Hydraulic 4-roll plate bending machine

IMCAR 2050 x 6/4 mm

Condition: good (used), Year of construction: 2011, machine/vehicle number: 2212.287, Automatic panelsaw Schelling Typ:FH 6 430 Maskin nr:221.287 År:2011 Panel beam saw Schelling with automatic, rear-feed,lifting table. For sawing board material, chipboard, MDF, Plywood, Board, Laminate etc. Techn info: Software MCS Evolution 2.0, SPS, Soft-SPS-Siemens WinAC Operating system WINDOWS XP PC with keyboard and mouse TFT monitor 17" Cutting length 4300mm, automatic detection of the start of the plate Cutting width 4300mm Machine accuracy of the cut length 3m +-0.1mm Positioning accuracy measured at input +-0.1mm Max diameter saw blade 460mm, spindle 30mm Pre-scoring blade 200mm, spindle 20mm motor operation is set from the control console Max panel thickness 120mm Panel stack aligner Main saw blade motor 27kw Saw blade over table 135mm Safety curtain Air cushion table with 3pcs air ball nozzles, radial ventilator fan Table sizes 2650x850mm 620x850mm 2650x2550mm Pressure beam with automatic adjustment of pressure to cut length and package height Package straightener before and after the pressure beam Max package height 120mm (incl. sum of curvature and board thickness tolerance) Pusher with 12 grippers Max clamp opening (gripper) 133mm Min-max force package straightener 400/2000N Speed saw carriage forward 6-150m/min Speed saw carriage back 150m/min Tedpfx Ajtk It Sjc Tob Forward feed speed (pusher) up to 25m/min (according to EC Europa EN1870-13) other countries 80m/min Speed feeding back up to 80m/min Push-off device 3 pcs Lift table length x width 4350x2550mm Hydraulic unit Standard version 1600mm lifting height 1.25/2.5m/min raising speed, 1.25/5m/min lowering speed Maximum load 1200 kg/m2 total 9 tons Roller track driven rollers, frequency controlled for stack on lifting table 4100x2600mm Max stack weight 6500 kg Max stack length 1060mm Slots for forklift 4 pcs, distance in the middle 1200mm, slot width 300mm Light curtain for personal protection Roller conveyor driven for package frequency controlled input to lifting table left 5600x2600mm max load 6500kg Roller conveyor driven for packages frequency controlled input to lifting table right 5600x2600mm max load 6500kg Slots for forklift 2 pcs, center distance 900mm, slot width 400mm 2 positioning stops with roller for stack alignment Light curtain (double beam) for personal protection Roller table after saw depth 4300mm, free-running ployamide rollers Angle stop at the rolling table Infeed guide two-lane (beam length 7200mm) 2-sided hardened precision guides rack and pinion drive, two-sided Input carriage (pusher) gear rack servo drive, non-contact measuring system Gripper, (scissor clamps) in pusher 12 pcs Automatic adaptation of the clamping force to the package height (progressive clamping force) can be set to 0 Pusher for panels thickness greater than 6mm,material thinner than 6mm is fed manually Central cleaning system feed trough (pusher) Compressed air 6-8 bar, approx. 1600l/min Power 38 kw, 70 A. 3x400 volts, 50 Hz, operating voltage 24 VDC Dust extraction 4000m/h, air speed 30m/s Diameter connection 80mm (angle connection), 120mm /pressure beam), 150mm (sawdust channel) Total setup area without driven roller conveyors including protective grid approx: 11650x7300mm Driven roller tracks left-right 5500+5500mm Stock no: 2002125BXACEO Subject to incorrect technical data presented

Condition: used, Year of construction: 1998, Used DAVI 4-Roller Plate Bending Machine MCB 2020 Technical specifications: Year of manufacture: 10/1998 Manufacturer: DAVI Sheet working width: 2000 mm Sheet bending thickness: 10 mm Pre-bending thickness: 8 mm Roll length: 2050 mm Connections: 400V / 50Hz / 10 HP Tsdpfx Acoy I Uh So Teb Power: 4 kW Surface-hardened 4 rollers Variable bending and rolling speed Safety device with emergency stop switch Digital display of the 4-roller positions on the screen

Condition: new, Year of construction: 2026, functionality: fully functional, type of input current: three-phase, Paint/spray booth dimensions without fan and control Panel! Extraction surface - dimensions (mm): 3000(w)x1900(h) Overall dimension(mm): 3100(w)x2350(h)x1910(d) Technical data: - Fan power 3kW (ATEX) - Fan suction capacity: 16000 m³/h (max 1100Pa) - Lighting: 2 pcs 2x36W (ATEX) - Connection voltage: 400V - Frequency converter for smooth regulation of the fan - Three-stage air filtration - Intended for explosive environments - EX - Complete technical documentation Tsdpfoia Tausx Ac Tob - CE Documentation - Warranty Possibility to order machines in various individual configurations and dimensions! Do not hesitate to contact us.

Condition: new, 3-Roll Round Bending Machine, Ostas ORM 1270 x 140 Technical specifications: Special equipment included in the price: Motorized adjustment of the lower rolls Tsdpjfpmz Hsfx Ac Tob Hardened rolls Motorized adjustment of the rear rolls Digital display Sheet metal width 1270 mm Sheet metal thickness 5.0 mm max. Sheet metal thickness for pre-bending 4.0 mm Roll length 1270 mm Roll diameter 140 mm Weight 1400 kg Dimensions L-W-H 2500 x 800 x 1100 mm Motor: 2.2 kW Equipment: Top and bottom rolls driven by electric motor Top roll can be swiveled out Conical bending device Asymmetrical roll arrangement Self-braking main motor Separate control and operating panel Safety cable CE marking

Condition: good (used), functionality: fully functional, Year of construction: 2015, Four-Roller Plate Rolling Machine Manufacturer: FACCIN Model: 4HEL 2122 Tsdpfxezguums Ac Tob Year: 2015 Technical Specifications Brand: FACCIN Model: 4HEL 2122 Year of manufacture: 2015 Working width: 2050 mm Roll geometry: Linear guides Top roll diameter: 225 mm Bottom roll diameter: 210 mm Side roll diameter: 165 mm Bending force against top roll: 100 t Motor power: 9 kW Dimensions (approx.): L 3.50 x W 1.20 x H 1.10 m Weight (approx.): 4,200 kg Performance Rolling capacity (full working width): 12 mm Pre-bending capacity (full working width): 8 mm From tube diameter: 1,125 mm With yield strength: 260 N/mm² Rolling capacity (full working width): 8 mm Pre-bending capacity (full working width): 6 mm From tube diameter: 295 mm With yield strength: 260 N/mm² Rolling capacity (full working width): 8 mm Pre-bending capacity (full working width): 6 mm From tube diameter: 1,125 mm With yield strength: 360 N/mm² Rolling capacity (full working width): 6.5 mm Pre-bending capacity (full working width): 5 mm From tube diameter: 295 mm With yield strength: 360 N/mm² Rolling capacity (half working width): 15 mm Pre-bending capacity (half working width): 10 mm From tube diameter: 1,125 mm With yield strength: 260 N/mm² Equipment - Double linear guide system for roller movement - Extra wide bearing blocks - MCS double bearing system for roll rotation - Extra heavy-duty, doubly supported drop end bearing - Electronic parallelism system (EPS) - Hardened rolls for maximum wear protection and reduced sheet damage - All rolls polished after heat treatment - SIEMENS S7 PLC touch control - Safety cable with emergency stop and CE certification - Water cooler for hydraulic unit All details without guarantee. A live demonstration under power is possible at any time in our showroom.

Condition: used, Universal Tool Milling Machine MAHO Type MH 800 P with digital readout and HEIDENHAIN TNC 121 contouring control . 80983 Year of manufacture: 1982 Machine overhauled by MMD in 2008, subsequently used only occasionally in the workshop of an electronics company. Travel X: 700 mm, Y: 450 mm, Z: 500 mm Table size: 1050 x 627 mm Spindle taper: ISO 40 Spindle speed: 40–2000 rpm, 18 steps Feed X, Z-axis: 10–500 mm/min, stepless Feed Y-axis: 5–250 mm/min, stepless Rapid traverse X, Z-axis: 1.4 m/min Rapid traverse Y-axis: 0.7 m/min Quill vertical travel: 100 mm Quill feed, vertical: 0.02 / 0.03 / 0.05 / 0.08 / 0.12 / 0.2 mm/rev Quill horizontal travel: 100 mm Spindle drive: 5.5 kW Power supply: 380 Volt, 50 Hz, 10 kW - NC contouring control HEIDENHAIN TNC 121 - Vertical milling head with automatic quill feed 0.02–0.2 mm/rev (6 steps) - Hydro-mechanical tool clamping - Coolant system integrated in the machine base - Universal rotary table, 360° rotatable, tilts and swivels 30°, 225 mm cross adjustment - Rotary table with direct indexing 72 x 5° and indirect indexing via index plate 1:120 = 1 rev = 3° - Swiveling control panel - Central lubrication - Operating manual - Machine mounted on steel plate L x W x H 1400 x 1000 x 50 mm = 550 kg Space requirements L x W x H 2650 x 2000 x 2450 mm Weight: 3700 kg + 550 kg steel plate Total weight: 4250 kg (actual) Tedpfjv Amrysx Ac Tsb Very good condition

Condition: new, Year of construction: 2024, Attention!! Special Offer!! Warranty inspection free of charge—only for Customers who have taken part in the demonstration at the machine showroom in Bydgoszcz. A part of our machines is available IMMEDIATELTY. Manual laser welder 3000 W There are two features that characterize Otinus laser welders - perfectly repeatable welds and ease of use. The kit includes: laser welder with a built-in cooling system welding gun features with a focal length adjustment and a set of accessories MAX Photonics fiber laser source automatic wire feeder lead and hose kit nozzle and lens starter kit Specifications laser power output 1500 W laser wavelength 1064 nm welding speed: up to 120 mm/s feed voltage 230 V 50 Hz dimensions (including the laser head rack) 630x1300x1500 mm Included in the price One-day training along with machine installation 1 day up to 8 hours—machine installation and training. MAX Photonics MAX Photonics was established in 2004. It is rooted in manufacturing light and optics sources for research institutes, where the quality and stability of the products are of paramount importance. The company quickly realized that the future of laser technology is firmly tied to fiber optics. Research and development started in 2007 resulted in the release of their first 500 CW source in 2014. Since then, the company has begun to vigorously develop its technologies related to laser cutting, welding, marking and engraving. 40000W laser sources can be currently found in their offer. The company has set a goal to become a pioneer in the manufacture of high-capacity industrial lasers. Fiber optics connecting the welding gun with the laser source allows the operator to work freely at multiple workstations. Small heat affected zone prevents from severe distortions. The weld is applied in a short time achieving proper and strong joint between materials. Intended use The laser welder is designed for professional use in workshops and plants where high welding quality and aesthetics are required. Laser source output power: 1000 W Carbon steel: up to 3 mm Stainless steel: up to 3 mm Aluminum: 2 mm Todpjrumymofx Ac Teb Brass: 0,8 – 1 mm Laser source output power: 1500 W Carbon steel: up to 4 mm Stainless steel: up to 4 mm Aluminum: 3 mm Brass: 1 mm Laser source output power: 2000 W Carbon steel: up to 5 mm Stainless steel: up to 5 mm Aluminum: 4 mm Brass: 2 mm Laser source output power: 3000 W Carbon steel: up to 8 mm Stainless steel: up to 8 mm Aluminum: 7 mm Principle of operation The laser welder melts down the welding wire together with material edges by means of a laser beam. After switching on and setting up the unit, the welding gun is positioned at the beginning of the future weld line. Then, by pressing the trigger of the welding gun, the beam is generated at the fiber laser source located inside the housing. The beam propagates along the optical fiber to the laser head. The beam is focused and emitted toward the welding wire, which is fed by a wire feeder and toward a location where the gun has been placed. After the trigger is pulled, the head should be pulled along the weld line according to the wire feed rate. The cooling system maintains a constant temperature for the gun and the laser source by means of a water recirculation system. Radiation level and cooling are managed using a controller that adjusts the parameter values according to the user’s parameter settings.

Condition: new, sheet width 1000 mm plate thickness 3,0 mm distance between columns 1050 mm Todpfeyv I Izjx Ac Tjb diameter of upper rolls 90 mm total power requirement 1,1 KW weight of the machine ca. 0,47 t dimensions of the machine ca. 1,7 x 0,8 x 1,35 mm Sheet metal bending machine with custom dimensions: - Capacity 1050 x 3.0 mm - Digital display - Hardened rollers - Conical bending - Swiveling top roller - Brake motor - Safety device: Emergency stop cord - Documentation in English - 400V

Year of construction: 2018, operating hours: 1 h, condition: as good as new (ex-display), machine/vehicle number: 1CY1116D00007, DONALDSON dryer Buran DC 0125 AB with electronic control with electronic level-controlled steam trap Tjdedy Dqkspfx Ac Tjb Technical specifications: Model: BURAN DC0125AB Medium: compressed air, free from aggressive components Flow rate: 2.08 m³ / min Operating pressure: 7 barg Pressure dew point: 3 ° C Compressed air connection: 1 " Electric power supply: 230 V / 50 Hz / 1 phase Frequency: 50 Hz Dimensions, weight Height: 645 mm Width: 360 mm Length: 410 mm Weight: 34 kg

Condition: good (used), Offer 25348 Technical data: - 15 units 300 x 200 x 100 mm - Left and right versions - Total weight approx. 250 kg Todpfx Acjy Nl A Aj Tsb