Used KASTO band- hack- and circular saws

KASTO Band- / Bügel- / und Kreissägen

Condition: reconditioned (used), Stock - No.: 2553 1 used, partly overhauled and functionally tested Single-Screw Extruder, equipped with: Material hopper loader Extruder BATTENFELD Typ UNI-EX 1-75-25 B Screw - Ø 75 mm – 25 L/D, Cylinder Air-cooled Extruder-Motor 120 kW – DC ( overhauled ) Screw –speed up to 130 r.p.m. additional Temperature controllers for down-stream equipment Control-Board with melt-pressure sensor / Display. Inspectiuon visist / trial-run shortly by appointment in our workshop Wuppertal Germany possible. Gbjdpfx Agsiyynde Reg We can offer, installed to this extruder: > screen-pack-changer > pelletizing ( strand, hot-face or waterring ) > other equipment Send us your inquiry. More extruder and complete pelletizing lines ex our workshop Wuppertal, send us your inquiry or visit us, you´re welcome

Condition: new, Comparable to Behringer, Kaltenbach, Kasto, Jaespa, etc. Patented miter system Gbodpfx Agjh S Nxpj Rsg Continuously adjustable cutting speed Hydraulic feed control Hydraulic lifting and lowering of the saw frame Hydraulic material clamping Powerful frequency-controlled saw drive Swivel range 30° right / 45° left Cutting range in mm: 45° left round 300, flat 300 x 300 90° round 410, flat 620 x 410 45° right round 360, flat 420 x 360 30° right round 300, flat 300 x 300 Remnant piece length without bundle clamping: 60mm Recommended options: Micro-spray device Laser light Clamping pressure regulator Powered chip brush Manual support roller Set-up elements

Condition: new, 900 mm 900 mm 900x900 mm saw band length 9300 x 67 x 1,1 mm table height 790 mm band speed 14 - 60 m/min total power requirement 11 kW weight of the machine ca. 8,45 t dimensions 4,485 x 1,68 x 3,15 m The semi-automatic, hydraulic saws from the X-tech line offer the best Saw technology and best performance when cutting special steels • The electro-welded machine frame and the steel saw frame meet requirements all cutting needs and eliminate vibration and noise. • The chip conveyor is hydraulically driven and the speed is adjustable • All movements of the machine (saw frame, vice, feed, Saw band guides) are carried out thanks to modern linear guides with high static and dynamic load performance, which also has very low sliding friction to guarantee. • Another characteristic feature is the roles for the Positioning of the material by a hydraulic motor are driven. They move at right angles to the material, and thus allowing optimal clamping of the material. • Thanks to the height control of the saw band position, the operator can place the band in place near the top edge of the material. After the cut is finished, the tape automatically raised back to the previous position. Alternatively you can also “Remain” can be selected in the lower position. During the The software compares the cutting load with the cutting cycle Default. This means that the sawing system can be stopped in the event of irregularities become. • The saw band is cleaned by two adjustable steel brushes. The drive takes place hydraulically. • The hydraulic unit including filter and pressure gauge guarantees one particularly quiet operation at constant pressure. • Finely ground carbide inserts that clamp the saw blade, complete with lateral, hardened and adjustable guide rollers. The adjustable one The tape guide automatically moves as close as possible to the material. • The saw band is tensioned via a hydraulic cylinder, which is carried out by the Machine software is controlled. The voltage is set according to a given Time automatically delimbed when the machine is idle or after a cycle has been carried out. • Automatic version with CNC control in the X-TECH 900 / 1200 models a feed length of 500 mm for the series for high production rates. • The material is carried by a table with seven rollers. These will driven by a hydraulic orbital motor through which the material can be placed precisely even under maximum load. • All guided movements are carried out by four recirculating ball guides with Gbsdofg E Hpepfx Ag Rjg one high capacity for static and dynamic loading; strong reduced feed friction. Tempered and ground prismatic Guides. Price on request.

Condition: new, Year of construction: 2023, Highly efficient series production Clamp – enter the cutting dimension – start. Automatic saws with loading are a standard of rational series processing of bar and bundle material. Cutting area max. up to 290 x 320 mm. Gjdpfofww Sqox Ag Rsbg Furnishing Automatic hydraulic sawing machine with NC control for cutting from 0° to 60° right, complying with all CE safety standards The device has 9 programs, each of which composed of 99 individual steps, with a total number of approx. 890 cutting positions, with corresponding piece counter Function: material feed closing fixed vice Blade rotation, distribution of emulsifiable liquid, temple lowering until the end of the cut and return of the feed carriage until specified amount bail return and stop the blade rotation by cooling liquid distribution cycle repetition Hydraulic feed cut by cut with no length limit Numerical control of quantity and length of cut Hydraulic control center with cutting pressure adjustment The saw blade is tensioned electro-mechanically by means of Microswitch monitored. Device with brush for belt cleaning Bimetallic strip 3200 x 27 x 0.9 mm Section thickness 1.2 mm Material feed stroke 600 mm Motor hydraulic center 0.75 kW Electric pump 0.09 kW to cool the belt It is always possible for you to inspect the desired system in our production/demonstration hall. Please do not hesitate to contact us.

Condition: new, capacity 90 degrees: round 350 mm capacity 90 degrees: square 330 mm 450x320 saw band length 4250x34x1,1 mm band speed 40 + 80 m/min table height 845 mm saw band width 34 mm total power requirement 2,2 kW weight of the machine ca. 0,985 t dimensions of the machine ca. 1,4 x 2,0 x 2,2 m Double miter band saw, hydraulic semi-automatic, DGS 350/450 HA-I · miter left + right 60° without machine conversion · 34 mm saw blade width · Large material support turntable, ball bearings · To position the saw blade guides using a very wide linear guide · Strong, robust transmission · Large chipboards · Infeed and outfeed roller Removable chip tray (disinfection) · Free-standing control panel, safe and ergonomic · Storage space for tapes, consumables · Cutting pressure regulator Feed regulator · Fully hydraulic vise Preload super fast (front loading) · Material height sensor (automatic cut start detection) Semi-automatic function: 1. Clamp material 2. Saw starts 3. Rapid lowering to the start of the material or the same for series cutting cut 4. Saw band off 5. Raise the frame to just above the material 6. Open the vise Optimum, material-independent cutting result through fine adjustment of the saw frame by means of: *Pressure Control Valve (Cutting Pressure Force) *Feed Control Valve (Speed) *Switch with pictogram, easy and clear to use Gbjdpfxefgyico Ag Rjg

Condition: as good as new (ex-display), Year of construction: 2022, pressing force: 320 t, working range: 4,100 mm, Like Baykal 320ton x 4metre Cnc Pressbrake For sale Make: Baykal Capacity: 4metre x 320ton Axis: R and X axis on the back gauge - 2 axis back gauge Year: 2022 Control: Esa S660W Complete with tooling: Multi V lower as well as segmented tooling Gbodpfx Agevgc R He Rsg Technical information: Up to 12mm thickness at 4 meters / Up to 15mm thickness at 3 meters Bending power: 320 tonne 5 axis Bending length (over tooling) 4100mm Bending length (between frames) 3550mm automatic under crowning and laser angle measurement system with live feedback to CNC control for the most accurate folding process

Condition: good (used), Spectro CIROS CCD Water Analyser Gbedpfx Asfiqn Ujg Rsg - height: 105cm - width: 150cm - depth: 75cm Good condition fully functional can be inspected and tested on site. Shipping also abroad. Inspection : Basically I would like to point out that in order to avoid misunderstandings, the article can be inspected and tested under power before purchase. Please ask questions before purchase to avoid any ambiguity. If you have general questions or would like to make an appointment for a viewing, I can be reached at any time at the telephone number below. Errors in the description and prior sale reserved. The value added tax is shown separately on my invoices. Dispatch with forwarding agent.

Condition: new, prebending: 6,0sheet length: 3100sheet thickness: 8,0total power requirements: 11,0weight approx.: 6,7messurements (LxWxH): 4,88x1,16x1,18 Godpfx Ajd Ab H Hjg Rsbg

Condition: new, capacity 90 degrees: round 350 mm capacity 90 degrees: square 330 mm 500 x 310 band speed 15 - 100 m/min table height 844 mm dimensions of saw-band 4250 x 34 x 1,1 mm total power requirement 2,2 kW Gjdpfxjfg E Hlj Ag Rebg weight of the machine ca. 1,2 t dimensions of the machine ca. 1,4 x 2,4 x 1,935 m ACTION PRICE!!! 2-column double miter band saw K-tech DG 50/33 HA-I • 2-column miter saw • Solid, yet easy to use • Material height sensor (automatic cut start detection) • Smooth running thanks to bevel cut, feed controller + cutting pressure controller • Massive material infeed roller • Removable chip tray (disinfection) • Energy-saving and low-vibration thanks to bevel cut • Ergonomic, safe and free-standing control panel • Frequency-controlled saw drive 15 -100 m/min. • Hydraulic cutting pressure control valve • Hydraulic control of saw frame and vice • LEDs for monitoring all safety functions • Large dimensioned wheels (520 mm) a. • Clear miter setting up to 60° Semi-automatic function: 1. Clamp material 2. Saw starts 3. Rapid lowering to the start of the material or the same for series cutting cut 4. Saw band off 5. Raise the frame to just above the material 6. Open the vise

Condition: new, capacity 90 degrees: round 510 mm capacity 90 degrees: square 450 mm 650x450 band speed 15 - 100 m/min table height 844 mm dimensions of saw-band 5320 x 34 x 1,1 mm total power requirement 3,0 kW weight of the machine ca. 2,1 t dimensions of the machine ca. 1,9 x 2,87 x 1,3 m PROMOTIONAL PRICE!!! 2-column double miter band saw K-tech DG 62/45 HA-I • 2-column miter saw Gbedpfjd Iipmex Ag Rsg • Solid, yet easy to use • Material height sensor (automatic cut start detection) • Smooth running thanks to diagonal cutting, feed regulator + cutting pressure regulator • Solid material inlet roller • Removable chip tray (disinfection) • Energy-saving and low-vibration thanks to diagonal cutting • Control panel ergonomic, safe and free-standing • Frequency-controlled saw drive 15 -100 m/min. • Hydraulic cutting pressure control valve • Hydraulic control of saw frame and vice • LEDs for monitoring all safety functions • Large-sized wheels (520 mm) a. • Clear miter adjustment up to 60° Semi-automatic function: 1. Tension the material 2. Saw starts 3. Lowering in rapid traverse to the beginning of the material or the same for series cutting cut 4. Saw blade off 5. Raise the frame until it is just above the material 6. Vice opens