Used Cutting Shears for sale (14,775)

Condition: used, Technical data paper roll cutting machine. This machine can only be used for small residual rolls up to a maximum diameter of 400 mm in order to automatically unwind these residual rolls and cut the paper into strips so that it can be better pressed into bales. Manufacturer unknown Type unknown Year of manufacture unknown Dimensions feed table for rolls: Width inside of rolls 2.195 mm Height inside of castors 465 mm Transport dimensions Feed table over all: 2,650 x 1,300 x 2,150 mm (W x H x D) Dimensions roller cutter: Width cutting shaft inside 2.250 mm Transport dimensions of the roll slitter over all: 3,050 x 1,550 x 550 mm (W x H x D) Rjdpfx Aaju Tg Sps Usp Remarks: There are no further data or documents available. A viewing is possible by appointment. We assume no liability for the technical data and possible errors.

Condition: excellent (used), Plasma cutter SAF Nerta Zip 20-40 A Type 0408_2240 380 Volt 10/18 A 220 Volt 16/30 A Cutting current 20/40 A Transport dimension : Length 700 mm width 430 mm height 970 mm Weight 90 kg Rsdpfjvdqkvsx Aa Ujp

Condition: used, functionality: fully functional, Equipment: CE marking, angle stop, centralized greasing system, documentation/manual, emergency stop, finger protection, foot remote control, safety light barrier, type plate available, LVD Shear Type HSL 40/12.7 Capacity 4x12 mm Year 1991 Weight 14,000 kg Rjdsykk Acopfx Aa Uep

Condition: used, Year of construction: 1997, open-circuit voltage 280 - 320 VDC current intensivity 30 - 80 A output voltage 140 VDC cutting medium Air / Nitrogen total power requirement ca. 11,2 kW weight of the machine ca. 40 kg dimensions of the machine ca. 0,90 x 0,35 x 0,50 m Plasma Cutting Machine HYPERTHERM - Hypertherm Powermax 1100 ERTHERM RT 80 hand torch - Recommended cutting capacity: 22 mm - Maximum cutting capacity: 29 mm - Severing capacity: 38 mm Rsdpfx Aaoym D Ano Usp - Gas: Air or nitrogen - Gas inlet pressure: 6.1 bar - Gas flow rate: 189 l/min

Condition: like new (used), Year of construction: 2020, functionality: fully functional, Machine has very low hours Rodpfjv Iaqyjx Aa Ujp

Condition: excellent (used), Year of construction: 2011, Prima Industrie Platino 1530 laser cutting machine only 4300 hours cutting hours This Prima Industrie Platino 1530 laser cutting machine 4,0kW CO2 was manufactured in Italy in the year 2011 and installed at the end of 12/2011. PRIMACH 20 L control unit. Rjdpfx Aaoivg Hgj Usp

Year of construction: 2000, condition: used, Punching machine Noble Rsdpfx Ajg Dgyxoa Uep HM 35/350 BKE 200/5 Maximum pressure 35 T 5 mm sheet thickness at 40 kp/mm²

Condition: excellent (used), Year of construction: 2005, Mechanical guillotine shears Fab. Petersen Machinery Type. Cidan HSM-F 20/3 Year 2005 Technical data Make: CIDAN Type: HSM-F 20/3 Sheet width: 2050 mm Sheet thickness: 3 mm Cutting angle 2° Connection 400V / 20A Dimensions: approx. L 2.60 x W 1.60 x H 1.40 Weight: approx. 1.5 tons Rjdpfxou Utaij Aa Ujp Equipment - Man. Backgauge 750mm - Continuous hold-down device with hard rubber strip - Angle fence - Extendable support table All information without guarantee. A demonstration is possible at any time in our showroom.

Condition: excellent (used), Year of construction: 1994, Hydraulic guillotine shear Fab. HACO Typ. HSLX 3000x6/8mm Year 1994 Technical data Make: HACO Type: HSLX 3006 / 8 Year of manufacture: 1994 sheet width: 3050 mm sheet thickness: 6 mm / 8 mm on 1000 mm sheet length cutting angle: 0.5 - 3 number of strokes: 9/17 drive motor: 11 kW number of hold-downs: 18 pcs. space requirement: approx. 3,7 x 1,7 /additional lay-on arms) x 1,6 mm Machine weight: approx. 6 t Equipment - autom. cutting angle adjustment - Automatic cutting gap adjustment Rodelp Nrbepfx Aa Usp - Cutting line illumination - Support arms - Knife with 4 cutting edges - Cutting length limitation - CNC backgauge 705mm adjustment range 705 mm - angular stop - Instruction manual All data without guarantee. A demonstration under power is possible at any time in our exhibition hall.

Condition: used, Year of construction: 2009, sheet thickness steel (max.): 4 mm, back gauge: 750 mm, cutting length (max.): 2,550 mm, Motorized Guillotine Shear Manufactured by Durma, Type MS 2500 x 4 mm Year of Manufacture: 2009 Technical Specifications Manufactured by DURMA Type: MS 2504 Year of Manufacture: 2009 Rodpfev Rntzox Aa Uep Sheet Thickness: 4 mm Cutting Length: 2,550 mm Cutting Angle: 1°30' Stroke/Min: 42 Motor: 7.5 kW Backgauge: 750 mm Dimensions: L 3.15 x W 1.75 (plus support arms 0.6 m) x H 1.33 m Weight: 3.3 t Features - Controlled backgauge 750 mm - Support arms - Angle stop - Manual cutting gap adjustment - Foot switch - Operating instructions All information is provided without guarantee. A demonstration is available at any time in our showroom.

Condition: ready for operation (used), sheet thickness steel (max.): 6 mm, workpiece length (max.): 4,100 mm, - CNC frontgauge; 2 plate supports: one fixed: can feed plate into the machine, max 4000 mm one mobile: can feed plate into the machine, max 2000 mm CNC backgauge CNC blade angle setting Rodpfsyiguijx Aa Usp CNC blade clearance setting Plate support system Conveyor belt Scrap container (for first cut) Ideal machine for cutting large sheets as well as small strips! Max sheet thickness inox: 5 mm Backgauge: CNC Siemens Evacuation system: yes

Condition: ready for operation (used), ByPump 50 APC - Pump output: 55 000 psi 2 cutting heads, each with drill unit cutting cap: 200 mm with shuttle table with automatic cleaning system with container for abrasive material (max 2 ton) cutting speed: 35 m/min Rjdpoyigupefx Aa Uop positioning speed: 6084 m/min X-travel: 4000 mm Y-travel: 2300 mm max workpiece height: 230 mm Touchscreen control Software included Spare parts included Power: 52,5 kW Workarea: 4020 x 2100 mm Number of jets: 2x Software: ByVision

Condition: excellent (used), Year of construction: 2008, Beam on: 21,660 h Laser on: 42,130 h Rjdoxfim Ispfx Aa Uop

Condition: used, Year of construction: 2009, sheet width 4050 mm plate thickness 6.50 mm thickness at "Niro-steel" 4.00 mm back stop - adjustable 1000 mm work height max. 880 mm no. of strokes 6 - 11 Hub/min Control SC 70 cutting angle 0.5 - 3.0 ° down holder 23 Stück engine output 11.0 kW weight of the machine ca. 7500 kg range L-W-H 4950 x 1950 x 1720 mm Machine made from light metal production (ALU) good condition including special accessories such as sheet metal holding device - in checked condition - machine video - ?v=pv7RRijDXJA Furnishing: - electro-hydraulic/blade-guided guillotine shears - HACO CNC control model SC 70, swiveling at the front left * Pre-selection positioning of the backgauge * Digital display of actual position value * electro-hydraulic cutting angle adjustment * electro-hydraulic cutting gap adjustment * programmable retraction from the backgauge * Programmable cutting length limit * Emergency switch - electro-hydraulic cutting gap adjustment - electro-hydraulic cutting angle adjustment - electro-motorized back gauge, on ball screws - hydraulic hold-down devices - front finger protection - Ball rollers in the support table Rsdpfx Aoxaccroa Uep - 1x side stop, with mm scale - 1x freely movable foot switch - rear guard - original operating instructions including CE declaration Special accessories included: - pneumatic sheet metal holding device for thin sheet metal blanks * for sheet thicknesses up to max. 4.0 mm * optimal positioning of thin sheets

Condition: used, Year of construction: 1999, sheet width 3060 mm plate thickness 8.0 mm thickness at "Niro-steel" 6.0 mm distance between columns 3100 mm down holder 16 Stück no. of strokes max. 10 - 15 Hub/min oil volume 160 ltr. cutting angle 1.6 ° back stop - adjustable 6.0 - 750 mm Control ELGO P9521 total power requirement 18.5 kW weight 6300 kg range L-W-H 3900 x 2300 x 1630 mm Features: - Robust electro-hydraulic swing beam shear - ELGO digital display model P9521, for electric backgauge * Backgauge travel X = 750 mm * Backgauge-free ball screw drive * Travel speed 100 mm/s - 1x stable side stop * With T-slot, flip-stop, and millimeter scale - 2x stable front support arms - Electric cutting length limiter Rodpfx Aoxaci Eea Uop * Cutting length limiter to increase the stroke rate/min. - Manual cutting gap adjustment * Centrally operated on the right side stand - Front support plates - Front finger/interference guard - Inching operation with push buttons on the left control panel - Protective grille = safety device behind the machine - Operating instructions (PDF)

Condition: used, Year of construction: 2000, sheet width 3060 mm plate thickness 6.0 mm thickness at "Niro-steel" 4.0 mm distance between columns 3100 mm down holder 16 Stück no. of strokes 20 Hub/min oil volume 160 ltr. cutting angle 1.6 ° Control ELGO Number of working hours ~ 1.100 h total power requirement 11.0 kW weight 5250 kg range L-W-H 3800 x 1940 x 1560 mm from a maintenance workshop with only approx. 1.100 operating hours (!!) Equipment: - electro-hydraulic swing beam shears - ELGO NC control unit * for electric back stop Rodexacfaepfx Aa Ujp * Input of target/actual position value possible - NC electro-motoric back stop * travel path of back stop X = 750 mm * back stop ball screw with no play * travel speed 100 mm/sec - electric cutting length limitation * cutting length limitation to increase the number of strokes/min. - manual cutting gap adjustment, via eccentric - tip operation with push buttons on the control panel on the left - front support plates with ball rollers - front finger/interference protection - 1x side stop with T-slot & millimeter scale - 2x front support arms - original operating instructions including CE declaration

Condition: good (used), Year of construction: 2003, Trumpf Trumatic L3020 Co2 Laser Fully working condition - removed from working factory Working Range X axis - 3000mm Y axis - 1500mm Z axis - 115mm Overshoot range X axis - -16- +88 Y axis - 19 - +61 Rjdpfst H Iv Rjx Aa Ujp Z axis - - 2 - +16 Max Travel range X axis - 3104mm Y axis 1580mm Z axis - 117m Control - Trumpf CNC Control based on siemens sinumerik 840D Electrical Connections with TLF 3200 - 73 kVa Fuses (at 400v) - 125A Speed - Max. positioning speed, Parallel to axis - 60m/min Simultaneous - 85m/min Accuracy - smallest programmable increment. Positioning accuracy - +0.1mm Repeatability - +0.03mm Max laser power in cw mode with TLF3200 - 3200W Max material thickness - 20mm

Condition: excellent (used), Grinding diameter capacity ~80 mm (Type 2H) Type 2HA variant Redpfx Ajxrvgzoa Usp ~120 mm Maximum in-feed grinding length ~200 mm Maximum through-feed grinding length ~300 mm (with normal guides) Grinding wheel diameter 400 mm Grinding wheel width 200 mm Grinding wheel bore 203.2 mm (8") Driving wheel diameter 254 mm Driving wheel width 200 mm Driving wheel bore 127 mm Main drive motor 11 – 22 kW Driving wheel motor ~1.1 kW Driving wheel speed ~10 – 200 rpm (continuously variable) Machine weight ~3,000 kg Footprint / Dimensions ~2,400 × 1,550 mm Voltage 380 V / 50 Hz / 3-phase Extras & Features Hydraulic dressing and trueing devices for both grinding wheel and driving wheel Variable speed drive on the regulating/driving wheel Base flange, support bridge, shims, and additional accessories included in many units The “2HA” variant extends capacity to 120 mm diameter parts. We have two of these machines available.

Condition: used, Year of construction: 1993, functionality: fully functional, machine/vehicle number: 551A 117, total width: 4,900 mm, total length: 6,100 mm, overall weight: 4,500 kg, type of input current: three-phase, input voltage: 400 V, input frequency: 50 Hz, pressure: 8 bar, cutting length (max.): 4,600 mm, BOTTERO LAMILINEA 551A - Year 1993 Max cutting length: 4600 mm Air cushion power: Minimum 200 mm water column Processable thickness range Monolithic: 3 - 10 mm Laminated: 3 + 0.38 + 3 (33-1) minimum, 8 + 4.56 + 8 (88-12) maximum Maximum carriage speed: 40 m/min - Max. cutting tolerance: +/- 0.5 mm Overall dimensions: 4900 x 6100 mm Weight: 4500 kg Working table height: Adjustable from 900 up to 940 mm Rodpfx Aasyntq Ro Ujp Installed power: 18 KVA Compressed air max. consumption: 500 NL/min

Condition: used, functionality: fully functional, Year of construction: 2007, Punching machine, barely used, weight: 8500 kg. Lot includes steel cabinet with contents. Contents consist of tooling, spares and miscellaneous small parts. Rjdpfx Aaoxzpuwj Usp

Condition: new, thread dia. M6 - M36 turning speeds 30 - 150 U/min working area max. 1200 R angle adjustable from - to 0 - 90 Grad voltage 230 V engine output 1200 W weight 65,0 kg - Includes quick-change chuck - for use with taps - for through holes and blind holes - Swivel motor unit for thread cutting - at any desired angle between 0° and 90° - Higher accuracy compared to manual thread cutting - Thread is guaranteed to be right-angled (90°) - High productivity - significant time savings compared to manual thread cutting - Quick-change chuck with integrated slip clutch - Includes swivel arm with large radius - for easy positioning of the tap on the workpiece - Highly economical due to low investment and maintenance costs - For thread cutting in steel, stainless steel, aluminum and non-ferrous metals Scope of delivery - Operation via touchscreen - Digital drilling depth display - Quick-change holder according to DIN - Quick-change chuck - Electric motor - 90° angle adjustment - Mounting flange Special accessories included: - BERNARDO base frame with 2 drawers * milled support surface 900 x 600 mm * including 3 T-slots (16 mm) Rodpfx Aexab Elsa Usp * large storage space and 2 drawers for storing tools * 4x swivel castors including parking brake - Mounts according to DIN 376: * M5-6 / M8 / M10 / M12 / M14 / M16 / M18 / M20 / M22-24 / M27 / M30 / M33 / M36

Condition: new, thread dia. bis M 36 turning speeds 0-100 U/min thread M5 - M36 working area 2050 Rmax. working range 500 Rmin. work height max. 900 mm table surface area 700 x 900 mm oil volume 100 l engine output 5,5 kW weight - pallet system ca. 500 kg Furnishing: - electro-hydraulic thread cutting machine - large working area (radius max. 2050 mm) * including table clamping disk * Swivel movement is smooth thanks to built-in gas pressure dampers - mobile machine base Rjdpfoxab Igox Aa Usp * Oil tank + hydraulic unit integrated in the base frame * hydraulic pressure gauge - continuous speed adjustment - vertical/horizontal thread cutting possible - Lateral sorting of the quick-change inserts possible - Connection cable with 16A plug Special accessories included / quick-change inserts: M05 / M06 / M08 / M10 / M12 / M14 / M16 / M18 / M20 / M 22 M27 / M30 / M33 / M36

Condition: new, thread dia. bis M 24 turning speeds U/min thread M5 - M24 working area 2050 Rmax. working range 500 Rmin. work height max. 900 mm table surface area 700 x 900 mm Rsdpexab Iasfx Aa Uop oil volume 100 l engine output 3,0 kW weight - pallet system ca. 300 kg Furnishing: - electro-hydraulic thread cutting machine - large working area (radius max. 2050 mm) * including table clamping disk * Swivel movement is smooth thanks to built-in gas pressure dampers - mobile machine base * Oil tank + hydraulic unit integrated in the base frame * hydraulic pressure gauge - continuous speed adjustment - vertical/horizontal thread cutting possible - Lateral sorting of the quick-change inserts possible - Connection cable with 16A plug Special accessories included / quick-change inserts: M05 / M06 / M08 / M10 / M12 / M14 / M16 / M18 / M20 / M22

Condition: new, thread dia. M5 - M24 turning speeds 70 - 200 U/min working area max. 1200 R angle adjustable from - to 0 - 90 Grad voltage 230 V engine output 1200 W weight 65,0 kg - with micro spray system for constant cooling & minimal Cooling lubricant consumption Rsdpfx Aexaaybea Uep - Includes blow-out device to remove chips, ensuring optimal visibility on the borehole - Includes quick-change chuck for using taps for Through and blind holes - Swivel motor unit for thread cutting at any desired angle between 0° and 90° - Higher accuracy compared to manual thread cutting, thread is guaranteed right angle (90°) - high productivity, significant time savings compared to manual Threading - Quick-change chuck with integrated slip clutch prevents breaking of the tap - Includes large radius swivel arm for easy positioning tap on the workpiece - For thread cutting in steel, stainless steel, aluminum and non-ferrous metals scope of delivery - Operation via touchscreen - Digital drilling depth display - Micro spray system - Blow-out device - Quick change mount - Quick-change chuck according to DIN - Electric motor - 90° angle adjustment - Mounting flange Special accessories included: - BERNARDO base frame 900 x 600 mm (Art. No.: Mounts: DIN 376: M5-6 / M8 / M10 / M12 / M14 / M16 / M18 / M20 / M22-24

Condition: excellent (used), Year of construction: 2017, functionality: fully functional, ATH-D automatic glass loader double side jumbo Rodpfjynl Uhjx Aa Uep 3300 x 6000 mm