Machining Center - Vertical

Microcut VM 1000

Condition: used, Year of construction: 2005, - Fagor 8055 CNC control - Additional tank for internal spindle cooling (15 bar) 400 liters - Year of construction 2005 Technical data: - Travel X/Y/Z: 610 / 455 / 520 mm - Rapid traverse: 24 m/min - Working spindle speed: 8000 rpm - Tool holder: BT40 - Table size: 762 x 363 mm - Maximum table load: 350 kg - Motor power: 18 kW - Operating voltage: 400 V Tedpfx Aotvf Htoc Tsb - Weight: 3140 kg

Condition: used, TURNING CENTER "MORI SEIKI" MOD. ZL 200SMC With twin powered turret and sub-spindle CNC MSC-501 Turning length: 452 mm Max. turning diameter: 388 mm Max. diameter over bed: 510 mm Distance between centers: 751 mm Spindle mount: A2-6 Spindle speed: 4,000 rpm Spindle motor power: 11 kW Number of tools: 12 Tjdpfexwxwtex Ac Tob

Year of construction: 2002, condition: good (used), Make: Matsuura Type: LX-O Control: YASNAC Year: 2002 Specifications Metric US Standard X - Travel 330 mm Y - Travel 300 mm Z - Travel 250 mm Table Length 540 mm Table Width 320 mm Table load 100 Feed rate X-Axis 90000 mm/min. Feed rate Y-Axis 90000 mm/min. Feed rate Z-Axis 90000 mm/min. Spindle Taper 30 ISO/Bt/Mk Power on spindle 7.5 kW Speeds / ranges 40000 Rpm ATC / revolver 30 Todpfslz Rvlox Ac Tob Chip conveyor Yes Dimensions (Estimate) Length 2800 mm Width 2600 mm Height 28000 mm Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Year of construction: 1990, condition: like new (used), Used Schuler hydraulic press for sale Brand : Schuler Schuler EB 2-500- 2.75-0.85 H-frame hydraulic press Power ( ton ) : 500 tons Todpfxshcnxre Ac Tjb Table dimensions ( x-y/mm) : 3000×1800 Slide dimensions ( x-y/mm) : 3000×1800 Stroke ( x/mm) : 850 Stroke per minute from 12 to 24 Control Siemens S7 New hydraulic presses for sale

Condition: excellent (used), Year of construction: 2015, Traverses XYZ: 1020 x 540 x 510mm, table size 1200 x 540mm, ISO40 spindle taper, Tjdpfxsylbpve Ac Tob spindle speed 12000 rpm, Siemens 828D Control, spindle motor power 15kW, 30 station ATC with side arm, Through Spindle Coolant, Low Volt Light, Swarf conveyor

Condition: excellent (used), bore depth 500 mm spindle speed: 1 Tjdexx A D Tepfx Ac Tjb

Condition: new, maximum load weight: 67,200 kg, overall weight: 85,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpts from the equipment. Full specifications available upon request. GOOSENECK Todpsrgzv Nefx Ac Tjb * Gooseneck in SNT design to optimize load floor length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractors: 6 x 2, 6 x 4, and short 8 x 4 * Detachable steel front wall, approx. 400 mm high * 3 kW electro-hydraulic power unit for controlling hydraulic functions, except for hydraulic winches * Outer beams of the gooseneck with mounting holes for bolt-on lashing rings * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of flat lashing rings at the rear of the gooseneck (LC 10,000 daN) * 1 pair of plug-in aluminum side boards, approx. 400 mm high, anodized * 1 plug-in aluminum rear board, approx. 400 mm high, anodized * Approx. 40 mm thick hardwood flooring above gooseneck, checker plate flooring above kingpin * 3.5 inch kingpin * Gooseneck guide plate for the fifth wheel plate, approx. 500 mm wide * Round NATO socket at the front connection strip (Maeler & Kaege VG 96 917) * In addition to the electro-hydraulic unit, a truck hydraulic connection with flow regulator, including bracket for hanging supply lines (Faymonville couplers) * 2 pairs of stake pockets recessed in the gooseneck, for plug-in stakes approx. 100 x 50 mm LOAD FLOOR * Extendable load floor, approx. 11,000 mm long, with rear bevel approx. 500 mm x 10° * Pneumatic locking with conical locking bolts and reinforced locking positions; supply lines are protected inside the extendable beams and automatically adjust to the respective deck length * BPW axles and suspension, 1st axle steered, 2nd axle fixed, all other axles hydro-mechanically forced steered * 1st axle with electro-magnetic reverse lock via reverse gear and manual activation * Axle load capacity: 12,000 kg each * Air suspension with lift and lower valve * 235/75 R 17.5 3PMSF twin tires * Mechanical landing gears with 2-speed gearbox and crank. JOST Modul B – static test load = approx. 50,000 kg * Continuous and, between axles, interrupted approx. 50 mm thick hardwood floor on load deck (increases coefficient of friction) * Slotted holes for attachable and repositionable bridging elements: – at the fixed part behind the gooseneck – on the front of the load floor * 1 sliding intermediate table, approx. 500 mm wide, for the sliding tube with large cross-section, checker plate flooring, front and rear with slotted holes for attachable and repositionable bridging elements * 1 pair of recessed flat lashing rings in the front fixed part of the load floor (LC 10,000 daN) * 9 pairs of recessed lashing rings, foldable outward, in the load floor perimeter frame (LC 10,000 daN) * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking control, no installation required in the tractor * 1st axle with automatic lift axle function and start-up assist according to EU Regulation 2021/535 * Under the gooseneck and at the rear cross member, left and right, a 7-pin socket each with holder for warning signs * Factory-applied sand coating on the perimeter frame of the load floor as well as the checker plates and the transition area between load decks

Condition: new, Year of construction: 2025, Yanigav Earth Auger TAM 245 • Simple three-point hitch • Very robust, welded chassis • Versatile, high-performance gearbox from 30 to 90 HP • Usable auger diameters from 10 cm to 80 cm and up to 1.80 m in height • Offset of 1.30 m on each side of the axis Tsdpfx Acer Eznij Tob • Chassis length: 245 cm • Auger tilt adjustment (front/back and right/left) • Auger not included

Condition: refurbished (used), Year of construction: 2003, functionality: fully functional, turning diameter over cross slide: 510 mm, turning length: 752 mm, turning diameter: 390 mm, spindle speed (max.): 4,000 rpm, rapid traverse X-axis: 18,000 m/min, rapid traverse Y-axis: 24,000 m/min, rapid traverse Z-axis: 24,000 m/min, feed rate X-axis: 18,000 m/min, feed rate Z-axis: 24,000 m/min, CNC Lathe MORI SEIKI ZL-2035MC – Technical Data Sheet The MORI SEIKI ZL-2035MC is a high-precision CNC lathe, ideal for advanced multi-axis turning operations, featuring dual spindles and live tool turrets. Manufactured in December 2002, it is engineered to deliver productivity and accuracy in complex machining processes. General Specifications Brand: MORI SEIKI Model: ZL-2035MC Category: CNC Lathe Year of construction: 12/2002 CNC Control: MORI SEIKI MSG-501 Machine weight: 5,900 kg Machine Dimensions: Length: 4,350 mm Width: 2,400 mm Height: 2,200 mm Machining Capacities Max swing over bed: Ø 680 mm Max swing over carriage: Ø 510 mm Distance between centers: 752 mm Max turning diameter: Spindle No. 1: Ø 390 mm Spindle No. 2: Ø 294 mm Max turning length: 520 mm Bar capacity: Ø 65 mm (Ø 51 mm on No. 2) Axis Travels X Axis: No. 1: 235 mm No. 2: 175 mm Z Axis: No. 1: 520 mm No. 2: 490 mm B Axis: 505 mm Tsdpfxjxd Td Uj Ac Tsb Main Spindle Speed: 40 – 4,000 rpm Spindle nose: JIS A2-6 Chuck diameter: Ø 210 mm Minimum programmable C axis angle: 0.001° Spindle motor power (continuous/30 min): 11 / 7.5 kW Sub-Spindle Speed: 40 – 4,000 rpm Spindle nose: JIS A2-5 Chuck diameter: Ø 160 mm Minimum programmable C axis angle: 0.001° Spindle motor power (continuous/30 min): 7.5 / 5.5 kW Tool Turrets Turret No. 1 Number of stations: 12 Driven stations: Yes Driven tool speed: 4,000 rpm Turning/boring tool dimensions: 25x25 mm / Ø 32 mm Turret No. 2 Number of stations: 8 Driven stations: Yes Driven tool speed: 3,000 rpm Turning/boring tool dimensions: 25x25 mm / Ø 32 mm Rapid Feeds X axis rapid traverse: 18,000 mm/min Z axis rapid traverse: 24,000 mm/min B axis rapid traverse: 24,000 mm/min Manual feed for X / Z / B axes: 0 – 1,260 mm/min Included Accessories 5 live tool holders and various fixed toolholders Chip conveyor Transformer Part unloading arm Coolant tank with pumps Manuals, electrical diagrams, and CE Declaration

Condition: ready for operation (used), A Mori Seiki CNC lathe is available. Swing diameter over bed/slide: 450mm/300mm, max. turning diameter: 160mm, turning length: 525mm, travel X/Z: 135mm/560mm, bar capacity: 42mm, spindle bore: 52mm, spindle nose: JIS A2-5, spindle speed: 5000rpm, power: 7.5kW, torque: 172Nm, tool stations: 12, tailstock taper: MK4, quill diameter: 75mm, quill stroke: 80mm, rapid traverse: 12m/min. Machine dimensions X/Y/Z: approx. 2500mm/1500mm/1700mm, weight: approx. 3250kg, control: Fanuc Series 15-T. Documentation available. An on-site inspection is possible. Tsdpfx Ajzipf Soc Tsb