Eccentric Press - Single Column

Maskinexport nicht bekannt

Year of construction: 1990, condition: used, pressure 75 t throat 300 mm stroke 8 - 110 mm table surface area 750 x 600 mm ram adjustment 75 mm ram surface 430 x 230 mm hole in the table 250 x 150 mm tool hole in ram 40 mm no. of strokes 60 + 90 Hub/min weight of the machine ca. 4,4 t total power requirement 4,5 - 6,8 kW dimensions of the machine ca. 1,95 x 1,1 x 2,35 m distance table/ram Hub unten, Stöß. unten 19 mm distance table/ram Hub oben, Stöß. oben 380 mm Furnishing: Chsdpfx Absd Nl E Usbof - with hydraulic clutch-brake combination, with new hydraulics and oil cooler - with gear transmission in oil bath - fixed table prepared for the attachment of tool changing consoles - 2 roller bars in the table - mechanical overload in the ram The following work is carried out on the machine / partial overhaul: - Machine is completely disassembled, checked, seals changed, defective parts exchanged etc - Machine is repainted - new Balluff cam control - new hydraulic unit with oil cooler for the clutch - new Vogel central lubrication - new control cabinet with touch panel and ABB safety control - Current UVV test with braking time measurement

Condition: ready for operation (used), Year of construction: 1970, LZ-Lathe KERN Type:DS 20 AL Year 1970 with 3 jaws lathe chuck Forkardt 250mm, tool quick winder holder Multifix size C with holders coolant device. turning diameter overbed:500mm turning diameter overplane : 250mm centre distance : 1000mm spindle speed: 12 -1200U/min Csdpfogqxciox Abbehf Machine can be demonstrated under current Good guides .

Condition: good (used), Year of construction: 1970, grinding diameter: 1,200 mm, grinding length: 5,000 mm, Accurite digital readout Chuck diameter 900 mm Crank shaft head counter balance weight 2 x 4 different sizes  4 x steady rest dressing device  6 segment stone up to 1500 mm diameter In feed stone 0,0025 - 0,050 mm Codpewrxqxefx Abbehf Table feed rate 50 - 3975 mm/Min Coolant & Filtration system Centre height: 600mm Grinding Ø: 1200mm Grinding length: 5000mm Grinding stone dimensions:1600 x 100mm Grinding stone speeds: 1620Rpm Length: 17500mm Width: 5500mm Height: 2200mm Weight: 60000kg

Condition: used, Year of construction: 2007, Bending length 3050 mm Max. prebending capacity 13 mm Max. rolling capacity 16 mm Top roll dia. 340 mm Lower roll dia. 340 mm Side rolls dia. 240 mm 4-rolls Fully hydraulic Hydraulic drop end Digital read out of roll positions Equipped with: Top support Chjdpexhgqiofx Abbjf Side support

Condition: good (used), turning diameter: 5,000 mm, travel distance Z-axis: 2,000 mm, turning length: 2,500 mm, The machine is in good technical condition, fully functional, modernized in 2008. It is equipped with a Siemens Sinumerik 802 D control system, a maximum turning diameter of 5000 mm and a clamping plate diameter of 2500 mm. The workpiece weight is 40 tons and the height is 2000 mm. Chodpev Dkykefx Abbof

Year of construction: 1965, condition: used, pressure 150 t throat 550 mm stroke 10 - 140 mm table surface area 1180 x 980 mm no. of strokes 40 Hub/min dayligth 500 mm ram surface 1040 x 800 mm ram adjustment 70 - 150 mm tool shank hole (depth x diameter) 435 x 55 mm required power 15 kW weight of the machine ca. 12 t dimensions of the machine ca. 3 x 1,7 x 3 m Cedocubatopfx Abbjhf - with additional brake - slide weight compensation - motorized slide adjustment - central grease lubrication (manual) - table mounting plate - safe for manual inlay work

Condition: used, Year of construction: 1995, turning diameter over bed slide: 500 mm, Universal lathe Make: ZMM Type 500 Year: 1995 Technical Data Manufacturer: ZMM Sliven Model: Universal 500 Year of manufacture: 1995 Centre distance: 1000 mm Swing over bed ø: 500 mm Spindle bore: 73 mm Dimensions (L x W x H): 2.7 x 1.2 x 1.8 m Weight approx.: 3100 kg Equipment Codpfswudhuox Abbjhf • 3-jaw chuck Röhm ZS 350 mm • Quick-change toolpost • Live center • Coolant pump • Machine lamp All information subject to change. A live demonstration under power is possible at any time in our showroom.

Condition: used, Year of construction: 1970, machine/vehicle number: 120895, pressure:63 t throat:250 mm stroke:8 - 100 mm no. of strokes:120 Hub/min table::715 x 500 mm dayligth:330 mm ram adjustment:63 mm clamping plate:700 x 480 mm hole in the table:240 mm Chodpsfx Hv Hjfx Abbof Hole in clamping plate:110 mm dimension of ram:450 x 280 mm weight of the machine ca.:5,5 t dimensions of the machine ca.:1,2 x 1,7 x 2,7 m hydraulic tilting single column eccentric press, tilting in 4 steps, opening to rear (325 x 500mm) and below (360x160mm) with central lubrication via hand pump, additional clamping plate 700 x 480 x 850 mm, two-hand operation, foot-trip operation possible, operating-mode selector for adjustment of continuous or single stroke, emergency cut-off, piece counter, various accessories

Condition: used, Year of construction: 1999, Technical details: x-travel: 3 500 mm y-travel: 2 200 mm z-travel: 1 200 mm c-axis: +/- 200° control: Heidenhain TNC 426 spindle rpm - counter clockwise:: max. 10000 spindle rpm - clockwise:: max. 10000 distance between columns: 2 500 mm distance spindle /table: vertical: 1230 mm clamping surface area: Tisch: 3000 x 2000 mm table load: 10 t tool taper: HSK A 63 feed:: X/Y/Z: max. 20 m/min. compressed air: 8 bar total power requirement: ca. 100 kW weight of the machine ca.: 40 000 kg dimensions of machine: 18,0 x 6,0 x 5,8 m Chsdsu Nc Emjpfx Abbof 5 axis Portal Milling Machine 5-axis portal milling machine Milling spindle: make Hauser type HS 256A-01 Uni, speed max. 10.000 rpm. direct drive Milling head: make Hamül, fork type, A-axis integrated = angle of rotation +/- 110°. Tool changer: Hamül make, rotary indexing table type with rotary table, for 32 tool positions chip conveyor: 2 pieces hinged belt conveyor make DGS with water tank, insertion length 8.500mm make BKW type DL 55V-2KK, capacity 2,41 l/min.; (combined for oil- water mixture for oil and spindle cooling) Cooling lubricant system: belt filter make DGS type SBF 150 Operation: via control panel type Heidenhain LE 426 X-, Y- and Z-axis with Heidenhain measuring rods. manual control unit HR 410 hydraulic counterbalance (Z-axis) Equipment: Enclosure (protective walls with viewing windows and protective doors) hydraulic system working area lighting *

Year of construction: 1981, condition: ready for operation (used), Working width: 2500mm, max. sheet thickness: 20mm, lateral cylinder support device with three adjustable support rollers and conical bending device, machine provided for exchangeable top rollers up to min. Ø 450mm, machine revision 2009, factory inspection 2012. Cedsnvfdbopfx Abbshf