Used Crossfield Scanner for sale (348)

Condition: excellent (used), Here we offer you a Bielomatik laser welding system. Bielomatik laser welding system Machine description: The laser unit with integrated cooling for the laser is located in the lower left part of the machine frame. The tools are mounted on a 2-station rotary table that rotates 180 degrees with each cycle. In the middle part of the machine frame, there is the working area with the welding station, the tool (on the rotary table), and the clamping device for the product. The control cabinet is installed at the rear. The welding station is protected against the loading/unloading area with a laser-safe enclosure. The welding laser (the laser power supply) is switched off when a maintenance door is opened. The loading and unloading of the welding parts is done manually. The welding process runs automatically. Laser type: YLR-300-AC-Y11/IPG The cell was used for laser welding of various plastic parts (front frames). For components with dimensions of approximately 460 x 280 mm. Basic data Machine equipment: 1 complete machine frame with enclosure, substructure, and safety devices, painted Adjustable machine feet, designed for transport with a forklift. 3 manual maintenance doors in the laser-safe processing area, each secured with a safety door switch with interlock. 4 manual maintenance doors below the machine table. The control cabinet is permanently mounted on the rear of the machine. Laser system manufactured by IPG. 1 fiber laser, 300W cw, at the fiber optic end, 1070nm, completely air-cooled. 1 power supply for the laser unit, target beam laser, and fiber optic cable. 1 Vario-Scan for 3D welding contour. 1 scanner - 20 aperture. Optics, F-Theta lens, focal length determines the processing field and processing distance. 2x base tool, tool coding with transponder. Clamping/tensioning system for holding a mask with absolute encoder. with pneumatic clamping system for controlled pressing of each welding part. Pneumatic air shower for protection of the lens housing. Microbox PC427B incl. RTX (Siemens). Pre-installed software, Siemens S7 PLC. Profibus, Profinet, Ethernet, RS232 interface. Touch panel 15" for operation and input of data/parameters. Machine lighting. Connection flange for external extraction system. Machine data: Dimensions: Machine W x D x H: approx. 2330 x 2350 x 2500mm Control cabinet: Permanently screwed to the machine frame. Area required W x D: 5400 x 5400mm Technical data: Power supply: Number of phases/rated voltage 3x400V 50Hz Connected load 5KVA Fuse rating: 16A Exhaust: Nominal size ∅160 Airflow rate 500-1000 m³/h Weight approx. 2000 kg Type: K3633/023 Iodpfjzgaazex Ad Njba Condition: used (Changes and errors in the technical data are reserved!) We are happy to answer any further questions you may have by telephone.

Condition: used, Year of construction: 2023, SUNHUB – Compact Dispenser Year of manufacture: 10/2023 Condition: good condition, as is, operational Equipment: HEAD SunHub -20-NH-UV-20-N.00 DOSING VALVES BP2 5-N-50 – INK PUMP 2.5 kg SCALE ICS06s-6M/f METTLER TOLEDO LABEL PRINTER + CODEBAR SCANNER External Pump 25 kg CONNECTION X-RITE Iedpfezf H Rdox Ad Nsba

Year of construction: 2026, condition: new, working width 1000 mm workpiece width - max. 0,5 - 50 mm sandingbelt width -- mm weight of the machine ca. 2,5 t With the SBM-L 1000 G1S2, which works in the dry process, in alternating operation Steel, stainless steel and aluminum can be machined. She deburrs and rounds the edges on the outer and inner contours of punched, laser, fine plasma or water jet cut workpieces with a thickness of up to 50 mm on both sides in just one operation. * Two sanding units, 1 each on the top and bottom, remove spatter and slight burrs on outside and inside edges of sheet metal. * A total of four sanding belts, 2 each on the top and bottom Underside, process the sheets on both sides at the same time. here All edges are softened or rounded, depending on the tool settings. * Machining on both sides saves time-consuming turning of the workpieces and edit twice. * All pairs of aggregates can be switched on/off separately depending on the application as well as to be set. * Including Siemens S7 control: - Easy and comfortable operation through intuitive user interface - High operating security through 3 password-protected user levels Ijdpfxjuia Dqe Ad Njba - Integrated program memory - USB / RJ 45 interface for data exchange or connection of external Components (e.g. barcode scanner) - Direct entry of material thickness via touch panel - All axes automatically adjust to preselected material thickness - Standby position for deactivated aggregates - Service-friendly (e.g. plain text error messages) consisting of: - Grinding machine SBM-L 1000 G1S2 (kit) - 4x sanding belts SBM 1000 with bar P60 SiC - Sanding belt SBM-L 1000 L=3125 B=70 P80 Cubitron 2 784F - SBM-L tool wear compensation Siemens S7 - DDE 3002 dry suction - Standard piping DDE 3002 / WDE 3002 for SMD 123, SMD 133 Further detailed technical data on request. The machine is in stock Niederlangen available immediately.

Condition: new, Year of construction: 2026, functionality: fully functional, The StoNail 7000 is a fully automated portal nailing machine for the flexible production of pallets and crates, even with large workpiece dimensions. With up to three individually adjustable nailing head pairs, two work areas, and a generous Y-axis travel of 1,250 mm, it is designed for maximum efficiency and high flexibility. A 12-inch touch display, automatic height adjustment, and numerous expansion options support user-friendly operation. Offline programming allows new programs to be created and simulated outside the machine, reducing setup times and preventing downtime. The integrated automatic path optimization further increases the cycle output and ensures resource-efficient operation. Applications: Standard stringer and block pallets Special pallets & custom solutions Double-deck pallets & mixed pallets Transport frames & packaging elements Crate walls & wooden packaging Nailing bridge with rotary table: Robust frame construction with a tilt angle of 65° for ergonomic operation Machine length: approx. 7000 mm Rotary table with 2 work areas: Work area per side (L x H): 3000 x 1700 mm Cladding of the rotary table with plywood panels for custom templates Option: Clamping brackets for use with custom templates Option: Modular pallet clamping system for inserting loose boards and blocks Frequency-controlled nailing bridge: Up to three independently controlled nailing head pairs for complex nailing patterns Accommodation of up to 6 nailing heads Coverage of the entire work area with the nailing heads Collision monitoring: The movement of the feed cylinder is constantly monitored Nailing heads: Industrial nailing heads or hand-held devices Nail length max.: 130 mm Equipment of the nailing heads with Maxi-Coil magazines for up to 1000 nails Nailing shoes for limiting the insertion depth Option: Stapling devices, drilling heads Ibsdporallrsfx Ad Nea Robot: Type: Kuka KR210 R3100-2 (Alternatively: similar manufacturer or refurbished robot possible) Gripper with clamping jaws for pallet removal and stacking Product weight max.: 80 kg Stacking height max.: 2800 mm Normal and interleaved stacking Option: Retrofitting the robot at a later date Buffer conveyor (Optional): For buffering several pallet stacks Fully enclosed by a robust plastic modular belt Programming: Simple, intuitive programming on the 12-inch touch panel directly on the machine. With the entered parameters, the pallets or crate parts are completely recorded or visualized. Programming of the removal and stacking process via robot is also done directly on the touch panel – no robot knowledge required by the customer. Siemens PLC control with control panel: Touch panel for operating the machine Pallet programming directly on the control panel Storage of the created pallet programs Pallet counter Nail counter: The machine stops as soon as the nails are used up Internet connection for remote maintenance Operating language available in German and English Option: Board width measurement for decreasing board widths Safety equipment: Safety fence around the entire system including access monitoring Emergency stop button on the outside of the machine and on the control panel Safety laser scanner to protect the rotary table Safety light curtain for pallet removal

Condition: new, Year of construction: 2026, The StoNail 7000 is a fully automated portal nailing machine for the flexible production of pallets and crates, even with large workpiece dimensions. With up to three individually adjustable nailing head pairs, two work areas, and a generous Y-axis travel of 1,250 mm, it is designed for maximum efficiency and high flexibility. A 12-inch touch display, automatic height adjustment, and numerous expansion options support comfortable operation. Offline programming allows new programs to be created and simulated outside the machine, reducing setup times and preventing downtime. The integrated automatic path optimization further increases the cycle output and ensures resource-efficient operation. Applications: Standard stringer and block pallets Special pallets & customized solutions Double-deck pallets & mixed pallets Transport frames & packaging elements Crate walls & wooden packaging Robust frame construction with a tilt angle of 65° for ergonomic operation Machine length: approx. 8500 mm Work area (L x H): 1 pallet: max. 5500 x 1700 mm or 2 pallets: max. 2000 x 1700 mm Option: Extension of the machine frame by 2000 mm or 4000 mm, or according to customer requirements Option: Widening of the machine frame by 300 mm Nailing table: Cladding of the nailing table with laminated wood panels for custom templates Option: Clamping brackets when using custom templates Option: Modular pallet clamping system for inserting loose wood and blocks Frequency-controlled nailing bridge: Up to three independently controlled nailing head pairs for complex nailing patterns Accommodation of up to 6 nailing units Covering of the entire work area with the nailing units Collision monitoring: The movement of the delivery cylinder is constantly monitored Start button located directly on the nailing bridge Nailing units: Industrial nailing heads or handheld devices Nail length max.: 130 mm Equipment of the nailing units with Maxi-Coil magazines for up to 1000 nails Nailing shoes for limiting the penetration depth Option: Stapling units, drilling heads Programming: Simple, intuitive programming on the 12-inch touch panel directly on the machine. The entered parameters are used to completely record or visualize the pallets or crate components. Isdorallnopfx Ad Njba Siemens PLC control with control panel: Touch panel for operating the machine Pallet programming directly on the control panel Storage of the created pallet programs Pallet counter Nail counter: The machine stops as soon as the nails are used up Internet connection for remote maintenance Operating language available in German and English Option: Board width measurement for varying board widths Safety equipment: Emergency stop button on the machine and on the control panel Safety light curtain around the nailing beam with Keyence laser scanner

Condition: good (used), Horizon HCB-2 semi-automatic machine for producing hardcover books The machine is in very good condition, little used. The task of the machine is to produce a finished cover, assemble the book block into the cover and joint forming in the finished book. The machine is very easy to set up, operate and service. The machine is equipped with the following elements: touch control monitor table for mounting the cover with a laser pointer module for wrapping veneer edges ironing rollers barcode scanner Iedpfx Aoztpb Ied Nsba Technical data: – cover size: max. 680.6×340.8mm; min. 322.4 x 169.7 mm – spine thickness: min. 3mm; max. 25mm – cover weight range: 105 – 160 g/m2 – speed: max. 150 cycles/hour – dimensions: 1,800 x 1,050 x 1,536mm – weight: 456kg Power supply: 230 V / 50 Hz instruction manual included and a large set of materials. Ask About The Product

Condition: excellent (used), 3D systems Ibedpfx Ajzd Tt Aod Nea Here we offer you a 3D printer. Solid-State Nd:YVO4 with triple frequency Wavelength: 354.7nm Nominal power at the laser head: 1450 mW (1000 mW at the resin surface under standard conditions) Zaphyr™ coating system: Process: Replaceable coater Adjustment: Self-leveling and self-correcting Layer thickness: Minimum 0.05mm, maximum 0.15mm ProScan™ scanner Edge detection (diameter at 1/e2): Nominally 0.13mm in standard mode Large line detection: Nominally 0.76mm Maximum drawing speed Edge detection: 3.5 m/s Large line detection: 25 m/s Build volume: RDM 750F: 650mm x 750mm x 550mm; 414l Maximum part weight: 75kg Power supply: 200-240VAC (alternating current), 50/60Hz single-phase, 30A Environmental conditions Temperature range: 20-26°C Max. permissible fluctuation: 1°C per hour Relative humidity: 20-50%, non-condensing Space requirements: Size (W x D x H), unpacked: 1260mm x 2200mm x 2280mm Weight packed (without RDM): 1590kg Type: iPro 8000 Condition: used Scope of delivery: (See pictures) (Changes and errors in the technical data and specifications are subject to change!) We will gladly answer any further questions you may have by phone.

Condition: good (used), Indumat THO 310 Automated Guided Vehicle (AGV) A robust, industrial automated guided vehicle (AGV) from the proven system portfolio of INDUMAT and E&K Automation. The vehicle combines Indumat’s extremely solid and durable mechanical engineering with the flexible control technology of the TELETRAK MULTI series. The unit is ideally suited as a source of spare parts, for retrofit projects, for automating internal facility processes, or for expanding existing systems. Technical Data (according to nameplate): Manufacturer (Mechanical): INDUMAT GmbH & Co. KG (Reutlingen) Control System / Brand: E&K Automation TELETRAK MULTI Model / Type: THO 310 Unit No.: 9930 92 26844 Year of Manufacture: 03/1993 Load Capacity: 1000 kg Dead Weight (without battery): 2720 kg Nominal Battery Voltage: 48 V Equipment & Components: The vehicles were subsequently upgraded with modern touch-display controls and are in good, clean condition. These vehicles are constructed using high-value, sought-after industrial components of OEM quality. Professional Safety Laser Scanners: High-end sensors for personnel and obstacle detection. Load Handling Device: Integrated, powered roller conveyor featuring three flanged guide rollers for the automatic, centered pickup and transfer of specific load carriers (e.g., pallets or special racks). Control & HMI: Side-mounted control panel featuring a display, key switch, function buttons, indicator lights, and a connection port for a wired handheld control unit. Safety Features: Easily accessible emergency stop switch; Cutouts in the bumper area for optical pedestrian protection scanners (e.g., SICK laser scanners) or mechanical safety edges. Control cabinet: Spacious electronics compartment for the central control system, located in the upper housing section and accessible via lockable double doors. "Everything from a single source: We would be happy to offer you suitable bank financing for your project." komplett-konzept.leasingo.de You can find more items—both new and used—in our shop! Iodezkqdxjpfx Ad Njba International shipping costs available upon request!

Condition: used, Year of construction: 1996, Transnorm roller conveyor TS 2800 sorter switch 1980-1250-1150 RA1999 Make: Transnorm Roll width (RB): 1150 mm Nominal/outer width (NB): 1250 mm Length: 1980 mm Diameter rollers: 50 mm distance between rollers: 76 mm Roller conveyor motor: 2x SEW drive motor Angle of the rollers is adjusted pneumatically (see pictures) conveying speed: approx.1,73m/s maximum recommended box/package width: 400 mm Theoretical sorting speed at 600 mm crate length: ca. 4250/h Included: Side guide included on one side Control valve Optionally available: Supports Side guides on both sides Conversion to box width up to 500 mm Barcode scanner Control system (stand-alone unit) System optimization (e.g. replace valves, dual solenoid valve, forward conveyors, frequency converter) for higher flow rate 6000++ and more For individual, expert advice, simply get in touch with us. Simply contact us by phone or email. We will be happy to help you plan and implement your projects. We look forward to hearing from you. Ijdpfek Abryox Ad Neba With kind regards Your team at Dr. Sonntag GmbH & Co. KG Your specialist and contact for intralogistics

Condition: new, Bore diameter variabel mm Number of heads horizontal 1 St. Number of heads vertical 0 St. Götzinger drill, dowel gluing and insertion machine BLE With the BLE, the workpieces are glued and dowelled on the front. Optional the BLE can be upgraded with a drilling unit, counter milling unit and longitudinal stop will. A 10" touch panel allows easy operation for manual or online operation. Base frame: in a compact design, covered with sheet metal Table support approx. 800 x 200 mm position 1 ----- 1 glue station full jet valve Glue quantity precisely adjustable Glue gun for counter hole gluing position 2 ----- 1 stainless steel glue pump, high-pressure pump and glue hose item 3 ----- 1 press-in station with dowel separation and press-in cylinder item 4 ----- 1 oscillating conveyor for dowels d 8 x 60 mm with feed hose into the injection unit item 5 ----- 1 processing unit with cross table, linear guide and 3NC axis motors X = 200 mm processing width Y = 120 mm processing height Z = 50 mm offset item 6 ----- 1 positioning controller Touch panel 10" color 500 drilling patterns can be created and saved, which can be easily accessed when needed (1 drilling pattern can have up to 16 dowel positions) Software prepared for ONLINE connection With online control, the data for the control must be provided by the software be prepared. Our machine can then read and process this data. ----- Total price in this version Pos. 1 to Pos. 6: on request! Options with additional prices: ----- item 7 ----- 1 horizontal drilling unit, 1,000 W drilling motor Speed ??4,000 - 8,000 rpm, collet holder Pneumatic drill feed Surcharge: EUR 4,565.00 Additional accessories such as a larger touch screen, additional dowel station for additional dowel sizes or scanner for Program selection on request! Ijdpfx Adeu Uu Uzs Nsba Prices net plus statutory VAT, without packaging/shipping and without Installation. ----- (technical data according to the manufacturer - without guarantee!)

Condition: good (used), WAGNER UGH-Z1-Q 1000 Automated Guided Vehicle (AGV) System For sale: Automated Guided Vehicles (AGVs) from the premium manufacturer ek robotics (formerly ek automation), built on robust WAGNER chassis. These vehicles come directly from a Mercedes-Benz plant, where they were used for precise, automated material transport. Due to their use in the automotive industry, the units have undergone rigorous maintenance in accordance with the highest quality and safety standards. The vehicles were subsequently upgraded with modern touch-display controls and are in good, clean condition. These vehicles are constructed using high-value, sought-after industrial components of OEM quality. Professional safety laser scanners: High-end sensors for personnel and obstacle detection. An ideal opportunity for logistics companies looking for high-end spare parts for existing systems, for parts recyclers, or for ambitious automation projects. Technical Data Chassis Manufacturer: WAGNER Fördertechnik GmbH & Co KG Model / Type: WAGNER UGH-Z1-Q 1000 Rated Load Capacity: 1,000 kg Total Weight (incl. battery): 2,980 kg System Voltage: 48 V "A complete solution: We would be happy to offer you suitable bank financing for your project." Iodpfx Adszklkte Njba komplett-konzept.leasingo.de Find more items—both new and used—in our shop! International shipping costs available upon request!

Condition: used, Year of construction: 2015, Processing Specifications: Maximum processing width: 610 mm Minimum processing width: 210 mm Maximum draw length without interruption: 610 mm or 410 mm, depending on configuration Minimum draw length without interruption: 50 mm Maximum draw length with interruption: 1,220 mm or 820 mm, depending on configuration Minimum draw length with interruption: 100 mm Maximum cycle rate: 210 cycles/min Maximum line speed: 50 m/min Unwinder: Maximum reel diameter: Ø1,000 mm Maximum reel weight: 700 kg Web width with 48-inch unwinder: 410–1,220 mm Web width with 60-inch unwinder: 410–1,520 mm Processable Materials: Polyester laminates: from 40 μm BOPP laminates: from 40 μm CPP laminates: from 40 μm Nylon-based co-extruded films: from 50 μm EVOH-based co-extruded films: from 50 μm LD/LLD-based co-extruded films: from 50 μm BOPP film: from 30 μm Aluminum foil structures Coated paper Tyvek Maximum sealable film thickness: 150 μm Pouch Types: • TSP pouches • Stand-up pouches • Supported-film pouches Electrical Data: Power supply: AC, 3 Phase Available voltage: 20 / 240 / 380 / 415 / 480 V ±6% Frequency: 50/60 Hz Machine-specific supply: 380 V, 50 Hz, 3 Phase Machine electrical load: 35 kVA Pneumatic Requirements: Air consumption: 1,000 L/min at NTP Installed configuration air requirement: 3,000 L/min Minimum operating pressure: 6 kg/cm² Air supply must be free from moisture and dust Cooling Water: Water consumption: 20 L/min Required water temperature: 15–17 °C Standard Machine Features: • Servo-driven film indexing Ijdszqt Dnepfx Ad Njba • Microprocessor-based control • Operator console for process parameter settings • Servo tension dancer assemblies with feedback control • Tail-feed-assisted film draw mechanism • Servo-driven reciprocating sealing system • Servo-actuated sealing bars • Progressive sealing and rapid seal-area cooling • Three-stage bottom sealing followed by cooling • Adjustable sliding sealing stations • PID temperature controllers with auto-tuning • Photo-registration mark scanner • Guillotine-type shearing station with servo fine adjustment • Trimming station with trim removal • Recipe memory for frequently used jobs • Adjustable sealing temperature, pressure and dwell time • Automatic stacking system

Condition: excellent (used), Here, we offer you a 3DMICROMAC laser marking system. microCUT Enclosure Laser source IPG Raylase 3-axis scanning system Power measurement head 1 Power measurement head 2 Camera system for positioning Camera system for quality inspection Cooler Extraction system Control cabinet with IPCs Coolant distributor Machine dimensions: Machine weight: 2 tons Width 922 mm, Depth 4653 mm, Height 2925 mm Components: Extraction system: Height 2869 mm, Width 760 mm, Depth 1577 mm Cooler: Height 1697 mm, Width 1440 mm, Depth 860 mm Weight (without filling) 500 kg Laser rack: Height 1786 mm, Width 856 mm, Depth 806 mm Weight 500 kg Control cabinet: Height 2001 mm, Width 1616.05 mm, Depth 605 mm Machine connections: Electrical: Mains voltage 3*400 VAC/N/PE Mains current consumption 74A Frequency 50/60 Hz Power consumption 51.3 kW Control voltage 24/5 VDC Main fuse NH 100A gG Module: Laser source: Mains voltage 400 VAC Frequency 50/60 Hz, Power 16.7 kW, Current consumption 59A Cooler: Mains voltage 400V, Frequency 50/60Hz, Current consumption 40A Machine: Consumable media Operating pressure 6-10 bar Temperature 10-50 °C Quality ISO 8573-1 Ibsdpfx Aszdqp Isd Nea Solid particles: Class 1 Oil: Class 1 Water: Class 4 Residual oil content < 10µg/m³ Water content < 6 g/m³ Pressure dew point 3 °C Consumption < 120 l/min Cooling water cooling unit module: Cooling water outlet temperature 21°C Cooling water return temperature 26°C Set point tolerance 1K Cooling water flow rate 69 l/min Free pump pressure 1.5 bar DI water cooling unit Cooling water outlet temperature 26°C Cooling water return temperature 31°C Set point tolerance 1K Cooling water flow rate 10 l/min Free pump pressure 1.5 bar Laser source manufacturer IPG, Type: YLS-5000, Mode: Continuous wave, Quasi-continuous wave Wavelength 1070nm Power 5kW, Frequency 5 kHz Scanner manufacturer Raylase AG Type: Axialscan-30-Y Field size 1000x1000 mm Spot diameter 87 1/e²(µm) Resolution < 31 µm Working distance 1198 mm Cooling unit: Manufacturer Riedel Type: PC 250.01-NZ-DI-S Refrigerant R407C 50 Hz Net cooling capacity 38 kW 60 Hz Net cooling capacity 40.3 kW Camera system: Manufacturer e2V, Type: AVIIVA TM UM2 GE Quality cameras: Manufacturer e2v, Type: DiViiNA LM1 CL Extraction system: Manufacturer Donaldson Filtration, Type: DOWNFLO Oval 3-3 Max. Fan speed 3000 rpm Operating pressure: 4.2 bar Pulse duration 100ms Volume of the pressure vessel 92 l Type: Laser marking system microCUT Condition: used Scope of delivery: (See pictures) (Changes and errors in the technical data are subject to change!) We will be happy to answer any further questions you may have by telephone.

Condition: new, Year of construction: 2026, functionality: fully functional, The StoNail 5000 is a powerful portal nailing machine for the automated production of pallets and crates. With up to eight nailing heads, two work areas, and a 750 mm stroke on the Y-axis, it offers a high production capacity for a wide variety of nailing patterns. The system features a 12-inch touch display, height adjustment, and individual control of the nailing heads. Downtimes are significantly reduced by the optional offline programming, as programs can be created and simulated outside of production. The automatic path optimization also ensures short travel distances and increases the cycle output while reducing resource consumption. General advantages: Modularity: Adjustable machine length and configuration to meet specific production requirements. Flexibility: Suitable for small pallets (two stations simultaneously) and large pallets (full work area). Automation: The machine optimizes the work process through automatic calculation of the most efficient and fastest nailing path. Nailing table with nailing bridge: Construction: Robust frame with a 65° inclination angle for ergonomic operation. Machine length: approx. 8500 mm (extendable/shortenable by 2000 mm or as per customer request). Work area: 1 pallet: max. 6000 x 1700 mm 2 pallets: max. 2500 x 1700 mm per pallet Stop system: Parallel adjustable double C-rails Manually adjustable stops for bottom rails, cross rails, and top boards Rivet plates can be used at all positions Pre-fabrication of the skids Ibodpfx Adjztanxs Nsa Optional special equipment with laminated veneer lumber for custom templates Optional aluminum clamping system Nailing bridge: Frequency-controlled for positioning the nailing heads Equipped with 6 nailing head units including feed cylinder, nailing head holder, release and nailing head shoes for limiting the insertion depth Manual nailing head quick adjustment for different pallet formats Safety features such as collision monitoring (the movement of the feed cylinder is constantly monitored) Start button directly on the nailing bridge Nailing heads: Type: depending on customer requirements (Bea, Bostitch, Max, Fasco,…) Nail capacity: Up to 90 mm nail length (longer nails available upon request) Option: Maxi-Coil magazines for up to 1000 nails Programming and control: Easy operation: Intuitive programming incl. visualization of the product to be nailed (pallets and crates) Control: Siemens PLC with touch panel Functions: Pallet programming directly on the control panel Pallet and nail counters, the machine stops as soon as the nails are used up Storage of created pallet programs Remote maintenance via internet connection Multilingual operation (German, English, Czech, Polish) Safety equipment: Emergency stop button on the machine and on the control panel Emergency stop at the start on the nailing bridge Option: non-contact safety laser scanner on the nailing bridge

Condition: new, functionality: fully functional, Year of construction: 2026, load capacity: 1,200 kg, lifting height: 115 mm, fuel type: electric, fork length: 1,150 mm, empty load weight: 160 kg, total length: 1,520 mm, drive type: Elektro, construction width: 560 mm, Low-lift truck Load center: 600 Condition: New Technical condition: New Front tire size: SINGLE LOAD TIRE Front tire condition: New Rear tire condition: New Battery voltage: 48V Battery capacity: 9Ah Battery manufacturer: VForce Battery type: Lithium-ion Battery year of manufacture: 2025 Battery condition: New Description: IMMEDIATELY AVAILABLE Optional extras: Load protection grid, lithium-ion batteries in 48 V / 9.8 Ah, 14.7 Ah, 19.6 Ah, or 24.5 Ah, external charger, access control (keypad or card reader), scanner holder, storage bag. Ibedpozrckaofx Ad Nea

Condition: like new (used), Year of construction: 2013, functionality: fully functional, machine/vehicle number: PB33313, input voltage: 230 V, measuring range X-axis: 50 mm, measuring range Z-axis: 300 mm, total width: 650 mm, total length: 500 mm, total height: 1,100 mm, overall weight: 110 kg, operating temperature: 20 °C, input current: 2 A, repeat accuracy: 0 mm, input frequency: 50 Hz, workpiece height (max.): 270 mm, workpiece width (max.): 40 mm, Equipment: documentation/manual, For sale: Highly precise optical measuring machine, VICI VISION scanner - Type: MTL-300 EVO - Year: 2013 - Serial No.: PB 33313 - Weight: 110 kg I am selling a new, complete and highly accurate optical measuring scanner for fast and precise measurement of complex shapes: diameters, lengths, radii, grooves, angles, offsets, and various surfaces on the same part. 50 or more measurements per minute. The machine includes additional equipment: a stable table, computer, and software for generating measurement reports and certificates. Ibsdpfx Aoy Rzdlsd Nja Regularly serviced by the manufacturer. It is connected to the mains and ready for immediate operation.

Condition: like new (used), Year of construction: 2014, functionality: fully functional, machine/vehicle number: PH 54114, input voltage: 230 V, measuring range X-axis: 300 mm, measuring range Y-axis: 30 mm, measuring range Z-axis: 60 mm, total width: 1,014 mm, total length: 505 mm, total height: 785 mm, overall weight: 100 kg, temperature: 20 °C, repeat accuracy: 0.001 mm, workpiece length (max.): 300 mm, workpiece height (max.): 30 mm, workpiece width (max.): 60 mm, Equipment: documentation/manual, For sale: Highly precise optical measuring machine, VICI VISION scanner - Model: MTP 120 – 230 SCEPM Iedpoy Rzizofx Ad Njba - Year: 2014 - Serial No.: PH 54114 Offered for sale, as new, is a complete and highly precise optical measuring scanner for extremely fast and accurate measurement of complex shapes: radii, angles, irregular holes, gears, complex curves, ellipses, and more. The device offers outstanding accuracy and is suitable for rapid certification production meeting the most demanding requirements (e.g. used for measuring gears in Swiss watches, etc.). The measuring system has been maintained and serviced by the manufacturer VICIVISION. Essential for serial production. It is connected to the power supply and ready to operate.

Condition: refurbished (used), functionality: fully functional, warranty duration: 12 months, input voltage: 230 V, measuring range X-axis: 250 mm, measuring range Z-axis: 320 mm, overall weight: 95 kg, - Leasing options available!!! - Modular expandable basic contour measuring system, Z-axis measurement direction downwards Optional functions expandable via software update: Iedpfxezict Aj Ad Noba - Up/Down measurement direction switch - Roughness measurement - QR code scanner (for probe arms and reference parts) - Data export to QS-Stat (dfq data) - Dominant waviness - Free commissioning and training within a 150 km radius - - Free software update for contour software Scope of delivery: - Complete mechanics with Y-axis adjustment table (17 mm travel) - Integrated controller - PC W11/64-bit; 24" TFT flat screen - ConturoMatic software; operating manual - Dust cover, robust design, water-repellent Technical data: Measuring range X 250 mm Measuring range Z 320 mm Resolution 1 nm Measuring systems: optical incremental System accuracy +/- (0.9 µm + L/100) µm * [L = mm] Probe force control Measuring speed 0.1 - 3.0 mm/s, automatically optimized Positioning speed up to 25 mm/s Table load capacity 35 kg Precision guide on hard stone base Weight 95 kg

Condition: ready for operation (used), Year of construction: 2020, travel distance X-axis: 25,000 mm, CMM machine manufactured in 2020. This KEYENCE WM c3000 includes a measuring range of up to 25 m and operates within a temperature range of 0 to 40°C. The delivery scope features a camera tripod, laser scanner, handheld tactile probe unit, and various measuring tips. If you are looking to get high-quality measurement capabilities, consider the KEYENCE WM c3000 machine we have for sale. Contact us for further details. - Input Voltage: 24 V DC- Input Current: 1.7 A- Measuring Range: Up to 25 m- Operating Temperature Range: 0 to 40°C- Interface Ports: USB, Power Input- Scope of Delivery / Included Components:* Camera tripod with black carrying bag* Laser scanner (WM-P6200 compatible series) and handheld tactile probe unit in a heavy-duty rolling hard-shell transport case* Component accessory box with various measuring tips/styli* Position-tracking magnets for reference points and calibration* Power supply units (AC adapters) and connection cables* Printed technical documentation / instruction manuals- X-axis travel: 25,000 mm- Y-axis travel: 12,500 mm- Z-axis travel: 12,500 mm(based on the specified measurement volume of 25 m × 12.5 m × 12.5 m) Iedpfozggw Tjx Ad Nsba

Year of construction: 2010, condition: ready for operation (used), functionality: fully functional, working length: 7,600 mm, machine/vehicle number: 1400040505, number of axes: 4, TECHNICAL DETAILS Max. machining length with end face machining: 7,600 mm Max. machining length without end face machining: 7,720 mm EQUIPMENT 12 pneumatic collet chucks 2 work areas 4-axis profile machining center; stepless machining between -90° and +90° with each available tool Automatic clamping position adjustment with absolute measuring system Two separate machining zones for tandem operation 4-axis control 18.5" color monitor, USB ports, and network connection Windows operating system EluCam software Automatic profile length measurement (on both sides) Barcode scanner The traversing tool magazine ensures short tool change times and thus optimal machining cycles; the magazine can be equipped with eight tools. Ibodpfx Aszhuyfjd Nja 8x tool holders with collet chucks

Condition: new, Year of construction: 2022, Demonstration machine Isdpjwt E Tvsfx Ad Noba Year of manufacture: 2022 Equipment and technical data: Base machine 7402 with Pin-Jet dowel insertion function Handheld control device 2D barcode scanner Uninterruptible power supply (UPS) Quattro-HSK package incl. 4-position tool changer XL drilling head Double drill spindle in Y-axis Automatic central lubrication Availability: short notice Location: Flörsheim

Year of construction: 2025, condition: new, Demo machine Year of manufacture: 2025 Ibodpfx Asxc Rmqjd Nja Travel range: 2500x1300x200mm Machine frame in 19mm Forescolour, consisting of milling table (X-axis), gantry (Y-axis), Z-axis unit in compact board, and base frame with adjustable machine feet. Milling bed as sacrificial board in 19mm MDF. Table openings longitudinally and transversely pre-configured. Mechanical set consisting of profile rails including profile rail carriages, ball screw and precision rack gears. All components assembled, pre-lubricated including test run, immediately ready for operation. Control set consisting of control cables, energy chains, planetary gears, stepper motors, high-performance drivers, power supply and toroidal transformer, all preinstalled in the control cabinet, as well as sensors for each axis. Control relay for automatic actuation of the existing extraction system. Brush seals for dust protection and protective equipment compliant with CE regulations: includes moving extraction unit and one-sided mounted laser scanner for work area monitoring, with 275° and 5.5m field range. (Machine positioned in a room corner) Manual control panel equipped with all necessary machine functions, including emergency stop and dead man’s switch. Tool length sensor for determining tool length and active offset of the reference point. High-frequency spindle with 2.2 kW, incl. clamping nut, frequency inverter, power filter, breaking resistor, and collet set. Built-in monitor, incl. mini PC with Windows 11, control software Beamicon2, mouse and keyboard, pre-installed in an ergonomic console. CAD license Rhino 8.0 and CAM license Estlcam V12, as well as all necessary documentation, will be sent by email prior to delivery. Includes milling bed designed as a vacuum table, consisting of four individually controllable segments. Cross table made of PE with top layer in MDF. Becker vacuum pump with a capacity of 100m³/h, oil-lubricated. A 16 Amp, 400 V AC plug is required for the vacuum pump electrical connection. The customer must provide HDF 3mm raw on both sides for the whole vacuum table (2500x1300mm) as a sacrificial board. (Recommended application: machining of coated wood-based panels) Includes 10-piece tool set consisting of: 3 pcs. 5 mm Z2 (HF52REVHM) 6 pcs. 4 mm Z1 (HF41REVHM) 1 pc. 5mm Z3 (HF53SRECAR) (Tool selection can be adapted as needed) Includes maintenance package in systainer: - 150 ml grease gun - 400 g cartridge high-performance grease - 500 ml can of silicone spray grease - Grease nipple incl. hose and 30mm face mill with indexable inserts Availability: short notice Location: Flörsheim

Condition: good (used), Horizon BQ-270C Perfect Binder Machine in very good condition. Ready to use. Very low mileage. Manufacturer’s description: Professional binder for perfect paperback binding. This fully automatic binder features an exceptionally sturdy design and is equipped with a hot glue gun, making it effective even for small and very small quantities of book covers or pages. The Horizon BQ-270C is a single-jaw binder with automatic cover feeding, which, operated by a single person, delivers impeccably bound books of consistently high quality. Equipped with a core thickness scanner, it allows for on-demand binding. Ibjdpfx Adozrfcls Nsa Binds books with a thickness of 0.5 to 50 mm and a spine length of 135 to 320 mm, with a maximum production rate of up to 500 books per hour. Factory-installed cutter with additional scoring knives. Maximum milling depth up to 3 mm. Automatic cover feeding via a suction drum with a secure, consistent alignment with the bound sheets. A factory-installed system creates 4-fold creases on the cover, which automatically adjusts for precise alignment.

Year of construction: 2018, condition: excellent (used), For machining aluminium and steel profiles Fully functional, in very good condition Machining length: 7200mm 3-axis control with 15" screen Tool changer: 8 positions / turret 8 pneumatic horizontal material clamps Autonomous clamp positioning Two separate work zones, suitable for pendulum operation 2 pneumatic material stops 8 tool positions / BT30 turret Barcode scanner Handheld control unit Safety light barrier at the front and side safety fence Minimal quantity lubrication Central lubrication Thread cutting without compensating chuck Simple programming at the control panel Ibedpfx Adszmrhke Nsa High-speed spindle up to 18,000 rpm Including 3 angle heads X-axis [mm]: up to 7,200 / 7,200 Y-axis [mm]: up to 485 / 310 Z-axis [mm]: up to 340 / 260 Rapid traverse speed X/Y/Z axis [m/min]: 60/60/60 Max. milling cutter diameter: 25mm Max. saw blade diameter: 180mm Max. tool length: 200mm (tool + holder) Max. spindle speed: 6,000 rpm Spindle power: 6 kW Weight: approx. 5.5 t Total operating hours: 30,844 h Total spindle hours: 11,583 h

Condition: excellent (used), functionality: fully functional, Equipment: documentation/manual, type plate available, FARO Quantum M ScanArm 2.5 m with FAROBlu HD Laser Line Probe and MetrologyWorks Kodiak HDP-KCF heavy-duty tripod Ibjdpfxezt Dpye Ad Nea Complete portable 3D metrology system for tactile coordinate measurement and 3D scanning. System configuration: FARO Quantum M ScanArm Measuring range: 2.5 m 7-axis articulated measuring arm FARO LLP HD Laser Line Probe, Rev. 3.2 Tactile measurement probes and accessories MetrologyWorks Kodiak HDP-KCF heavy-duty carbon-fiber/aluminium tripod Original FARO transport case Batteries, power supply and cables Mounting accessories Existing calibration documentation The system is suitable for dimensional inspection, CAD-to-part comparison, First Article Inspection (FAI), production control, tooling and fixture inspection, and reverse engineering. The measuring arm and scanner are fully functional and can be demonstrated under working conditions. Calibration information: Measuring arm: last calibration October 2024 LLP HD scanner: calibration date April 24, 2024 Scanner manufactured July 2019 A current recalibration is not included in the offer. The included MetrologyWorks Kodiak HDP-KCF is a professional heavy-duty metrology tripod designed for portable CMM arms and laser trackers. It features carbon-fiber/aluminium construction and a universal 3½"-8 mounting ring. Original technical documentation is available. Please note: The laptop and PolyWorks software shown in some pictures are not included in the sale. Inspection and live demonstration are possible by appointment in Gabčíkovo, Slovakia. EU-wide insured shipping can be arranged at the buyer’s expense. Personal collection is also possible. Price: EUR 24,900 net, negotiable.