of-the-art medium-frequency transformers, a control system with adaptive welding current regulation, and finely adjustable welding cylinders for gentle power. Here, the right amount of force is crucial to reliably join materials without deforming them Ndsdpfxozgcm Rj Ac Ajb or leaving marks on the visible side. Our systems master this task perfectly. Tucker Stanley Punch Riveting Tool, C-Frame With the Tucker® SPR equipment, you can join materials that cannot be easily welded, including aluminum-aluminum, aluminum-steel, and high-strength steel, by combining two technologies in a modular system: punch riveting with semi-hollow rivets and solid punch rivets. AEG SVS Welding Technology Electrode Grinding Device EF310-01E-S-D-Fix Grinding of spot welding electrodes Automatic rivet feed With controller: The brain of every SPR system. It manages, thinks, remembers, and communicates in an Industry 4.0 environment. The lung – small, quiet, and fast rivet feed for your SPR tool. Condition: used Scope of delivery: (See image) (Changes and errors in the technical data are subject to change!) We will gladly answer any further questions you may have over the phone.

Condition: good (used), Year of construction: 1997, operating hours: 13,886 h, lifting height: 4,300 mm, fuel type: diesel, mast type: triplex, construction height: 2,300 mm, Toyota 02-6FD35 Triplo 430 Freelift / Sideshift / Fork Adjuster, 6-cylinder Diesel. A video can be sent via WhatsApp. We have a continuous stock; see our website. Prices are quoted ex works Nuland. Njdpfxoz Eiu Ne Ac Ajdb Van de Wert Trading B.V. has a varying stock of machines, trucks, trailers, and attachments. All our deliveries are offered at trade prices in AS-IS condition, without warranties (see our general terms and conditions). You can make a non-binding appointment for a viewing and/or test drive. Please call beforehand, as we are not always on site. Van de Wert Trading B.V. Bedrijfsstraat 3 5391 LR Nuland

Condition: ready for operation (used), Year of construction: 2020, operating hours: 7,597 h, functionality: fully functional, machine/vehicle number: NL257200651, turning diameter: 366 mm, spindle speed (max.): 4,000 rpm, controller model: Mitsubishi 730UM CELOS, working length: 700 mm, number of slots in tool magazine: 12, TECHNICAL DETAILS Maximum machining length: approx. 700 mm Maximum turning diameter: 366 mm Workpiece length with tailstock: max. 728 mm Spindle speed: max. 4,000 rpm Tool turret: 12-position BMT60 star turret Tool drive: 40 / 14 Nm Speed of driven tools: max. 10,000 rpm Overhang length of driven tools: 100 mm Chuck: 10" hollow chuck, Ø 254 mm Chuck cylinder: hollow chuck cylinder BB210A821 Tailstock: NC tailstock Tailstock taper: MK 5 MACHINE DETAILS Coolant type: water-miscible coolant / emulsion Coolant pressure: 5 bar Extraction connection: Ø 150 mm Mains voltage: 380 V Frequency: 50 Hz Transformer power: 45 kVA Phases: 3 phases Isolation transformer: 400 V ± 5 % Current: 65 A Control system: Mitsubishi 730UM CELOS User interface: CELOS with ERGOline touch panel Machine operating time: 7,597 h Program runtime: 2,138 h Last maintenance: April 2024 Weight: 5,800 kg EQUIPMENT DMG MORI M730UM control system with CELOS ERGOline touch panel 12-position BMT60 star turret with driven tools 10" hollow chuck, Ø 254 mm Hollow chuck cylinder BB210A821 Double foot switch with protective cover NC tailstock with MK-5 mount Oil-air cooler for circulating spindle coolant Hinged belt chip conveyor High-pressure coolant system, 5 bar Oil mist separator AFS 1100 including interface Manual, swiveling tool pre-setter SCHNEIDER transformer 45 kVA Technology cycle "Alternating Speed" Ndedpjzy Hx Defx Ac Asb Further technical data can be found in the document attached!

Condition: ready for operation (used), Year of construction: 2022, spindle speed (max.): 2,800 rpm, travel distance X-axis: 280 mm, travel distance Z-axis: 830 mm, spindle motor power: 30,000 W, total height: 1,915 mm, total width: 2,035 mm, overall weight: 5,650 kg, product length (max.): 3,821 mm, number of axes: 3, This 3-axis DOOSAN Puma GT 3100 M was manufactured in 2022. It features a maximum turning diameter of 376 mm and a turning length of 725 mm. The machine is equipped with a 12-station tool turret and a three-jaw power chuck diameter of 305 mm. If you are looking to get high-quality turning capabilities, consider the DOOSAN Puma GT 3100 M horizontal turning machine we have for sale. Contact us for further details. • Siemens S828D control touchscreen with ShopTurn 15-inch display • 3-axis CNC horizontal turning machine with driven tools and tailstock • C-axis main spindle: 360° resolution 0.001° • C-axis speed: 200 rpm • C-axis torque: approx. 1162 Nm • Swing diameter over bed: 720 mm • Swing diameter over cross slide: 590 mm • Max turning diameter: 376 mm • Max turning length: 725 mm • Main spindle bore: 115 mm • Bar capacity: 103 mm • Spindle nose: ASA A2-11 • Max torque: approx. 1112 Nm • Rapid traverse X-axis: 24 m/min • Rapid traverse Z-axis: 30 m/min • Feed force X-axis: 9465 N Ndjdpjy E I Hisfx Ac Aeb • Feed force Z-axis: 17379 N • Three-jaw power chuck diameter: 305 mm with soft jaws • 12-station tool turret with BMT65P tool holders • Max driven tool speed: 5000 rpm • Driven tool power: approx. 7.7 kW • Driven tool torque: approx. 75 Nm • Tailstock with quill diameter: 100 mm • Quill stroke: 100 mm • Hydraulic clamping system with hollow cylinder • Monoblock cast iron machine bed, Meehanite construction • 30° slant bed design • Hardened and ground guideways with low-friction coating • Automatic central lubrication • Coolant system: 7 bar pressure • Coolant tank capacity: approx. 235 liters • Hydraulic tank: approx. 20 liters • Full enclosure with working area lighting • Bar feeder interface • Oil skimmer • Electronic safety clutch for X and Z axes • Electrical connection: 400 V, 3-phase, 50 Hz • Total power: approx. 47 kVA • Unused (like new) • OPTIONAL: HALTER LoadAssistant Universal Big 70 (Robot) • Gripper for Doosan Universal Big 70 • Rotation Station • Workpiece Support • Base Plate 23 mm / 175 mm Big 70 • Machine Interface Box • () Technical Specification Counter Spindle No Driven Tools Yes

Condition: new, *IMMEDIATELY AVAILABLE* Includes: E & Emergency hand pump, Full steel floor Equipment: - Charger - 6x Lashing points - Electric pump Net: €6,008.40 / Gross: €7,150.00 Article number: UDK230301811.01 Technical data: • Brand: Unsinn Ndjdpfszy A E Hox Ac Aeb • Model: UDK 3017-30-14 • Vehicle type: Three-way tipper • Vehicle condition: New vehicle • First registration: without first registration • TÜV/HU: 2 years from first registration • Internal dimensions (L x W x H): 306 x 175 x 35 cm • External dimensions (L x W x H): 450 x 191 x 113 cm • Loading height of the floor: 78 cm • Permissible total weight: 3,000 kg • Unladen weight: 790 kg • Payload: 2,210 kg • Chassis: High loader (wheels under the body) • Tires: 185R14C • Suspension: ALKO rubber spring axle • Support wheel: Yes, automatic, 500 kg • 100km/h approval: Optional, can be retrofitted DESCRIPTION • Unique, torsion-resistant longitudinal frame chassis for safe driving characteristics • Aluminum side panels anodized, double-walled • All side panels can be folded down and removed • Steel corner posts removable • Rear flap can also be pivoted • Option to attach at all 4 corners for tarpaulin frames, grid extensions, side panel extensions or front wall extensions • Stable toggle lever locks • Full steel floor, 3mm hot-dip galvanized – extremely robust • Drawbar and frame hollow profile construction welded and completely hot-dip galvanized • Many cross members, resulting in high point load capacity • All transverse and longitudinal members rest on the ground • 6 folding lashing points, mounted recessed in the floor frame profile (600DaN/kg) • 6 lashing points under the loading area • U-profile on the rear, for easier attachment of the ramps • Ramp compartment prepared • Solid 4-stage hydraulic cylinder • Electric hydraulic pump with battery (12V/75AH) in the box incl. cover • Emergency hand pump, for manual tilting in case of empty battery • Detachable remote control for E-hydraulics • Integrated battery charger with Schuko plug • Maintenance-free rubber spring axles from ALKO • Reverse drive automatic • ALKO overrun device and parking brake • 13-pole plug • Reversing light • Large-sized safety lighting • Integrated rear fog light • Lighting recessed in the rear frame • Reinforced, automatic support wheel, for safely parking the loaded trailer, load capacity 500kg • Premium maneuvering handle with ratchet strap reel _____ Accessories can be retrofitted by our specialist workshop!! - Feel free to request any specific requirements! _____ - Financing or leasing possible - Delivery nationwide possible - All prices include VAT. - Vehicle registration certificate can be sent in advance or transfer plates (Germany) can be provided. - Export registration plates including customs registration possible Descriptions and images are subject to copyright!! Anhänger Zentrum BAUMANN GmbH Dekkers Waide 17 46419 Isselburg Over 1,200 trailers immediately available for you! We have been Brian James / Blyss / Debon / Humbaur / Hapert / Unsinn / Cheval Liberte / Koch / Lorries / Martz / Stedele / TPV / Tohaco / Vezeko / Variant / Vlemmix - specialist dealer & repair - workshop for over 30 years - Subject to errors, omissions and prior sale -

Condition: used, Year of construction: 2016, operating hours: 18,071 h, functionality: fully functional, machine/vehicle number: 06960000941, spindle motor power: 25,000 W, spindle speed (max.): 5,000 rpm, rapid traverse Y-axis: 30 m/min, torque: 280 Nm, input voltage: 400 V, overall weight: 6,000 kg, power: 25 kW (33.99 HP), input frequency: 50 Hz, controller manufacturer: Siemens, controller model: Sinumerik 849D sl, input current: 63 A, tool type: VDI 40, number of axes: 3, DMG MORI CTV 250, 2nd Generation – Vertical Turning Center (Pick-up), Year of Manufacture 2016 For sale is a well-maintained DMG MORI (Gildemeister) CTV 250, 2nd Generation, manufactured in 2016, with only 18,071 spindle hours. The machine is fully equipped for automated series production of chucked parts and is currently still powered on – inspection and demonstration possible by arrangement. Nodpfxjzi R R No Ac Asdb Control System & Drive Siemens Sinumerik 840D sl (Slimline) including ShopTurn option AC main drive 25 / 32 kW, torque 280 / 360 Nm Spindle speed up to 5,000 rpm, duty cycle 100 % / 40 % Hollow cylinder, programmable clamping pressure via NC program Axes & Tools 12-station turret (disc diameter 340 mm), all stations powered (UDI 40) C-axis with powered tool system Y-axis +90 / -65 mm Linear guides, ball screws, glass scales, AC servomotors with absolute encoder Rapid traverse 30 m/min Automation & Metrology Workpiece transport system SRA 160 (drag chain, NC-controlled) including drag chain set Storage capacity: 30 parts (Ø 30–70 mm, max. 7 kg) or 18 parts (Ø 30–100 mm, max. 15 kg), max. total weight 320 kg including pallets Workpiece diameter 30–160 mm, workpiece height max. 160 mm Robot interface Profinet (electrical interface for 6-axis robot) Workpiece probe Renishaw LP2DD at the loading/unloading station, measuring accuracy 10 µm, with air blow cleaning Coolant & Peripherals Coolant system 8 / 20 bar, tank 600 l, high-pressure pump 20 bar / 40 l/min Coolant supply via turret disc to all stations Band filter system 40 µm with forced indexing, coolant level monitoring Hinged belt chip conveyor with extended discharge chute (+300 mm), enlarged chip container, modified sludge pump Aluminum machining package Integrated work area extraction max. 400 m³/h, work area flushing with 3 flushing nozzles Cabinet cooling up to 40 °C, hydraulic oil cooler Air blower via main spindle, 4-color signal light Remote diagnostics via the internet Connection values: 400 V / 50 Hz, 40 kVA, 63 A · Weight: approx. 6,000 kg Sale from current location, dismantling/loading/transport by arrangement or by the buyer. Sale is subject to the exclusion of all warranties (commercial sale of used machines, sold as seen). Please contact us if you have any questions or would like to arrange a viewing.

Condition: excellent (used), Year of construction: 2023, functionality: fully functional, turning length: 111,111 mm, We offer you the following: Manufacturer: DMG MORI Model: NTX 3000/1500 Year of manufacture: 2023 Control: DMG Mori Celos with Fanuc F31iB5 Technical specifications: Max. turning diameter: 670 mm Turning length: 1,519 mm Bar capacity: max. 102 mm Travels: x1-axis: 675 mm y-axis: +/- 150 mm z1-axis: 1,562 + 164 mm b-axis: +/- 120° a-axis: 1,542 mm x2-axis: 200 mm y2-axis: +/- 40 mm z2-axis: 1,542 mm Main spindle: Max. speed: 3,000 rpm Drive power: 30/25 kW Torque: 1,194/995 Nm Spindle nose: JIS A2-8 Spindle bore: Ø 111 mm Counter spindle: Max. speed: 4,000 rpm Drive power: 18.5/18.5/15 kW Torque: 599/505/409 Nm Spindle nose: JIS A2-8 Spindle bore: Ø 91 mm Milling spindle: Speed range: 0 – 12,000 rpm Drive power: 28/23 kW Torque: 132/95.3 Nm Tool holder: Capto C6 Number of tool stations: 76 positions Max. tool diameter: Ø 70/Ø 130 mm Max. tool length: 400 mm Max. tool weight: 8 kg Turret: Number of tool holders: 12 positions Speed of driven tools: 12,000 rpm Tool holder: BMT40 Torque: 16.9 Nm Rapid traverse speeds: x-axis: 50 m/min y-axis: 40 m/min z-axis: 50 m/min a-axis: 36 m/min x2-axis: 25 m/min y2-axis: 18 m/min z2-axis: 40 m/min b-axis: 100 rpm Operating hours: approx. 4,500 h Spindle hours: approx. 2,200 h Technical features & accessories: − Hydraulic 3-jaw chuck, manuf. SMW KNCS-N-400-128 incl. hollow clamping cylinder for main spindle − Hydraulic 3-jaw chuck, manuf. SMW KNCS-N-260-78-3Z incl. hollow clamping cylinder for counter spindle − Foot switch for chuck operation − Automatic clamping stroke monitoring of the clamping cylinder for main and counter spindle − Tailstock function for counter spindle − Magazine-side control panel for the tool magazine − Coolant: water-soluble coolant − Chip conveyor (right discharge) − Coolant temperature control/coolant chiller − Coolant spray gun − Float switch for coolant − Coolant shower at main and counter spindle chucks − Compressed air blow-off system for chuck (counter spindle) − Oil mist separator zeroGOF #2 − Oil separator − ICS 70 bar, TMF300 band filter system, 980 l tank − Manual tool presetting device for main and counter spindle − Direct measuring system in x1, x2, y, z1, z2 axes − Spindle sensor measuring system with wireless signal transmission, manuf. Renishaw RMP600 Ndodpey Sfx Nofx Ac Ajb − Universal filter − 3D quickSET − Cycle Alternating Spindle Speed − Cycle "Tailstock Tip at Turret" − Cycle MPC – Machine Protection Control − Cycle MVC – Machine Vibration Control − Synchronous thread cutting without compensating chuck − Increased input resolution to 0.0001 mm − Cs control for tool spindle − Program restart Accessories, illustrated tools, and clamping devices are only included if specified in the additional information. Technical data and details subject to change, errors and prior sale excepted!

Condition: new, *AVAILABLE IMMEDIATELY* Includes: E & emergency hand pump, all-steel floor Features: - 8 lashing eyes - Electric pump - Battery charger Net: €7,134.45 / Gross: €8,490.00 Article number: UDK235361811.01 Technical data: • Brand: Unsinn • Model: UDK 3617-35-14 • Vehicle type: Three-way tipper • Vehicle condition: New • First registration: Without first registration • TÜV/MOT: 2 years from first registration • Internal dimensions (LxWxH): 366 x 175 x 35 cm • External dimensions (LxWxH): 512 x 191 x 114 cm • Loading height of the floor: 79 cm • Permissible total weight: 3,500 kg • Unladen weight: 945 kg • Payload: 2,555 kg • Chassis: High loader (wheels under the body) • Tires: 185R14C • Suspension: ALKO rubber spring axle • Support wheel: Yes, automatic, 500 kg • 100 km/h approval: Optional, can be retrofitted DESCRIPTION • Unique, torsion-resistant longitudinal frame chassis for safe driving characteristics • Aluminum side panels, anodized, double-walled • All side panels foldable and removable • Steel corner posts removable • Rear flap can also be used as a swing-out flap • Insertion option at all 4 corners for tarpaulin frames, grid attachments, side panel attachments or front panel extension • Stable toggle lever locks • All-steel floor, 3mm hot-dip galvanized – extremely robust • Drawbar and frame, hollow profile construction, welded together and completely hot-dip galvanized • Numerous crossmembers, allowing for high point loads • All transverse and longitudinal supports rest on the ground • 8 foldable lashing points, recessed and mounted in the floor frame profile (600 DaN/kg) • 8 lashing eyes under the loading area • U-profile on the rear, for easier attachment of the ramps • Ramp shaft prepared • Solid 4-stage hydraulic cylinder • Electric hydraulic pump with battery (12V/75AH) in the box incl. cover • Emergency hand pump for manual tilting in case of a discharged battery • Removable remote control for electric hydraulics • Integrated battery charger with Schuko plug • Maintenance-free rubber spring axles from ALKO • Automatic reversing system • ALKO overrun device and parking brake Nedpfezy Dkkex Ac Aedb • 13-pole plug • Reversing light • Large-sized safety lighting • Integrated rear fog light • Lighting recessed in the rear frame • Reinforced, automatic support wheel for secure parking of the loaded trailer, load capacity 500kg • Premium maneuvering handle with tie-down strap winder _____ Accessories can be retrofitted by our specialist workshop! - Please feel free to ask about your desired modifications! _____ - Financing or leasing possible - Delivery throughout Germany possible - All prices include VAT - Vehicle registration document can be sent in advance or transit license plates (Germany) can be provided. - Export license plates including customs registration possible Descriptions and images are protected by copyright! Anhänger Zentrum BAUMANN GmbH Dekkers Waide 17 46419 Isselburg Over 1,200 trailers immediately available for you! We have been a specialist dealer & repair workshop for Brian James / Blyss / Debon / Humbaur / Hapert / Unsinn / Cheval Liberte / Koch / Lorries / Martz / Stedele / TPV / Tohaco / Vezeko / Variant / Vlemmix for over 30 years. - Errors, omissions and prior sale excepted -

Condition: good (used), Kistler NC joining module with dual-station/spindle unit Kistler NCFH 60 servo press with feed slide & spindle station The Kistler NCFH 60 NC joining module is integrated into an industrial dual-station/spindle unit designed for automated series production (e.g., friction welding or precision pressing). The system is characterized by exceptional precision, integrated force-displacement monitoring (piezoelectric sensor technology), and an extremely robust design capable of withstanding continuous industrial loads. Precise press-fitting and joining: Ideal for high-precision assembly processes in the automotive industry, electronics manufacturing, or general mechanical engineering. Integrated quality assurance (force-displacement monitoring): Using built-in piezoelectric sensors, the module measures the exact tensile and compressive forces acting during the pressing process in relation to position. Flexible process control: Enables advanced functions such as "joining to block," position-controlled pressing, or force-controlled joining (when combined with a suitable controller, e.g., Kistler maXYmos). Automated workpiece holding: Nedpfx Acezcpnzj Aodb The coupled spindle station features an automated clamping function (pneumatically or hydraulically actuated via integrated cylinders), making it perfect for automated series production and assembly lines. Sturdy machine bed: The entire mechanical assembly is mounted on a heavy-duty welded steel frame to withstand the immense forces (up to 6 tons per side) generated during operation. Joining module manufacturer: Dr. Staiger Mohilo+Co GmbH / Kistler Group Type: 2151B 60304002 Model: NCFH 60 400 300 B H C G Nominal force: 60 kN (equivalent to a pressing force of approx. 6 tonnes) Max. total spindle stroke: 400 mm Max. travel speed: 300 mm/s Motor type: AC hollow-shaft servo motor (165H-180E) Holding brake: 18 Nm Certification: CE marking Scope of delivery: Kistler NCFH 60 joining module including mounted flange coupling, yellow slide/feed guide, complete sensor cabling, and the associated spindle clamping station. "Everything from a single source: We would be happy to offer you suitable bank financing for your project." komplett-konzept.leasingo.de You can find more items—new and used—in our shop! International shipping costs on request!

Year of construction: 2023, condition: ready for operation (used), An unused Traub CNC twin-spindle turning and milling center with peripheral equipment is available. Spindle types 1/2: D76/D76, max. turning length: 900mm, max. workpiece diameter: 76mm, number of tool carriers: 3, control system: Traub TX8i-s V8. Main spindle bore: 76mm, taper size: 6, hollow clamping cylinder: D76/20, indexing: 2.5°, clamping pressure range: 8bar-75bar. Counter spindle bore: 76mm, taper size: 6, hollow clamping cylinder: D76/20, indexing: 2.5°, clamping pressure range: 8bar-75bar. Upper tool carrier: axes: X/Y/Z, stations: 12. Lower left tool carrier: axes: X/Y/Z, stations: 12. Lower right tool carrier: axes: X/Y/Z, stations: 12. Including Isi Elbaron RON4DHEC mist extraction and filtration system, custom-built circulation conveyor, Bürener hinged belt chip conveyor, Bürener Eco-Fluid coolant system (600l), cooling unit, coolant chiller, Traub WH workpiece handling system, various grippers and gripper pairs, IoT, and management and monitoring software. This machine was never put into operation and is therefore in as-new condition. Documentation available. An on-site inspection is possible. Ndedpfx Acjzkvkqe Aeb

Condition: ready for operation (used), Year of construction: 2015, travel distance X-axis: 260 mm, travel distance Z-axis: 590 mm, controller manufacturer: MITSUBISHI, controller model: M-730UM, number of axes: 3, This 3-axis DMG MORI NLX1500MC/500 was manufactured in 2015. It features a spindle output of 11/7.5 kW and a maximum spindle speed of 6,000 min-1. The machine is equipped with a 12-station turret and a high-pressure coolant system. If you are looking to get high-quality turning capabilities, consider the DMG MORI NLX1500MC/500 horizontal turning machine we have for sale. Contact us for further details. Ndodpjz Dt D Eofx Ac Asb - Operation Panel Type: ERGOLINE TOUCH (21.5 + 15.6)- Customer Factory Voltage: 380 V- Frequency: 50 Hz- Nominal Bed Length: 500 mm- Spindle 1 Output: 11 / 7.5 kW- Spindle 1 Speed: 6,000 min-1- Spindle 1 Through-Spindle Hole Diameter: 61 mm- Spindle 1 Chuck Type: Hollow Chuck (6")- Spindle 1 Chuck Manufacturer: Kitagawa- Spindle 1 Chuck Cylinder Stroke Check: Stroke end detection- Turret 1 Type: 12 Stations- Turret 1 Milling Function: Provided- Turret 1 Rotary Tool Spindle Output: 5.5 (3 min) / 3.7 kW- Turret 1 Rotary Tool Spindle Speed: 10,000 min-1- Turret 1 Rotary Tool Spindle Torque: 29 N·m (3 min) / 14 N·m- Turret 1 Tool Mounting Method: By bolts- Turret 1 Overhang of O.D. Cutting Rotary Tool: 100 mm (Y-axis stroke control)- Tailstock: Provided (Programmable Z-axis travel type)- Tailstock Spindle: Live Center MT4- Chip Conveyor: Provided (Right disposal type, Hinge)- Coolant System: High-pressure (635 W / 1040 W), Water-soluble coolant Technical Specification Counter Spindle No Driven Tools Yes

Condition: used, Pneumohydraulic cylinder TOX Pressotechnik Hydro-pneumatic press, power pack Type: S 04.00.050.12 D No.: 208696.460 Year of manufacture approx. 2000 Pressure capacity: 4.0 tons at 10 bar Pressure capacity: 3.0 tons at 8 bar Pressure capacity: 2.6 tons at 7 bar Pressure capacity: 2.4 tons at 6 bar Pressure capacity: 2.0 ton. at 5 bar Pressure capacity: 1.6 ton. at 4 bar Pressure capacity: 1.2 tons at 3 bar Total stroke: 50 mm Power stroke: 12 mm Piston rod: Ø 30 mm Thread for piston rod: M22 x 2 mm Compressed air requirement: 3 to 10 bar - Electronic oil pressure switch with TOX digital display for force measurement, type 167282 - Height only power pack with piston rod = 610 mm - Height of power pack hydropneumatic cylinder only = 560 mm - Additional base plate 160 x 160 x 20 mm - Plunger plate: Ø 68 mm Space requirement L x W x H: 160 x 160 x 660 mm Weight: 21 kg Ndedeu D Tz Ujpfx Ac Ajb Very good condition 3 pieces available, price per piece

Condition: excellent (used), Year of construction: 2022, functionality: fully functional, turning length: 291 mm, turning diameter: 270 mm, Like new condition; has not yet been used in production. Control system: CNC path control SIEMENS SINUMERIK 828 D TECHNICAL DATA Main spindle Njdpfxsyrd Uho Ac Aodb Turning diameter: 270 mm Turning length: 291 mm Chuck diameter: 210 mm Spindle bore: 76 mm Drive power max.: 10.5/20.0 kW C-axis (resolution): 0.001° Speed range up to: 45-4,500 rpm Turret (tool holder) Number of stations: 12 Of these, driven: 12 Speed of driven tools: 5,000 rpm Tool holder: BMT 45 X-axis: 175 mm Z-axis: 350 mm Tailstock Tailstock quill diameter: 65 mm Tailstock quill stroke: 80 mm EQUIPMENT/ACCESSORIES  Hollow cylinder for main spindle  C-axis for main spindle  Tailstock  Drive unit for turret  Coolant system  IKZ = internal coolant supply, 10 bar  Chip conveyor  Flush gun  Parts catcher  3-jaw chuck SAMCHULLY MH-208 BVI, max. diameter 210 mm, incl. set of jaws  Documentation

Year of construction: 2021, condition: new, cylinder diameter: 133 mm, Maximum Operating Pressure 700bar Njdpfx Acehhfa Ts Asdb Capacity Class (tonnage) 200 Maximum Cylinder Capacity Advance (kN)1995 Stroke (mm) 152 Collapsed Height A (mm) 430 Extended Height B (mm) 582 Outside Diameter D (mm) 247 Cylinder Bore Diameter E (mm) 190,5 Plunger Diameter F (mm) 133,4 Base to Advance Port H (mm) 57 Top To Retract Port I (mm) 96 Saddle Diameter J (mm) 133 Weight (kg) 147