Used punches for sale (59)

Year of construction: 1999, condition: reconditioned (used), Machine is currently undergoing overhaul PROCESSABLE MATERIALS Depending on material properties and sheet configuration: · Paper with a minimum grammage of 80 gsm · Cardboard or solid board up to a grammage of 2,000 gsm · Corrugated board up to a total thickness of 4 mm (max. sheet curvature 4%) PERFORMANCE DATA Max. sheet format: 820 x 1,130 mm Min. sheet format: 350 x 400 mm Max. cutting force: (400 t) 4.0 MN Max. machine speed: 9,000 sheets/h Standard equipment of the machine: Feeder Non-stop high-performance sheet feeder W3 equipped with: • Automatic non-stop device • Automatic pallet changeover • Suction head • Double-sheet detector • Motorized stack side correction • Motorized suction head adjustment • Conveyor table with pneumatic cover frame • Compressed air and vacuum pump Register Table • Operator-side side lay, switchable between pull and push mode • Light sensor for accurate side alignment of sheets • Fine adjustment of the side lay • Two active front lays with light sensor for register control • Two inactive front lays for sheet stabilization • Separate fine adjustment of gripper edge for drive and operator side • LED display for accurate front and side lay registration • Trend display for sheet detection • Sheet rejection, disabling only the feeder • Height-adjustable top lay for positive sheet guidance Die-cutting station Lodpfjyuuzdsx Al Isrn • Roller-guided support rails for the chase • Roller guide for die-cutting plate on swing-out support arms • Motorized die pressure adjustment • Automatic device for lifting the chase to the platen • Electronic die-cutting force display with max. pressure limitation • Vacuum device in sub-table for thin cutting plates Stripping Unit • Frame drive and frame lift for upper tool frame • Mount for the stripping board with centerline fine adjustment • Device for sample sheet removal • Upper tool frame • Lower tool frame Delivery • Fully automatic pile stacker, pre-selectable • Counted sub-stacks with automatic insertion of uncut sheets • Can form sub-stacks (interleaved sheets between 250 gsm – 800 gsm) • Frame lift for upper tool frame • Mount for change frames with electric adjustment in running direction • Pneumatic frame locking • Switchable gripper opener cam and sheet ejector • Sheet jogging device • Integrated conveyor belt for gripper edge or waste grid removal (double-cut) • Separator sheet magazine with electronic level control, refillable from B-side during production • Tool frame with centerline • Change frame for standard pile delivery / gripper edge removal • Change frame for blank separation grid • Mounting kit for separation punch • 8 x sheet hold-downs for standard pile delivery • 4 x cross support bars Options: • QTM – Patented guide rails • QTM – Chase with quick lock system and X/Y adjustment • QTM – Upper stripping frame with quick lock system • QTM – Upper delivery frame with quick lock system • Control upgrade to latest Siemens S7 controller • New generation frequency converters • Modem for remote service connection • Machine height increase: 900 mm

Condition: good (used), functionality: fully functional, machine/vehicle number: 552410, Year of construction: 1974, Manufacturer: Bobst, Switzerland Model: Autoplatine SP 1420 E – 600 T Type: Die Cutting Machine / Autoplatine Year of manufacture: 1974 Machine No.: 552410 Technical specifications: - Max. sheet size: 1420 x 1020 mm - Min. sheet size: 700 x 500 mm - Speed: up to 4,500 sheets/hour - Power supply: 380 V, 50 Hz Features: Lrjdpfow Rb Ezox Al Isn - Robust construction for carton and corrugated board - Automatic platen die cutting - Pile feeder and delivery - Mechanical control with operator panel - Proven Swiss quality

Condition: good (used), functionality: fully functional, machine/vehicle number: 057400108, Manufacturer: Bobst, Switzerland Model: SP 142 Machine Category: Die Cutting Machine Machine Type: Autoplaten Year of Manufacture: --- (not specified) Machine Number: 057400108 Lrjdpfxsw Rb Ebs Al Ien Technical Specifications: - Max. Sheet Size: 1420 x 1020 mm - Min. Sheet Size: 700 x 500 mm - Speed: up to 4,500 sheets/hour (depending on job) - Power Supply: 380 V, 50 Hz Features: - Robust Swiss design - Mechanical control with side operator console - Pile feeder and delivery for continuous operation - Suitable for cartonboard and corrugated board - Proven model for packaging production

Condition: excellent (used), Year of construction: 2014, functionality: fully functional, machine/vehicle number: 858799A, Manufacturer: Ruiyang Printing Machinery Co., Ltd., China Model: MH-1650 Ljdpfx Alsw Rb Ipo Iern Machine Category: Die Cutting & Creasing Machine Machine Type: Automatic Large Format Die Cutter Year of Manufacture: 2014 Serial Number: 858799A Technical Specifications: - Max. Sheet Size: 1650 x 1210 mm - Min. Sheet Size: 650 x 550 mm - Max. Die Cutting Size: 1620 x 1190 mm - Speed: up to 3,200 sheets/hour - Power Supply: 380 V, 50 Hz, 3 phases Features: - Automatic feeder with suction head - Large format pile delivery - Heavy-duty design for carton and corrugated board - Control panel with management and safety functions - Suitable for large format packaging production

Year of construction: 1990, operating hours: 21,834 h, condition: ready for operation (used), functionality: fully functional, machine/vehicle number: 059700605, Bobst SP 142-CER from 1990 for sale – Reason for sale: replacement investment made. The machine can be inspected in production. Dismantling and transport at buyer's expense. Lrodpfx Aoy Htxgsl Isn

Condition: ready for operation (used), Available directly from our warehouse in Son; Ledpexz Niujfx Al Iorn heavy stamping die with electric coupling, electrical system completely renewed around 2019, original year of manufacture 1973; mechanically completely overhauled in 2015, moving die resurfaced, die and gear pins replaced with new pins with significantly higher mechanical strength than the originals, as well as the bronze bearings now made from material grade 2.1061 DIN 1705; this material is extremely wear-resistant with the addition of Pb (lead) for improved performance and good emergency running properties (i.e., no lubrication required), stamping plate 144 x 104 cm, thickness 5mm. Electrically upgraded with PILZ safety relays for each channel, motorized clamping of the stamping die. Safety bars have been extended and made more robust compared to the original design, 350 tons of pressure.

Year of construction: 1991, condition: good (used), functionality: fully functional, machine/vehicle number: 8061, Iijima’s excellent high-speed JF-1030, built in 1991, modified for Bobst die-cutting tools. Machine number 8061 Year of manufacture: 1991 Die-cutting head adapted to be compatible with/for Bobst die-cutting punches and retaining strips. More modern LEUZE photoelectric sensors in the front and side guides. LEUZE ultrasonic detection with teach-in function. Sector segment driven by a double set of bevel gears instead of the previous triple system. This results in smoother, vibration-free operation of the gripper carriages. Chains replaced in May 2023. Gripper carriages have been overhauled where necessary, but not replaced. Current tolerance on the front guide for rigid cardboard is < 0.15 mm. Clutch (electric 24 VDC, Warner) replaced in May 2023, as well as all roller bearings on this shaft, including those in the pressure plate just before and after the worm gear. Oil seals replaced. Oil reservoirs flushed and thoroughly cleaned before switching from mineral oil to fully synthetic oil. Absolutely no foam formation, quieter operation. Decommissioned on 23/12/2025; available for sale ex-warehouse Van Rooij from that date. For the end user: can be delivered including installation, transport and warranty. Other specifications according to the factory brochure. Technical Specifications – Flatbed Die-Cutting Machine Materials • Paper from 80 g/m² • Solid fibre board / cardboard up to 2000 g/m² • Corrugated board up to 4 mm, depending on material quality and cutting layout --- Sheet Sizes & Formats • Maximum sheet size: 750 × 1050 mm • Minimum sheet size: 350 × 400 mm • Maximum cutting form size: 745 × 1070 mm • Maximum cutting surface: 730 × 1030 mm • Inside chase dimension: 750 × 1050 mm --- Performance • Maximum cutting pressure: when running max. sheet size 300 metric tons • Maximum speed: up to 8,500 sheets/hour • Gripper margin: adjustable 8 - 12 mm • Normal cutting rule height: 23.80 mm --- Pile Data Feeder pile • Height (incl. pallet): 1,500 mm • Weight (incl. pallet): 1,000 kg Delivery pile • Height (incl. pallet): 1,380 mm • Weight (incl. pallet): 1,000 kg Auxiliary piles • Feeder auxiliary pile height: 450 mm • Feeder auxiliary pile weight: 450 kg • Delivery auxiliary pile height: 800 mm • Delivery auxiliary pile weight: 800 kg --- Machine Dimensions & Weight • Length without feeder: 4,540 mm • Length with feeder: 5,810 mm • Width: 2,350 mm • Height: 2,100 mm • Weight of machine: 15,000 kg • Weight of feeder: 1,000 kg --- Electrical & Air Requirements • Power supply: 3-phase AC • Main motor output: 15 kW • Connected load of machine: 32.4 kVA • Compressed air required: 6 bar • Air intake volume requirement: approx. 30–50 l/min Lrjdpfx Aox Ndu Dol Isn --- Additional Information • Heavy-duty industrial construction • Designed for continuous professional die-cutting production • Specifications subject to alteration

Condition: used, This Krause C64-50 Autofeed Die Cutter is a powerful machine designed for precise and efficient die cutting work. With a maximum format of 600 x 500 mm, it offers the flexibility to handle a wide range of materials. The machine is currently located in the Netherlands and is standing still, which represents an ideal opportunity for those looking for a high-quality die cutting machine. Lrsdpfx Asvfx Ulel Isn Format: 600 x 500 mm Equipment: Krause autofeed die cutter Max. Size: 60 x 50 cm (23 x 19 inch)

Condition: used, Year of construction: 1993, Punching die Size 100x140 Year of manufacture 1993 Lrsdpfjy Szztex Al Ijn

Year of construction: 2020, condition: ready for operation (used), A barely used foil die-cutting and embossing machine Kama with integrated hot foil stamping is available. Die-cutting force: 165t, max. sheet format X/Y: 760mm/600mm, min. sheet format: 279mm/210mm, max. die-cutting format X/Y: 743mm/585mm, production speed: 5500sheets/h, gripper margin: 10mm, min. paper weight: 100g/m², max. cardboard weight: 1500g/m². Machine dimensions X/Y: approx. 5000mm/2700mm/2750mm, weight: approx. 6000kg, operating hours: approx. 1000h. Including Kama AutoRegister, vacuum pump, compressor and servo main drive. Documentation available. An on-site inspection is possible. Lodpfoy Nnaksx Al Iorn

Condition: reconditioned (used), Year of construction: 1968, functionality: fully functional, machine/vehicle number: 7923278, type of input current: three-phase, total width: 2,440 mm, total length: 3,320 mm, total height: 2,130 mm, overall weight: 8,200 kg, input frequency: 50 Hz, input current: 30 A, nominal power: 7.5 kW (10.20 HP), rotational speed (max.): 4,600 rpm, rotational speed (min.): 1,500 rpm, space requirement width: 2,440 mm, 72x102 cm die cutter for thin paper and light carton up to 600 gsm. Exceptionally stable and very silent fast cylinder press. Floor anchoring is not necessary. Lrodpfox Hzm Sjx Al Ijn

Condition: used, Year of construction: 1959, The Heidelberg OHT, manufactured in 1959, is a machine with an A4 format. It is currently in production and located in Germany. The delivery terms are FCA. Format: A4 Equipment: Lsdpfevfxwtex Al Iern Letter Press Tiegel - DIE Cutter Punching force 40 tons Size min.: 40 x 70 mm Standard chase: 260 x 340mm Speed min.: 2.200 sph - max. 5.500 sph

Condition: used, Year of construction: 1973, The Heidelberg OHT, manufactured by Heidelberg in 1973, is a robust machine designed for printing and die-cutting operations. With a format of A4, it is currently in storage in Germany. Identified by the machine number T 184634 H, this press has a punching force of 40 tons and can handle a minimum format of 40 x 70 mm. It operates at a speed ranging from a minimum of 2,200 revolutions per minute to a maximum of 5,500 revolutions per hour. The machine includes a skeleton chase of 260 x 350 mm and a standard chase of 260 x 340 mm, with a maximum format of 260 x 380 mm. It comes complete with accessories and a closing frame, and features a letterpress platen and a die-cutting platen. The delivery condition is FCA. Format: A4 Speed: 5500 Power: 380 V 1,25 KW Net Weight: 1100 KG Measurements: L1,68 x B1,24 x H1,85m Equipment: Skeleton chase: 260 x 350mm Speed min.: 2.200 sph - max. 5.500 sph Size max. 260 x 380 mm Letter Press Tiegel - DIE Cutter Punching force 40 tons Lsdpfx Asvfxu Eel Iorn Size min.: 40 x 70 mm Complete with tools and accessories include frame Standard chase: 260 x 340mm Machines No T 184634 H

Condition: ready for operation (used), Year of construction: 2019, operating hours: 15 h, machine/vehicle number: MP.DBDO-00198, Size 75 x 106 cm, non-stop function in feeder and delivery, integrated fine adjustment of the cutting plate, motorized die-cutting pressure adjustment, simple operating concept. The basic model is already equipped with all functions and equipment required to start production. Short makeready times, high flexibility thanks to an extended range of materials, accommodates smaller die-cutting tools. Machine number: MP.DBDO-00198, Impressions: 15 million. Lodsyhn Uqopfx Al Iern

Condition: used, Year of construction: 1966, functionality: limited functionality, Automatic die-cutting machine, Bobst SPO 1575 EEG, ref. 2994 Year – 1966 Maximum sheet size – 1055 x 1575 mm Minimum sheet size – 400 x 600 mm Maximum mechanical speed – 4500 sheets/hour Lodpey Hxw Iofx Al Ijrn Maximum pressure – 350 t Vacuum feeder Stripping unit Gripper-edge waste removal Batch delivery Sold as is, still in production Available from the end of July 2026 Price: only 12,000 EUR – must be sold as soon as possible.

Condition: good (used), Year of construction: 2003, functionality: fully functional, machine/vehicle number: 7555605, Max size: 60 x 41 cm, integrated feeder SE - 18.2, cross-web paper cutter ST - 18.2, die cutting unit D - 18, strapping/banding unit PB - 18.1, horizontal and vertical strapping. Paper width min. 35 x 45 mm, paper width max. 405 x 600 mm. Stacking height min. 30 mm, stacking height max. 100 mm. Machine no.: 7555605 Lrsdpfxoxc Uv Aj Al Ien

Condition: excellent (used), Year of construction: 1968, functionality: fully functional, machine/vehicle number: 32250, Size 64 x 90 cm, for diecutting only, excellent condition Machine no.: SBDS32250 Lrjdpfx Aow Inz Dol Ijn

Condition: good (used), Year of construction: 1997, Bobst SPO 160S + Bobst Flexo 160 – 3-color, ref. 3006 The line consists of: – Bobst Easyloader – 3 x Bobst 160 flexo units with vacuum transfer – sheet transfer system – Bobst SPO 160S – delivery stacker Maximum sheet size – 1600x1100mm Maximum output – 5500 sheets/hour Lrsdpfjy U D Nxjx Al Ien

Year of construction: 1966, operating hours: 10,000 h, condition: excellent (used), functionality: fully functional, outer diameter: 420 mm, machine/vehicle number: 58256, Nebiolo Saturnia in very good condition. From first owner, at first used as a letterpress in the upcoming market with offset in the 70's. The company always produced with it's offset to maxima 50/70 size. Situated as a local printer in a village, the Nebiolo was sometimes used for rilling, slitting, scoring some offset jobs. very good machine, low noise, excellent condition of al mechanical parts. Airpump for feeder and delivery is for a later make = Becker dry-pump 100m3 with low noise. All parts necessary for the machine come with the machine, even as the original operational book and spare-parts book. The cylinder has a 6 cm larger diameter than a KBA Condor and it weights 800kgs, only 200 kgs less of that of a heidelberg SBB/SBD. Lodpotyyvwjfx Al Iorn The delivery is different and for carton better that that of its competitors: a triple drum delivery, turning the front side up again on the belts which transport it to the pile. Best is to replace the individual belts for one large belt and make some extra attention for laying the sheets down when coming from the belt with better air facilities. Of course we can arrange that for you either. Then you have a faster, very easy to operate and maintain with better productivity and at least the same durability (with lower noise-level due to less moving parts) than an heidelberg SBD with approx the same size for more than double the money. Really a nice product from Nebiolo even as it big brother Urania. They have pull-lays but can easily turn over to push side lays. Some specs: Max paper size 650 x 950 mm Min paper size 300 x 420 mm Speed 1500 - 4000 imp/hour Feeder pile height 550 mm Delivery pile height 650 mm Impression force approx. 35000 N (not adjustable in lighter or heavier, only one value) Bearer height 24,85 mm; machines needs "normal - Bobst standard" 23,80 diecut forms/lines with a hardened steel plate under the form so that small compensations could be made with thin band and paper under this hardened plate. This is the only and best method. A 45 to 47 HRC plate will be delivered with the machine, even as a new cylinder jacket. Feeder and delivery use an additional extern pump, Becker, 100m3, 2kW Size of the machine (approx, with steps) L x W x H = 330 x 220 x 190 cm Weight net 4,800 kgs

Year of construction: 1968, operating hours: 35,000 h, condition: good (used), functionality: fully functional, machine/vehicle number: 7723238, 72x102cm two revolution die cutter for thin paper and light carton up to 600 grs/m2. excellent stable and very silent fast cylinder press. Locking to the floor is not necessary. Lrodpfx Aljtyy Sfo Ijn Price is for each machine, NOT for the package. Package is 15% discount. Two identical machines available from the same shop, both with the same specs and the same state of maintenance. As a kind of specialist in these type of machines, I have delivered machines to this company which already had one, so at certain moment they produced with 4 machines and 6 or 7 Heidelberg Cylinder presses at half the size. maintenance always carried out by my company, so both machines have a known history, which is good. As a result of shrinking industry in The Netherlands and different types of shivering/perforating/scoring on offset presses with the cutting plates, the company went to a smaller building and only kept one Condor. In my opinion the best, fastest and strongest letterpress ever, built in this size, for sure! With less parts than a Heidelberg SBD and running much smoother. As a result of my cooperation with the KBA factory and particular Mr. Hans Bernhard Bolza-Schünemann who is the engineer responsible of the several new innovative constructions in the Condor, a small sized Condor (65x95cm) in very good original condition as a complete printing press, with some ""patina"" was donated to the Leipzig -er Museum für Printkunst (June 2002), because of its importance for the development of the printing industry in the 60's.

Year of construction: 1997, condition: excellent (used), functionality: fully functional, machine/vehicle number: 052302303, Bobst Easypress 142, for the format 102x142cm to carry out models, test punching, preparation work for the production machine. excellent condition, year of construction 1997 Lrodpfx Aouk I Nxsl Ion

Condition: ready for operation (used), Very well-known and reliable Cauhe die-cutting machine, format 1200x1600 mm, year of manufacture 1996, from second owner. Lrsdpfxjxz Ncbj Al Ien

Condition: used, URANIA DSK Lrsdpfew R Eqbex Al Ion Maximum paper size: 80 × 112 cm Minimum paper size: 30 × 42 cm • Frame opening (normal): 78.5 × 108.5

Year of construction: 1963, condition: used, functionality: limited functionality, machine/vehicle number: 512804, 1963 Bobst SP900E with double action stripper in reasonable/good condition. Well-maintained.. in recent years for example sprocket wheels, main gripper chains, counterplate under cuttingplate, cardan joints to the feeding head, have been renewed (original Bobst parts) Lrjdotyqizepfx Al Ion Gripperbars have not been renewed recently, they are still in quite a good condition. The knee joints have almost no signs of wear. they were probably at some point and the machine has not been used much since then. There is hardly any screech on them. Machine is dismantled in our storage in the South of The Netherlands, dismantled and not under power. For seriously interested potential buyers we will further upgrade the machine and assemble it and give the possibility to test it inevery way they want. In that case price will be 22,000 euros, loaded on to your transport, EX SITE

Condition: ready for operation (used), functionality: fully functional, Rotary die cutter in very good condition, hardly used. Lrsdpfxoxz Tn Uj Al Ijn Contact details of a highly reputable die manufacturer can also be provided.