CNC machining center

MAKA D 400 d

Condition: used, Painting system consisting of: Pos.1 Venjakob belt conveyor - Manufacturer: Venjakob - Working width: 1,300 mm - Length: 3,000 mm - Feed adjustable via handwheel ~ 2.5 – 7.5 m/min - Volt, Hz: 400 / 50 - Colour RAL 7035 Pos.2 Cefla dust extraction machine - Manufacturer: Sorbini - Type: VS/32-E - Year of manufacture: 1998 - Working width: 1,300 mm - Working height: 900 mm + - 20 mm - Operating side: right - Roller conveyor - Air blowing channel, above 2 pcs. - Air blowing channel, below 1 pc. - Dust remover brush - With ionisation bar from above - With ionisation bar from below - With own drive - With own control - Length ~ 910 mm - Width ~ 2,600 mm - Weight 1,260 kg - Extraction nozzle D 180 + 120 mm - Total connection 7.6 kW - Volt, Hz 400/ 50 Pos.3 Venjakob VEN SRAY Perfect automatic spraying machine - Manufacturer Venjakob - Type. VEN SPRAY PERFECT - Year of construction 2013 Gbsdpfx Aaev I Akvoxol - Working width 1,300 mm - Working height 940 + - 20 mm - Operating side left - IR preheating, number of radiators 2 pcs. - Duo-design spray gun drive - Dry suction - Diameter of suction nozzle 600 mm - Exhaust air capacity 10,000 m³/h - Belt transport system - feed speed infinitely variable ~ 4-10 m/min - conveyor belt cleaning system - paint recovery via V-belt system - gun control, EPS-CNC CNC 7000 - colour management system for number of pumps 3+1 pcs. - number of installed airless spray guns 4 pcs. - Quick-change system for spray guns - Remote maintenance system - Dust cover on the outlet side of the machine - Exhaust air recirculation system - Exhaust air control of the suction ventilator - Machine suitable for water-based paints - Machine suitable for solvent-based paints - Length 5,509 mm - Width 4,500 mm + 2,400 mm - Height 3,380 mm + 510 mm - Total connection ~ 20 - 26 kW - Volt, Hz 400/50 - Colour RAL 7035 - Kremlin AVX AirMix spray guns - Small parts container - gun support arm system for quick removal of 4 AirMix spray guns from the spray booth, including quick couplings for pneumatics and material hoses. Pos.4 Venjakob belt conveyor - manufactured by Venjakob - working width 1,300 mm - length 2,000 mm - feed adjustable via handwheel ~ 2.5 – 7.5 m/min - Volt, Hz 400 / 50 - Colour RAL 7035 Pos.5 Cefla pallet dryer - Manufacturer Cefla - Type VN 2000/5500/190.5/30 - Year of construction 2003 - Working width 1,300 mm - Number of pallets 30 pcs. - Pallet length 5,600 mm - Usable pallet length 5,300 mm - Load capacity per pallet 300 kg - Max. part height ~ 110 mm - Clearance between pallets 120 mm - Dimension: centre of pallet to centre of pallet 3,658 mm - Max. part length ~ 5,200 mm - Number of controllable temperature zones 2 pcs. - Supply air flow rate 6,000 m³/h - Exhaust air flow rate 6,000 m³/h - Heat output max. 175 kW - Max. drying temperature ~ 55 - 60 degrees - With heat exchanger, hot water - Without hot water control valves - U-shaped flow direction - Inlet side on the right - Feed speed via frequency converter control ~ 2-20 m/min - Suitable for water-based paints - Suitable for solvent-based paints - Length 7,820 mm mm - Width 6,130 mm - Height 3,905 mm - Total connection ~ 23 kW - Volt, Hz 400 / 50 - Voltage fluctuations max. +/- 5 % - Without control valves and water pumps Pos.6 Cefla belt conveyor - Manufacturer Cefla - working width 1.300 mm - length 2.000 mm - feed adjustable via handwheel ~ 2.5 – 7.5 m/min - volts, Hz 400 / 50 - colour RAL 7035

Condition: used, machine/vehicle number: 007687, Type of edging: Thin edge, Thick edge, Solid wood Gluing System: EVA Hotmelt, Hot Air Gbsdpfx Aaswuz Npoxol Premilling Unit: yes Corner Rounding Unit: yes Max feed speed: 18 m/min Maximum panel thickness: 60 mm Operating Units: 7 nr

Condition: used, machine/vehicle number: 006370, Type of edging: Thin edge, Thick edge Gbodpfxsl Txw Hj Aaxel Gluing System: EVA Hotmelt Premilling Unit: yes Corner Rounding Unit: yes Grooving Unit: yes Max feed speed: 25 m/min Maximum panel thickness: 60 mm Operating Units: 12 nr

Condition: used, Year of construction: 1989, Used machine Year of manufacture: 1989 Gbsdew I U E Aspfx Aaxol Condition: Function tested Equipment and technical data: Max. edge thickness: 20 mm Max. edge height: 51 mm Max. thickness of coil material: 3 mm Min. workpiece length: 140 mm Min. workpiece width: 60 mm Glue system: 1906 cartridge Pressure unit Milling unit 1920 for flush milling up to 20 mm and chamfer milling Required space (LxWxH): 3150x1800x1375 mm Weight approx.: 800 kg Location: Flörsheim Availability: Short-term

Condition: used, Year of construction: 2011, Base Machine M800 X5 TV 1 WORKING RANGE X: 5,020 mm Y: 1,830 mm Z: 675 mm Clearance Height: 300 mm (from 50 mm suction cup height) MACHINE STRUCTURE The base structure is a monolithic construction made from thick-walled steel. It is reinforced across the entire machine bed with welded components, providing exceptional stability. The table design, with its large base, is the key to ensuring lasting precision and stability. The machine’s layout enables the operator to achieve optimal workflow with minimal space requirements. The mobile gantry is built as a solid monoblock. It is positioned in the X direction on prismatic, ground guides with recirculating ball carriages. The machining unit is mounted on this mobile support carriage, also on prismatic, ground guides and recirculating ball carriages. AXIS MOVEMENT All axes travel on prismatic linear guides with large cross-section and recirculating ball shoes with a wide contact surface, which ensures optimal sliding, even at high speeds and accelerations. The precise and fast positioning of the movable gantry (X-axis) is achieved via helical rack and pinion. Large cross-section recirculating ball screws ensure accurate positioning of the machining unit along the movable gantry (Y and Z axes). The perfect mechanical dynamics and maximum positioning accuracy are controlled by high-quality drives and brushless motors. Max. axis speeds: · X-axis = 90 m/min · Y-axis = 90 m/min · Z-axis = 30 m/min Safety device with bumper and light barrier 1 Bumpers with sensors are fitted to the movable upright, and a light barrier system is installed at the front of the machine. If the operator enters the active zone, the X-axis travel speed is reduced to a lower value of 25 m/min without stopping the machine. This system allows parts to be loaded during pendulum operation without the limitation of access areas, as seen with pressure mat systems. This prevents unwanted interruptions in the machining cycle and offers greater freedom of movement around the worktable. CE certification for the safety system 1 Safety protection fence 1 Side and rear protection fence Automatic central lubrication controlled via CNC 1 The lubrication of the X, Y, and Z axes is controlled by the CNC; intervals are regulated automatically, without manual intervention. Central extraction connector 1 All individual extraction connections of the machining units are collected into a central extraction port. Inside the port, there are various slider valves controlled by the NC. This reduces the required extraction air volume. Chip conveyor 1 Maxi – 5-axis electrospindle 11 kW HSK-63 “Prisma K 1 5-axis electrospindle, 11 kW at 20,000 rpm S1 (100% duty cycle) Speed: max. 20,000 rpm Rotation direction: left/right Liquid cooling Tool interface HSK 63F Inverter 18 kW, stepless, smooth power delivery Max. rotation B-axis = 200° (+-100°) C-axis = 650° Thanks to the non-orthogonal axes, it is possible to perform complex horizontal positioning in a small workspace. This enables the machining of complex geometries without the risk of collision. Gbsdpfx Aoxy Tmnsaxjl

Condition: new, Year of construction: 2026, functionality: fully functional, machine/vehicle number: SÇ 901 S Pnömatik Alüminyum Köşe Presi Makinası, - Conforms to CE standards - Corner press machine designed for 90 degree joining of aluminum profiles - 2 top presses and blade movement is pneumatic - There is a mm ruler system for the height and advancement of the blades. - Centering miter wedge is automatic - Drain button available for fine adjustment - Pneumatic presses use 2 pedals to squeeze the profile Gbsdpfx Asrbiv Ajaxjl - Profile surfaces are polyamide sheet to prevent damage - Side support arms available

Condition: excellent (used), Year of construction: 2017, functionality: fully functional, cutting height (max.): 90 mm, cutting width (max.): 3,800 mm, saw blade diameter: 380 mm, overall weight: 4,400 kg, cutting length (max.): 3,800 mm, main saw diameter: 380 mm, Beamsaw SIGMA IMPACT 90 (SCM Group) suitable for furniture panels precize cutting by one or more panels overlapped. Manufacturer: SCM Group Model: Sigma Impact 90 Production year: 2017 Cutting width: 3.800 mm Cutting depth: 3.200 mm Max. cutting height: 90 mm Front tables (air cushion): 1x 2.500x600mm, 3x 2.500x600mm Machine basement with air-cushion. Max. main blade diameter: 380 mm Scorer diameter: max. 300 mm PUSHER: brushless motor, max. speed 120 m/min ! SAW CARRIAGE: brushless motor, max. speed 150 m/min ! THK linear guides for the saw carriage movement. THK linear guides for the PUSHER movement. Automatic centralized lubrication of THK linear guides. Hi-Tronic kit: - main motor 15 kW (mode S6) - vertical movement of main and scoring blade by price ball-screws - optimized stroke of the main blade - electronic scorer adjustment in 2 axis (vertical, horizontal) - grooving with the main blade (electronic depth adjustment) - postforming cuts - window cut outs (blind cuts) - AKE flange for main and scoring blade Quantity of clamps (grippers): 10 pcs (maximum) Automatic exclusion of the clamp acting on the panels edge (up to 800 mm width). Start/stop pedal. Label printer. Control SW: WINCUT Optimalisation program: OTTIMO PERFECT CUT TOP (1x HW key) Gjdpox Nc Ayjfx Aaxjbl Control PC Eye-S: Windows + LCD touch screen 21" Air conditioning device for the electric box. Panel´s dimension automatic measuring. Laser line for the visualisation of the cutting line. Automatic double side aligner - motorized (60-2.200 mm). Machine stat: fully working Possibility to see in actuall production. Availability: cca April 2026

Condition: used, machine/vehicle number: 008319, X axis working area: 6380 mm Gsdpfx Ajx A Tc Ijaxjbl Y axis working area: 1380 mm Working Table: Pod and Rail Main Electrospindle power: 11 KW Number of controlled axes: 5 axes Total number of tool changer positions: 32

Condition: used, Year of construction: 2017, Table dimensions: 2700 x 900 mm HSK 63 F interface 2x spindles for HSK 63 F interface (30 + 40 mm) Spindle tilt: -45° to +45° Usable spindle length: 180 mm Right and left-hand rotation 4-roller feed with motorized height/width adjustment and pneumatic clamping 7.5 kW brake motor with electronic inverter CNC adjustment for: - spindle tilt - spindle height adjustment - complete fence - front part of the fence - table positioning in front of the spindle - electronically variable speed control 1,000 - 10,000 rpm - Aigner milling fence with aluminum jaws - Touchscreen with graphic function - Windows operating system - Camera for importing tool and profile images - Complete fence can be fully swiveled away - automatic star-delta start - central lubrication Weight approx. 1360 kg Gbodpfxsyudids Aaxsl Location: Nattheim

Condition: used, machine/vehicle number: 006042, Type of edging: Thin edge, Thick edge Gluing System: EVA Hotmelt Premilling Unit: yes Corner Rounding Unit: yes Grooving Unit: yes Max feed speed: 25 m/min Maximum panel thickness: 40 mm Gbodpfx Aowacqloaxel Operating Units: 9 nr