Used Deflection Pulley for sale (677)

Condition: good (used), Lubricating bolt for rope pulley, steel rope pulley, rope deflection pulley, crane rope, four-rope multi-shell grapple, polyp grapple, mechanical multi-shell grapple, shell grapple, ship unloading grapple, scrap grapple, garbage grapple, rope grapple, digging grapple, bolt crane bolt Lubrication bolt: Crane bolt type M48 -Shaft: Ø 69.5 mm -Number: 3x crane bolts available -Price: per piece Hedpfx Asv Ikt Eebpop -Dimensions: Ø 92 x 345 mm -Weight: 13.2 kg/piece

Condition: good (used), Rope lock for rope pulley, steel rope pulley, rope deflection pulley, crane rope, four-rope multi-shell grapple, polyp grapple, mechanical multi-shell grapple, shell grapple, ship unloading grapple, scrap grapple, garbage grapple, rope grapple, digging grapple -Crane rope lock: Ø 22 mm .: 1031 4124 Hodpfov Iluwox Abpjp -Type: ETL914-23g P.09 MKrane -Hole: Ø 40 mm -Dimensions: see photos -Number: 12x cable lock available -Price: per piece -Dimensions total: 275/130/H85 mm -Weight: 8.4 kg/piece

Condition: good (used), Lubricating bolts for rope pulleys, steel rope pulleys, rope deflection pulleys, crane ropes, four-rope multi-shell grabs, polyp grabs, mechanical multi-shell grabs, clamshell grabs, ship unloading grabs, scrap grabs, garbage grabs, rope grabs, digging grabs, bolts, crane bolts, lubricating bolts -Grease bolt: Crane bolt type 75x145 M48 -Shaft: Ø 59.6 mm -Number: 7 bolts available - Price: per piece - Dimensions: Ø 80 x 170 mm -Weight: 3.9 kg/pc. Hedev Illcepfx Abpjp

Condition: new, empty load weight: 1,093 kg, maximum load weight: 2,407 kg, overall weight: 3,500 kg, axle configuration: 3 axles, loading space length: 5,500 mm, loading space width: 2,240 mm, color: black, construction height: 1,000 mm, working width: 2,320 mm, Comfort package: Electrically tiltable / electric winch / aluminium rims / sloping rear / continuous ramp / perforated lashing floor / electric wheel / floor dust box, hydraulics, automatic reverse, drive-on ramp, hot-dip galvanizing, * IMMEDIATELY AVAILABLE * Comfort package: Electrically tiltable / electric winch / aluminium rims / sloping rear / continuous ramp / perforated lashing floor / electric wheel / floor dust box Technical data: - Make: Brian James - Model: T Transporter 231 - Vehicle type: Car transporter - Vehicle condition: New vehicle - Initial registration: Without initial registration - TÜV/HU: 2 years from initial registration - Internal dimensions (LxWxH): 550 x 224 x 0 cm - External dimensions (LxWxH): 710 x 232 x 100 cm - Loading height of floor: 59 cm - Perm. Total weight: 3,500 kg - Unladen weight: 1,093 kg - Payload: 2,407 kg - Chassis: High loader (wheels under the body) - Tires: 195/55R10C aluminum rim - Chassis: ALKO rubber spring axle - Support wheel: Yes - 100km/h approval: Optional, can be retrofitted DESCRIPTION - Original aluminum rims 10-4.5J, anthracite - Perforated steel lashing floor offers high slip resistance and is extremely wear-resistant, even under the toughest operating conditions. - Additional sloping rear end ensures a particularly low drive-on angle - Vehicle can also be fitted with all options after purchase: enormous potential for retrofitting. - Very sturdy welded steel frame - Storage compartments embedded in the loading area for drive-on ramps at the rear - Continuous drive-on ramp, + additional ramps, foldable, adjustable (heavy-duty) - Loading area, front wooden floor (instead of ramp shafts at the front) - Sliding contact edge for drive-on ramps for different track widths - Comfort package for professional use consisting of: - electrically operated tipping function incl. cylinder - very fast tipping of the loading area - for very flat drive-on angle - battery with 12V power supply is installed in the vehicle - electric cable winch, Warn 8000Cable winch, Warn 8000 - 3600 kg pulling force - Electric winch equipped with radio remote control and steel cable as well as central deflection pulley - CTEK battery charger - Lockable floor storage box with spring-loaded lid - Hole pattern of galvanized steel lanes - Numerous lashing points and a heavy-duty floor offer flexible lashing options and perfect grip. - Side panels color: black - Additional lashing options thanks to side railing - Removable railing all round: The multi-part side profile railing offers numerous lashing points and is removable so that wider loads can be transported. - Frame completely hot-dip galvanized - Spare wheel mounted on the drawbar for easy access - Automatic reverse drive - ALKO overrun device and parking brake - Cast steel coupling head with integrated ALKO high-security lock - Very stable V-drawbar REINFORCED - 13-pin plug - Reversing lights - Large LED safety lighting - Complete LED lighting: Extremely bright, durable and reliable. - dynamic LED indicators are clearly visible even in bad weather - robust protection for the rear lights - integrated rear fog light - various front, side and rear marker lights - heavy-duty support wheel - 5-year chassis warranty New vehicle with warranty and TÜV. We are happy to offer you suitable financing !, Descriptions and pictures are protected by copyright !!! Over 800 trailers immediately available for you! For over 30 years we are Brian James / Humbaur / Hapert / Unsinn Hjdpfxju Hrzre Abpep

Condition: ready for operation (used), Year of construction: 2016, machine/vehicle number: 306533, functionality: fully functional, cutting height (max.): 350 mm, cutting width (max.): 610 mm, overall weight: 550 kg, saw band length: 4,700 mm, TECHNICAL DETAILS Deflection pulley diameter: 630 mm Tool dimensions: 13 x 0.65 x 24 TPI Saw band length: 4,700 mm Loading height: 1,065 mm Cutting height: 350 mm Cutting width without rip fence: 610 mm Cutting width with fence: 150 mm Cutting speed: 10 - 100 m/min Table travel: 600 mm Table feed speed: 0.03 - 0.3 m/min MACHINE DETAILS Extraction connection diameter: 1 x 120 mm + 1 x 100 mm Hedpeyzy Drjfx Abpjp Required air velocity: minimum 25 m/s Required air volume flow: 1,725 m³/h Dimensions & Weight Dimensions (L x W x H): 1,850 x 1,200 x 2,300 mm Machine weight: 550 kg Motor power: 0.75 kW Operating voltage: 400 Volt / 50 Hz Power supply: 3 x 400 Volt Fuse protection: maximum 16 Amperes Minimum cross-section: 1.5 mm²

Condition: new, power: 350 kW (475.87 HP), fuel type: diesel, overall weight: 26,000 kg, axle configuration: 3 axles, color: white, gearing type: automatic, total width: 2,550 mm, total height: 3,850 mm, Year of construction: 2025, Equipment: ABS, air conditioning, electronic stability program (ESP), navigation system, ++ RENT ++ BUY ++ RENT ++ BUY ++ RENT ++ BUY ++ RENT Internal Number: #487 Mercedes-Benz Arocs 6x2 BL with combined high-pressure jetting and suction-pressure tank body with water recycling KROLL Type K 1.0-13.0/29 P Body by KROLL Fahrzeugbau-Umwelttechnik GmbH * HOSE STORAGE CASSETTE WITH SIMULTANEOUS TELESCOPIC BOOM DN 125 * Reach on pivot side: 5,200 mm * Tank material: S355J2+N (St. 52.3) * Water recovery system * Telescopic piston with 3 locking positions * (3,300 l water / 10,600 l sludge, 5,500 l water / 8,200 l sludge, 7,700 l water / 6,000 l sludge) * Suction from open bodies of water possible "Comfort version" via cassette boom with integrated filter * EMPTYING: via pneumatically operated piston * SLUDGE WATER DRAIN DN 80: for pushing back wastewater through the boom into the sewer * Manhole DN500 Chassis Mercedes-Benz Arocs * 2548 BL 6x2 * Powershift 3 * 476 HP / 350 kW * EURO 6e Hodjvh H Ewopfx Abpjp * Fuel capacity 510 l * Cab color MB 9147 Arctic White * 2x LED beacons on cab * Rear-view camera * Navigation * Air conditioning Vacuum system * Samson Truck Master 2,500 approx. 2,465 m³/h at 400 bar * Drive: flexible, via drive shafts, V-belts, and pneumatically engageable friction clutch from the vehicle PTO * Approx. 20m HD hose DN 125 * HOSE STORAGE CASSETTE WITH SIMULTANEOUS TELESCOPIC BOOM DN 125 * Reach on pivot side: 5,200 mm * Additional suction hose reel with suction right rear, approx. 30m DN80 suction hose High-pressure system * Uraca P 3-45 approx. 345 l/min at 205 bar * Drive: flexible, via drive shafts, V-belts, and pneumatically engageable friction clutch * Approx. 240m HD hose DN 25 * Large HD hose reel for 240m 1'' DN 25, 180° swiveling * Equipped with 240m DN25 * Small HD hose reel for 80m (DN 13 hydraulic) * Equipped with 60m DN13 Special features * Hose storage cassette with telescopic boom DN 125 * Infinitely adjustable height of suction hose hydraulically via roller guide carriage * Boom arm for suction hose hydraulically and telescopically extendable and can be swiveled 180° * KROLL water recycling system WRS1 with self-cleaning function * Pressure and speed control * Spray gun * LED beacons * LED perimeter lighting * Remote-control operation of work functions via CAN-BUS system * Radio remote control CAN * Hand washing station (warm) * Rear-view camera with 7'' color monitor incl. day/night switching * Soundproof enclosure for pump compartment * LOW WATER WARNING SYSTEM: with buzzer in main control cabinet and automatic pump shut-off * RESIDUAL WATER DRAINAGE: pneumatically for all water-carrying components, connected to the truck compressed air system * Large equipment box and hose trays * Toolbox * Holder for traffic cones * Vice * Ladder * Electric winch * Mount for fall protection device * Pulley for "banana" / deflection unit * Large advertising panels on both sides * Manhole DN500 Technical data Gross Vehicle Weight 26,000KG * Unladen weight approx. 19,800 KG * Length 9,880mm * Height 3,890mm * Width 2,550mm * Wheelbase 4,200mm For further detailed information and/or pictures, please contact us directly. A large selection of other vehicles for SALE or RENT can be found on our website. Subject to changes, prior sale, and errors. The buyer is obliged to independently confirm the condition and equipment of the goods. Sale is exclusively subject to our terms and conditions and under excl...

Condition: new, maximum load weight: 37,075 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete range of vehicles, including immediately available and short-term delivery vehicles, on our website. Sample of the equipment. Full equipment details available on request. Neck (Gooseneck): * Gooseneck with front corners bevelled approx. 45° and rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading Platform: * Loading area behind the gooseneck hydraulically liftable and lowerable, length approx. 2,800 mm, with rear bevel approx. 1,000 mm x 8° * 6 pairs of external foldable lashing rings (LC 5,000 daN) * 2 pairs of external foldable lashing rings (LC 10,000 daN) * 1 pair of internal foldable lashing rings at the central beam front (LC 10,000 daN) * Cut-outs in the outer frame of the platform for hooking in tensioning straps (LC 2,000 daN) * Grating flooring C40/4 (point load approx. 2.3 t over an area of approx. 20 x 20 cm), treadplate flooring over the axles Two-piece Steel Ramps: * One pair of galvanized two-piece steel ramps, approx. 2,750 + 1,400 x 800 mm, with grating surface C40/4 (point load approx. 2.2 t over an area of approx. 20 x 20 cm) * Ramp with hydraulically folding ramp sections * Hydraulic lift unit, hydraulically adjustable * Maximum load per pair: approx. 40,000 kg Landing Legs: * JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lift capacity (approx. 50 t test load) Axles: * BPW axles and suspension, 2 fixed axles, 1 self-steering axle Hsdpfeyhkrrsx Abpop * Technical axle load: 12,000 kg each * Electromagnetic reversing lock automatic via reverse gear and manual activation * Air suspension with lift and lower valve Braking System: * WABCO braking system in compliance with EU regulations with EBS-E (2S2M) Tyres: Tyres 235/75 R 17.5 3PMSF – make at our discretion TPMS: * TPMS tyre pressure monitoring system according to ECE R 141 Paintwork: * HRM metallisation of the complete vehicle chassis with ZINACOR 850 (85% zinc / 15% aluminium) to ensure maximum corrosion protection * Final coating with 2 layers of 2K topcoat, single-coloured in RAL 3002 Carmine Red as per RAL System 841GL * Rims in silver grey Accessories included: * 2-inch king pin * Galvanized steel front wall approx. 400 mm high * Grating in the gooseneck bevel C30/3 (point load approx. 2 t over an area of approx. 20 x 20 cm) * Grating in the platform bevel C40/4 (point load approx. 3.4 t over an area of approx. 20 x 20 cm) * Electric-hydraulic unit at the rear under the platform * Plug-in aluminium side and rear boards on the gooseneck, approx. 2,440 x 400 mm (L x H). Rear galvanized insert stanchions removable. (Body length approx. 2,560 mm) * Electric winch with radio remote control, approx. 5,400 kg lifting capacity, including approx. 9.5 mm thick steel cable, approx. 24 m long, with cable guide roller * Bolted approx. 5 t ring for winch cable loop on the neck without deflection pulley * One galvanized toolbox integrated in the sloped gooseneck with opening for a winch * Grating on the gooseneck C30/3 (point load approx. 2 t over an area of approx. 20 x 20 cm) * 7 pairs of stanchion sockets for plug-in stanchions, approx. 100 x 50 mm, in the outer frame of the platform * Lift axle on the front axle, controlled by TEBS E depending on actual axle load and current loading status * 7 pairs of recessed lashing rings along the central beam (LC 5,000 daN): 2 pairs in the lift bed, 5 pairs in the rear section of the platform

Condition: new, maximum load weight: 37,075 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete range of vehicles, including those available immediately or at short notice, on our website. Excerpt from the equipment list. Full equipment details available on request. Gooseneck: * Gooseneck with front corners beveled approx. 45° and rear taper approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN). Hardwood floor approx. 30 mm thick Loading area: * Loading area after the gooseneck hydraulically liftable/lowerable, length approx. 2,800 mm, with rear taper approx. 1,000 mm x 8° * 6 pairs of folding outward lashing rings (LC 5,000 daN) * 2 pairs of folding outward lashing rings (LC 10,000 daN) * 1 pair of inward folding lashing rings at the front central beam (LC 10,000 daN) * Cutouts in the external frame of the loading area for attaching tension belts (LC 2,000 daN) * Grating surface C40/4 (point load approx. 2.3 t on an area of approx. 20 x 20 cm), over the axles checker plate Two-piece steel ramps: * One pair of galvanized two-piece steel ramps, approx. 2,750 + 1,400 x 800 mm, with C40/4 grating (point load approx. 2.2 t on an area of approx. 20 x 20 cm) * Ramp with hydraulically folding in/out ramp sections. Hydraulic lift system, hydraulically adjustable * Maximum load per pair: approx. 40,000 kg Landing gear: * JOST landing gear (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles and suspension, 2 rigid axles, 1 self-steering axle * Technical axle load: 12,000 kg each * Electromagnetic reverse lock via reverse gear and manual activation Hedpfx Asyhkqzjbpjp * Air suspension with lift and lower valve Brake system: * WABCO brake system according to EU regulations with EBS-E (2S2M) Tyres: 235/75 R 17.5 3PMSF – Manufacturer of our choice TPMS: * TPMS tire pressure monitoring system in accordance with ECE R 141 Paintwork: * HRM metalizing of the entire vehicle chassis with ZINACOR 850 (85% zinc / 15% aluminum) for optimal corrosion protection * Final paint in 2 coats of 2K topcoat, solid color in RAL 3002 Carmine Red in accordance with RAL system 841GL * Rims in silver grey Including accessories: * 2-inch kingpin * One galvanized steel front wall, approx. 400 mm high * Grating in the gooseneck taper C30/3 (point load approx. 2 t on an area of approx. 20 x 20 cm) * Grating in rear taper of the loading area C40/4 (point load approx. 3.4 t on an area of approx. 20 x 20 cm) * Non-slip sand paint on the checker plates above kingpin and loading area * Electro-hydraulic unit at the rear under the loading area * On the gooseneck: plug-in aluminium side walls and rear wall, approx. 2,440 x 400 mm (L x H). The rear galvanized drop-in stakes are removable. (Body length approx. 2,560 mm) * An electric cable winch with radio remote control, approx. 5,400 kg pulling force, including approx. 9.5 mm thick steel cable, approx. 24 m long, with cable guide pulley * Bolted 5 t ring for cable winch deflection on the neck without deflection pulley * One galvanized toolbox integrated in the beveled gooseneck with opening for a winch * Grating on the gooseneck C30/3 (point load approx. 2 t on an area of approx. 20 x 20 cm) * 7 pairs of stake pockets for plug-in stakes approx. 100 x 50 mm in the outer frame of the loading area * Lift axle on the front axle with control via TEBS E depending on current axle load and loading condition * 7 pairs comple...

Condition: new, - NEW -The model for more comfort. The edge sanding machineRS 2010 with its versatile equipment offers edge grindinga complete processing for the carpentry quick changeover from freehand sanding to veneer sanding,the band oscillation and the stepless swiveling of theGrinding aggregates allow universal support table, which is pneumatically adjustable in height, and thepneumatic belt tensioning ensure easy hnical Equipment:- Pneumatically height-adjustable work table- Infinitely swiveling sanding unit up to 45 °- easy conversion to veneer edge grinding- pneumatic belt tension- Display 0 - 45 ° for the sanding unit- stable support table on the pulley- feed bracket- Angle and miter fence- Veneer grinding device- Table on the deflection roller adjustable by spring pressure- stepless aggregate donation 90-135° via hand wheel- oscillationTechnical specifications:Motor power: 3 kWBelt speed: 22 m / sBand length: 2760 mmBand width: 200 mmTable size: 450 x 920 mmRequired space: 1200 x 2000 mmExtraction: 120 &amp, 80 mmTotal weight: approx. 320 kgStorage location: 97447 Gerolzhofen- free loaded- Hedsvwf Hxspfx Abpsp

Condition: used, Pulley Diameter 700mm Max sawblade width 35mm Table size 980mm x 700mm Max blade length 5120mm Table Tilting 0 to 35 degrees Throat capacity 600mm Max. Cutting height 350mm Adjustable rip fence 4 Hp motor and starter Weight 435kg Hsdpfx Abszd Uuhspop

Condition: good (used), Year of construction: 2017, Multi-Sheet Machining For Maximum Output Automatic Loading System CNC Bandsawing, Routing & Drilling CNC Control Of The Bandsaw Movement +/- 90 Degrees The MZ Pluris is recognised as the machine of choice for all sofa and chair frame manufactures. The machine can work with OSB, Plywood, MDF, Chipboard (good quality), solid wood and also some composite materials. It has a number of key advantages over standard CNC nesting machines that include the possibility to stack multiple sheets high eg 5 x 12mm thick sheets, thanks to the use of the bandsaw sheet yield is much better, no vacuum is used so the machine is able to cut small shaped parts without difficulty and lastly cut parts are coming off on to the side discharge conveyor as the machine is still working, thus maximising machine output. Increased working capacity of 2550mm 1550mm Sheet size = 1220 x 2,440mm (8' x 4 ') and 1525 x 1525mm Standard equipment / features: CNC bandsaw specification - Maximum depth of curve 800mm - Minimum radius of cut 50mm - Maximum cutting height 100mm - Automatic angling of blade +/- 90 degrees - Blade size 5900 x 13mm - Automatic sawblade tensioning - Cast aluminium saw pulleys 900mm dia - Self braking motor 11kw CNC router specification: - Maximum working height / cutting depth 60mm - Electro spindle power S6 9KW - Variable rotation speed 7000 - 24000 rpm - HSK 63F tool holder Fence / grippers / supports: - Programmable pusher fence with 6 x pneumatic panel grippers - 8 x panel support arms General: - Automatic centralised lubrication system consisting of 3 x oil pumps - Internal conveyor belt for removal of dust / waste cuts - Free standing electrical control cabinet with PC and keyboard - Hand held remote control CNC vertical drilling unit: - Maximum drilling depth 70mm - 5 x independent drilling spindles in line. (Drills not included). - 1.7kw motor Plus package: - 5 position automatic tool changer - Automatic movement of clamps and support arms - set through the program Lifting table: - 4 screw - Capacity 2550 x 1525mm - Max load capacity 3000kg approx - Max panel pack height 700mm - PIT REQUIRED Year - 2017 CE Serial nr - 22/2017 Hsdpfx Abstqfv Iepjp

Condition: excellent (used), Year of construction: 2019, functionality: fully functional, pressing force: 225 t, stroke length: 200 mm, table length: 4,100 mm, overall weight: 15,000 kg, Equipment: safety light barrier, Fully Serviced Bystronic CNC Pressbrake Available for Purchase A high-quality, pre-owned Bystronic Xact Smart 225/4100 hydraulic downstroke CNC pressbrake is currently available for sale. This 2019 machine is fully serviced, operational, and ready for immediate deployment. Key Technical Specifications Hsdpfjzg Nq Njx Abpep Manufacturer: Bystronic Model: Xact Smart 225/4100 Year of Manufacture: 2019 Bending Capacity: 225 tons Bed Size / Working Length: 4,100 mm (4 metres) Control System: ByVision touchscreen CNC control Total Axis Configuration: 7 axis total, featuring a 5-axis backgauge (X, X1, R, Z1, Z2) Crowning: Hydraulic deflection compensation Installation Requirement: Free-standing design; no foundation pit required Core Advantages High Precision: The 5-axis backgauge and hydraulic crowning ensure exact bending angles across the entire 4-metre bed length. User-Friendly Interface: The intuitive ByVision touchscreen control simplifies setup and reduces programming time. Cost-Effective Installation: The free-standing configuration eliminates the need for expensive floor excavations or pits. Feel free to let us know if you would like us to draft a formal quotation for you

Condition: used, Pulley Diameter 700mm Hsdpfx Abswl H Daspop Max sawblade width 40mm Table size 765mm x 1000mm Table Tilting 0 to 35 degrees Throat capacity 680mm Max. Cutting height 485mm Adjustable rip fence 4 Hp motor and starter DC brake Serial number 80210

Condition: excellent (used), fuel type: electric, color: other, lifting height: 11,100 mm, Year of construction: 2023, operating hours: 531 h, Drive: Track Empty weight: 2.400 kg Dimensions (LxBxH): 299 x 73 x 160 cm Length of jib: 10,4 m Lifting capacity: 2.800 kg Supply voltage: 48 V CE mark: yes Technical condition: very good Visual appearance: very good Hsdpfx Abow A S E Depop = Additional options and accessories = - Lifting hooks = Remarks = General Country of production: Italy Condition CE type: CE Radio remote control, Winch with double pulley hookblock and ball hookblock, 1000 kg Hand Jib, Extending undercarriage

Condition: good (used), Variator pulley, Vario adjustment pulley, Vario belt pulley, PIV gearbox, Vario gearbox, variable speed pulley, variable pulley, expansion pulley, V-belt pulley adjustable -Manufacturer: Lenze, Vario belt pulley with compression spring -Type: Simplabelt 11.213.016 -Outer pulley diameter: 160 mm Hodpfx Abowz U Ulopop -Diameter of the inner socket: 18 mm -Dimensions: Ø160 x 110 mm -Weight: 3.4 kg

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 900 kg, oil tank capacity: 1,300 l, power: 75 kW (101.97 HP), year of last overhaul: 2025, For sale is a overhauled Bollegraaf baler, with 100 tonnes pressing force, large bale format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding system Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Hjdpezdn H Rofx Abpop Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: reconditioned (used), Year of construction: 2015, operating hours: 30,143 h, functionality: fully functional, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 570 kg, overall weight: 20,000 kg, oil tank capacity: 600 l, power: 37 kW (50.31 HP), year of last overhaul: 2025, volume flow: 800 m³/h, Technical data baler: Manufacturer Presona AB, Sweden Type LP 60 VH1 Year of construction 2015 Total operating hours, 30,143 hours, as of July 2025 Effective pump running time onl 6,527 hours, as of July 2025 Number of pressed bales 115,193 bales, as of July 2025 Press force pre press 25 t Main press force 60 tonnes Specific pressing force 73N/cm² Dimensions of feed chute 1,500 x 1,100 mm Filling volume / pressing cycle 2.7 m³ Theoretical throughput capacity 800 m³/hour Throughput capacity under operating conditions 350 m³/hour Bale dimensions 1,100 x 750 mm Drive power 37 kW Tying 5-fold vertical, fully automatic Throughput capacity with a Bulk weight of 50 kg/cbm 11 to 14 tonnes/hour Bale weights 420 to 570 kg, depending on material Hydraulic oil tank volume 600 litres Baler dimensions assembled with hopper 10,100 x 3,750 x 4,310 mm (l x w x h) Transport dimensions excluding press 10,100 x 2,400 x 3,000 mm (l x w x h) Machine weight press approx. 20 tonnes Condition of the press: The press was partially overhauled in our workshop and then tested in manual and automatic mode. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Grease cartridges of the automatic roller lubrication system replaced Slide rails cut out from the press floor in the press room Underbody reinforced with welded sheets New HARDOX slide rails welded in Wire station with deflection rollers for the lower wire cleaned and made operational Slide rails cut out from the floor in the press channel Hodpfxszdny Rs Abpjp New HARDOX slide rails welded in Both side walls of the press channel dismantled, derusted Worn side wall plates cut out Complete side walls covered with new wear plates and welded Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Machine checked, general maintenance work carried out and press tested in manual and automatic mode Comments: The press is sold without a conveyor belt and without wire stations. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2012, operating hours: 25,895 h, functionality: fully functional, pressing force: 78 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 24,000 kg, oil tank capacity: 1,000 l, year of last overhaul: 2025, volume flow: 410 m³/h, Technical data baler: Manufacturer Presona AB Typ LP 80 VHK 1 Year of construction 2012 Total machine operating hours 25,895 hours, as of July 2025 Pump operating hours, effective 14,135 hours, as of July 2025 Number of bales pressed 235,597 pieces, as of July 2025 Press power main press 78,5 tons Specific press capacity 95 N/cm² Press power of pre-press 28 tons Volume of pressing chamber 2,7 m³ Feed channel1,500 x 1,100 mm Theoretic throughput rate 930 m³/h Throughput rate under operating conditions 410 m³/h Bale size 750 x 1,100 mm Driving motor 55 kW Tying system 5 fold vertical, 3-fold horizontal, full automatic Throughput rate with a bulk density of 30 kg/m³ approx. 9 to 12 tonnes/hour, depending on material 50 kg/m³ approx. 14 to 17 tonnes/hour, depending on material 100 kg/m³ approx. 16 to 25 tonnes/hour, depending on material Throughput capacity with MSW (Municipal Solid Waste) approx. 20 to 27 tonnes/hour, depending on material Bale weight 450 up to 600 kg, depends on material and bale length Volume hydraulic oil tank 1,000 l Baler dimensions built up with hopper 10,985 x 3,750 x 4,310 mm (l x w x h) Transport dimensions only baler 10,985 x 2,300 x 2,900 mm (L x w x h) Machine weight baler approx. 24 tons Condition of the press: The machine was partially overhauled and serviced in our workshop and, once the work was complete, tested in manual and automatic mode during operation. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Wire station with deflection rollers for the lower wire cleaned and made operational Side guides removed from the press ram, smoothed, mounted and readjusted Main hydraulic cylinder dismantled and disassembled for inspection Hedpfx Abozdnxgepjp Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical and horizontal needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Door contact switch checked and partially replaced. Emergency stop switch checked. Complete electrical wiring checked and partially replaced. Bearings of the wire guide rollers under the press replaced. New safety grilles for vertical and horizontal binding manufactured and installed. Machine checked, general maintenance work carried out and press tested in manual and automatic mode Scope of delivery: Only the baler will be sold. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Year of construction: 2019, condition: ready for operation (used), overall weight: 300 kg, total width: 730 mm, total height: 1,585 mm, laser power: 300 W, This 3-axis ALPHA LASER ALM 300 was manufactured in 2019. It features a powerful Nd:YAG laser with an average power of 300 W and a peak pulse power of 9 kW. The movement range is 120 × 110 × 800 mm, allowing for versatile applications. If you are looking to get high-quality laser welding capabilities, consider the ALPHA LASER ALM 300 machine we have for sale. Contact us for further details. • Laser type / wavelength: Nd:YAG, 1,064 nm • Operating mode: Pulsed • Average power: 300 W • Peak pulse power: 9 kW • Pulse energy: 90 J • Pulse duration: 0.5–20 ms • Pulse frequency: Single pulse up to 100 Hz • Welding spot diameter: 0.2–2.0 mm • Focusing objective: 150 mm (further lenses per lens data sheet) • Work area / axes: Hsdpfezf A Ifjx Abpsp • Movement speed (X/Y/Z): 0–25 mm/s • Movement range (X/Y/Z): 120 × 110 × 800 mm • Lowest working point: 530 mm • Highest working point: 1590 mm • Arm deflection: 1300 mm • Observation lens / ergonomics: Microscope attachment with eyepieces for glasses wearers 10× • Electrical connection: 3 × 400 V / 50–60 Hz / 3 × 16 A • Condition: Demo/showroom use only; excellent technical and visual condition

Condition: new, Year of construction: 2025, New machine Year of manufacture 2025 Edge sanding machine with integrated dual conveyor feed system for solid wood parts, veneered edges, and curves, featuring oscillation of the entire sanding unit. Processing of solid and veneered edges either manually or with automatic feeding: - On the veneer sanding side, along the two stop plates (with infeed stop including integrated extraction slots and fine adjustment according to removal scale) onto the elastic sanding pad (oscillating for uniform use of the graphite lining, including grit compensation adjustment and belt tension relief via two deflection rollers), with infeed stop extension, table size 1180 x 325 mm. Manual processing of straight and curved solid wood parts: - On the solid wood sanding side against the continuous, glide-backed sanding belt support, table size 1180 x 325 mm including miter fence with scale. - On the front side with an optionally quick-mountable semicircular table (with dust extraction holes) against the rubberized belt drive roller Ø 90 mm, support radius 300 mm. - On the drive roller, optionally with a quickly mountable auxiliary cast iron table (with dust extraction holes) 400 x 500 mm on an oscillating spindle for use of sanding drums Ø 25, 30, 40 and 45 x 100 mm for external and internal curves, with spindle safety cover. Design: Robust machine frame with heavy cast iron tables, sanding unit motorized height adjustment up to 120 mm and tiltable up to 45° without any table adjustments (patented construction), belt drive motor 3 kW (4 HP), 400 V/50 Hz, with motor protection switch, separate motor for belt oscillation, oscillation stroke programmable from 10 - 90 mm, control box integrated in frame, constant belt tension with length compensation, belt tracking adjustable, safety guard, dust extraction via two extraction hoods, flexible hoses and common internal pipe to 150 mm connection, recess in frame for easy transport with pallet or forklift, belt width 150 - 200 mm, belt length 2000 mm, working height 830 mm (solid sanding table) or 900 mm (veneer sanding table), net weight 750 kg, footprint 1150 x 800 mm. Feed system: Integrated in the frame, two parallel transport belts 50 mm wide, spaced 250 mm apart on the underside, 20 mm wide top pressure rollers, 0.55 kW (0.75 HP) motor, continuously adjustable speed 3 - 15 m/min. COMFORT version Kündig UNIQ-S Including table extension UNIQ/UNIQ-S/Flash Including upper extraction duct UNIQ without slide Including semicircular table for belt drive roller UNIQ-S Hodpfx Aew Tfx Djbpsp Availability: short-term Location: Flörsheim

Condition: new, Year of construction: 2024, New machine Year of manufacture: 2024 Robust drilling machine featuring a powerful OPTIMUM brushless drive. Key highlight: menu-guided control for operating modes drilling/tapping. - Smooth-running and high-performance brushless drive - Optimal power transmission via aluminium pulleys combined with a toothed GATES quality V-belt - High running smoothness thanks to precision-ground multi-spline drive - Concentricity guaranteed at less than 0.015 mm, measured at the quill - Drilling spindle with precision ball bearings - Membrane keypad; dust- and water-resistant, easy to clean - High-quality OPTIMUM quick-action drill chuck included as standard - Separate emergency stop pushbutton - Precisely machined worktable with diagonal T-slots, 360° rotatable - Integrated coolant channel surrounding the worktable - Large, height-adjustable safety guard with interlock switch for maximum operator protection - Drilling depth stop - V-belt guard with safety switch - V-belt tensioning mechanism - Solid, large base plate with reinforced ribs at the rear Technical specifications: Column diameter: 60 mm Dimensions (LxWxH): approx. 552 x 445 x 850 mm Hsdjw Rhk Rjpfx Abpop Weight: approx. 64 kg Drilling capacity (steel): 18 mm Continuous drilling capacity (steel): 16 mm Tapping capacity (steel): M10 Table size: 230 x 245 mm Speed range: 100 – 6000 rpm Number of speed ranges: 5 Total power connection: 1.5 kW Mains voltage: 230 V Quill stroke: 65 mm Spindle taper: MT 2 Throat depth: 130 mm Including quick-action drill chuck 1–13 mm Including machine vice BMP 100 Availability: short-term Location: Flörsheim

Condition: used, mileage: 544,877 km, power: 310 kW (421.48 HP), first registration: 07/2017, fuel type: diesel, overall weight: 18,000 kg, axle configuration: 2 axles, next inspection (TÜV): 04/2026, brakes: retarder, color: blue, gearing type: automatic, emission class: euro6, Year of construction: 2017, Equipment: ABS, air conditioning, electronic stability program (ESP), parking heater, Vehicle No.: 143-26 Mercedes-Benz 1842 Actros COC paper available! * RETARDER * Wheelbase 3,700 mm * Bi-Xenon headlights * 1 x bunk bed Hjdpfozc Srcox Abpjp * Air conditioning * Tire tread approx. 50-60% * Cool box * Turning assist * Differential lock * German vehicle Driver's side airbag, Audio system: CD radio (Bluetooth), Bi-Xenon headlights, Compressed air connection in the cab, Air horn, Cab: with air suspension, Tinted windshield, Notebook holder, Info display 12.7 cm with additional display, Integral rear, Fuel tank: 390 L aluminum, Cool box / refrigerator, Air intake behind cab, Air deflection system on the roof (lockable) and on the side, Mounting plate / saddle plate 24 mm for fifth wheel coupling, Engine brake reinforced, Auxiliary drive MB 123-10c, On-board unit for toll collection, Frame lowering without bellows residual pressure control, Frame height lowered by 25 mm, Tire pressure control system, Retarder, Interface fleet management system, Drawers under dashboard, Fuse box, Seats in the cab: Driver's seat comfort suspension seat, Sun visor outside, Steel rims 11.75x22.5 (on front axle), 12V socket in the passenger footwell, 24V / 25 A socket in the passenger footwell, 24V socket in storage compartment on the right, Oil cooler for transmission Additional features: Emission standard EURO 6, Axle configuration: 4x2, Front axle load 7.5 t, Actros 4, Trailer socket 24V / 15-pole, Work lights, Exhaust pipe to the right outside, Exterior mirrors electrically adjustable and heated, Differential lock rear axle, Compressed air tank steel, Compressed air unit medium, Driver assistance system: Attention-Assist (fatigue detection sensor), Driver assistance system: Brake Assist (Active Brake-Assist), Driver assistance system: Lane Keeping Assist, Cab: Width 2.30 m, Cab: L StreamSpace, Cab floor with engine tunnel 170 mm, Suspension: Leaf spring / air, Suspension: Front spring seat aluminum, Suspension: Front leaf springs 7.5 t, 1 leaf, Electric windows, Generator 100 A, Gearbox 12-speed - Type: G 211-12, Urea tank (AdBlue): 60 L, Rear axle bevel gear 440, Body / superstructure: Semi-trailer tractor, Lower comfort bunk, Comfort locking system, Communication interface, Mudguards 3-part, Radiator grille, Steering booster regulated, Air compressor 2-stage, Engine 12.8 L - 310 kW R6 diesel (OM 471), Engine compartment encapsulation, Wheelbase 3700 mm, Ramp mirrors, Waste heat recovery, Disc brakes front and rear axle, Seat cover / upholstery: fabric, Seats in the cab: Co-driver functional seat, Seats in the cab: Driver's seat backrest foldable, Voltage converter 24V / 12V 10 A, Splash guard front, Stabilizer front axle, Storage compartment outside left, Socket cab 24V, Tachograph / EC control device, Door extension for cab, Underbody cladding aerodynamically shaped, Underrun protection front, Preparation CB radio, Preparation toll collection, Front axle curved, Water pump regulated, Permissible total weight 18.00 t, Auxiliary heater (water) Inspection possible during our opening hours, test drive by appointment! In the case of export sales, a deposit will be retained, which will be refunded after receipt of the proof of destination. Company logos or advertising logos on the vehicles may have been digitally edited in the photos. No guarantee is given for the functionality of the extras. All information without guarantee - Errors, changes, typing errors and prior sale reserved. Vehicle descriptions are explicitly not legally binding.

Condition: good (used), Year of construction: 2014, cutting range 300 mm capacity 90 degrees: flat 330 x 260 mm capacity 90 degrees: square 260 x 260 mm capacity 45 degrees: round 260 mm capacity 45 degrees: flat 270 x 200 mm capacity 45 degrees: square 250 mm capacity 60 degrees: round 180 mm capacity 60 degrees: flat 170 x 170 mm capacity 60 degrees: square 180 mm automatic feeds 9999,9 mm feed minimum 2.0 mm cutting diameter minimum 5.0 mm band speed 15 - 100 m/min vice 340 mm Öffnung dimensions of saw-band 3650 x 27 x 0,9 mm Control MEP CNC total power requirement 2.2 kW weight 1240 kg range L-W-H 1800 x 1900 x 1750 mm actual NEW price about 23.000 Euro special price on request Equipment: - robust electro-hydraulic fully automatic band saw (INDUSTRY) - with additional semi-automatic function, for cuts from 0° to 60° left - WINDOWS “CE” based MEP 50 – control and 7” touch screen display * simple and quick setting of all machine parameters * with additional soft keys + backlit display * 10 programs, each with a maximum of 9999 pieces and . a maximum length of 9999.9 mm - material feed with stepper motor via ball screw * single stroke 600 mm repeatable to saw any length * accuracy of ± 0.1/600 mm - feeder with protective cover and safety limit switch - precise setting of the cutting feed with indication in mm/min - positioning of the saw head and movement of the feeder using a joystick - automatic detection of the start of the cut - large deflection discs, adjustable from cast steel - Saw blade tension with blade tension control and display - Hard metal blade guides for maximum cutting precision - Automatic monitoring of the cutting load - Vice with quick adjustment * with interchangeable clamping and stop jaws - Large, laterally extendable chip tray and coolant container * equipped with 2 electric pumps for lubricating and cooling the saw blade * Coolant gun for cleaning the machine - Chip removal brush for cleaning the saw blade - Operating instructions DE Information from the manufacturer: When installing this saw in a network with a residual current device (FI), this should be universally current sensitive and not less than 300 mA. Hedpezc Rv Hefx Abpop

Condition: reconditioned (used), 1 pair of PERSKE flat motors, 5.5 kW each, well suited for pre-cutting circular saws in front of band saw lines, one with a right-hand thread and one with a left-hand thread, rated continuous power 5.5 kW, with new ball bearings, with 2 steel brackets (left and right) for mounting 1 KATT circular saw flat motor, 11 kW / 1450 rpm, flange Ø 200 mm, right-hand thread, second shaft stub for hydraulic pump drive with 150 mm Ø pulley, tested and fitted with new bearings, suitable e.g. for PAUL 27 AO cross-cut saw Hjdeuqk Azepfx Abpop

Condition: used, mileage: 272,250 km, power: 324 kW (440.52 HP), first registration: 06/2013, fuel type: diesel, overall weight: 26,000 kg, axle configuration: 3 axles, color: orange, gearing type: mechanical, emission class: euro6, Year of construction: 2012, Equipment: ABS, air conditioning, ++ RENT ++ BUY ++ RENT ++ BUY ++ RENT ++ BUY ++ RENT Internal Number: #480 MAN TGS 26.440 6x2 with KROLL High-Pressure Jetting and Suction Body with Water Recovery WRS2 Body KROLL Fahrzeugbau-Umwelttechnik GmbH * Type K 1.0-13.0/29 P * HOSE STORAGE CASSETTE WITH SIMULTANEOUS TELESCOPIC BOOM DN 125 * Maximum reach on pivot side: 5,200 mm * Tank material: S355J2+N (St. 52.3) * Water recovery system * Telescopic piston with 3 locking positions * EMPTYING: via pneumatically operated piston * SLUDGE WATER DRAIN DN 80: for returning dirty water through the boom into the sewer. * Water compartments on the sides Chassis MAN TGS * 26.440 6x2 * manual transmission * EURO 6 * Fuel capacity approx. 400 l * Driver’s cab color: Municipal Orange RAL 2011 * 2x LED beacon lights on the cab * Reversing camera * Air conditioning Vacuum system CVS WR 3100, approx. 2,465 cbm/h at 400 bar * Drive: flexible, via drive shafts, V-belts, and pneumatically operated friction clutch from the vehicle engine’s PTO. * approx. 20m HD hose DN 125 * HOSE STORAGE CASSETTE WITH SIMULTANEOUS TELESCOPIC BOOM DN 125 * Maximum reach on pivot side: 5,200 mm High-pressure system Uraca P 3-45, approx. 345 l/min at 205 bar * Drive: flexible, via drive shafts, V-belts, and pneumatically operated friction clutch. * Large HD hose reel for 240m 1" DN 25, swivels 180° * Equipped with approx. 200m DN25 * Small HD hose reel for 80m DN 13, hydraulically operated * Equipped with approx. 60m DN13 Special features - hose storage cassette with telescopic boom DN 125 * Infinitely variable height adjustment of suction hose via hydraulic roller guide carriage * Suction hose boom, hydraulic operation and telescopic, swivels 180° * KROLL water recovery WRS2 * Water spray gun * LED beacon lights Hodpfx Abowwf S Tepop * LED work area lighting * Work functions remotely operated via CAN-BUS technology * Radio remote control * Reversing camera with 7" color monitor * Soundproof enclosure in pump area * Large tool and hose storage boxes * Toolbox * Holder for traffic cones * Vice * Pulley for banana/guide device * Large advertising boards on right and left For further detailed information and/or photos, please contact us directly. You can find a wide selection of further vehicles for PURCHASE or RENTAL at: Subject to changes, prior sale, and errors. The buyer is obliged to independently verify the condition and equipment of the goods. Sale exclusively pursuant to our general terms and conditions and under exclusion of any warranty. Special equipment: Front axle load 9.5 t, elevated exhaust pipe on right, co-driver bench seat, rear axle differential lock, ETA circuit breaker, flame-start device, heavy-duty roll stabilization, automatic climate control, trailing axle NOL-08 steered, liftable, PTO NMV221, beacon (2), external sun visor, fleet management system control module, reinforced front axle shock absorbers, preparation for engine start/stop system at end of frame.