Used Bizon Bottom Flattener for sale (2,997)

Condition: used, Year of construction: 2001, Continuous press Manufacturer: Ligmatech Type: Optimat MDE 10 Year of manufacture: 2001 Technical data Body dimensions - Length: 300 - 2500 mm - Height: 300 - 1300 mm - Depth: 120 - 600/800 mm - Pressing forces are generated electrically, both horizontally and vertically, and can be varied independently - Pressing forces are applied vertically via a pressure plate and horizontally via 3 pressure jaws each Lrodpfozuzxbox Aigor - Pressing takes place centered and on a zero line on the operator side Positioning of the pressure jaws: - Top pressure jaw with forced guidance on the top press, optionally lowerable via cylinder - Middle pressure jaw freely programmable and motor-driven - Bottom pressure jaw freely programmable and movable via a common drive with the middle pressure jaw Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2017, Automatic cold press Manufacturer: CMB Type: PFR-CCL Year of manufacture: 2017 Technical data: Motorized loading table 3,500 x 1,600 mm for manual assembly of the plates and automatic loading into the press on the 1,600 mm side. Structure made of welded steel profiles. Devices for adjusting the working height to compensate for unevenness in the floor. Steel rollers. Foot switch. PRESS Plate size: 5,500 x 1,600 mm Loading side: 1,700 mm Stroke: from top to bottom Opening: 450 mm Cold press The plates are made of steel sheet and attached to a steel frame structure. Maximum pressing force: 160 tons. Specific pressure (on 100% of the area): 1.82 kg/cm2 Specific pressure (on 80% of the area): 2.27 kg/cm2 Pressure cylinder: 12 x 80 mm Auxiliary cylinders: 6 x 50/30 mm Power supply: 400 Volt EU/50 Hz/3 PH. + G AUTOMATIC LOADING and UNLOADING of the plates on the lower plate, on the 3,500 mm side. The transport is carried out via a motorized MYLAR belt. The belt is activated by 2 rollers, one of which is located at the entrance and one at the exit of the press. The rollers are driven by a motor with a chain that slides on special guides. The Mylar belt rotates around the lower plate, which rests on special side supports. The belt rotates on 2 rollers, which are located at the entrance and exit of the press. The ends of the MYLAR belt are attached to special rods with devices for tensioning the MYLAR. The upper plate is covered with a Mylar film. The press plates consist of thick steel sheets that are welded to the frame structure. HYDRAULIC UNIT with pump, oil tank and valves for operating the pressure cylinders and auxiliary cylinders that move the upper plate. The hydraulic control unit is located in the upper part of the press to facilitate maintenance. CONTROL PANEL with buttons and switches. Pressure control manometer on the front of the press. UNLOADING MOTORIZED ROLLER TABLE 2,000 x 1,600 mm The unloading table is located at the exit of the press for manual unloading of the pressed plates. Lredpfjzuzw Djx Aigor Exit side from the press: 1,600 mm. Note: The loading table of the press with the dimensions 3,500 x 1,600 and the unloading table with the dimensions 2,000 x 1,600 are shorter than the press table with the dimensions 5,500 x 1,600, as the press was installed in a line. Note: The technical data and descriptions are a transcript of the order confirmation at the time. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 1998, Continuous body press Manufacturer: LIGMATECH TYPE: MPP 15 Year of manufacture: 1998 The MPP 15 is a flexible press for batch-related production without setup times. The MPP 15 can be used individually or in various combinations in an assembly line. The pressing forces are applied pneumatically. The separately adjustable vertical and horizontal pressure allows for pressing both horizontal and vertical bodies. The vertical forces are transmitted through a plate, while the horizontal forces act on the body via press cheeks. The position of the center press cheeks can be adjusted using adjustable stops, allowing for different heights of bottoms and sides. Lrsdpfxozuzv Tj Aigjr During the infeed process, the body is measured photoelectrically, which automatically positions the horizontal pressure bar. Technical data: Body dimensions: Length: min. 300 mm / max. 2300 mm Height: min. 300 mm / max. 1220 mm Depth: max. 600/800/1000 mm (depending on the press type) Pressing pressure: vertical max. 17 kN horizontal max. 16 kN Working height: 500 mm Transport speed: min. 8 m/min. / max. 37 m/min. Pressing time: selectable up to 999 s Operating voltage: 400 V, 50 Hz Control voltage: 24 V DC (according to VDE) Required air pressure: 5...8 bar Air consumption: 120 NL/cycle Total connected load: 3 kW Weight: approx. 4 tons Required room height: 3000 mm Extended infeed belt as a staging area Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Door panel production line Note: The system started its series production in 2023; at this point, all machines were synchronized and overhauled as needed. Used door panel production line consisting of: Ljdszuzh Ajpfx Aigerr Double-end profiler Manufacturer: Kraft Technical data - 2 scissor lift tables - 2 vacuum grippers - Infeed roller conveyor with belt conveyor - New Siemens touch control 13 roller conveyor elements Manufacturer: Kraft Technical data - Driven, approx. 3000 mm each Continuous insert material supply Special insert line HPL - Portal feeding system Manufacturer: Kraft Year of manufacture: 2023 Technical data - For singulating, aligning, and placing HPL Glue application machine Manufacturer: Bürkle Year of manufacture: 1990 Glue application machine Manufacturer: Kuper Year of manufacture: 2018 Lay-down table Technical data - Pneumatic fixing (centered on the center axis) - Device for automatic laying of battens - Fixed stop in the direction of travel, to the left of the timing belt conveyor - Positioning of the battens against the end stop for transfer with the suction system - Servo-motor driven and movable on the Y and Z axes - Uptake of the battens via a suction bar - Vacuum generation via ejector Stapling station Technical data - Servo-motor driven width adjustment of the stapling units, centered on the center axis - from min. 430 mm - max. 1,300 mm - 4 support brackets for holding the stapling components and guide units - 4 pneumatic guide units for holding the stapling units - and for the feed movement / pressure pad on the Z-axis - 4 feed slides with pneumatic pressure to fix the battens during stapling - 4 stapling units, manufacturer BEA - 2 pneumatic end stops Scoring saw Technical data - 2 units: Saw units at the top (right/left) - For creating ventilation slots - Mounted on a linear axis system for centering on the cutting width manually - Pneumatic feed of the saw units, sensing the center of the upper edge - Continuous multi-daylight press Manufacturer: Bürkle Optima 1428/50 Year of manufacture: 2017 Technical data - Start of series production in 2023 - 2 x 4 platens with a press area of 1400 x 2800 mm - With automatic feeder, manufacturer Bürkle - Removal device, manufacturer Bürkle Trimming station Technical data - For trimming overhanging edges on the top and bottom of the doors Buffer system Technical data - For intermediate buffering of semi-finished door panels - Total length approx. 14,000 mm - Solid steel construction - Approx. 200 individual compartments Label printer Technical data - Automatic label printer for labeling in-line Storage and transport system Manufacturer: Kraft Technical data - Driven storage and transport roller conveyor - Roller width 1000 mm - Total length approx. 120 meters Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is non-binding.

Condition: used, Year of construction: 1998, Four-sided planing machine Manufacturer: Weinig Type: P 23 E Year of manufacture: 1998 Technical data - Working width: 230 mm - Working height: 8-120 mm - Number of spindles: 5 (top, right, left, bottom, top) - Spindle speed: 6000 rpm - Feed rate: 5-24 m/min - Total connected power: approx. 25 kW - Infeed table: approx. 2000 mm - Weight: approx. 2500 kg Note: The technical data and descriptions are copies of the original order confirmation. The information provided is for informational purposes only and is not binding. Lrjdpfx Aszuzfueigor

Condition: used, Year of construction: 1997, Profiling line, consisting of DEP Gabbiani + Weinig planing machine DEP Manufacturer: Gabbiani Type: T-Module 80/1600 Year of manufacture: 1997 Planing machine Manufacturer: Weinig Type: 22 BL Year of manufacture: 1995 Technical data of the DEP - 6 machining motors per side - 2 fixed scoring units, 3.2 HP / 3000 + 4500 RPM - 2 chip-removing units: 12.5 HP / 3000 + 4500 RPM - 2 chip-removing units: 12.5 HP / 3000 + 4500 RPM - 2 slotting units: 12.5 HP / 3000 + 4500 RPM - 2 free spaces - 1 feed motor: 4 HP / 1400 RPM Angle transfer between DEP and planing machine - Length: 290 - 1600 mm (1800 mm) - Width: 18 - 150 mm - Thickness: 5.5 - 50 mm - Density: 600 kg/m³ - Output max.: 150 workpieces/min - Belt conveyor after the double-end profiler - Toothed belt conveyor with brush attachment as counter holder - Cam conveyor for singulation - Toothed belt conveyor as buffer section - Longitudinal discharge - Roller conveyor before the planing machine - Control: Vipa, compatible with Siemens S7 300 - Safety technology Protective door switches: 3 Safety light barriers: 1 Technical data of the planing machine Working width and working height - Working width: 20 - 230 mm (with tool diameter 125 mm) - Working height: 9 - 140 mm (with tool diameter 125 mm) Infeed table - Length: 2000 mm - Adjustment range of the jointer table: 10 mm - Adjustment range of the fence: 10 mm Surfacing table - Length: 1200 mm - Adjustment range of the table: 10 mm - Adjustment range of the fence: 10 mm Jointer spindle - Motor power: 5.5 - 15 kW Thicknessing spindle - Motor power: 5.5 - 11 kW Left spindle - Motor power: 5.5 - 11 kW 2. Right spindle - Motor power: 5.5 - 11 kW Top spindle - Motor power: 5.5 - 22 kW Bottom spindle - Motor power: 5.5 - 22 kW Lredozuzfbspfx Aigor Universal spindle - Motor power: 5.5 - 11 kW Feed - Cardan feed, continuously adjustable: approx. 6-36 m/min - Motor power: 4 - 8.6 kW Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 1999, Used 4-sided planing machine Manufacturer: WEINIG Type: Unimat 23 E Year of manufacture: 1999 with infeed unit EM11 Year of manufacture: 1999 Technical data: 5 spindles (bottom, right, left, top, bottom) Total connected load min. / max. 42 kW - 126 kW Air flow rate 30 - 32 m³ / MIN Air flow rate per spindle 28 - 32 m³ / MIN Total air flow rate 8400 - 9600 m³ / H Nominal pressure 8 bar Operating pressure 6 bar Connection diameter DN 8 Machine weight approx. 3200 kg Lrsdezuzdqepfx Aiger Static load (with support plates 80 x 100 mm) max. 120 N / CM² Note: The technical data and descriptions are transcriptions from the original order confirmation. The data is for informational purposes only and is not binding.

Condition: ready for operation (used), Year of construction: 2006, machine/vehicle number: 4547, functionality: fully functional, operating hours: 5,049 h, total height: 2,550 mm, total length: 5,900 mm, total width: 1,350 mm, overall weight: 3,000 kg, plate height: 45 mm, TECHNICAL DETAILS The machine consists of 8 processing units as follows: 1. Unit: Pre-milling unit – tools available 2. Unit: Gluing unit 3. Unit: Pressure rollers – tools available 4. Unit: End trimming unit – tools available 5. Unit: Rough milling unit – tools available 6. Unit: Edge rounding unit – tools available 7. Unit: Radius profiling unit – tools available 8. Unit: Brushing unit – tools available Panel thickness min.: 6 mm Panel thickness max.: 45 mm Panel width min.: 60 mm Panel length min.: 180 mm Feed rate control: Continuously variable Gluing system: Glue pot Voltage: 400 V Power consumption: 53.31 A Fuse: 63 A Dimensions & Weight Dimensions (L x W x H): 5,900 x 1,350 x 2,550 mm Shipping weight: 3,000 kg Note: The top and bottom stripping blades are currently not functional. Ledpfx Aiezrmtfegorr

Condition: used, Year of construction: 2009, machine/vehicle number: 113680, functionality: limited functionality, working width: 230 mm, spindle diameter: 40 mm, spindle speed (max.): 6,000 rpm, working height: 120 mm, TECHNICAL DETAILS Working width: 20–230 mm Working height: 8–120 mm Infeed table length: 1,950 mm Feed rate: 6–12 m/min Number of spindles: 5 Spindle diameter: 40 mm Spindle speed: 6,000 rpm Max. tool diameter vertical spindle: 232 mm Max. tool diameter horizontal spindle (except for the first spindle): 200 mm Spindle arrangement and power Ljdpfezrmptex Aigerr 1. Spindle, bottom: 5.5 kW 2. Spindle, left: 7.5 kW 3. Spindle, right: 7.5 kW 4. Spindle, top: 11 kW 5. Spindle, bottom: 5.5 kW MACHINE DETAILS Connection voltage: 400 V Connection power: 32 kW Fuse rating: 64 A Dimensions & Weight Dimensions (L x W x H): 4,000 x 1,400 x 1,350 mm Weight: 2,500 kg EQUIPMENT 5-spindle version Four-sided machining Infeed table CE marking Note: The 5th spindle is defective.

Condition: ready for operation (used), Year of construction: 2002, functionality: fully functional, working width: 230 mm, spindle diameter: 40 mm, spindle speed (max.): 6,000 rpm, working height: 120 mm, TECHNICAL DETAILS Working height: 120 mm Working width: 230 mm Feed rate: 6 / 12 m/min Spindle speed: 6,000 RPM Spindle diameter: 40 mm Tool diameter, vertical spindle: 100–180 mm Infeed table length: 2,000 mm Lodpfxszrmpme Aigorr Motor power 1st spindle, bottom: 5.5 kW Motor power 2nd spindle, left: 11 kW Motor power 3rd spindle, right: 11 kW Motor power 4th spindle, top: 7.5 kW MACHINE DETAILS Dimensions & Weight Dimensions (L x W x H): 3,250 x 1,550 x 1,500 mm Weight: 1,800 kg EQUIPMENT Documentation

Condition: ready for operation (used), Year of construction: 2006, machine/vehicle number: 2087, functionality: fully functional, overall weight: 4,000 kg, working width: 230 mm, spindle diameter: 40 mm, spindle speed (max.): 6,000 rpm, working height: 125 mm, TECHNICAL DETAILS Minimum working height: 8 mm Maximum working height: 125 mm Minimum working width: 18 mm Maximum working width: 230 mm Minimum feed rate: 6 m/min Maximum feed rate: 28 m/min Number of spindles: 6 Spindle speed: 6,000 rpm Spindle diameter: 40 mm Spindle motors 1. Spindle, bottom: 5.5 kW 2. Spindle, right: 5.5 kW 3. Spindle, left: 7.5 kW 4. Spindle, top: 11 kW Lrodszrmpaspfx Aigor 5. Spindle, top: 7.5 kW 6. Spindle, bottom: 7.5 kW MACHINE DETAILS Main fuse: 105 A Dimensions & Weight Dimensions (L x W x H): 7,500 x 2,000 x 1,850 mm Weight: 4,000 kg

Condition: used, mileage: 206,800 km, power: 74 kW (100.61 HP), first registration: 06/2015, fuel type: diesel, overall weight: 2,900 kg, next inspection (TÜV): 01/2028, color: white, gearing type: mechanical, emission class: euro5, total length: 5,120 mm, total width: 2,032 mm, total height: 1,982 mm, Year of construction: 2015, Equipment: ABS, air conditioning, central locking, electronic stability program (ESP), navigation system, soot filter, Special equipment: Airbag, passenger side, Ford SD audio navigation system, digital (DAB) radio reception, audio/radio remote control on the steering wheel, mobile phone/cell phone preparation with Bluetooth/USB interface, voice control and Bluetooth interface, rear wing doors, load compartment protection package, lining in the load/cargo area: high, load securing package, front and rear parking pilot system, smoker's package Ledpfszwa Ugsx Aigjrr Additional equipment: Airbag, driver side, anti-slip regulation (ASR), basic version, turn signal integrated into the exterior mirror, floor covering: vinyl in the load/passenger compartment, on-board computer, electronic brake-force distribution (EBD), interior filter: pollen filter, body/superstructure: standard van, body variant: normal roof, load compartment partition high behind driver and passenger, without window with pass-through option at the bottom, steering column (steering wheel) adjustable in height/length, truck registration, engine 2.2 Ltr. - 74 kW TDCi CAT, wheelbase 2933 mm, spare wheel in driving condition, low emissions according to emission standard Stage 5 / Euro 5, headlights H4, sliding door load/passenger compartment right, mud flaps front and rear, side protection strips, seat package 4: driver's seat (3-way adjustable) - double passenger seat, fabric, seats in the driver's cab: double passenger seat, bumper partially painted, tinted glazing, lashing rails on the side in the load compartment.

Condition: used, Year of construction: 2010, - Release agent application, top and bottom - Scoring saw with 2.2 kW motor - Trimming unit with 8.0 kW motor - Double milling unit with 2 motors, each 4.5 kW - Gluing unit - End trimming unit - Flush trimming unit - Multi-function unit - Multi-profile edge trimming unit - Spray nozzles, top and bottom - Flat edge trimming unit - Buffing unit - Grooving unit Double-sided edge banding machine Manufacturer: IMA Type: Combima/II/390/B/L12 Year of manufacture: 2010 For longitudinal and transverse feed - 2 low-maintenance precision roller chains with 75 mm wide and 85 mm long, rubber-coated chain plates, with cams - Spacing 1080 mm. Pneumatically adjustable to heights of 8, 16 or 24 mm. ICOS OPEN control system - Max. feed width 3,300 mm - Program-controlled master + slave width adjustment - Fixed stop on the left in feed direction Workpiece dimensions - Min. feed width 244 mm (for longitudinal processing) - Max. workpiece width (chain extension) 1,300 mm - Min. workpiece thickness 8 mm - Max. workpiece thickness 45 mm (with copying function) / 60 mm (without copying) Edge material: - Min. height 14 mm, max. height 65 mm - Roll material min. thickness 0.3 mm, max. thickness 3 mm Strips and edgebanding: - Min. thickness 0.8 mm, max. thickness 12 mm Feed speed - 10 - 50 m/min. with frequency-controlled drive. Infeed device - with 5 top-mounted, inclined and driven rollers. Center support with roller track - automatically lowerable and automatically centering. Equipped on each side with: Release agent application, top and bottom Scoring saw with 2.2 kW motor, 100 Hz, 6,000 RPM, pneumatically controlled. - Electronic positioning for stepless horizontal adjustment. - Vertical adjustment manually with mechanical display. Trimming unit with 8.0 kW motor, 100 Hz, 6,000 RPM. - Electronic positioning for stepless horizontal adjustment. Double milling unit with 2 motors, each 4.5 kW, 150 Hz, 9,000 RPM. - Electronic positioning for stepless horizontal adjustment. - Vertical adjustment manually with mechanical display. Gluing unit for hot melt adhesive - With single roll/edgebanding magazine for roll material up to 3 mm and edgebanding up to 12 mm - 2-fold roll magazine for roll materials up to 3 mm (can be attached to the single roll magazine) - Horizontal roll holder End trimming unit - Mounted on the upper pressure beam, with 2 motors, each 660 W, 200 Hz - Pneumatic swivel 0 + 25 for straight and miter cuts. Lodszuyqijpfx Aigjrr - Automatic adjustment for miter cuts with two different edge thicknesses (e.g. 0.4 and 1.2 mm) and for "edge overhang" for copying with edge thickness 1.0 - 3.0 mm. Automatic adjustment to the feed speed 20+30 m/min. Flush trimming unit 08.0555 - With 2 motors 1,850 W, 200 Hz, 12,000 RPM. Multi-function unit 08.353 - NC controlled with 2 motors, with automatic tooling for 4 profiles. Multi-profile edge trimming unit - with automatic tooling for 4 profiles via fixed-point control Spray nozzles, top and bottom - for applying cleaning agents Flat edge trimming unit Buffing unit - With 2 motors, each 180 W, 50 Hz, 1400 RPM. 1 Grooving unit - With 4.5 kW motor, 150 Hz, 9,000 RPM. - Horizontal and vertical adjustment manually with mechanical digital display - Pneumatic activation control - Manual swivel 90 ICOS open - PC-based control system with integrated PLC and electronic path control. - User-friendly interface with Windows standards - Simple, component-oriented

Condition: used, Year of construction: 2008, - with workpiece return - Edge thickness max: 20 mm - Board thickness: 8-60 mm - Feed rate max: 20 m/min - with groove milling unit One: Edge banding machine with return Manufacturer: Brandt Type: KDF 991 Year of manufacture: 2008 Workpiece return Manufacturer: Ligmatech Type: ZHR 05 Boomerang Lrsdpfx Aezuyp Soigor Year of manufacture: 2007 Technical data - Right-hand machine - Machine length: 8,260 mm - Ligmatech ZHR 05 length: 10,460 mm - Edge thickness max: 20 mm - Board thickness: 8-60 mm - Thickness of wound edge max: 3 mm - Workpiece width min: 60 mm - Feed rate max: 20 m/min - Stepless feed: material pressure zone adjustable via servomotor - Electromotive height adjustment - Infeed stop: adjustable via servomotor - Infeed stop for thin elements - Glue system for granules: glue pot above the feed chain - BRANDT glue system QUICKMELT QA 45 - Suitable for PUR adhesives - Magazine for single strips - Spray device, front, cleaning at the rear - Pre-milling unit - Preheating zone - End trimmers: 2 motors, pneumatically adjustable - Flush trimming: top + bottom, manually adjustable - Fine milling trimming unit: 2 motors, adjustable via servomotor R2 - Edge rounding unit: 4 motors, manually adjustable - Groove milling unit: manually adjustable with tilting function - Radius trimming blades: R2, pneumatically adjustable / Second set for R1 included - Flat trimming unit - Glue joint trimming blade - Cleaning fluid spray at the rear - Buffing unit - Solid wood edge sanding unit - Conformity marking: Including complete documentation and CE

Condition: used, Year of construction: 2010, - Application of release agent, top/bottom - Joint milling unit - Gluing unit - Trimming unit - Copy milling unit SKF-L - Profile trimming blade unit - Spray cleaning agent - Self-adjusting trimming blade unit - Buffing unit Single-sided edge banding machine Manufacturer: IMA Type: Advantage 310 Year of construction: 2010 Technical data Workpiece - Workpiece length: min. 150 mm - Workpiece width: min. 65* / 150 mm *at a max. workpiece thickness of 25 mm - Workpiece thickness: min. 8 mm, 12 mm with profile trimming blades max. 40 mm (with MFA 08.346), 60 mm (with SKF) - Smallest workpiece: 65 x 300 / 150 x 150 x 19 mm - Machining allowance per workpiece edge: 0 - 5 mm (observe max. chip cross-section) - Workpiece shape: right-angled - Material: chipboard, MDF - Surface material: direct coating (melamine resin paper), paper, film, veneer Edge material - Roll material without film: Paper edges & plastic edges: 0.3 - 3.0 mm Veneer edges: 0.5 - 3.0 mm - max. edge cross-section: 150 - 180 mm² - Cut edge strips: Strips: 3.0 - 8.0 mm - max. strip cross-section: 520 mm² - Edge height: min. 12 mm, max. 65 mm - max. upper edge overhang: 2 mm - Edge profiles Paper edge: approx. 0.4 mm, chamfer 15 Plastic edge up to 3.0 mm, radius depending on the tool Strip up to 8 mm flush milling (with interchangeable motor on MFA) Machine - Constant workpiece projection from the chain track: 35 mm + edge thickness - max. trimming cross-section 520 mm² - Throughput width: min. 65 mm (with projection of 35 mm) - min. workpiece length in feed direction: 150 mm - Overall height (top edge of chain track): 940 mm - Unit side: on the left in feed direction - Pneumatic connection: approx. 7 - 8 bar Application of release agent, top/bottom Joint milling unit 08.379 and blowing nozzle - with 2 motors, each 4 kW, 9000 RPM, 150 Hz Gluing unit 283.1513 with oil bath gearbox - Adhesive output 0.8 l, 60 mm high, with quick-lock system - can be used for hot melt adhesive or PU adhesive - with single roll / strip magazine, roll diameter 800 mm - with 3 main pressure rollers and 3 counter pressure rollers Trimming unit 08.415 - pneumatically swiveling to 0 or 8 degrees Lredszuyp Eopfx Aigor - with 2 motors 660 kW, 400 V, 200 Hz, 12000 RPM - 2 HM trimming saw blades 160 x 3.5 x 22, Z=36 Copy milling unit SKF-L - with 2 motors 180 W, 400 V, 200 Hz, 12000 RPM - and 2 motors 400 W, 400 V, 200 Hz, 12000 RPM - 1 set of DP profile milling cutter I 80x12xHSK25-R, Z = 4, with HSK25 shank - Profile length in the feed direction: max. approx. 50 mm - Workpiece thickness: max. 60 mm - Working speed: max. approx. 20 m/min - Distance between 2 workpieces: min. approx. 400 mm - min. workpiece projection = 35 mm + profile depth Profile trimming blade unit 08.519 - For finishing a top and bottom milled quarter-circle profile Spray cleaning agent Self-adjusting trimming blade unit 08.521 - for removing hot melt adhesive residue from the edge area of the top and bottom of the workpiece Buffing unit 08.617-2 - with an upper and lower motor: 180 W, 50 Hz, 1400 RPM - 2 polishing pads 50 x 160 x 19 mm

Condition: used, Year of construction: 2017, Edge banding machine Manufacturer: Homag Type: Optimat KDF 440 C Year of manufacture: 2017 Technical data Workpiece thickness: 8 - 60 mm Edge material: 0.4 - 8 mm (depending on the equipment) Feed rate: 8 - 18 m/min (stepless) Workpiece length min. approx. 120 mm Workpiece width min. approx. 60 mm Glue application EVA hot melt adhesive, optionally PUR-compatible Glue reservoir Teflon-coated, quick-change system possible Total connected load approx. 15 - 20 kW (depending on the equipment) Compressed air requirement: 6 - 7 bar Machine weight: approx. 3,000 - 3,800 kg Control system: powerControl / powerTouch CE marking Equipment: Joint milling Glue application Pressure zone Cut-off saw unit Milling unit top/bottom Corner rounding unit Lrodpfjzuykcjx Aigsr Scraping blade unit Edge finishing unit Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2009, Edge banding machine Manufacturer: IMA Type: Novimat/I/G80/650/R3 Year of manufacture: 2009 Technical data - Workpiece overhang from the chain conveyor: 38 mm - Feed width: min. 65 mm (with max. workpiece thickness of 25 mm) - Workpiece length in feed direction: 150 mm - Overall height (top edge of chain conveyor): 960 mm - Feed speed: approx. 6 - 30 m/min, electrically adjustable - Machine control system ICOS open compact Workpiece - Workpiece length: min. 150 mm - Workpiece width: min. 65 mm - Workpiece thickness: 8 - 40 mm (with edge trimming function) / 60 mm (without edge trimming function) - Smallest workpiece: 150 x 150 mm or 65 x 300 mm - Edge material: paper, plastic and veneer - Height: 14 - 65 mm - Roller material thickness: 0.3 - 3.0 mm (veneer edges limited to max. 1.0 mm) - Max. upper edge overhang: 5 mm Units Infeed area - Release agent applicator mounted at the top and bottom, not adjustable Edge trimming - 2 motors 4.5 kW, 150 Hz, 9000 rpm - incl. frequency inverter with braking function - Motor 1 counter-rotating - Motor 2 co-rotating Gluing unit VTG 3-6 - with one preheating nozzle 300 mm for preheating the workpiece edge - 6-position edge magazine for roller material 0.3 - 3 mm thick. - 1 driven main pressure roller and 4 pressure rollers, with scraper, pneumatically adjustable Glue application - with pneumatic quick-lock system - Chem-Coat coating - electronic temperature control - Volume 0.8 l Pre-melting tank approx. 1 l - Heating power 3 x 400 W - with EVA glue, approx. 7.0 kg/h - with filler-free glue, approx. 5.0 kg/h Cutting unit - 2 motors 660 W, 200 Hz - incl. frequency inverter with braking function - pneumatic pivoting 0+25 for straight and bevel cutting Flush trimming - 2 motors each 1000 W, 400 V, 200 Hz, 12000 rpm - with HSK 25 shank - incl. frequency inverter with braking function Multi-profile trimming unit - 2 motors each 660 W, 400 V, 200 Hz, 12000 rpm - with HSK 25 shank - incl. frequency inverter with braking function - for trimming 4 profiles - with stepper motor axes for horizontal and vertical positioning Lodezuyi Ejpfx Aigerr Contour trimming unit KFA x30 - 1 motor 500 W, 400 V, 400 Hz, 18000 rpm - Program-controlled conversion for up to 4 profiles - incl. fine positioning for different edge thicknesses Multi-profile scraping blade - Stepper motor axes for horizontal and vertical positioning - Scanning from above and below (max. 4 profiles) - Scanning from the side via pneumatic pressure Spray nozzles at the top and bottom for applying cleaning agents - fixed, not adjustable Surface scraping blade - with height sensing skid - electronically controlled horizontal positioning Buffing unit - 2 lower and 2 upper motors, 180 W, 50 Hz, 1400 rpm - 1st motor pair with cloth-sisal discs 50x160x19 mm - 2nd motor pair with polishing discs 50x160x19 mm - The motors operate in the same direction and are both tilted and pivoted in the feed direction. - Each motor can be individually adjusted vertically 2x NC-controlled grooving - 2 milling motors each 4.5 kW, 150 Hz, 9000 rpm - incl. frequency inverter with braking function - one manual 90-degree pivoting device from 180 -270 with co- and counter-rotating function - Horizontal, stepless adjustment with AC servo motor for grooving unit Workpiece return Note: The technical data and descriptions are copies of the order confirmation at the time. The information is for informational purposes only and is non-binding.

Condition: used, Year of construction: 2010, - Equipped with ISAS 28-position edge magazine - PU gluing unit - With Boomerang return system Single-sided edge banding machine Manufacturer: Homag Type: KAL 310/7/A3 Year of manufacture: 2010 Technical data - Equipped with ISAS 28-position edge magazine - PU gluing unit - With Boomerang return system Edge trimming unit with 2 motors, each 3KW, 150 Hz, 9,000 RPM. Pneumatically controlled for pre-trimming PU gluing unit 34 with PU hot melt unit - capacity max. 6 kg/h Container size 2 kg. QA glue application unit Selectable edges from the ISAS 28-position edge magazine 4 pressure rollers Release agent spray unit, top and bottom Trimming unit WK 13, bevel / straight With 2 motors, each 0.4 KW, 200 Hz, 12,000 RPM. Electropneumatic adjustment of the trimming motors to 2 positions (flush trimming and with overhang) Pre-trimming unit with 2 motors, each 0.55 KW, 200 Hz, 12,000 RPM. With double-roller scanning. With electropneumatic adjustment Ledpfezuyhhjx Aigjrr Shaping trimming unit FK 11 - manual For processing the edge overhangs on the top and bottom edges of the workpiece, as well as for milling the front and rear edges With 2 motors, each 0.4 KW, 200 Hz, 12,000 RPM. Universal trimming unit UF 11 With motor 4 KW, 150 Hz, 9,000 RPM. Swiveling 90°, electropneumatically controlled With HSK 63 F collet for unlocking by push-button Profile scraping unit PN 10 Pneumatic adjustment for moving sideways out of the working area Finishing unit FA11 top/bottom Consisting of: Glue joint scraping blade Cleaning agent application Buffing unit with 2 motors, height adjustment with the upper pressure Machine control via 19-inch touchscreen Return system BOOMERANG ZHR05 With air cushion table, angled, length 2,000 mm, width 1,000 mm Conveyor belt width 1,100 mm Workpiece parameters: Length 300 - 2,500 mm / Width: 60 - 1,100 mm or Length 300 - 800 mm / Width: 1,100 - 2,000 mm Thickness 8 - 60 mm For 4-sided processing: Min. part size: 300 x 300 mm / max. part size 2,000 x 800 mm With roller strip for supporting wider parts.

Condition: used, Year of construction: 2004, - Pre-milling unit - Glue application unit (hot melt) - Pressure zone with pressure rollers - Cut-off saw - Edge trimming/radius milling unit (top and bottom) - Corner rounding unit - Radius scraping blade - Glue scraping blade - Polishing units Edge banding machine Manufacturer: Brandt Type: KDF 560 Year of manufacture: 2004 Lredpfx Aijzux T Ajgjr Technical data - Voltage: 400 V / 50 Hz / 3 phases - Connected load: 13.2 kW - Fuse rating: 35 A Equipment - Automatic unit adjustment via the PC control system - Control: Brandt Power Control PC20+ - Suitable for thin and thick edges (ABS, PVC, veneer, and solid wood edges) - Edge thickness: approx. 0.4 to 8 mm - Workpiece height: approx. 8 to 50 mm - Feed speed: 14 m/min Installed units - Pre-milling unit - Glue application unit (hot melt) - Pressure zone with pressure rollers - Cut-off saw - Edge trimming/radius milling unit (top and bottom) - Corner rounding unit - Radius scraping blade - Glue scraping blade - Polishing units Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2003, - Workpiece length: 800 - 3000 mm - Workpiece width: 350 - 1400 mm - Workpiece thickness: max. 70 mm with edge / max. 80 mm for milling - Main spindle 12 kW - Tool changer, 18-position CNC machining center Manufacturer: Homag Type: PROFI BAZ20/30/16/V/D Year of manufacture: 2003 Technical data Homatic - CNC control CNC programming system WOODWOP Postprocessor Workpiece dimensions - Workpiece length: 800 - 3000 mm - Workpiece width: 350 - 1400 mm - Workpiece thickness: max. 70 mm with edge / max. 80 mm for milling - Edge band width: min. 120 mm - Weight: max. 150 kg Throughfeed table - Longitudinal console 1, fixed installation - Longitudinal console 2, manually adjustable via width adjustment in the Y-direction - 8 vacuum clamps 125 x 50 x 100 mm - Working height, bottom edge of workpiece: 950 mm Motor, width adjustment, longitudinal console, traversing table - For different workpiece widths via servo drive for throughfeed table - Per longitudinal console Chip conveyor - Chip and waste disposal via integrated chip conveyor under the longitudinal traverse Stop pins for top layer overhang - Stop pins with lifting-rotating mechanism for workpieces with max. 20 mm top layer overhang - Individually selectable, end position monitored, stroke 110 mm - For manual placement of doors Vacuum pump 100/140 m3/h Unit for positioning the vacuum clamps - Mounted on the unit carrier with pneumatic extension console - For max. 4 vacuum clamps per longitudinal console Main spindle 12 kW - Tool holder HSK F63 - Extraction system for all tools and units - Three-phase asynchronous motor 12 kW at S1, water-cooled - Tool weight: max 6 kg incl. holder - Tool length: max. 200 mm from the motor spindle bottom edge - Tool diameter: max. 180 mm for milling tools / max 200 mm for sanding tools - Frequency converter: 15 kW - Speed range: 1500 - 18000 rpm, stepless, programmable - Full rated power from 12000 rpm Unit interface for the main spindle Lsdpfx Aijzux Tpjgerr - For connecting the machining units - Pneumatic and swivel drive interface - C-axis with torque transmission and 3-point support Tool changer, 18-position For tools and units with HSK F63 Tool weight: 6 kg Tool length: max. 200 mm from the motor spindle bottom edge The following tool and unit configurations are possible - 18 x max. 130 mm - 9 x max. 180 mm and 9 x max. 70 mm - Tool diameter max. 200 mm for sanding tools - Tool changer can be raised for a moving pick-up station on the left side Drilling/milling unit, 4 spindles, for tool changer - For automatic changing in the main spindle - Collet holder ER25 up to max. 16 mm shank diameter - Tool protrusion max. 50 mm - Speed: max. 13500 rpm - Standard collet 10 mm - Infinitely swiveling via the C-axis - Without tool Lock case milling unit, 2 spindles, D=16/20 - With integrated blow-out nozzle - Two-sided spindle outlet with counter-rotating direction - Speed: 12000 rpm - Infinitely swiveling via the C-axis - Without tool 1x Weldon chuck: 20 mm - Reducing sleeve for tool 16 mm - Total tool length: 180 mm - Tool protrusion: max. 135 mm 1x ER16 collet with 10 mm - Total tool length: max. 70 mm - Tool protrusion: max. 40 mm Sawing/drilling unit, swiveling, for tool changer - For miter cuts and angled drilling - Manually swiveling 0 - 90 degrees - Mounting flange 30 mm with countersunk head screws - Tool diameter 52 mm - Prepared for miter saw: max. 180 mm - Drill chuck with Weldon chuck: D=10 mm - Speed: max. 9000 rpm - Infinitely swiveling via the C-axis -

Condition: used, Year of construction: 2008, Single-sided edge banding machine Manufacturer: HOMAG Type: Optimat KAL210/6/A20/S2 Year of manufacture: 2008 Single-sided machine for joint milling of straight workpiece edges, edge banding and finishing of various edge materials from rolls or as strips, up to 20 mm edge thickness, in longitudinal and transverse operation. power control PC22 Modern control system based on Windows PC Technical data - Feed rate 18 - 25 m/min. - Feed rate with profile milling cutters FK11 max. 20 m/min. - Workpiece thickness 8 - 60 mm - Edge material strips max. 0.4 - 20 mm - Edge material rolls 0.3 - 3 mm Joint milling unit - 2 motors, each 3 kW, 150 Hz, 9,000 rpm. for joint milling of the workpiece edge before edge banding - electropneumatic control of both motors Gluing unit A20 - 2 rollers Quickmelt hot melt adhesive unit - Temperature control electronically with LED display Magazine for 1 roll, manual - for solid edges, strips and rolls - 1 edge feed - 1 roll holder Pressure zone C - 1 driven pre-pressing roller, diameter 150 mm - 6 after-pressing rollers, diameter 70 mm Trimming unit HL84 / 0.8 kW - 2 motors, each 0.8 kW, 200 Hz, 12,000 rpm. - Motors can be manually swiveled for chamfer trimming Pre-milling unit 1.5 kW - 2 motors arranged one above the other, each 1.5 kW, 200 Hz, 12,000 rpm. Profile milling unit FK11, manual - For processing the edge overhang on the top and bottom edges of the workpiece and for milling the front and rear edges of the workpiece Belt sanding unit KS 10 - for sanding straight and solid wood edges, oscillating, sanding pressure manually adjustable Profile sanding unit PS 10 - sanding from below, for sanding profiles, sanding pressure manually adjustable Automation package Chamfer / Radius KAL210/6/A20 - Automatic adjustment of the infeed fence - Automatic adjustment of the pressure zone - Pneumatic adjustment from chamfer to straight trimming - Pneumatic adjustment of the trimming motors for flush or overhang trimming - Pneumatic adjustment of the pre-milling unit for flush or overhang milling - Automatic adjustment from chamfer to radius milling during profile milling - Pneumatic adjustment PN10 / FA11 - Electronic height adjustment Lrodpfx Aijzux R Iegor

Condition: used, total width: 2,600 mm, total height: 1,750 mm, Colour: Green Dimensions (LxBxH): 130 x 260 x 175 cm - Documentation available: No - CE certificate present: No - Number of spindles [pcs.]: 4 - └ Spindle 1: - - Spindle type: Bottom - - Max. planing block diameter [mm]: 120 - - Tool present: Yes - └ Spindle 2: - - Spindle type: Top - - Max. planing block diameter [mm]: 120 - - Tool present: Yes - └ Spindle 3: - - Spindle type: Left - - Motor power [kW]: 11 - - Spindle diameter [mm]: 50 - - Max. planing block diameter [mm]: 120 - - Tool present: Yes - └ Spindle 4: - - Spindle type: Right - - Motor power [kW]: 11 - - Spindle diameter [mm]: 50 - - Max. planing block diameter [mm]: 140 - - Tool present: Yes - Max. planing width [mm]: 500 - Max. planing height [mm]: 200 - Feed table length [mm]: 650 - Feed roller diameter [mm]: 120 - Feed motor [kW]: 10 - Tool type: Standard - Diameter extraction nozzle [mm]: 180 - Voltage [V]: 400 - Current consumption [A]: 55.2 - Power [kW]: 26.7 - Transport dimensions: 1300mm x 2600mm x 1750mm (l x w x h) Lsdpfx Ajwniy Njigorr - Transport packages [pcs.]: 2 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Year of construction: 1972, Colour: Green Empty weight: 3.000 kg Dimensions (LxBxH): 180 x 170 x 200 cm Four-sided planer Küpfermuhle 600 planing width 600 mm planing height 190 mm Angled bottom cutterblock 9 kW Top inclined cutterblock 11 kW Vertical spindle right 4 kW Vertical spindle left 5.5 kW Dimensions approx. 1800 x 2000 x 1700 mm (LxWxH), Weight 3000. - Year: 1972 - Documentation available: No - CE certificate present: No - Serial number: 9552 - Max. working width: 605 - Max. working height: 200 - Knife type: Standard - Number of knives per cutterhead [pcs.]: 4 Lrodpfx Aiownhbxsgjr - Number of cylinders height adjustment: 2 - Height adjustment type: Manual - Min. feed speed [m/min]: 7 - Max. feed speed [m/min]: 23 - Voltage [V]: 400 - Current consumption [A]: 65 - Transport dimensions: 1800mm x 1700mm x 2000mm (l x w x h) - Transport weight [kg]: 3000kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Condition: NEW with pneumatic clamping device. The universal assembly station for the production of wall, ceiling and roof elements in timber frame construction,ceiling and roof elements in timber frame construction. - Heavy-duty, basic structure of the machine frame for a flat work surface - Clamping of the elements via 9 system clamping beams with pneumatic pressure cylinders. The system clamping beams are extendable for element heights from 100 to 3,800 mm. The cylinder stroke is 320 mm, the clamping force per cylinder is approx. 420 kg/4,200 N. at 10 bar operating pressure It can be clamped in two groups of 5 pieces and 4 pieces, two elements can be clamped/worked on at the same time. - Planking of the work surface as far as technically possible with wooden panels. (A perforated metal panel is available as an option, as shown in the photo)) - Stop system at the bottom with 9 pins and at the side with 7 pins for dimensionally accurate elements. - Swivelling device of the assembly station via 3 hydraulic cylinders for panel weights up to panel weights of up to 4,000 kg to 85° (95°). The hydraulic system is compactly integrated in the frame area of the assembly station. - The electrical control cabinet is also installed underneath the assembly station for protection. - The functions are operated via a control bottle. Lrsdpfxszhnafo Aigor - A compressed air connection and socket are installed on both ends of the station. and on the long side of the station there are 2 sockets and 2 compressed air connections compressed air connections for connecting hand-held devices. - The stations are modular in design, so that they can be expanded immediately or later with a to form a complete turning station. You can see a turning station in picture 3. - Further options: Assembly table without set-up function Perforated metal panels Other working dimensions on request Working area: - Maximum element size (W x H): 12,000 x 3,800 mm - Minimum element size (W x H): 1,000 x 100 mm - Cylinder stroke of the clamping cylinders: 320 mm - Stop/ socket pin height: 120 mm - Working height: approx. 700 mm - Colour RÁL 7035 light grey

Condition: ready for operation (used), Year of construction: 1998, overall weight: 8,600 kg, This 6-axis TRUMPF TrumaBend V85S press brake was manufactured in 1998. It features a bending length of 2,550 mm, an 850 kN bending force, and a 6-axis back gauge. The Delem 65 CNC control enhances precision, while the electro-hydraulic twin cylinder drive ensures robust performance. If you are looking to get high-quality bending capabilities, consider the TRUMPF TrumaBend V85S machine we have for sale. Contact us for more information about this machine. Additional equipment • Extended Installation Height and Stroke: Additional 150 mm each • 2nd Foot Switch Machine Benefits Technical Machine Benefits • Drive type: electro-hydraulic twin cylinder with independent y1/y2 movement • Power requirements: 11 kw / 415 v / 50 hz • Design: down-stroking with dual cylinder electro-hydraulic ram drive via proportional valves • Inclination of beam (y1/y2): +10 mm • Bending force: 850 kn // gap between columns: 2260 mm // throat depth: 410 mm // stroke length: 215 mm // open height: 385 mm • Bed width: 120 mm • Ram measurement: incremental with deflection compensation • Tool holders: self-centering top tool holder, hardened bottom tool holder • Hydraulic tool clamping: hydraulic clamping for both top and bottom tools • Safety features: safety screens, light barriers, single/double break modes // front support brackets: two quick-adjustable brackets Extra Information Back Gauge: CNC-controlled ‘X’ and ‘R’ axis back gauge with safe 2-finger adjustment X-axis Back Gauge Travel: 600 mm Maximum X Distance: 860 mm R-axis Vertical Travel: 250 mm Back Gauge Travel Speed: 500 mm/sec R-axis Speed: 300 mm/sec Z1/Z2 Axis: CNC-controlled, asymmetric finger adjustment Working Speeds: Approach Speed: 200 mm/sec Operation Speed: 1–10 mm/sec Lrodpfx Aiszuxkhoger Return Speed: 135 mm/sec Technical Specification Bending Length 2550 mm