Press brake

LAMI NOVA P 1340

Condition: used, Year of construction: 2025, operating hours: 2 h, Operating hours: 2 New tractor with dealer daily registration prior to delivery Standard equipment / technical data Engine Rated power (ISO): 82 / 110 kW/hp at 2200 rpm Maximum power: 86 / 115 kW/hp at 2000 rpm Maximum torque: 460 Nm at 1600 rpm Manufacturer / Type: Agco Power / AP 44MBTN-D5 Low-emission engine, 4-cylinder / 4.4 l, 4 valves, STAGE 5 Regulated turbocharger, SCR catalytic converter DOC – Diesel oxidation catalyst SC soot particle filter One-piece, tiltable engine hood Exhaust on right side, in front of cab Fuel tank capacity: 198 liters / AdBlue: 18 liters Transmission / PTO 16/16-Speed Dyna-4, SpeedMatching, 40 km/h PowerControl left-hand operation with powershift reverser, 4-step powershift Permanently cooled wet multi-plate clutches with independent lubrication system Dual-speed PTO: 540 / 540E / 1000 rpm Electronic shift in cab PTO START/STOP button on left rear fender Hydraulics / Rear linkage Open Center system, 58 l/min total flow, max. 200 bar 2 control valves with hydraulic couplers: 1x single/double-acting, pressure relief + 1x single/double-acting, neutral leak, SST Category 3 quick coupler with balls and catcher bowls CAT 3/2 Lower link draft control 5,200 daN maximum lift force, 2 external lift cylinders Adjustable lift rods on both sides and 2 side stabilizers EHR with external operation on both rear fenders Electrical equipment Thermostart, 120 A alternator Electric battery isolation switch 12 Volt power supply for external devices with socket Axles / Additional weights Rear axle ND with flange hub Oil-cooled disc brakes Height-adjustable automatic drawbar Rear fender outer width 2.00 m, without extensions Front weight carrier with integrated drawbar and towing pin Driver's station Standard cab with vibration damping, standard roof, ventilation and heating, air conditioning Integrated safety frame with tinted glass Doors on both sides with safety steps Adjustable steering column (height & tilt) Air-suspended driver's seat with armrests, swivel adapter, and seat belt 2 large telescopic exterior and wide-angle mirrors Interior mirror Analog-digital dashboard (SIS) Radio pre-wiring with antenna and speakers 4 work lights each at the front and rear of the cab roof 2 headlamps each in the engine hood and on the handrails, 2 work lights on rear fenders Rear window washer/wiper All-wheel front axle with selectable differential lock Special equipment With fuel tank protection PowerControl & brake to neutral (clutch effect) 100 l/min Open Center hydraulic system oil flow sharing (58+42 l/min) Leak oil collector at quick couplers 3 control valves: 1x pressure relief, double-acting, float, SST + 1x double-acting, neutral leak, SST + 1x double-acting, neutral leak, SST + free return 2.5 t front linkage, 1 hydraulic hose set, electrical socket 480/70R38 ADJ Ø1.69m & 380/70R28 ADJ Wide rear fender extensions Air conditioning Cab with mechanical suspension Telescopic exterior and wide-angle mirrors Passenger/instructor seat with belt Air-suspended driver's seat, automatic setting with seat belt, swivel adapter, and armrests Dkedpfx Aeyvmq Ijg Dok Rear window washer/wiper Automatic battery isolation switch, 12

Condition: ready for operation (used), Year of construction: 2014, operating hours: 48,274 h, pressing force: 326 t, number of axes: 6, This TRUMPF TruBend 7036 press brake was manufactured in 2014. It features a robust welded steel frame, electro-hydraulic top drive, and a 2D graphic control DA 69 system on a 10.4" color screen. The machine includes a CNC backgauge with 6 axes, hydraulic tool clamping, and CNC crowning for precise bending. Regularly serviced under a TRUMPF maintenance contract. Contact us for more information about this machine. • Free column clearance: 3680 mm • Installation height: 535 mm • Control system: 2d graphic control da 69 on windows with 10. 4" color screen • Electrical equipment: for three-phase current 400 v / 50 hz • The machine was serviced annually • Maintenance contract in place • Sturdy machine frame, welded all-steel construction • Press beam with high bending strength • Highly dynamic electromechanical direct drive (torque motor) • Electro-hydraulic top drive via proportional valves • Modern block hydraulics • Inductive length measuring system with temperature compensation • CNC backgauge system: 3-axis (X1, R1, Z1) and 6-axis options • Rack and pinion drive for X and R axes • Safe, front-accessible movement of stop fingers • Modufix top tool holder system, self-centering, manual clamping • Manual lower tool holder for EV dies, hardened, programmable offset • Integrated TRUMPF TASC 6000 control • Numerical workshop programming • Embedded Windows XPe operating system, Pentium M 1.1 GHz • 1 GB RAM • 15-inch touchscreen • Network-enabled, teleservice via modem • Control cabinet climate control • Side-hinged safety doors and rear protective cover • 2-button foot switch for standing or seated operation • Rear work area LED lighting • Front work area LED lighting • Ergonomics package: comfortable front work surface and footrest • 2 storage brackets and 2 document trays • 24000 operating hours, brakes replaced 2024 • Tools maintenanced by TRUMPF, all in tolerance Additional equipment Dodpfx Asx D D Hyog Dskk • Backgauge system with 5 axes and control cabinet climate control • Upper tool clamping: hydraulic and hardened • Lower tool clamping: hydraulic • CNC Crowning • BendGuard safety device • Foot switch • 2x support consoles, front • 1x bending aid with 900 mm parking position • Table extension for base table / additional table Technical Specification Bending Length 1020 mm

Condition: new, 88 degree standard press brake punch H120mm for Amada/Promecam/Durma/Baykal/Ermaksan/Mvd/Denner/SBD Dsdpfx Agjiiq H Dj Dskk

Condition: used, mileage: 166,000 km, power: 96 kW (130.52 HP), first registration: 11/2012, fuel type: diesel, overall weight: 3,500 kg, color: white, gearing type: mechanical, emission class: euro5, number of seats: 3, loading space length: 3,850 mm, loading space width: 2,040 mm, loading space height: 400 mm, Equipment: ABS, central locking, * 1st hand * Aluminum platform * Mounting eyes * 6-speed * Driver's airbag * stereo * rail Dsdpfx Asglgpnog Dokk * Payload 1500kg * WhatsApp/Tel.

Condition: new, Year of construction: 2024, ♻ Universal use (diverse wood, pallets with nails and pins, particle boards, waste and scraps, veneer, MDF plates, cardboard boxes, plastics, textile etc.) ✔ Power: 22 kW ✔ Shaft length: 650 mm ✔ Shaft diameter: 270 mm Dksdpjhwwpzofx Ag Djk ✔ Shaft RPM: 80-120 rpm ✔ Number of cutting knives: 2x14 ✔ Granulation: 10-50 mm ✔ Capacity: up to 5 m3/h* ✔ Material discharge opening: 160 mm ✔ Filling opening: 1446 x 1342 mm ✔ Dimensions L/W/H: 1,92/1,55/1,79 m ✔ Weight: 1750 kg 2 years warranty or 2000 working hours

Condition: new, Year of construction: 2024, == Exhibition machine == ALZMETALL column drilling machine ALZSTAR 40 SV with coolant unit B (option 25) (consisting of separate tank (33l), pump with motor protection switch, complete fitting) and LED machine light Standard equipment: Mushroom pushbutton, reversing switch (for clockwise and anticlockwise rotation), motor protection switch Infinitely variable speed adjustment, digital speed display, feed overload protection, protection class IP54, connection plug Spindle protection with electrical fuse Technical data: Drilling capacity steel E335 (St 60) 40 mm Thread cutting: Steel E335 (St 60) M 24 Cast iron EN-GJL-200 (GG20) M 30 Short spindle MK 3 Spindle stroke 120 mm Projection 293 mm Column diameter 115 mm Machine table, usable support 514 x 360 mm T-slots, number x width x distance 2 x 14 x 224 mm Spindle-to-table distance min./max. 117/701 mm Feed rate 0.10 + 0.20 mm/rev Machine height without options approx. 1840 mm Net weight approx. 285 kg Dedpfx Asd Hy Eleg Djkk Drive stepless Motor 1500 / 3000 rpm Power 1.45 / 1.9 kW Spindle speed 160-2250 rpm

Condition: ready for operation (used), Year of construction: 1996, pressure 80.0 t chamfer lenght 2550 mm distance between columns 2130 mm column arm 420 mm ajustment speed 100 mm/sec working feed 10.0 mm/sec return speed 80.0 mm/sec stroke 200 mm dayligth 470 mm table width 60.0 mm table height 910 mm Number of working hours ca. 37.102 h total power requirement 9.0 KW weight of the machine ca. 5750 kg range L-W-H 3100 x 2180 x 2540 mm good / well-maintained condition (!!) - Inspected condition - Machine video - ?v=fwdjSiQYq_A Equipment: - CNC electro-hydraulic press brake Dodpsxabnyjfx Ag Dskk - OPERATEUR CNC control for 8 axes X1 + X2, Y1 + Y2, R1 + R2, Z1 + Z2 - CNC-controlled backgauge adjustment (X-axes) - CNC-controlled vertical adjustment of the stop fingers (R-axes) - CNC-controlled left-right adjustment of the stop fingers (Z-axes) - Freely movable two-hand control & foot switch - Tool crowning - AMADA type - Various tools - CE marking - Side guards (hinged doors) - Rear guards (hinged door) - 2x emergency stop buttons at the front - Operating instructions

Condition: excellent (used), feed length X-axis: 450 mm, feed length Y-axis: 300 mm, feed length Z-axis: 300 mm, CNC TOS INTOS ZEBRAK FNG30 milling machine TNC310 Heidenhain control X450mm Y300mm Z300mm Dksdpfx Agjrq D Uke Djk tool clamping hydraulic inverter on spindle SK40 machine in very good condition

Condition: used, Year of construction: 1987, Technical details: pressure: 200 t chamfer lenght: 4000 mm distance between columns: 3530 mm control for program: DNC 7000 max. stroke: 220 / min: 200 mm throat: 320 mm ajustment speed: 70 - 80 mm/sec working feed: 10 mm/sec return speed: 49 mm/sec back gauge: 700mm motorisch table-size: L x B: 4110 x 180 mm work height max.: inkl. Tischverlängerung mm interface: RS 232 connection voltage: 380 V total power requirement: 15 kW weight of the machine ca.: gesamt: 17,0 t machine dimensions LxWxH: 4,6 x 1,6 x 3,3 m Dsdpfxju Icc Ae Ag Dokk incl. 2 pieces table extensions rear support 700mm travel motorized and 2 pieces support blocks with travel 1500mm motorized right/left operation via control panel swiveling and 2x foot operation Hydraulics: max. pressure 318bar; oil filling approx. 170 liters; pump capacity 19.3 l/min. Control DNC 7000, graphic display, PC software equipment: Cutting zone lighting stroke counter div. Tools optional *

Condition: good (used), Year of construction: 2017, In this offer you buy used office furniture, which is in good condition. They were delivered in 2017 and are generally in very good condition, since little used. Items for sale: We also offer workplace sets for 450€. 1x desk - Manufacturer: FM - 160 x 80 x 76 (stepless height adjustable 68cm to 76cm) - gray top - aluminum frame Dkodpfjiiv Ikox Ag Djk 1x office chair "Dauphin MagicShape elan - armrests - completely adjustable - cover polo grey/black 1x mobile pedestal - Manufacturer: FM - 43,4 x 80 x 59 - one material drawer - 3 steel drawers with softclose - lockable incl. key Desks: - Approx. 10x desk from the manufacturer FM 1600 x 800 x 680 to 760 (infinitely height adjustable) in the color light gray. Frame made of aluminum - Approx. 12x folding table (can be used as a desk) 1600 x 800 x 720 on castors, in the color light gray. Aluminium frame - Approx. 2x round meeting table 1000mm diameter in the color light gray. Aluminium frame - Approx. 4x high table 1600 x 800 x 1300 in the color arctic white. Frame in white aluminum Chairs: - Approx. 10x Dauphin swivel chair MagicShapeS elan with armrests and fully adjustable. Fabric cover Polo black, base plastic black - Approx. 44x Interstuhl Hero 550H cantilever chair with armrests. Upholstery in ruby red color. Metal frame chrome-plated. - Approx. 52x Interstuhl Hero 550H cantilever chair with armrests. Upholstery in the color ocean blue. Metal frame chrome-plated. - Approx. 10x Interstuhl Kinecticis5 710K bar stool with footrest. Upholstery in the color black. Frame in silver color. - Approx. 16x Interstuhl Kinecticis5 710K bar stool with footrest. Upholstery in the color ocean blue. Frame in silver color - 12x Interstuhl Kinecticis5 710K bar stool with footrest. Upholstery in the color red. Frame in the color silver - 16x Interstuhl Kinecticis5 710K bar stool with footrest. Upholstery in the color ruby red. Frame in the color silver Storage space: - Approx. 16x FM 434 x 800 x 590 mobile pedestal with one material drawer and 3 steel drawers. Body completely in the color light gray. Handles made of aluminum meeting table with 4 conference chairs - 750,-€ net high table with 6 bar stools - 1500,-€ net Prices may vary slightly depending on the quantity purchased. We will be happy to prepare a suitable offer for you. You can also purchase each piece of furniture separately. Condition: This offer is used furniture, which may show signs of use (minor scratches or yellowing). Packing and shipping: You are welcome to look at everything during our business hours. Please make an appointment for this! Seaworthy packing and worldwide shipping is possible on request! For more information you can of course also contact us personally.