Roller sets for profile bending machine, 3-roller ring bending machine, standard roller set, profile

HERKULES passend für BO 238 K

Condition: used, Used 3D Printer EOSINT M 270 low operating hours (4910) Giedpfewd Ulvjx Acwjr

Condition: new, Year of construction: 2026, SPIRAL DUCT PRODUCTION MACHINE Metformer MTF 1602 TUBEFORMER Designed for the production of round SPIRO-type ducts. The produced duct complies with DIN EN 12237, BS, and Eurovent standards. Features: Coil decoiler with vertically adjustable brake Forming strips for duct production Burr-free high-speed cutting with circular cutting blades LCD touchscreen control Automatic lubrication system Automatic cutting during duct production Production reporting system (daily-weekly-monthly output) Automatic error detection Technical Data: Diameter range: 80–1600 mm Thickness range: Galvanized steel: 0.4–1.2 mm Stainless steel: 0.4–0.7 mm Aluminum: 0.4–1.3 mm Strip width: For 0.4–1.0 mm thickness: 137 mm For 1.1–1.3 mm thickness: 140 mm Production speed: 60 m/min Motor power: 11.25 kW Beading: Smooth, single or double Lock: External lock Cutting system: Circular cutting system Weight: 2900 kg Machine dimensions: 1900 × 2050 × 1500 mm Decoiler dimensions: 1780 × 1130 × 1250 mm Table dimensions: up to 2700 × 950 × 1200 mm Giodpfx Ajwa Skhjcwjr Operating Environment: Power supply: 3-phase, 380V, 50Hz Clean surroundings Maximum ambient temperature: 40°C Minimum ambient temperature: -5°C Humidity: 55–85% Altitude:

Condition: as good as new (ex-display), Year of construction: 2021, machine/vehicle number: 06 61 218, Comm. no.: Lg 32821 Single side decoiler BBT ABH 2000/400 exhibition machine, unused machine no.: 06 62 218 year of manufacture: 2021 Technical data load capacity approx. max. 2.000 kg Giedpjg U Utvofx Acwor strip width max. 400 mm Coil inner diameter approx. 450 to 520 mm Coil outer diameter max. 1,500 mm Unwinding speed approx. 2 to 15 min.-1 With adjustable drive and loop control via ultrasonic sensor (analog). Drive by frequency-controlled three-phase geared motor. Spreading of the support segments manually by means of hand crank via joints Number of supporting segments 3 Coil side guide via strong limiting arms, clampable. Reel stand in strong box construction as welded design. construction. Additional equipment: Shutdown "belt loop too small" by antenna switch, attached to the column of the bottom housing of the loop control. Infinitely adjustable in height. Tape side guide at the bottom housing of the loop control, by means of lateral guide rods. The passage width is continuously adjustable.

Condition: excellent (used), Year of construction: 2018, laser wavelength: 1,030 nm, power: 5 kW (6.80 HP), Manufacturer: Trumpf Model: TruDisk 5001(6C) Year of manufacture: 2018 Laser power: 5 kW Wavelength: 1030 nm Beam quality: < 100 µm Central sensor interface: yes OEM laser: yes Output power 1: 100% Output power 2: 100% Gedpfx Ajr Izwmjcwoir Output power 4: 100% Beam quality output 1: ≥ 4mm x mrad, ≥ 100µm NA01 Beam quality output 2: ≥ 4mm x mrad, ≥ 100µm NA01 Beam quality output 4: ≥ 4mm x mrad, ≥ 100µm NA01 Active laser power control: yes Live power display: yes Panel computer: yes Processing optics cooling: yes Water connection set: yes Ethernet in user area: multiple Number of occupied fiber links (LLK): 4 Number of intelligent optics: 4 Number of active couplings: 4 Number of couplings: 4 LLK coding (ILN): yes LLK type: LLK-D TLS number: 20-10-03-A105 Additional interfaces: no Parallel interface: yes Interface output 1: Profinet Interface output 2: Profinet Interface output 3: Profinet OPC UA interface: yes VisionLine preparation: yes Number of VisionLine Basic: 2 Number of VisionLine Detect: 0 Number of VisionLine Interface: 1 Number of VisionLine Project: 0 I-PFO preparation: no PFO Smart Teach App: no TLS machine: no TruControl Module Cutassist: no CE/UKCA declaration: Installation declaration with annex

Condition: excellent (used), Year of construction: 2007, operating hours: 53,000 h, functionality: fully functional, machine/vehicle number: 206432, clamping force: 2,000 kN, screw diameter: 50 mm, clearance between the columns: 570 mm, displacement volume: 392 cm³, injection pressure: 2,000 bar, ejector stroke: 225 mm, overall weight: 7,450 kg, Equipment: documentation/manual, Here we, as a dealer in injection moulding machines, are offering the following well-maintained used injection moulding machine: Of course, we also purchase well-maintained injection moulding machines manufactured from 2010 onwards. We have been a wholesaler of used injection moulding machines for over 25 years. Current note – Tax notice and advantage for used machines: As of 01.07.2025, used machines will also be eligible for a special depreciation of 30% annually for tax purposes. Manufacturer: Arburg Model: 520C 2000-800 GE Serial number: 206432 Year of manufacture: 2007 Operating hours: approx. 53,000 Control system: Selogica Dimensions (L/W/H): 5.53 x 1.80 x 2.20 m Weight: 7,450 kg Functional condition: Fully operational Condition: Very well-maintained – German origin Extras: - Thermoplastic cylinder complete, 50 mm, highly wear-resistant - Screw in HC version instead of standard - Selogica direct control - Hydraulic system with 2 variable-displacement pumps - Anniversary model GOLDEN EDITION - Thermoplastic processing - Open nozzle 50 mm - Nozzle tip 50 mm extended - Heating band for open nozzle - Heating band for extended nozzle tip - Central clamping platen set 570, center Ø 125 mm - 2-piece air blast device with pressure regulator - Air blast device connection 1 - Selector unit connection - Core puller 1 for serial motion holding pressure via check valve - Conveyor belt connection via 5-pin socket - Robot interface (per EUROMAP 67), 50-pin - ARBURG host computer interface - Additional socket distributor: 1x CEE, 1x Schuko - Serial printer interface USB - CompactFlash interface for data set storage - Operation authorization with chip card per EUROMAP 65 - 1 additional heating control circuit for nozzle or adapter with socket - Dosing unit interface - Free cooling circuits, manually adjustable - Machine-specific cooling circuits controlled - Extended monitoring package - Extended motion package - Production control package - Optimization / operator assistance package - Quality assurance package - Documentation package Complete documentation included. Injection unit: Screw diameter: 50 mm Shot weight: 359 g/PS Injection pressure: 2000 bar Shot volume: 392 cm³ Clamping unit: Clamping force: 200 t / 2000 kN Tie bar spacing: 570 x 570 mm Mounting plates: 795 x 795 mm Mould installation height: 300 mm Max. platen distance: 950 mm Opening stroke: 650 mm Ejector stroke / force: 225 mm / 66 kN Clamping unit: hydraulic Motor power: 22 kW Heating power: 19.9 kW / 8 heating zones Total connected load: 45 kW The machine is available for immediate delivery at our warehouse in Hannover, Germany and has been tested. Warranty: Warranty until initial commissioning. Loading/shipping: Free loading onto the buyer's truck or free delivery within Germany (freight charge applies) Gedpfx Aew Tt R Iscwsir Available from our warehouse in Hannover, Germany. For your information regarding our machines and company: - We sell only our own machines purchased from ongoing production at our Hannover warehouse. - All listed machines are inspected and tested prior to removal. - We do NOT sell insolvency assets – we are NOT brokers handling third party property. - All offered machines come from successful businesses where proper maintenance is standard practice. - All machines offered are available for viewing at our warehouse.

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Above the sling there are plates with identification holes. Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. Giodpfxofz U S Es Acwor The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators.

Condition: good (used), Year of construction: 2019, functionality: fully functional, total height: 215 mm, total width: 130 mm, total length: 360 mm, overall weight: 7 kg, warranty duration: 12 months, type of cooling: air, product height (max.): 10 mm, welding current at 60% duty cycle: 150 A, welding current at 100% duty cycle: 130 A, welding current (min.): 5 A, welding current (max.): 200 A, - Tested used device in very good condition directly from the manufacturer - - Several devices available - MicorTIG 200 DC ControlPro (Accu-ready) TIG-DC welding inverter with MicorBoost technology (including gas management, high-frequency ignition and electrode welding function). All-in technology for power grid, generator and battery - "3 steps and weld" operating concept - Simple one-button operation - Continuous current setting - Ampere-accurate digital display - With graphical user guidance in the OLED graphic display - Maximum customization thanks to detailed welding sequence control - Job memory for 10 welding tasks Current new price (02/2025): 2,277.00 € plus VAT Scope of delivery: System including removable power cable, carrying strap, gas hose and operating manual THE MicorTIG SERIES. THE POWER PACKAGES FOR MOBILE TIG WELDING. Whether for professional TIG welders or occasional welders: The welding machines in the MicorTIG series from Lorch are the ultimate TIG machines for assembly use, but also for the workshop - suitable for steel and stainless steel. Whether for production or repair, with or without a power socket on site: The MicorTIG series improves the work results of TIG welders around the world - and makes their everyday life easier. Quite literally: At just 6.8 kg, you can easily take your Lorch MicorTIG welding machine with you anywhere - including accessories in the assembly case. Small but powerful: With the patented MicorBoost technology, the welding machines in this series get 200 amps from any normal power socket. INTUITIVE OPERATION. Thanks to the ampere-accurate digital display and clearly structured user interface, intuitive and at the same time very precise operation is possible. Also optionally available: an operating concept using a graphic display. Godpsvxid Rsfx Acwoir NON-CONTACT HF IGNITION. TIG ignition is contactless with high-voltage pulses at the push of a button. Since the tungsten electrode does not touch the workpiece, there are no inclusions in the seam and the electrode is protected. PULSING AND FAST PULSING UP TO 5 kHz. The integrated pulse and fast pulse function up to 5 kHz is particularly suitable for processing thin welding sheets. It enables outstanding melt pool control and perfect results even with difficult welding tasks. JOB MEMORY FOR UP TO 10 WELDING TASKS. With the job function, you can save the parameters of up to 10 welding tasks and call them up quickly when required. Recurring tasks are completed quickly and efficiently. PERFECT FOR ELECTRODE WELDING. Lorch's MicorTIG welding machines are suitable for every electrode type and offer a convenient preselection for CEL and standard electrodes. Even special electrodes are no problem. During welding, the arc force control takes effect and ensures arc stability and perfect material transfer. The anti-stick system prevents the electrode from sticking or burning out. WITH MicorBoost TECHNOLOGY – UP TO 200 A FROM THE SOCKET. The patented MicorBoost technology provides enormous voltage reserves and regulates the TIG arc in an extraordinarily stable, controllable and precise manner – even with fluctuating mains voltage. This allows you to weld with up to 200 amps from a regular socket.

Condition: used, Year of construction: 2020, functionality: fully functional, operating hours: 1,000 h, Kovo Staněk TZNZ 5-11/16-36 (2020) – High-Performance Hanger Shot Blaster Type: overhead rail / hook (CE) • Year: 2020 • Total weight: 12,000 kg • Condition: excellent, production-ready. Capacity & Power Max workpiece: Ø 1600 × 3600 mm (H) Max hook load: 1000 kg Throwing wheels: 5 × 11 kW, rotor Ø 350 mm (individually fed) Abrasive hopper: approx. 1800 kg Air demand: 20 m³/h at 6 bar Noise level: ≤ 85 dB(A) Machine size (W × D × H): 4730 × 5070 × 6520 mm Mains: 400/690 V, 50 Hz • Control voltage: 24 V DC Control & Automation PLC (NX platform) with touchscreen HMI and remote service access. Up to 99 programs with per-job settings: blast time, turbine speed, hook rotation and speed, swing angle of turbine block, servo abrasive flow per wheel, automatic conveyor start/stop. Diagnostics and full interlocking on doors and motions. Wear Protection & Build Blasting chamber lined with XAR500 wear plates (5 mm) and manganese steel X120Mn12 in formed/high-wear zones; replaceable rubber in impact areas. Wheel internals (blades, cages, liners) made from tool steel 1.2379 / X153CrMoV12 (~62 HRC). Heavy welded turbine block housing. Service platform with safety gate and Total Stop. Abrasive Circuit Designed for steel shot S330 (initial charge about 1.5 t). Elevator → air separator → shared hopper loop; magnetic/air cleaning maintains media quality. Servo dosing to each wheel ensures uniform intensity and reduced consumption. Extraction & Filtration CIPRES CARM dust collector, 7.5 kW fan, automatic back-draft flap; ducting includes automatic valve for cabin purge at cycle end. Handling System Powered monorail with adjustable speeds; servo-driven hook rotation and lift; pneumatic diverter switch; two 1.1 kW hoists. Timed sequence allows loading the next batch while blasting. Applications Forgings, castings, welded structures and general steel fabrications—surface preparation before painting, galvanizing or coating with high throughput and repeatable Sa 2½–3 results. Key Advantages 5 wheels for high coverage and speed • PLC plus servo precision • XAR and manganese lining for long service life • 12-ton EU build • Low noise ≤ 85 dB(A). Gisdpsxpiw Uefx Acwer Available for inspection on request via the platform.

Condition: ready for operation (used), machine/vehicle number: 5722, table mounting size: 190 x 710 mm table movement x: 390/360 mm table movement y: 150 mm table movement z: 280 mm spindle taper: SK 40 spindle turning speed range: 100 - 3100 rpm Gsdpfx Aoflrg Tjcweir carriages longitudinal: 0 - 600 mm/min electrical connection: 380 V, ca. 1,5 kW space needed: 1400 x 1200 x 1500 mm weight: ca. 680 kg

Condition: refurbished (used), Year of construction: 2020, machine/vehicle number: PM_1000, Used polishing machine for manual processing. Drive power 5.5 kW Gisdpfx Acjfiugujwsr Polishing discs diameter - 1000 mm