Used Adhesive Application for sale (8,512)

Condition: used, tank capacity: 2,765 l, GENERAL Design: suspended Comments: Vessel externally sandblasted and primed; double jacket bolted to lower end plate (see photos); 4 mounting lugs made of steel; exterior surface partially corroded (may require repairs) Speed: 167 RPM Internal diameter: 1,400 mm Explosion protection: Motor is explosion-proof (compliance with current ATEX regulations under local conditions must be verified) Total height: 3,350 mm Heating/Cooling: available Power: 2.6 kW Max. permissible operating temperature: 150 °C Max. permissible operating overpressure: 3.0 bar Max. overpressure: 6.0 bar Agitator: propeller Support type: mounting lugs Location: Bremen Technical documents: drawing, TÜV certificates Nameplate: Vacuum: 1.0 bar Volume: 2,765 liters Double jacket volume: 42.0 liters Cylinder wall thickness: 7 mm Double jacket material: V2A 1.4541 (AISI304) Product-contact material: V4A 1.4571 (AISI316) Condition: used Kdedpfxsxqa R Ue Ag Uog Cylindrical height: 1,390 mm Last application: chemicals VESSEL Max. permissible operating temperature: 200 °C HEATING/COOLING JACKET Bottom temperature control: double jacket EQUIPMENT Outlet: flange DN80 Note: slight residues/adhesions AGITATOR 1 Agitator manufacturer: Ekato Voltage: 500 V Interference suppressor: TECHNICAL DATA / DIMENSIONS Lower end plate thickness: 7 mm Agitator arrangement: centrally mounted on upper end plate Upper end plate thickness: 9 mm

Condition: used, tank capacity: 10,875 l, GENERAL Equipment: Crane lugs Design: Suspended Remarks: Support ring made of Fe; In some areas, the flanges of the top head were welded on the inside with a stainless steel sheet by the previous operator (in some of these sheets, an opening has been cut – see photos); Manhole diameter 480 mm Kdsdpoxqa Nwsfx Ag Ueg Speed: 78 rpm Internal diameter: 2,170 mm Total height: 5,050 mm Heating/cooling: available Power: 22 kW Max. permissible operating temperature: 220 °C Max. permissible operating overpressure: 20.0 bar Max. overpressure: 6.0 bar RW Sealing: Mechanical seal with thermosiphon vessel Agitator: Anchor agitator Standing form: Ring Location: Bremen Cylinder temperature control: Half-pipe coil Nameplate: Vacuum: 1.0 bar Volume: 10,875 liters Double-jacket volume: 330.0 liters Cylinder wall thickness: 8.7 mm Double-jacket material: V2A 1.4301 (AISI 304) Product-contact surface material: V2A 1.4541 (AISI 321) Condition: Used Cylindrical height: 2,200 mm Previous application: Adhesives industry VESSEL Max. permissible operating temperature: 200 °C HEATING/COOLING JACKET Max. permissible operating vacuum: 1.0 bar Bottom temperature control: Half-pipe coil EQUIPMENT Manhole / Dome: in top head Outlet: present Note: minor residues, manhole cover missing Outlet: 100 mm MATERIAL SPECIFICATION Flange material: Steel AGITATOR 1 Agitator manufacturer: Ekato Voltage: 230/400 Volts TECHNICAL DATA / DIMENSIONS Bottom wall thickness: 11.4 mm Agitator arrangement: central in top head Top head wall thickness: 14 mm

Condition: used, Year of construction: 2007, tank capacity: 29,000 l, GENERAL INFORMATION Design: vertical Year of manufacture: 2007 Notes: Manhole diameter top head: approx. 700 mm; Manhole diameter shell: approx. 500 mm; Speed: 40 rpm External diameter: 3,200 mm Internal diameter: 2,980 mm Total height: 6,800 mm Heating/Cooling: available Power: 75 kW Max. pressure: 0.6 bar Agitator type: beam agitator Support type: legs Location: outdoor storage Technical documentation: drawing, CE marking and declaration of conformity Cylinder temperature control: double jacket Nameplate: Vacuum: 1.0 bar Volume: 29,000 liters Kdjdpfx Asxqat Nog Ujg Double jacket volume: 4,100.0 liters Cylinder wall thickness: 8 mm Product-contact material: V4A 1.4571 (AISI 316) Condition: used Cylindrical height: 3,368 mm Last application: adhesive production VESSEL Max. permissible operating temperature: 100 °C Specific medium weight: 1.3 (to/m³) Number of legs: 4 pieces HEATING/COOLING JACKET Bottom heating/cooling: double jacket EQUIPMENT Manhole / dome: in the shell, in the top head Outlet: DN 125 mm AGITATOR 1 Agitator manufacturer: PRG Voltage: 400 Volt Bottom bearing: TECHNICAL DATA / MEASUREMENTS Bottom wall thickness: 9 mm Agitator positioning: central, in top head Top head wall thickness: 7 mm

Condition: good (used), Year of construction: 1990, 10310 Direct Mailing Line - Highly flexible machine for the production of direct mailing products and a variety of other applications, consisting of: - MBO R-105 round-pile feeder - Vacubelt infeed - Compressor - MBO control panel - Hunkeler Mini-Mailer 1, processing station equipped with/for: - Various register-perforating heads for both intermittent and continuous operations (perforating, creasing, slitting, etc.) - 1 ROBATECH glue system for remoistenable adhesive (hotmelt also possible), with various application heads - Dispersion adhesive system with multiple application heads - Plow fold device (for sheet doubling, etc.) - Hunkeler control unit (six-channel controller) for all register functions - Transfer to - Hunkeler Mini-Mailer 2, processing station equipped with/for: - Various register-perforating heads for both intermittent and continuous operations (perforating, creasing, slitting, etc.) - 1 ROBATECH glue system for remoistenable adhesive (hotmelt possible), with various application heads - Dispersion adhesive system with multiple application heads Kdjdpfx Agox R Utyo Uog - Hunkeler control unit (six-channel controller) for all register functions - MBO FW2-81/8 folding station with 8 folding pockets - Segmented folding rollers - Window folding pocket - Shingled belt delivery - Comprehensive set of processing tools - Central compressed air supply required!

Condition: used, Year of construction: 2008, functionality: limited functionality, travel distance X-axis: 510 mm, travel distance Y-axis: 510 mm, travel distance Z-axis: 150 mm, For sale is the dosing system described below, including a 2-component dispensing unit and a 2-component mixer. However, other dispensing units for the application of sealants, adhesives, lubricants, etc. can also be mounted on the unit. Technical Data Tabletop Robot GLT JR-2503N-H: • Three-axis tabletop robot • Manufacturer: GLT Pforzheim (Gesellschaft für Löttechnik) • Maximum travel distances: 510 / 510 / 150mm (X/Y/Z) • High version • 3-axis interpolation • With 16 inputs and 16 outputs for controlling external units • With control unit for programming • Internal memory storage • Mounting bracket/plate for valve or cartridge • Includes complete production cell (structure made of aluminum profile with base plate and acrylic safety enclosure, as well as light curtain incl. evaluation unit) Kdodpfx Agsx Tqmbj Uog 2-Component Dispensing Unit/Mixer • 2-component dispensing unit with control device and mixing system • EFD Performus III • GLT 2000KTS • Includes accessories (mixing units, cartridges, etc.) Condition The entire system was manufactured in 2008 – the dosing system was only used for demonstration purposes and never in productive operation, and is therefore in very good condition. Only tests and feasibility studies were performed on the system, meaning it has very few operating hours.

Condition: used, Holz Her STREAMER 1057 XL FÜ + PU Edge thickness: 0.4 - 6 mm Modern control unit with selector switch for aggregate settings Fully automatic edge magazine for roll and strip material Glue application station GLU-JET cartridge + PU bonding Adhesive application via nozzle technology Touch-sensitive nozzle Workpiece height: 6-60 mm Automatic glue height adjustment High-quality 3-roller pressure unit, 1st roller motorized Pneumatic end trimming unit for roll and strip material up to 6 mm edge thickness Pneumatic adjustment of trimming saws from 0-10° angle Milling unit: flush trimming 6 mm, radius milling - bevel milling - 15° Corner copying unit - 3 mm edge thickness Scraper unit for chamfers and radii with 2 scraper holders Surface scraper unit - finish Buffing unit Spraying device in infeed and outfeed areas, as well as for PU Machine supplied with all working units/tools Kdedpfx Aex Ux U Asg Ujg Machine is WORKSHOP TESTED First delivered in 2016 Available ex stock Lieboch

Condition: used, Year of construction: 2008, Used machine Year of manufacture: 2008 Kdodpfx Ajwx Aaqog Ujg Condition: well-maintained, serviced regularly (last service by Homag in 11/2024) Features and technical specifications: Minimum workpiece thickness: 12 mm Maximum workpiece thickness: 60 mm Minimum workpiece size (L×W): 240 × 55 mm (with 22 mm thickness) / 100 mm (with 60 mm thickness) Minimum edge thickness: 0.3 mm (roll material) / 0.4 mm (strip material) Maximum edge thickness: 3 mm (roll material) / 20 mm (strip material) Feed speed: infinitely variable, 18–25 m/min (frequency-controlled) Type of glue: EVA hot-melt adhesive Glue application (pot / cartridge / nozzle): melting unit with granulate hopper Glue volume / cartridge size: granulate hopper, melting capacity 18–35 kg/h, level-controlled Heat-up time: approx. 8–10 min Edge magazine (slots): 2 rolls (automatic roll change) Automatic edge change: yes (automatic via PC22, can be switched manually) Pre-milling: 2 × 1.5 kW, 200 Hz, 12,000 rpm, pneumatically adjustable Pressure zone: 1 pre-press roller Ø 150 mm + 6 post-press rollers Ø 70 mm, automatic adjustment End trimming: HL84 trimming unit, 2 × 0.8 kW, pneumatically adjustable (bevel / straight) Flush milling: via pre-milling unit, pneumatically adjustable Radius milling: FK13 contour routing unit, automatic 8-position tool changer (R = 2 mm) Bevel/profile milling: yes, via FK13, pneumatically adjustable Scraper: integrated in multi-finishing unit MN21 Polishing: buffing unit in finishing module FA11 Jointing unit: jointing milling unit KAL310/A20/S2, 2 × 3 kW Workpiece pre-heating: available Release agent spraying device: top / bottom, type 2929 (F.01) Extraction ports: multiple Ø 100 mm (individual extraction per unit) Control: power control PC22 (industrial PC, woodCommander on Win XP embedded) Operating voltage: 400 V, 50 / 60 Hz CE / Standards: CE-compliant according to EU Directive 98/37/EC Dimensions / required space: approx. 8,000 × 1,400 × 1,600 mm Weight: approx. 3,000 kg The return conveyor system visible in the pictures is not included in the scope of supply! Availability: short-term Location: 63934 Röllbach

Condition: excellent (used), Year of construction: 1984, For sale: professional Robatech RoBa 30 adhesive melter, Swiss-made (Robatech AG CH-5630 Muri). The unit is fully functional, complete, and ready for operation. Ideal for packaging lines, folder-gluer machines, cartoners, and equipment requiring precise hotmelt adhesive application. Technical specifications: * Model: RoBa 30 * Year of manufacture: 1984 * Output: 900 g/min * Max hydraulic pressure: 40 bar Kdjdpfoum Hufox Ag Uog * Max air pressure: 5 bar * Max operating temperature: 200°C * Power supply: 240 V * Power consumption: 10 A * Pump ratio: 1:8 * Nameplate legible, pressure gauge operational Condition: * device in good technical condition * complete, with no missing parts * Swiss quality – very robust construction

Condition: used, The Robatech Roba 40 nozzle glue system is a specialized adhesive application system designed for precise and efficient gluing operations. Manufactured by Robatech, this model is located in Germany, with pricing available upon request. The system is equipped with a 40 nozzle configuration, ensuring accurate and consistent adhesive application for various industrial and manufacturing needs. Format: Ksdpfx Aevphziog Uedg Equipment: 40 nozzles for consistent adhesive application

Condition: used, The Eigenbau (Self-build) Perfect binder with PUR is a specialized binding machine designed for precise and efficient bookbinding. This machine is manufactured by Eigenbau and features a perfect binding mechanism with PUR (Polyurethane Reactive) adhesive, ensuring durable and high-quality binding. The machine has a format of 100 mm and is currently available in stock. It is located in Germany, and the price is available upon request. The delivery terms are FCA (Free Carrier), meaning the seller delivers the goods, cleared for export, to the carrier appointed by the buyer. Key features of the Eigenbau Perfect binder include a centering function for accurate alignment, a heating roller for optimal adhesive application, and a miniature circular saw for precise cutting. Additionally, it comes with a paper unwinding mechanism and a PLC (Programmable Logic Controller) for automated control. There is also an optional INATEC BS 25002 PUR system available for an additional 1500 EUR, which can enhance the binding process. The machine is equipped with an input station that includes a plate lifting station for efficient material handling. Format: 100 mm Equipment: Kdedpfxevfx Rto Ag Usg Centering function Heating roller Mini circular saw Paper unwinding SPS control Optional INATEC BS 25002 PUR ( 1500 EUR extra) input station with plate lifting station

Condition: used, tank capacity: 225 l, GENERAL INFORMATION Kdedpexqatvofx Ag Ujg Features: crane lugs Design: vertical Notes: 4-legged frame made of V2A; handhole diameter approx. 155 mm Speed: 156 - 838 rpm Outer diameter: 800 mm Inner diameter: 590 mm Explosion protection: Motor is explosion-proof (compliance with applicable ATEX regulations under local conditions must be verified) Total height: 2,400 mm Heating/cooling: available Insulation: available Power: 0.75 kW Max. permissible operating temperature: 95 °C Max. permissible operating overpressure: 4.0 bar Max. overpressure: 1.0 bar Top cover: removable/hinged top cover Shaft seal: mechanical seal with thermosiphon vessel Agitator: propeller Base design: frame Location: Bremen Cylinder temperature control: double jacket Nameplate: Vacuum: 1.0 bar Volume: 225 liters Double jacket volume: 60.0 liters Product-contact material: V4A 1.4571 (AISI316) Condition: used Last application: chemical industry VESSEL Max. permissible operating temperature: 95 °C HEATING/COOLING JACKET Bottom temperature control: double jacket INSULATION Insulation jacket: hermetically welded Insulation jacket material: stainless steel EQUIPMENT Manhole: handhole Note: slight adhesions Outlet: 25 mm MATERIAL SPECIFICATIONS Temperature control system material: V2A 1.4301 (AISI304) AGITATOR 1 Agitator manufacturer: Stelzer Voltage: 220/380 Volt Interference suppressor: Agitator arrangement: centrally in top cover Agitator features: speed adjustable via handwheel

Condition: used, Year of construction: 2011, Used machine Year of manufacture: 2011 Condition: Machine completely overhauled and serviced Equipment and technical specifications: Infinitely variable feed speed: 10–18 m/min Edge Control 19 control system with 18.5" touchscreen color display Jointing milling unit Edge feeding Cartridge adhesive application station with sensing nozzle and automatic glue height adjustment Pressure unit End trimming unit Multifunctional milling unit Corner copying unit Radius scraper unit Surface scraper Buffing unit Workpiece thickness: 6–60 mm Edge thickness: 0.4–8 mm Minimum workpiece width: 60 mm Shortest workpiece length: 180 mm Ksdpfxjwka N Tj Ag Uedg Dimensions: 5300 x 1500 x 1600 mm Weight: 2,200 kg Location: 65439 Flörsheim Availability: short notice

Condition: used, Second hand line by TANG OG WEISS AS (DK) for packaging liquids into plastic bottles. Volume range from 50 ml to 750 ml. Working output of line: - for bottles volume 750 ml - up to 600 pcs/h - for bottles volume in range from 200 up to 400 ml - in range from 800 - 900 pcs/h, - for smaller volume bottles it is possible to assume a capacity in the range of 1000 to 1200 pcs/h. The line consists of: - Container of bottles produced by PACKFEEDER S.L. (Spain) model MN 100-4, - Filling-closing unit manufactured by TANG OG WEISS AS (DK) model TWKS. It includes filling module by TANG OG WEISS AS model TWRF, with two filling nozzles, stainless steel buffer tank with total volume 15 l, rotary table, caps feeder, arm for capping/cap tapping and plate conveyor, - Stainless steel lobe pump manufactured by SSP PUMPS (England) model L2-0017, for feeding the product to the buffer tank, Kdodsx Tifijpfx Ag Ujg - Labelling unit, by EME Etiketteringsmaskiner ApS. (Denmark) model 4-120 (4000 series) without printer, equipped with a plate conveyor, two pieces of self-adhesive label applicators (front and back of the packaging). Label feed height range: from 20 mm to 120 mm, label feed width range: from 10 mm to 250 mm, operating speed: 0-40 m/min, - Automatic packaging machine in heat-shrinkable film by SKINETTA PAC-SYSTEME GMBH & CO. (Germany) model ASK 450. The device wraps packages of 6 bottles with film and thermoform it. The entrance opening to the foil shrinking section has the following dimensions: width 440 mm, height 320 mm (year of manufacture 1994, no documentation), - Plate conveyors and control panels. The equipment includes a cabinet with formats for oval bottles with volumes: 50 ml, 200 ml, 400 ml, 750 ml, as well as manufacturer's documentation in Danish and a user manual in Polish. The line was produced in 2007.

Condition: excellent (used), Hebrock 3003 Edge Bander well equipped, can be tested before purchase Initial MILLING AirTronic zero joint glueless system - hot air glue application with a roller, pneumatic preliminary guillotine pressure rollers anti-adhesive fluids finished cutting saw top-bottom milling unit, R1 - R2 pneumatically adjustable corner milling unit pneumatically adjustable flat scraper max element height 50mm max veneer thickness in roll 3mm feed 10m/min power consumption 15.8KW very good condition, fully fulfills its functions Kdodowmc I Djpfx Ag Usg

Condition: ready for operation (used), Year of construction: 2010, Additional Equipment Gluing Unit for Hot-Melt Adhesive: Single roll/strip magazine for roll material up to 3 mm and strips up to 12 mm End Trimming Unit: 2 motors, each 660 W, pneumatic swiveling 0° + 25° Kdedpfxox D I D Ae Ag Uog This IMA Combima/II/390/B/L12 was manufactured in 2010. A robust double-sided edgebander, it features a max feed width of 3,300 mm and handles workpiece thicknesses up to 60 mm. Equipped with ICOS OPEN control for precision, it supports both roll and strip edgebanding materials. Ideal for high-capacity environments requiring flexibility and reliability in edge finishing. Contact us for more information about this machine. Application Types Edge Banding

Condition: ready for operation (used), Year of construction: 2006, This IMA Combima Systems/I/R75/1370 edgebander was manufactured in 2006. It handles workpieces ranging from 250 to 2800 mm in length and 115 to 1300 mm in width, with thicknesses up to 40 mm. Designed for materials like chipboard and MDF, it features a hot melt adhesive applicator and a servo edge feed system. Ideal for high-quality edge banding, consider the opportunity to buy this IMA Combima Systems/I/R75/1370 edgebander. Contact us for more information about this machine. Kjdpfxox D I Hqe Ag Usdg Application Types Edge Banding

Condition: new, Year of construction: 2026, functionality: fully functional, total width: 2,000 mm, total height: 4 mm, warranty duration: 12 months, PROFESSIONAL TECHNICAL BLACK FELT Kdjdox Rp U Sopfx Ag Ujg for manual and automatic glass cutting tables We offer high-quality technical black felt designed for covering the tops of glass cutting tables – both manual and automatic. The felt provides effective protection for glass sheets, ensures stable material handling, and maintains high durability even during intensive, everyday use. The product is used by leading manufacturers of machinery for the glass industry. Applications: - Manual glass cutting tables - Automatic and semi-automatic tables - Assembly and workstations Key features: - Deep, intense black color - High density and excellent abrasion resistance - Stable structure and uniform surface - Suitable for industrial use - Proven in professional glass processing plants Technical specifications: - Roll width: 200 cm - Thickness: 4 mm - Chemically hardened on one side - Sold by the running meter - Mounting: contact adhesive Why choose our product: - A solution dedicated for professionals - Enhances quality and workplace safety - Extends the service life of table surfaces - Product ready for immediate application

Condition: as good as new (ex-display), Year of construction: 2022, functionality: fully functional, workpiece height (max.): 50 mm, edge thickness (max.): 3 mm, working height: 900 mm, space requirement height: 1,400 mm, space requirement length: 4,050 mm, space requirement width: 1,300 mm, operating pressure: 7 bar, with PLC control system (including touchscreen) and hot-melt adhesive application to the workpiece for edge materials up to 3 mm: joining cutter (including DIA tool), up to 2 mm cutting depth (max. 1 mm for special materials such as multiplex), maintenance-free glue pot with quick-change pot preparation including glue discharge device, HF trim saw station (approx. 12,000 rpm), HF milling station (approx. 12,000 rpm) with separate pneumatic adjustment and interchangeable cutter (combined version), corner round milling unit, surface scraper (including pneumatic lift), robust chain feed, ball-bearing double roller upper pressure, viewing window from machine rear side, extendable workpiece support, feed rate approx. 10 m/min. Complete with quick-change set-up for corner milling unit, radius scraper (including pneumatic lift), chassis Kedpox E N Nfsfx Ag Usdg F 4 – Technical Specifications Max. edge thickness: 3 mm Min. / Max. workpiece thickness: 8 – 50 mm Min. workpiece length: approx. 160 mm Feed speed: 7 m / min Ready for operation: approx. 3.5 min Max. power consumption: ∅ approx. 7.4 kW Electrical connection: 400 V / 3 Ph / 50 Hz Worktable height: approx. 900 mm Machine dimensions: approx. 4050 x 1300 x 1400 mm (L x W x H) Weight: approx. 820 kg Extraction port: ∅ 1 x 140 mm

Condition: good (used), Code: 0465 Brand: IDM - SCM GROUP Model: IDIMATIC 49-20 Automatic edge bander for the application of edges in wood, pvc, veneer, melamine, abs for furniture, furnishings, kitchens, bathrooms, doors, panels and various Technical data: Min/max gluing height mm 10/50 Min/max edge thickness mm 0,4/20 Min panel width mm 60 Min panel length mm 140 Adjustable feed speed m/min 12/18 Electric press lift Telescopic support for large panels Soundproof cabin Composition: Anti-adhesion unit: spreads anti-adhesive liquid on the upper and lower surfaces of the panel Gluing unit with pre-melting unit Pressure rollers End trimmer unit for front and rear vertical cutting of excess edging - N° 2 motors 0,5 Kw at 12000 rpm - Tool diameter mm 110 Top/bottom trimmer unit with superimposed motors for trimming the upper and lower sides of the excess edge band - N° 2 motors 0,5 Kw at 12000 rpm Top/bottom trimmer and beveller unit for final upper and lower trimming of excess edge band - N° 2 motors 0,5 Kw at 12000 rpm Manual turret device - automatic positioning of the tool post and front copiers according to the different edge band thickness Routing unit makes through holes and non-through holes in the edged side and on the upper and lower parts of the panel and is time controlled Cleaning unit for brushing and polishing of the edge bands applied - N° 2 motors 0,18 Kw at 1400 rpm which can be inclined vertically between 0° and 30° Kdodpfx Agovhc E He Ueg Compressed air 7-8 bar Overall dimensions mm 5600 x 1000 x 1500 h Weight kg 2500

Condition: refurbished (used), Introducing the Rovema VPL 260 Doypack + Reclose (Adhesive Strip) (VFFS)! Designed for flexibility and performance, the Rovema VPL 260 Doypack offers top-tier packaging solutions for a wide variety of products. With its sturdy construction and efficient design, this machine handles everything from pasta and cereals to sweets, pet food, and more. The VPL 260 delivers an impressive output of up to 70 bags per minute, offering a range of packaging options, including block bottom bags, and Ro pack bags with a zip. With the added reclose (adhesive strip) feature, it ensures maximum convenience for both the producer and end consumer. Key Features: • Brand: Rovema • Model: VPL 260 • Capacity: Up to 70 bags/min • Applications: Granules, pasta, cereals, grains, seeds, granola, muesli, sweets, candy, nuts, dried fruits, pet food, crackers, cookies, tea, dry pasta, and more • Packaging types: Block bottom bags, Ro pack bags with zip, Stabilo bags • Construction: Robust design for durability Kodpfx Agox Ag Nue Usdg • Control system: User-friendly interface • Warranty: 3 months • Delivery time: On request Optional extras: Stabilo/Doy packaging, resealing strip (adhesive), and more – fully customizable for your specific needs. DL Packaging specializes in modernizing dosing systems, vertical form-fill-seal machines, cartoners, and end-of-line packers. Our "Second Life Packaging Solutions" are rebuilt to like-new standards and can be integrated into fully automated lines, all from a single source. With over 30 years of experience, in-house dosing expertise, and tailored advice, we ensure your machine or line is perfectly suited to your needs. We also offer remote support, maintenance contracts, and a warehouse with 20,000+ parts for seamless production. DL Packaging – your global partner for retrofitted packaging solutions, based in Oosterhout and a proud partner of the Rovema Group.

Condition: used, Year of construction: 2019, functionality: fully functional, machine/vehicle number: AN2018080, total length: 12,860 mm, total width: 4,806 mm, type of input current: three-phase, input voltage: 400 V, feed length X-axis: 3,000 mm, working width: 350 mm, power: 25 kW (33.99 HP), TRC 1500 – Timber Repair & Cosmetic Machine Technical Description • System Overview • Process Workflow System Overview The Wintersteiger TRC 1500 is a fully automated industrial system designed to detect, repair defects in wooden boards. It combines advanced 3D scanning, high-pressure thermoplastic injection technology to deliver consistent, high-quality repairs at production speed. Defects are repaired with thermoplastic filling material using injection and application units. No filling material is wasted thanks to the precise calculation of the filling quantity and precision injection. the edges can also be filled. Key Features • Automated 3D laser triangulation defect detection • High-pressure thermoplastic injection for durable repairs • Precision finishing unit for cosmetic perfection • Independent melt temperature zones with 8 kg tank • Closed glycol-water cooling system for controlled solidification • Ethernet-based control system with remote maintenance • Unlimited product profiles and intuitive scanner interface Product Range (Workpiece Specifications) Length 500–3000 mm Width 100–350 mm Thickness 3–30 mm Production speed upto 10 m/min – depending on number and sizes of defects Filling System – Injection & Application Units • Injection Unit: • 3-axis positioning (X/Y servo-driven, Z pneumatic) • Pressure-regulated melt feed • High-pressure injection • Application Unit: • 3-axis control • Fine finishing of repaired areas Faulty Spot Eye Scanner • 3D laser triangulation and high-speed camera system. • Detects defects from approx. 1 mm depth • Automatic height adjustment • 2D + 3D measurement • Adjustable parameters for wood types Melting Unit • 8 kg tank • Independent temperature zones • Integrated piston pump for constant pressure Cooling Unit • Closed glycol-water circuit • Stable temperature control Control System • Ethernet-based communication with remote maintenance • Access to PLC, scanner, servo drives • Energy-efficient regenerative drive technology Scanner Software • Processes 3D light-section profiles • Calculates defect volume and coordinates • Unlimited product programs • Intuitive operator interface High-Pressure Injection Process 1. Melting of thermoplastic material 2. Pressure and temperature regulation 3. Targeted injection into defect 4. Immediate cooling 5. Minimal surface residue • Benefits: Kdodpfx Agjx Dmdho Uog • Low material usage • Excellent adhesion • No alteration of surrounding wood structure System Architecture • Melting unit • Heated hoses • Injection head • Cooling plate • Cooling unit with supply/return flow

Condition: excellent (used), functionality: fully functional, Universal testing machine Kjdpfxsxmv H Rs Ag Uodg for material testing / material inspection Testing of tensile strength, bond tensile strength, and shear strength of masonry & wood joints, and similar applications. - Nail pull-out test - Compression test on cement and mortar prisms - Flexural test on cement and mortar samples - Compaction test - Flexural test on wood, concrete - Shear strength test on wood - Splitting tensile strength test on wood - Scaffold connection test - Shear strength test on masonry - Tensile test on masonry - Tensile test on reinforcing steel - Tensile test on wood - Pull-out test on reinforcing steel - Reverse bending test on reinforcing steel - Dowel pull-out test - Adhesion tensile test I have made a video demonstrating the machine's operation. I can send this video to a mobile number via WhatsApp or Signal!

Condition: new, Year of construction: 2025, functionality: fully functional, Labelling machines for self-adhesive labels. Nearly all applications and speeds are possible. 6000–9000 bottles per hour are no problem. Kjdjx Dx Ncopfx Ag Usdg Depending on requirements, the machines are equipped with 1 or 2 stations for self-adhesive labels—front, back, and/or wrap-around labelling. Label width: as required Label length: as required Bottle format: any format possible Further information and additional machines available on request.

Condition: used, Year of construction: 2003, Used machine Year of manufacture: 2003 Features and technical data: - Control system with LCD display - Swiveling operator panel - Program memory - Manual pressure bridge adjustment - Feed via transport chain - Extendable workpiece support Jointing unit 1961: - 2 x 2.0 kW - Diamond jointing cutters for up-cut and down-cut operation Edge magazine 1903: - Support plate 820 mm, max. loading capacity 40 mm - Automatic feeding of coil and strip material Kdjdpfx Aowka Nysg Usg Adhesive application system 1906: - Cartridge system with sensor-controlled nozzle - Automatic reloading - Use of PUR adhesives possible Pressure unit 1816: - With powered roller - Pneumatic control of the pressure unit End trimming unit 1918: - 2 x 0.22 kW - Swivels from 0 to 10°, pneumatically adjustable Milling unit 1942 MOT 2: - For flush, radius, and chamfer milling - Motorized adjustment - Air nozzle at milling unit Corner copying unit 1832: - Corner copying up to r = 3 mm, postforming up to r = 6 mm Radius scraper unit 1929 MOT 2: - For plastic edging up to 3 mm - Chip collection box for radius scraper Surface scraper 1964: - Process-controlled surface scraper - Air nozzle at surface scraper Buffing unit 1940 Edge thickness, coil material: 3 mm Edge thickness, strip material: 5 mm Max. edge thickness, corner copying: 3 mm Workpiece thickness: 6-45 mm Workpiece thickness, corner copying: 45 mm Min. workpiece length: 180 mm Feed speed: 8 m/min Distance, workpiece support: 470 mm Support plate diameter for edge material: 800 mm End trimming blade for coil material up to: 3 mm Heating up time: 3.5 min Jointing cutter power: 2 x 2 kW End saw power: 2 x 0.22 kW Milling station power: 2 x 0.6 kW Corner copying power: 0.22 kW Extraction nozzle jointing unit: 120 mm Extraction nozzle milling unit: 70 mm Extraction nozzle scraper unit: 70 mm Dimensions: 5,350 x 1,669 x 1,940 mm Weight: 1,200 kg Location: Röllbach Availability: short notice

Condition: used, Used Kosme edible oil PET bottle filling line with capacity 3000 bottles / hour and including blow moulding equipment. Made in 2012 and with only approximately 72 hours of use. Last used on sunflower oil and suitable for bottles sized 1l (3000 BPH, press cap, hot melt label), 2l (2800 BPH, press cap, hot melt label), 5l (2000 BPH, screw cap, adhesive label) and 10l (1000 BPH, screw cap, adhesive label). Line includes the following equipment: - Kosme KSB 2XL/4F blow moulder. Preform neck dimensions: smallest neck 28mm, largest neck 48mm, neck ring diameter 53mm, neck height 22mm, max length (under neck ring) 200mm. Preform bottle dimensions: max diameter 235mm, max height 430mm, base height 55mm. - Filler / capper model Weighblock 16/1440 6/540 P. - Labeller model Extra HM 4/720 Sa1 E1. - Packer model Acepack 2/4T. - Carton erector model Formapack H. - Carton sealing unit model Sealpack H. - Palletiser and stretch film wrapper. Kdedew U A Ilopfx Ag Usg - Coders, handle applicators, elevators and conveyors. - (8) 25000 litre oil tanks, compressor, dryer, air tank, spare parts, auxiliary equipment and approximately 100,000 PET preforms.