CNC turning and milling center

MORI SEIKI NT 4200/1000S

Condition: ready for operation (used), Year of construction: 2006, operating hours: 16,093 h, functionality: fully functional, turning length: 1,000 mm, spindle speed (max.): 5,000 rpm, controller model: MITSUBISHI M-720BM (MAPPS 2), counter spindle speed (max.): 5,000 rpm, milling spindle speed (max.): 12,000 rpm, TECHNICAL DETAILS Turning length: 1,000 mm Main Spindle Max. spindle speed: 5,000 rpm Drive power: 22/15 kW Spindle bore: 73 mm Counter Spindle Max. spindle speed: 5,000 rpm Drive power: 22/15 kW Spindle bore: 73 mm Milling spindle speed: 0 - 12,000 rpm Tool holder: Capto C6 Tool stations: 100 positions Hollow clamping device: 67 mm MACHINE DETAILS Control unit: MITSUBISHI M-720BM (MAPPS 2) Operating Hours Operating hours: 26,875 h Spindle hours: 16,093 h EQUIPMENT Y-axis Fully indexable B-axis Chip conveyor, discharge right Standard coolant system Interface for high-pressure coolant system, 70 bar Tool spindle with through-spindle cooling Coolant spray gun Blow air through sub spindle Manual tool presetting on main spindle Fodpey Eydysfx Ag Ispl 3-color signal tower Double foot switch Simultaneous 5-axis machining Automatic power off Tool offset for 5-axis machining Programmable data input Dynamic interchange diameter/radius Stroke check prior to movement

Condition: used, Year of construction: 2007, travel distance X-axis: 6,000 mm, travel distance Y-axis: 2,000 mm, travel distance Z-axis: 1,250 mm, rotational speed (max.): 5,000 rpm, SPINDLE TAPER ISO 50 X LONG. TRAVEL MM.6000 Z SADDLE TRAVEL MM.1250 Fpjdpfxjwz H Rfo Ag Ijl Y VERTICAL TRAVEL MM.2000 SPINDLE SPEED RPM.5000 FEEDS MM/MIN.8000 SPINDLE MOTOR POWER KW. 37 CNC HEIDENHAIN iTNC 530 REMOTE HAND WEEL FLOOR PLATES 7000x2000- 15 TON/MQ. TABLE 1080 X 7220 X H 820 MM ATC.40 CHIP CONVEYOR ROTATING HEAD IN CONTINUOUS TUPC 0,001°x0,001° COOLANT THROUGH THE SPINDLE 20bar FUNCTION RTCP FPT AUTOCAL EXTERNAL COOLANT TANK HEIGH & LOW PRESSURE WITH PAPER FILTER N.2 AUTOMATIC HORIZONTAL DIVIDERS WITH 2 SUPPORT TABLES N.1 PIECE PROBE

Condition: excellent (used), Year of construction: 1995, Maximum center height: 330 mm Maximum distance between centers: 2000 mm Working area: Max. turning diameter over bed cover: 650 mm Max. turning diameter over cross slide: 360 mm Main spindle: Spindle diameter at front bearing: 140 mm Spindle bore: 107 mm Main drive: 58.5 kW 2-stage speed range: 4 – 750 rpm / 750 – 3060 rpm Feed drive: Rapid traverse rate X/Z axis: 10/10 m/min Turret: Number of tool positions: 12 Of which, driven tool positions: 6 Cylindrical shank tool holder: VDI 50 mm Dimensions / Weight: Footprint L x W x H: approx. 6400 x 2150 x 2000 mm Weight: 9400 kg Accessories / Special features: • CNC control system HEIDENHAIN TurnPlus EP 90 with color screen • Spindle orientation C-axis • 12-position turret, VDI 50, of which 6 positions with driven tools, manufacturer SAUTER DIN 5482 B 20x17, max. speed 3000 rpm. • Hydraulic 3-jaw chuck Ø 315 mm with various clamping jaws • Hydraulic steady rest with follower device • Hydraulic quill actuation • Air extraction system, manufacturer LTA • Various tool holders VDI 50 • CE compliant Fjdjx Sx Htepfx Ag Iopl In 08/2025, GILDEMEISTER Service replaced the following parts: 1 servo motor, 1 AC servocontroller inverter power module for 2 axes, 1 power module Simodrive, 1 rectifier/inverter module, 1 control unit for 1 axis, 1 control module for 2 axes inverter servo drive, 1 Simodrive power module (1-axis motor) Total repair costs: 17,000.00 EUR net Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel

Condition: ready for operation (used), Year of construction: 2014, operating hours: 48,973 h, controller manufacturer: SIEMENS, controller model: 840 D, number of axes: 3, This DMG MORI CTX Beta 800 4a was manufactured in 2014. It features a Siemens 840 D control system, a counter spindle, and a bar machine package for enhanced versatility. The machine includes a 980-liter coolant system and a hinge type conveyor for efficient operation. If you are looking to get high-quality turning and milling capabilities, consider the DMG MORI CTX Beta 800 4a machine we have for sale. Located in Germany, contact us for more information about this machine. • 2 x 16 fold Sauter star VID 30 • Siemens 840 D • Excentric turning and milling operation Fjdsx D Nd Dspfx Ag Ijpl • TC alternating speed • Counter spindle • Glass scales Y1, Z1, Z2, Z3, X1, X2, X3 Additional equipment • 980 liter coolant with 8 bar/20 L and 20 bar/40 L programmed by M function • Pater band filter • Chuck rinsing device for main outside • Chuck rinsing device for counter outside • Coolant spray gun • Hinge type conveyor • Bar machine package • Window cleaning with compressed air • SK package for alu machining • Tool breakage Artis CTM

Year of construction: 2024, condition: new, Motorized sheet metal shear Technical data Cutting capacity: 2.5 mm Cutting length: 2550 mm Cutting angle: 1°40′ Fjdjhk Nf Repfx Ag Ispl Stroke rate/min: 35 1/sec Motor power: 3 kW Back gauge range: 550 mm Table width: 400 mm Table height: 850 mm Height: 1260 mm Width: 1350 mm Length: 3100 mm Weight approx.: 1540 kg

Condition: excellent (used), Year of construction: 2022, operating hours: 4,605 h, functionality: fully functional, Controller: FANUC 31i-B5 Max. turning diameter: ø540 mm Max. turning length: 1.020 mm Spindle bore / bar capacity: ø76 / 65 mm Y-axis travel: 170 mm (±85) Milling spindle: 12.000 rpm, 18.5 kW Fsdpfezilupox Ag Iopl Tool magazine (ATC): 80 stations, Capto C6 Tool change time: 2.0 s Counter spindle: 5.000 rpm, 22 kW Spindle power: 22 / 18.5 kW (S1/S6)

Condition: good (used), Year of construction: 1980, turning diameter over bed slide: 1,040 mm, turning diameter over top slide: 710 mm, turning length: 2,000 mm, bed width: 600 mm, Optional chuck 1200 mm 2 Axis RSF Digital read out Conical turning attachment Spindle bore 130 mm Central lubrication DBC Turning Length: 2000mm Swing over bed Ø: 1040mm Swing over cross slide Ø:710mm Swing in the gap Ø: 1780mm Gap length: 1000mm Spindle bore: 130mm Bed width: 600mm Tailstock spindle Ø: 130Ø Stroke pinole: 300mm Fpedpfx Agox Tgr Ts Iel Spindle taper: 6Mk Power: 22kW Speeds / ranges: 600Rpm Feed rate X-Axis: 4000mm/min. Feed rate Z-Axis: 4000mm/min. Length: 6000mm Width: 2100mm Height: 2100mm Weight: 8300kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: excellent (used), Year of construction: 2007, functionality: fully functional, total height: 9,350 mm, total width: 3,980 mm, total length: 3,074 mm, load capacity per storage section: 380 kg, input voltage: 400 V, 3 pieces in stock Automated warehouse optimization storage system KARDEX Shuttle XP500 System Type : SHUTTLE-XP-500-3650x864 Control : C3000, with B/W OP3000 display Serial No. : 06009822 Year of construction: 2006 Load per tray: MediumX: 380 kg (proportionally distributed) Tray dimensions: 3650 x 864 mm Number of trays: 48 pieces (more on request) Dimensions Shuttle W x D x H: 3980 x 3074 x 9350 mm (height Kardex is adjustable to available height) Power: 3/N/PE400 V, 17 A, 50/60 HZ, 8.6 kVA This offer is valid provided system is unsold Technical details each Shuttle: - Maximum total capacity of the KARDEX Shuttle XP: 2 x 32,700 kg - Maximum tray capacity: 48 trays: 380 kg each, evenly distributed, More trays can be ordered. - Tray dimensions: 3650 x 864 mm - Machine dimensions: Wide x Depth x Height: 3980 x 3074 x 9350 mm - Footprint of the system appx: 12.23 m2 - Capacity with 48 trays: appx. 151 m2, every tray is appx. 3.15 m2 - Electronic volume measuring system in 25 mm screen (grid) - An access opening with sliding doors to protect people and stored goods - Control C3000, with B/W OP3000 display - LED Anti-dazzle lighting above access point - Use of toothed-belt for minimum noise - Use of toothed-belt for fastest order picking Price: On request only by e-mail Price: excl. VAT, including transport, assembly and warranty Delivery time: from stock Fedpfswgyxtox Ag Ijpl Machinehandel De Leeuw BV is one of the few companies in Europe that trades and has in stock mainly used Kardex Remstar VLM automatic Lift & rotating warehouse systems. See our website for the current stock. We assemble and/or disassemble these systems in a safe manner with VCA certified technicians and we have been doing this for more than 30 years. We also dismantle other brands such as: Hänel, Electrolux, Bertello, Megamat, Lista, Denocard Machinehandel De Leeuw BV Oordeelsestraat 7 – b 5111 PA Baarle-Nassau The Netherlands

Condition: good (used), Year of construction: 2003, functionality: fully functional, input voltage: 400 V, travel distance X-axis: 780 mm, travel distance Y-axis: 560 mm, travel distance Z-axis: 560 mm, workpiece weight (max.): 4,000 kg, number of slots in tool magazine: 120, controller manufacturer: Heidenhain, total height: 2,800 mm, total length: 6,000 mm, total width: 6,000 mm, overall weight: 12,000 kg, table length: 630 mm, table width: 500 mm, controller model: iTNC530, nominal power (apparent): 61 kVA, rapid traverse Z-axis: 50 m/min, rapid traverse X-axis: 50 m/min, rapid traverse Y-axis: 50 m/min, spindle speed (max.): 18,000 rpm, spindle speed (min.): 20 rpm, table load: 4,000 kg, operating hours of spindle: 19,500 h, Equipment: chip conveyor, rotational speed infinitely variable, DMG DMC 60T RS3 with Heidenhain iTNC 530, no maintenance backlog, in good condition. Ideal machine for unmanned operation, geometrically within new-machine tolerance. The machine can be inspected and measured on site by arrangement. Machine Data: Machine description: Machining centre with pallet storage Manufacturer: DMG MORI Model: DMC 60T RS3 Year of manufacture: 2005 Condition: good Equipment: - Direct linear measurement in X/Y/Z (glass scales) - Chip conveyor - High-pressure coolant system 40 bar (IKZ) - Extraction unit - NC rotary table - Tool magazine, 120 positions - Heidenhain measuring probe - Rotating viewing window - High-pressure coolant 40 bar - Signal lamp - Chip flushing - Operating mode 4 Technical Data: Number of axes: 5-axis Control: Heidenhain iTNC 530 NC rotary table clamping surface: 500 mm x 630 mm Weight: approx. 9,000 kg Chip conveyor: Yes Fodpfx Agorxrklj Iepl Coolant system: Yes Internal coolant supply: Yes Travels and axes: X-axis: 780 mm Y-axis: 560 mm Z-axis: 560 mm C-axis: 360° B-axis: -90°/+12° Feed rates and rapid traverse: X-axis: 50 m/min Y-axis: 50 m/min Z-axis: 50 m/min B-axis: - C-axis: 30 m/min Motor spindle: Max. speed: 18,000 rpm Spindle taper: HSK A63 Tool changer: Automatic tool changer: Yes Number of magazine positions: 120 Pallet changer: 5 pallets

Condition: excellent (used), Year of construction: 2007, Universal Milling Machine, gear type, feed range X/Y/Z 500/350/400 mm, table size 800x400 mm, rotary / tilting table 600x300 mm, motor 3 KW, 18 speeds 40-2000 rpm., ISO 40, quill travel 60 mm, boring capacity Ø 40 mm, digital readout on 3 axis, automatic and rapid feeds, horizontal milling head, collant systen, halogen lamp, + round- / tilting table, dimensions 1500x1700x1750 mm, weight ca. 2200 kg; ex demonstration machine Fpodpfx Agsfvci Ee Isl