Hera HSS 3100 x 6 mm

Hera HSS 3100 x 6 mm

Year of construction: 1981, condition: good (used), machine/vehicle number: 3626, OFFER 21448 Technical data: - max. working width 2540 mm - max. cutting capacity St 40 4 mm - mot. cutting angle adjustment - cutting gap adjustment by scaled adjusting screws - number of hydraulic hold-downs 14 pcs. - motorized backgauge with positioning stop 10 - 1000 mm - Stroke rate depending on cutting angle and cutting length 23 per/min - hydraulic drive 400 V / 7,5 kW - table height 1030 mm - space requirement approx. W 2500 x H 1630 x D 2150 mm - weight approx. 3600 kg - with: - pneum. supported sheet metal support Pedohhc Ixepfx Aa Ejha - front angle stop + support arms - Electronic cutting depth adjustment - cutting line illumination - E-foot switch

Condition: used, Year of construction: 1999, sheet width 3000 mm plate thickness 3 mm Pedpfxjr Ngtio Aa Eoha 3 support arms 1 angle stop pneumatic hold-down device Backgauge to be operated by hand

Condition: as good as new (ex-display), Year of construction: 2007, I - beam section - flat steel 50 x 10 mm I-beam section - upend 80 x 15 mm L-beam 50 mm round material 30,0 mm bar material dia. max. 1 1/2" mm bar material - diameter 30,0 mm weight 0,185 t range L-W-H 670 x 530 x 1350 mm square material 40 x 40 x 3 mm pipes 60 x 2,0 mm total power requirement 0,75 kW Demonstration device Equipment: • Base frame of the machine • Foot switch • Standard-rolls (divided) Phedpfxet U R H Ue Aa Eea • Possible to bend horizontally and vertically

Condition: like new (used), functionality: fully functional, Year of construction: 2016, operating hours: 10 h, Includes: Special iron turning tool ATRC 18 Special scroll bending tool ATAR 305 Spiral bending device ATSC Demonstration machine, no 10h worked! TECHNICAL DATA Shaft diameter mm. 30 Roller diameter mm. 128 Roller revolutions per minute rpm. 8.5 - 17 Pedpfx Aet Akxasa Esha Drive motor Kw. 0.75 Main switch with release coil and built-in emergency (CP30 - CP30 R) - Reversing gear and double speed switch are mounted on a separate console (CP30 - CP30 R) - Foot switch Foot switch rotation control L/R with built-in emergency - (CP 30 PR) - Two-speed selector (CP 30 PR) - Mechanical regulation of the upper roller Mechanical regulation of the upper roller with position reading on display - Two traction rollers with ribbed surface Internal machine body made of steel - Steel shafts steel shafts, hardened and ground - Gear wheels made of special special steel with ground teeth - Rollers made of special steel with a hardness of 59/60 HRC - Outer cover in ABS - Working position horizontal (CP 30) Horizontal working position (CP 30) - Horizontal and vertical working position vertical (CP 30 R - CP 30 PR) Weight: CP 30 PR 240 kg. External dimensions mm: CP30 PR Base 680 x 800 - Height 825 ACCESSORIES Straightening rollers with two positions - Universal rollers ( standard ) - Operating key Operating key - Operating instructions

Condition: excellent (used), Year of construction: 1997, pressure 170 t chamfer lenght 4080 mm distance between columns 3680 mm column arm 410 mm dayligth 385 mm Phedpfx Aasxcp Rbs Eja stroke 215 mm ajustment speed 200 mm/sec working feed 1-10 mm/sec return speed 135 mm/sec table width 200 mm table height 1050 mm Number of working hours 25.430 h oil volume 350 l total power requirement 29 KVA weight of the machine ca. 16.450 kg. range L-W-H 4620 x 2210 x 2885 mm Machine in good condition Regularly serviced by the manufacturer CNC backgauge with 8 axes (!!) - in checked conditions - machinevideo - ?v=yEaRj0XJAC4 Equipment: - CNC electro-hydraulic press brake/die bending press - DELEM CNC control - swiveling front left * High-resolution graphic screen * Clear, concise menus in the operator's language * Large tool and product library * Graphic 2D programming * Automatic bend sequence calculation and collision detection * Emergency stop button at front - CNC axis adjustment: * Y1 - Y2 - X1 - X2 - R1 - R2 - Z1 - Z2 axis + CNC crowning - X axis - adjustment speed: 500 mm/sec. * Max. stop range: 860 mm - R axis - Adjustment speed: 300 mm/sec. * Max. travel: 250 mm - Z axis - Adjustment speed: 1000 mm/sec. * Max. travel: 3260 mm - CNC electric motor table crowning - CNC electro-pneumatic die shift (I axis) - WILA / TRUMPF upper tool clamping - hydraulic - WILA / TRUMPF lower tool clamping - hydraulic - 2x front, robust support arms - movable - 1x freely movable 2-hand/foot control - 1x freely movable foot switch - Side safety device (swivel doors) - Rear safety device (sliding doors) - Original operating instructions

Condition: good (used), Brand Ercolina Model CE40H3 Year of manufacture 2006 Hydraulic drive Roller diameter Ø 165 mm Shaft Ø 40 mm Tube capacity (thin-walled) Ø 70x1.5 mm min. Ø 700 mm Tube capacity (thick-walled) Ø 2" x 3.2 mm min. Ø 450 mm Psdpfx Asw Hx Tvja Ejha Angle section capacity 50x50x6 mm min. Ø 400 mm Flat bar capacity 50x10 mm min. Ø 250 mm Flat bar capacity (hard edge) 100x15 mm min. Ø 250 mm Box section capacity 50x50x3 mm min. Ø 500 mm Shaft capacity Ø 35 mm min. Ø 250 mm Power 1.85 kW Bending speed 10 rpm.

Condition: new, Year of construction: 2023, functionality: fully functional, power: 114 kW (155.00 HP), fuel: diesel, Equipment: documentation/manual, type plate available, The REMKO "CLK 120" heating cannon is a powerful heater suitable for use in warehouses, workshops, marquees, materials, greenhouses, and more. Currently, 3 units are immediately available from stock. Condition: New / unused from warehouse clearance / insolvency Scope of delivery: Phsdpfxexgbbto Aa Eea - 1 Remko CLK 120 heating unit with oil burner - 1 Roth mobile heating oil tank 1000 L - 1 room thermostat with connection cable Rated heat load: 114 kW Air output: 8050 m³/h Fuel: heating oil EL Fuel consumption: max. 11.2 L/h Flue gas loss: max. 9% Flue gas connection: Ø 200 mm Air outlet: Ø 500 mm Connection voltage: 230 V Dimensions (H/W/D): approx. 1350 x 920 x 2100 mm Weight: approx. 296 kg The machine can be viewed on site by appointment. All information without guarantee. Subject to prior sale.

Condition: new, capacity 90 degrees: round 305 mm capacity 90 degrees: square 260 mm 350x200 saw band length 3375x27x0,9 mm band speed 18 - 100 m/min table height 880 mm total power requirement 1,5/1,8 kW weight of the machine ca. 0,84 t dimensions of the machine ca. 1,85 x 1,9 x 2,0 m Demonstration system for a SPECIAL PRICE!! Fully automatic miter band saw • miter left 45° automatic operation • miter left 60° semi-automatic operation (cuts without programming) • Material height sensor (automatic cut start recognition) • Frame and gear made from one piece, very quiet cut and very low vibration • Removable chip tray (disinfection) • Shockproof and ergonomic control panel with oil-resistant EPDM cover • Top access to the saw, material and feed unit • Hinged safety cover • Fine feed adjustment Pjdeupw R Ajpfx Aa Ejha • Semi-auto. Cut! • Optimize work processes with CNC control Possibility to enter various parameters such as quantities and material lengths, automatic calculation of the cutting channel • CNC control for 10 different saw programs with 99 sub-programs for different lengths and quantities, e.g. 1 cutting program with various section lengths • Automatic feed unit (CNC) via ball roller spindle incremental feed with automatic length compensation. Adjustable for section lengths of 2 mm to 9,999 mm, remainder length 170 mm. Inclusive: - Micro-spray device - Leveling elements

Condition: used, functionality: fully functional, EUROMAC MULTI 220/6R NOTCHING MACHINE Phedpfx Aaswqdfxe Esa Maximum cutting length 220 mm Maximum sheet thickness 6 mm Variable cutting angle 30 - 120 WITH PUNCHING MACHINE EUROMAC Multi 220/6R 2-station notching and bending machine Press brake, press brake, cutting machine Cutting capacity steel from 6 mm to 45 kg/mm2 Becu Akmemck Ryo Iswn 4 mm for stainless steel Station I (notching) Notching angle from 60° to 140° (with special knives from 30° to 140°) Knife length 220 mm Table dimensions 950 x 640 - manual angle adjustment by handwheels - Notching angle with built-in knife set from 60° to 140° - hydraulic knife locking upper and lower - automatic cutting gap adjustment - Blank holder - Measuring tapes built into the table - Stop guides with angle adjustment - Operation via foot switch Station II (die bending device) Pressure force 18 tons Table dimensions 950 x 340 Working height 1100 mm - Regular lifting speed - Continuously adjustable stroke limiter - Stroke adjustment up to 30 mm working stroke - Reversible prism with 4 prisms 90°, length = 415 mm - Upper tool 90°, length = 415 mm Motor power 4kW Mains connection 400 volts, 50 Hz OVERALL DIMENSIONS 115X100X125 WEIGHT: 900 KG

Condition: used, Drilling machine, column drilling machine, pillar drilling machine, pillar drilling machine, multi-spindle head, multi-spindle drilling head, drilling gear -with two-spindle drilling head Manufacturer Sigloch Schrieder Type: V602 -Drive power: 1.02/0.88 kW -Drill distance adjustable: 18-110 mm -Max. Drill: 2x Ø 6 mm -Table size: 275 mm -Spindle mount: MK3 -Projection: 220 mm -Speeds: 100-2900 rpm -Columns: Ø 100 mm -Spindle stroke: 75 mm -Transmission -Dimensions: 900/400/H1910 mm -Weight: 230kg Phedoc Rpnnepfx Aa Eja