Used Brass Tubes for sale (2,196)

Condition: used, Year of construction: 1998, power: 7 kW (9.52 HP), Manufacturer : Axomatic srl Model: Optima 900 Matic Year : 1998 Type : Plastic tube filler Max capacity : 70 units / min Dosing range : 2 ml - 300 ml Max tube length : 280 mm with cap Nedpfx Aasx Ar Sbj Eolk Tube diameter: 10 mm - 60 mm Power : 7 KW Current: 18 A

Condition: good (used), Stuffing box for screw conveyors, transport screws, screw conveyors, conveying technology, pipe screw conveyors, drying screws, cooling screws, cooling tube screws, heating screws, heating tube screws, screw heat exchangers -Stuffing box: for Ø 80 mm shaft -Stuffing box: for stuffing box strap -Bolt circle: Ø 160 mm -Number: 7x stuffing boxes available Njdpfxodfgk So Aa Eslk -Price: per piece -Dimensions: 180/180/H82 mm -Weight: 4.5 kg

Condition: ready for operation (used), AEG / AVITEQ Vibrating tube (only 2 left ) Nljdpfxetznite Aa Eek 1 x : length 3000 mm – diameter 500 mm with two pieces vibration motors of each 1,3 kW 1 x : length 5900 mm – diameter 500 mm with two vibration motors of 2.3 kW each

Condition: new, empty load weight: 3,140 kg, maximum load weight: 7,360 kg, overall weight: 10,500 kg, axle configuration: 2 axles, loading space length: 5,110 mm, loading space width: 2,430 mm, suspension: steel, tire size: 245 / 70 R 17,5, color: other, gearing type: other, front tire size: 245 / 70 R 17,5, rear tire size: 245 / 70 R 17,5, driver cabin: other, emission class: none, Equipment: ABS, compressed air brake, Three-way tipper, loading height approx. 940 mm, front wall foldable for overloading, central locking for side and rear drop sides, automatic rear wall opening when tipping backwards, side walls swinging and foldable, side drop sides with spring assistance, platform floor made of 4 mm fine-grain steel, 8 strong lashing eyes recessed into the floor, 5-stage hard-chromed three-way tipping cylinder, tipping angle: 50 degrees to the rear and 45 degrees to the sides, continuously height-adjustable draw tube, removable rear stakes, gearbox support winch with load and high-speed mode at front, integrated receiver compartment for two aluminum loading ramps in chassis, lockable ramp compartment (privacy protection), contour marking according to ECE R 048 regulation, vehicle with day registration, -- Subject to misprints, errors and changes, sample images --, More data at: !, More details: ! Nsdpfx Aajx Nifns Ejlk

Condition: new, empty load weight: 2,798 kg, maximum load weight: 15,202 kg, overall weight: 18,000 kg, axle configuration: 2 axles, suspension: air, tire size: 385/65 R22,5, Year of construction: 2025, Equipment: ABS, Unladen weight: 2798 kg, permissible gross weight: 18,000 kg, tire size: 385/65 R22.5, 1st axle: , 2nd axle: , air suspension, underride protection, Electronic Braking System (EBS), toolbox, connector plug 1x15 and 2x7 pin, anti-spray, telematics system: TrailerConnect, drawbar with DIN towing eye inner D40mm, outer D110mm, thickness 30mm, drawbar dimensions 2000/1300/100/30, towing tube extendable by 6x100 mm. You can find our complete vehicle range at . Interested in financing? With our Value Added Services, we offer you individual financing options, full service, and telematics solutions. We will be happy to advise you. Nsdox Nlyuspfx Aa Eslk

Condition: good (used), Year of construction: 2012, Technical specifications: Tube Laser Cutting System for round tubes, rectangular tubes, oval tubes Also suitable for open profiles such as U-profiles, flat steel, angle steel Laser: CO2 ROFIN DC 025, 2.5 kW Max. tube diameter: 120 mm Min. square dimension: 12 x 12 mm Max. square dimension: 120 x 120 mm Max. rectangular tube dimension (one side): 140 mm Max. tube weight: 15 kg/m Cutting capacity steel: 8 mm Cutting capacity stainless steel: 6 mm Nodjx Dy Imepfx Aa Eslk Cutting capacity aluminium: 4 mm Cutting capacity brass: 5 mm Cutting capacity copper: 3 mm PRECITEC AK-HP universal cutting head holder Loading: Bundle loading: fully automatic Minimum loadable length: 3,200 mm Maximum loadable length: 6,500 mm Max. loading capacity: 4,000 kg CNC control: Control: SIEMENS Sinumerik 840D SL Extraction system: Performance: 2,000 m³/h Space requirements: Installation area: approx. 14,550 x 4,400 mm Discharge table at the front of the machine Condition: Very good condition, as it has seen little use The seller is not liable for typographical or data transmission errors. The machine's appearance, condition, and wear conform to its age; used machines are sold without any warranty.

Condition: used, Year of construction: 2011, Manufacturer : TGM Model: E250 MATIC Year : 2011 Type : Plastic tube filling and closing machine Closure : hot air device (HA) Max capacity : 60 units / min Transport chain : 10 buckets Empty tubes feeding : automatic Tube centring Sold with 3 simple hoppers and 1 jacketed hopper Nlsdpfjx Akbujx Aa Eek Verification check: no tube – no filling Outfeed conveyor belt Available formats.   General information Tube height: 50 – 240 mm Diameter: Ø 10 mm – 50 mm  

Condition: ready for operation (used), Year of construction: 2011, table length 3050 mm table width 1525 mm Nedpox H Tuuefx Aa Ejlk burner heads 1 Control Mazatrol Preview M Number of working hours 31400 h laser capacity in Watt 4000 max. table load 915 kg max. size of workpiece LxWxH 3050 x 1545 x 25 mm sheet thickness - max. 25 mm height of material-table 375 mm table height over floor 900 mm rapid traverse x / y / z axis 24 / 24 / 25 m/min weight of the machine ca. 14,2 t dimensions of the machine ca. 8 x 2,9 x 2,6 m Well-maintained laser cutting system (CO2 gas laser) with travel distances x/y/ z = 3260 x 1545 x 430 mm, maximum working area: 1525 x 3050 mm, 3rd turning axis NC rotary table for mounting tubes (therefore Z-axis 430 mm), gantry loader with vacuum lifter for feeding new sheets and lifting unit for removing finished sheets, as well as control cabinet with operating elements, tapping unit with drill magazine, automatically retracting protective hood, Donaldson extraction system, cooling system, further technical data available upon request. The gantry loader uses a vacuum lifter to pick up the new sheets, automaticallypicks up the laser-cut sheet during transport, sets the new sheet down, and then moves it to the delivery table for the finished sheet, where it is placed – see video 2. The extraction system, cooling system, and transformer are mounted on the platform above the machine. Mazatrol Preview M control unit with color TFT, 64-bit CPU, 20 GB hard drive, EIA/ISO format programming.

Condition: excellent (used), Year of construction: 2018, operating hours: 3,590 h, functionality: fully functional, spindle motor power: 15,000 W, turning length: 100 mm, turning diameter over cross slide: 51 mm, spindle speed (max.): 5,000 rpm, turning diameter: 51 mm, spindle bore: 51 mm, overall weight: 5,300 kg, rotational speed (max.): 5,000 rpm, type of input current: three-phase, bar passage: 51 mm, feed length X-axis: 165 mm, feed length Y-axis: 80 mm, feed length Z-axis: 590 mm, total width: 1,560 mm, total length: 2,840 mm, total height: 1,700 mm, feed rate X-axis: 20 m/min, feed rate Y-axis: 12 m/min, feed rate Z-axis: 20 m/min, bar diameter (max.): 51 mm, turning diameter over bed slide: 51 mm, turning diameter over top slide: 51 mm, rapid traverse X-axis: 20 m/min, rapid traverse Y-axis: 12 m/min, rapid traverse Z-axis: 20 m/min, input voltage: 400 V, travel distance X-axis: 165 mm, travel distance Y-axis: 80 mm, travel distance Z-axis: 590 mm, power of the servo motor: 15,000 W, Equipment: documentation/manual, rotational speed infinitely variable, 2018 Citizen Miyano BNJ-51 CNC Automatic Lathe – Excellent Condition & Low Hours 2018 Citizen Miyano BNJ-51 Fixed Headstock CNC Automatic Lathe, complete with Iemca Kid 80 Barfeed and full tooling package. This high-precision twin-spindle lathe has only 3,590 cutting hours and comes from a clean, well-maintained production environment. Perfect for precision component manufacturing in medical, aerospace, and automotive industries. Machine Overview Make/Model: Citizen Miyano BNJ-51 Machine Type: Fixed Headstock Type CNC Automatic Lathe Year: 2018 Control System: Fanuc Series Oi-TF Cutting Hours: 3,590 hrs Condition: Excellent – low hours, production-ready Included Equipment & Features Iemca Kid 80 Barfeed Parts Conveyor Swarf Conveyor Parts Catcher Mirror Turning Capability Collet Chuck on Spindle 1 Collet Chuck on Spindle 2 6” 3-Jaw Hydraulic Chuck 8 x Driven Toolholders Full Set of Static Toolholders Technical Specifications Machining Capacities Max. Machining Length: 100 mm Standard Turning Diameter (Spindle 1): 51 mm Standard Turning Diameter (Spindle 2): 42 mm Chuck Size Spindle 1: 6" Chuck Size Spindle 2: 5" Number of Spindles: 2 Spindle Performance Spindle 1 Speed Range: 5,000 rpm Spindle 2 Speed Range: 5,000 rpm Draw Tube ID (Spindle 1): 52 mm Draw Tube ID (Spindle 2): 43 mm Spindle 1 Drive Motor: 15 kW Spindle 2 Drive Motor: 7.5 kW Turrets & Tooling Number of Turrets: 2 Turret 1: 12-Station (Driven Tool Capable) Turret 2: 8-Station (Driven Tool Capable) Square Tool Shank: 20 mm Drill Shank Diameter: 25 mm Driven Tool Speed – Turret 1: 6,000 rpm Driven Tool Speed – Turret 2: 3,000 rpm Driven Tool Motor (T1): 2.2 kW Driven Tool Motor (T2): 0.75 kW Axis Travels X1 Travel: 165 mm Z1 Travel: 246 mm Y1 Travel: 80 mm (+/- 40 mm) Nsdpsxtfqrofx Aa Eolk X2 Travel: 85 mm Z2 Travel: 590 mm Rapid Feeds (X1, Z1, X2, Z2): 20 m/min Rapid Feeds (Y1): 12 m/min Power & Electrical Power Capacity: 33 kVA Machine Dimensions (W x D x H): 2840 x 1560 x 1700 mm Machine Weight: 5,300 kg Highlights Low Cutting Hours: Only 3,590 hrs of light use Full Barfeed & Chip Handling Package – ready for continuous production Twin Spindle / Twin Turret Configuration for maximum productivity Driven Tooling for milling, drilling, and complex part geometry Fanuc Oi-TF Control – industry standard reliability and precision Ideal for precision turned parts in small to medium batch runs Applications This machine is ideal for medical components, automotive fittings, aerospace connectors, hydraulic parts, and general precision turned parts. The combination of twin turrets, high-speed spindles, and driven tooling allows for efficient multi-axis machining with minimal setup time and high repeat accuracy. Condition & Availability The Citizen Miyano BNJ-51 is in excellent mechanical and cosmetic condition and available for immediate inspection or delivery. Citizen Miyano BNJ-51, Used Citizen CNC Lathe, Used Miyano Lathe Ireland, CNC Automatic Lathe for Sale, Citizen BNJ Lathe, Twin Spindle CNC Turning Center, Used CNC Machines Ireland, Fanuc CNC Lathe, Barfeed CNC Lathe, Used Precision Lathes, Citizen Miyano BNJ Series, CNC Turning Machines for Sale Europe, Fixed Headstock CNC Lathe

Condition: new, empty load weight: 2,980 kg, maximum load weight: 8,920 kg, overall weight: 11,900 kg, axle configuration: 2 axles, loading space length: 5,110 mm, loading space width: 2,430 mm, suspension: steel, tire size: 245 / 70 R 17,5, color: beige, gearing type: other, front tire size: 245 / 70 R 17,5, rear tire size: 245 / 70 R 17,5, driver cabin: other, emission class: none, Equipment: ABS, compressed air brake, Three-way tipper, loading height approx. 940 mm, front wall foldable for overloading, central locking for side and rear drop sides, automatic rear wall opening when tipping backwards, side walls swinging and foldable, side drop sides with spring assistance, platform floor made of 4 mm fine-grain steel, 8 strong lashing eyes recessed into the floor, 5-stage hard-chromed three-way tipping cylinder, tipping angle: 50 degrees to the rear and 45 degrees to the sides, continuously height-adjustable draw tube, removable rear stakes, gearbox support winch with load and high-speed mode at front, integrated receiver compartment for two aluminum loading ramps in chassis, lockable ramp compartment (privacy protection), contour marking according to ECE R 048 regulation, vehicle with day registration, -- Subject to misprints, errors and changes, sample images --, More data at: !, More details: ! Nsdpfx Aaox Ngc Ds Eslk

Year of construction: 2011, condition: excellent (used), functionality: fully functional, SICA-TRS 90-500 , PLANETARY TUBE SAW PLANETARY SAW Application: Cutting and Chanfering of PVC, PE, PP PIPES With chip extraction fan Minimum diameter 100 mm Max diameter 500mm Year of construction 05-1994 Central clamp Machine locations: Sachal extrusion machines Nlsdpfxexwd Sps Aa Ejk D-26345 Bockhorn-Grabstede Bahnhofstrasse 6 The machine is my property.

Year of construction: 2010, condition: used, Case maker Kolbus DA 270 Year: 2010 For fully automatic production of book cases, files, display cards, calendar backs or game boards. Description: - Automatic setting - Motorised setting - Automatic case counter - Board pre stacking conveyor: 1700 mm Nljdox Ary Eopfx Aa Eek - Board cutter: PS - Centre strip infeed (flexible) - Waste chopper - Cloth feeder: Non-Stop - Glue unit - Preheated glue tube - Viscosity control - Device for inside lining with hotmelt - Device for producing padded cases - Pressing station - Stacking delivery Max. mechanical speed: up to 65 cycles/min Size range opened case (max): 670 x 390 mm Size range opened case (min): 205 x 140 mm Note!: Specifications are subject to typographical errors and changes in comparable models by the manufacturer!

Condition: used, Year of construction: 1992, power: 4 kW (5.44 HP), Empty weight: 2.400 kg Manufacturer : Norden Model : Nordenmatic 700 Year : 1992 Nledpfx Asx Ai Utea Esk Type: Automatic tube filling and sealing machine Capacity: 70 tubes max Filling volume: 1 - 300 ml Dosing accuracy: +/- 0.1-0.5% Tube size range: Length: 50-250 mm / Diameter: Ø 10-50 mm Empty tube feeding : automatic Cleaning + Tube orientation device with a stepper motor Sealing Module: HA - Hot Air Number of buckets: 22 units Product feed hopper + dosing pump Vulcanic Vulcatherm cooling unit (year: 2004) - 3.5 kW (10°C - 35°C) / Outlet temperature: 25°C max - min 3°C Laminar flow Machine dimensions: 135 x 190 x 210 cm Weight : 2 400 kg Spare parts sold with the machine. Choose from two formats among many available formats (additional formats can be added as an option). Full documentation available Video in operation available

Condition: reconditioned (used), Year of construction: 2002, operating hours: 44,590 h, functionality: fully functional, pressing force: 200 t, filling opening width: 1,020 mm, filling opening length: 2,000 mm, bale width: 1,100 mm, bale height: 1,100 mm, oil tank capacity: 3,100 l, power: 150 kW (203.94 HP), year of last overhaul: 2025, Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Nedpfx Ajx Dnb Uea Eelk Typ 112 Year of construction 2002, partially refurbished in December 2025 Operating hours 44,590 hours, stand December 2025 Press power main press 200 tons Specific press capacity 16,5 kg/cm² Feed channel 2,000 x 1,020 mm Filling volume 2,65 cm³ Theoretic throughput rate 795 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 75 kW Tying system 5-fold horizontal, full automatic Throughput rate at MSW approx. 48 up to 54 tons/h, depends on material Volume hydraulic oil tank 3,100 l Machine weight baler approx. 50,8 tons Scope of delifery: 1 piece baler MACPRESSE, type 111A 1 operating manual with CE declaration, electrical and hydraulic circuit diagram Comments: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Hydraulic oil tank emptied and cleaned • Oil and air filters replaced • New hydraulic oil filled • All hydraulic hoses replaced • Press ram dismantled, broken down into individual parts, mechanics made operational • Front two main rollers replaced • Knives on the press ram replaced • Main hydraulic cylinder dismantled, disassembled, cylinder tube and piston rod checked, complete seal set replaced • Counter knife in the frame replaced • Knife gap adjusted to approx. 3 mm • Upper steel guide rails in the frame on the left and right replaced. • Worn press base cut out, base plate replaced with wear-resistant HARDOX steel. • Binding and twisting unit dismantled, broken down into individual parts, mechanics made functional, all twisting shafts and ball bearings replaced. • All wire rollers in the needle heads replaced • Wire knives cleaned and readjusted, chains greased and tensioned • All wire deflection rollers made operational • All door contact switches replaced • Wirbulator device dismantled, disassembled and made operational • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode, see video for the machine function test. The documentation (BA, CE, electrical/hydraulic circuit diagram) is complete. Viewing is possible by appointment. We accept no liability for the technical specifications or any errors.

Condition: good (used), Ring bending machine, profile bending machine, three-roll bending machine, bending machine, pipe bending tool -Manufacturer: Perthel, pipe bending tool for profile bending machine -Profile diameter: Pipe size 16 - 76 mm / 3/8" to 3 1/4" -Dimensions: 1020/310/H170 mm Nedpfogrzuusx Aa Eelk -Weight: 28 kg

Condition: good (used), Year of construction: 2017, REF: MM5724 Complete automatic volumetric filling and bagging system with PLC control panel, suitable for packing many dried snack-type products such as nuts, seeds, grains, dried fruit, etc, into pillow-packs. The product moves from the opper via a vibrating tray / chute into a turning bowl with cup openings. The amount per cup is then dropped into the funnel through the forming tube into the bag. The size of the cups determines the filling amount. The turning bowl is adjustable in height so even with the same size cup there are various filling sizes possible.  Model - MWM-900 Automatic Form Fill Seal Machine.  Sealing jaws: Horizontal - 260mm. Vertical - 300mm.  Nledpfx Aajt Sw Elo Esk Pack size range - Length: 50mm - 320mm. Width: 140mm (with current forming tube/shoulder).  Speed - up to 30 packs/minute, depending on product size.  Filler - volumetric, 20g-1000g range. Can double drop for larger pack sizes.  Electric supply - 440 V / 50 hz / 3 phase. Features a metal detector at the bottom of the filling tube / inside the forming assembly and has hot foil stamping for printing on pouch. Previously used for packing popcorn. 

Condition: used, Year of construction: 2023, Exhibition machine Garbsen HORIZONTAL PANEL SAW GABBIANI P Manufacturer: SCM Type: GABBIANI P80 Year of manufacture: 2023 1 unit MAIN FEATURES INDIVIDUALLY SELECTABLE AIR CUSHION TABLES: AN INDISPENSABLE TOOL SIDE SAFETY DEVICES: MORE SPACE FOR WORKING FLOATING GRIPPERS: GUARANTEED PERFECT CUT TECHNICAL DATA GENERAL INFORMATION gabbiani p80 Saw blade projection mm 80 Working table height mm 950 Standard number of grippers 5 Number of grippers for versions 33/38/43 9 / 10 / 10 Number of grippers for versions 33/38/43 with FlexCut 1 unit (single gripper with double fingers included) 10 / 11 / 11 CUTTING DIMENSIONS Version 33 mm 3300x2100 Version 33 (Opt.) mm 3300x3200 Version 38 mm 3800x3200 Version 38 (Opt.) mm 3800x3800 Version 43 mm 4300x3200 Version 43 (Opt.) mm 4300x4300 AXIS SPEED Variable saw carriage speed m/min 6 – 60 Variable pusher speed () m/min 60 MAIN SAW BLADE Motor power (S6 -40%) - 50hz (star-delta start) kW (HP) 7 (9) (11) Speed – 50 hz rpm 4650 Saw blade diameter mm 340 Shaft diameter main saw blade mm 80 SCORING BLADE Motor power (S6 -40%) - 50hz kW (HP) 1.5 (2) Speed – 50 hz rpm 5850 Scoring blade diameter mm 200 Shaft diameter scoring blade mm 80 INSTALLATION Installed power kW 12÷15 Base machine voltage Euro voltage (400 V / 50 hz) Compressed air demand NL/min 300 Required compressed air pressure bar 7 Extraction air requirement m3/h 2440 Extraction air speed m/sec 20 Extraction port diameter mm 4x120 () Note: in countries where EU standards apply, the forward pusher feed speed is limited to 25 m/min. GENERAL CHARACTERISTICS Fully automatic, PC/PLC-controlled horizontal panel saw suitable for cutting solid wood, MDF, chipboard, plywood, and similar materials. Frame and working table – Machine frame is a steel tube construction – Working table of rib-reinforced steel with Bakelite coating – Longitudinal fence on the left side Saw carriage made of steel, consisting of: – a motor for the main saw blade and a motor for the scoring blade – vertical lifting of the saw blade on linear ball bearing guides and shoes – running rollers of hardened and ground steel – balanced mass distribution for optimal cut quality – running direction towards the longitudinal fence – saw carriage drive via rack and pinion – carriage travel on cylinder guides – cylinder guides of hardened and ground steel (5-year warranty), protected by special dust wipers – pneumatic switch for fast and safe main and scoring blade change Pressure beam – pressure beam with uniform pressure across the entire cut length, recesses to prevent collision with grippers; pneumatic height adjustment via high-precision rack and pinion, pressure adjustable from 1.5 to 6 bar – dual extraction system with one unit above the pressure beam for cleaning the work table and one unit below on the saw carriage – side automatic aligner with pneumatic cylinder over the entire length. Sliding on linear ball bearing guides and shoes. * Travel distance: 1200 mm * minimum working width: 60 mm * maximum working width: 1200 mm Positioning pusher and rear part of the machine – Positioning pusher full length, powered by a robust drive shaft. Positioning pusher control... Njdpfxsxyl U Rs Aa Eslk

Condition: used, Cheese whey processing plant 15,000 Litres/Hour Plant consists of:- 250 litre stainless steel tank 15,000 litre/hr product pump complete with 5.5kw motor Nljdpfexxi R Tjx Aa Eok Tetra plex C8 SR plate heat exchanger SWEP gasketed hot water preparation unit Hot water pump complete with 3.0kw motor Automatic steam on/off valve Steam modulating valve Steam trap & Filter Holding tube for 25 seconds at 15,000 litres/hour in 3" pipe pipping and valving including 3 off x 2" 3 port flow divert valves RTD's for hot water, hot whey & cold whey High level probe for the balance tank connection to UF Allen bradley for operation Full complete specification can be sent on request.

Condition: like new (used), Year of construction: 2023, Mandrel Bending Machine S4501 ---- For the production of pipe geometries with bending radii from 1.5xD → Maximum bending capacity: pipe 42.4 x 3.25 mm (steel max. Re 240 N/mm²) → Maximum bending capacity: pipe 30 x 30 x 3 mm → Maximum bending capacity: pipe 42.4 x 2 mm (stainless steel max. Rp0.2 260 N/mm²) → Total connected load 3 kW → Pipe insertion length approx. 1.5 m Robust and durable steel construction. Maintenance-free servo drive for the bending, feed, and twisting axes. The control system's touchscreen display enables simple and intuitive programming and operation of the system. After the pipe is inserted, it is secured in the carriage by the chuck. This enables precise positioning of the pipe and thus the creation of dimensionally accurate geometries. The standard also includes a check of the pipe geometry before the bending process: If the bending process is started in the wrong position, the machine will not issue a release. This eliminates the risk of incorrect operation. Optional additional features provide greater convenience and increase output, thus increasing the efficiency of the system. Data exchange from the optional TBS-3D pipe calculation program (PC version) takes place via USB stick or network. Existing pipe geometries can be imported using the software. Standard equipment: → 1.5 kW servo drive for the bending axis → Adjustable speed → Left-hand bending direction → Bending angle resolution 0.1° → Max. bending radius 120 mm → Bending shaft diameter 50 mm → Feed servo drive → Rotation servo drive → Three-jaw chuck for locking the tube in the carriage → Pneumatic tool retraction Hydraulics: → Hydraulic tube clamping with adjustable clamping pressure → Programmable early mandrel retraction PLC control: → 10" color touchscreen → ETH 10/100, X2X Link, 2xUSB → Foot switch operation → Data transfer via LAN or USB network → Material database Unique graphical programming: Simple geometries can be calculated directly on the machine. The control system calculates the feed values and bending angles directly after entering the length and angle. Nedpfxetr U Hlo Aa Eelk Power consumption: 400V 16A Dimensions: L: 2.3 m x W: 1m x H: 1.4m Weight: approx. 1200 kg

Condition: good (used), AF/Armafix pipe supports, pipe supports -Manufacturer: Armacell, Armafix AF pipe support FX-2-60/64 AF-2 box with 24 pcs. -Article No.: 38407000 -Tube: Ø 60/64 mm Nljdpfxjt Acwhj Aa Esk -Quantity: 5x box available -Price: per box -Dimensions box: 390/200/H200 mm -Weight: 1,5/pc.

Condition: new, functionality: fully functional, Year of construction: 2025, Manual Pipe Bender HRB-3D 850 for bending pipes and solid material up to a maximum of 12 mm Precise positioning and repeatable bending are ensured by three battery-operated digital displays that precisely show the bending angle, pipe feed, and pipe twist. - 80 mm three-jaw chuck - Feed stop system - Feed length approx. 850 mm The manual pipe bender should be permanently mounted on a table or frame (not included). We would be happy to provide you with a detailed quote if you send us your complete company address, email address, and contact details. Nedpfxettagds Aa Eslk

Year of construction: 2009, condition: good (used), hydraulic cylinders, support cylinders, hydraulic rams, pressure rams -Pressure force: at 250 bar 96 to -Piston diameter: 220 mm -Piston rod: Ø 125 mm -Cylinder tube outside: Ø 260 mm -stroke: 495 mm Nsdjdq U S Ispfx Aa Eslk -Total length retracted center hole: 1195 mm -Piston rod mount: Ø 100 mm -Cylinder mount: Ø 100 mm -universally applicable: -Number: 15x cylinders available -Price: per piece -Dimensions: 1360/530/H300 mm -Weight: 364 kg/piece

Condition: used, Year of construction: 2017, pipe diameter (max.): 80 mm, mandrel length: 4,500 mm, Mandrel bending machine S8004 ----- For the production of dimensionally accurate pipe geometries with bending radii of up to 1.5XD → maximum bending performance pipe 76 x 4 mm (400 N/mm²) → maximum bending performance pipe 60 x 60 x 3 mm (400 N/mm²) → maximum bending performance pipe 76 x 2.9 mm (stainless steel) → total connected load 7 kW → pipe length 4.5 mtr Robust and durable steel construction in a force-locking connection - no construction susceptible to torsion due to, for example, the split construction of the bending head and mandrel carrier. Maintenance-free electromechanical drive of the bending axis. The touch display of the control enables simple and intuitive programming and use of the system. After the pipe has been pushed on, it is fixed in the carriage by the chuck. This enables the pipe to be positioned precisely and thus the creation of dimensionally accurate geometries. The standard also includes checking the pipe geometry before the bending process: If the bending process is started in the wrong position, the machine does not give permission for this. This prevents incorrect operation. Optional additional features provide more convenience and increase the output and thus the efficiency of the system. Data is exchanged from the optional pipe calculation program TBS-3D (PC version) via USB stick or via FTP access from the computer to the machine control system. USB or LAN connectors (RJ45) are available as standard. Existing pipe geometries can be converted quickly and easily, for example, using the STEP format. Standard equipment: → Electromechanical drive of the bending axis 4 kW → Speed 2.9 rpm (=17°/sec.) → Bending direction left → Bending angle resolution 0.1° → Max. bending radius 200 mm → Bending shaft diameter 50 mm → Electronic length measurement ±0.1mm → Electronic twist measurement ±0.1° → Manual stop system (overtravel stops in length) → Manual locking system (15° in twist) → Three-jaw chuck for locking the pipe in the carriage → External control panel PLC control: → Touchscreen 10.1" → ETH 10/100, X2X Link, USB → Foot switch operation → Data transfer via network (W)LAN or USB → Material database Unique graphic programming: Simple geometries can be calculated directly on the machine. The control calculates the feed values directly after entering the length and angle and the bending angles. Hydraulics: → Hydraulic power 3 kW → Hydraulic pipe clamping with adjustable clamping pressure → Programmable early mandrel retraction Options (can be ordered as additional equipment): → Variable bending speed using frequency converters or servo motors → Automatic tool retraction (manual or controlled) → Pneumatic chuck → Automatic mandrel lubrication → Pneumatic stop system (length + twist) → Mobile version (rollers) → Radius extension Pictures show new machine Nodpfx Aaottah Rj Eolk

Condition: good (used), Hydraulic cylinder, support cylinder, hydraulic piston, pressure piston -Cylinder: approx. Ø 90 mm -Piston rod: Ø 60 mm -Pipe outer diameter: 120 mm -Stroke: 940 mm Nledpjchaynjfx Aa Esk -Total length when retracted: 1510 mm -Piston tube mounting: Ø 25 mm -Piston rod mounting: Ø 35 mm -Ideal for building a hydraulic press -Quantity: 1 piece available -Weight: 80 kg

Condition: good (used), Hydraulic cylinder, support cylinder, hydraulic piston, pressure piston -Piston rod: Ø 50 mm -Piston tube outer diameter: Ø 135 mm -Stroke: 300 mm Nsdjb A Itvspfx Aa Eolk -Weight: 52 kg