Cut to length machine

FORSTNER COMPACT

Condition: good (used), Offered is a used double toggle jaw crusher from Krupp. Good condition, fully operational. 500 x 300 mm, 15 kW, new tools. The motor is currently being overhauled. Gijdpfx Afewy U Iconen

Condition: new, 900 mm 900 mm 900x900 mm saw band length 9300 x 67 x 1,1 mm table height 790 mm band speed 14 - 60 m/min total power requirement 11 kW weight of the machine ca. 8,45 t dimensions 4,485 x 1,68 x 3,15 m The semi-automatic, hydraulic saws from the X-tech line offer the best Saw technology and best performance when cutting special steels • The electro-welded machine frame and the steel saw frame meet requirements all cutting needs and eliminate vibration and noise. • The chip conveyor is hydraulically driven and the speed is adjustable • All movements of the machine (saw frame, vice, feed, Saw band guides) are carried out thanks to modern linear guides with high static and dynamic load performance, which also has very low sliding friction to guarantee. • Another characteristic feature is the roles for the Positioning of the material by a hydraulic motor are driven. They move at right angles to the material, and thus allowing optimal clamping of the material. • Thanks to the height control of the saw band position, the operator can place the band in place near the top edge of the material. After the cut is finished, the tape automatically raised back to the previous position. Alternatively you can also “Remain” can be selected in the lower position. During the The software compares the cutting load with the cutting cycle Default. This means that the sawing system can be stopped in the event of irregularities become. • The saw band is cleaned by two adjustable steel brushes. The drive takes place hydraulically. • The hydraulic unit including filter and pressure gauge guarantees one particularly quiet operation at constant pressure. • Finely ground carbide inserts that clamp the saw blade, complete with lateral, hardened and adjustable guide rollers. The adjustable one The tape guide automatically moves as close as possible to the material. • The saw band is tensioned via a hydraulic cylinder, which is carried out by the Machine software is controlled. The voltage is set according to a given Time automatically delimbed when the machine is idle or after a cycle has been carried out. • Automatic version with CNC control in the X-TECH 900 / 1200 models a feed length of 500 mm for the series for high production rates. • The material is carried by a table with seven rollers. These will driven by a hydraulic orbital motor through which the material can be placed precisely even under maximum load. • All guided movements are carried out by four recirculating ball guides with one high capacity for static and dynamic loading; strong reduced feed friction. Tempered and ground prismatic Guides. Giedpfjfg E Hpsx Afnsn Price on request.

Condition: used, SLITTING LINE GEORG 1500x1.5x25 Main technical data Coil thickness: 0.24 – 1.5 mm Uncoiler coil weight: 25 Tn Coil width: 230 - 1500 mm Coil outer diameter: Max. 1850 mm Working speed: 200 m/min Slitting tolerance: +/- 0.125 mm Line direction: Right to left Recoiler coil weight: Max. 16 Tn 2 Slitting heads PLC: Siemens S7 1200 Cutting capacity: number of cuts with 350 MPa 24 cuts for thickness 0.25 mm 28 cuts for thickness 0.50 mm 21 cuts for thickness 0.75 mm 18 cuts for thickness 1.00 mm 15 cuts for thickness 1.25 mm 12 cuts for thickness 1.50 mm Scope of supply Giodpfjxl R A Rjx Afnen 1. Coil Carriage 2. Uncoiler 3. Guiding system with 2 measured edges 4. 203.2 diam. Pinch roll before shear 5. Double interlock table 6. Slitting shear:Shaft diameter: 160 mm 7. 1 off line quick change slitting head available 8. Scrap press and conveyor 9. Intermediate coil table 10. Loop Pit and covering tables 11. Strips Braking Unit 12. Motorised recoiler with hold down separator arm 13. Unloading Coil Car 14. 4 arms turnstile 15. Electrical cabinets & Control panels 16. Existing tooling 17. Existing documentation Coil thickness: 0.24 – 1.5 mm Uncoiler coil weight: 25 Tn Coil width: 230 - 1500 mm Coil outer diameter: Max. 1800 mm Working speed: 200 m/min Slitting tolerance: +/- 0.125 mm Line direction: Right to left Recoiler coil weight: Max. 16 Tn Slitting heads: 2 PLC: Siemens S7 1200 For thickness 0.25 mm: 24 cuts with 350 MPa For thickness 0.50 mm: 28 cuts with 350 MPa For thickness 0.75 mm: 21 cuts with 350 MPa For thickness 1.00 mm: 18 cuts with 350 MPa For thickness 1.25 mm: 15 cuts with 350 MPa For thickness 1.50 mm: 12 cuts with 350 MPa

Year of construction: 2002, condition: reconditioned (used), Beam cutting, drilling and marking line DISC SAW Brand: KALTENBACH Model: HDM 1431 / T13 / SP-CNC Year 2002 Serial number: 122.400 Weight without accessories: 10,980kh - Disc saw with downward cut. - Geared saw unit, drive system and saw blade on wear-resistant swivel bearing. - Heavy saw gear with pinions in oil bath, with inclined teeth, hardened and sharp. - Hydraulic advancement of the saw blade, adjustable according to the table, very fast recoil. - Hydraulic horizontal clamping device. Rear clamping jaw with long-stroke clamping cylinder and automatic recoil limitation. - Vertical clamping block with self-adjusting push plate. - Oblique cutting device to adjust the angle from 45° to the left to 35° to the right. - Material sensor to automatically switch from rapid advance to work advance. - Hydraulically elevating feed roller for optimum material transport on the saw table. - Economical lubrication by means of a micro-dosing installation, especially suitable for sawing profiles. - Chip collector installed on the machine bench. Specs: - Cutting disc housing: 100x4x30x250mm - Cutting disc diameter: 1,430mm - Cutting width: 9.5mm - Cutting speed: 10 to 20m/min. - Saw advance speed: 0-400mm/min. - Fast reverse speed: 2000mm/min. - Total power: 25KW - Working height: 640mm Cutting capacities: 90º cut - Angle steel: 250mm - Steel in U: 400mm - Double T-beam: 600mm - Wide flanged beam: 1008x302mm - Special wing beams: 1000x450mm Cut to degrees: IPBv beam - 75º: 1008x302mm - 60º: 910x302mm - 45º: 716x304mm - 40º: 716x304mm - 35º: 478X307mm IPBs beam - 75º: 1008x402mm - 45º: 524x357mm IPE beam - 45º: 600x220mm DRILLING UNIT Brand: Kaltenbach Model: KDX1215 Serial number: 122.401 Work capabilities: - Angular steel (minimum - maximum): 80x65x10mm - 250x250x28mm - Steel in U (minimum - maximum): 80x45mm - 400x110mm - Double T beam (minimum - maximum): 80x46mm - 600x220mm - Wide flanged beam (minimum - maximum): 100x100mm - 1,008x302mm - Extra wide wings beam: 1,200x500mm Drilling units: 3 - Vertical (Y axis) 1 pc. - Horizontal (Z and W axes) 2ud. Drilling diameters: 8 - 40mm RPM: 150 - 1100 Fast forward - Fast reverse: 3,850mm/min. - 8,000mm/min. Drilling spindle feed rate: 0-500mm/min. Fast spindle positioning tool: 15,000mm/min. Automatic tool changer: 5 u. in each drilling unit. 3x5 u. = 15 total Total power: 45KW MARKING UNIT FEEDING: Giedpfshzbipox Afnon 26 METERS OF ENTRY WITH BEAM FEEDER + 6 SIDE ARMS FOR BEAM ENTRY IN PARALLEL TO THE ROLLER TRACKS 30 METERS OF ROLLER TRACKS WITH OUTPUT + 6 SIDE ARMS 4 SIDE ARM FOR SMALL PIECES THE GREAT MAJORITY OF ROLLERS ARE MOTORIZED It occupies approximately 60 linear meters between input and output power. *Request machine installation plans.

Condition: new, Year of construction: 2025, OSTAS PRE-MACHINERY TYPE KM 1,2 - Capacity 1,2 mm Gjdpfxogg Nrko Afnsin - Unloading 250 mm - With 8 sets of rolls CALL FOR MORE INFO DUTCHMACH Metalworking machines ENSCHEDE

Condition: new, Year of construction: 2025, Capacity 2020 x 2 mm (ST37) Delivery of the upper beam by hand lever left + right Slanted segments in the upper beam Continuous bending and lower beam rails Gijdpfsfifa Ajx Afnon RAL 7016 paint Manufacturing EU immediately available ex works Freight costs on request

Condition: good (used), A.Saint 1500 x 2 mm cutting line, I have more photos on my website Gsdpfx Afjiihp Senein

Condition: new, Year of construction: 2026, CIDAN Machinery manufactures coil handling slit and cut-to-length lines that can be programmed and operated by skilled and non-skilled users alike. Our cut-to-length machines are all-in-one units built to withstand high-level production over the course of time while taking up as little space as possible. CIDAN Machinery provides many of their cutting-edge features as standard – straightening units, sheet guide for in-feeds, guillotine shears with hold down beam and double-edged blades, feeding units, foot pedals for remote feeding, and many more. In order to provide the absolute best technological options from around the globe, CIDAN Machinery has partnered Forstner Machinery, a world-wide leader in slit and cut-to-length machines Since 1960, Forstner has been developing and manufacturing machines for professional coil processing. Our partnership has provided us the opportunity to bring all of their best machines to you! - Sheet metal on coils saves money, reduces waste and frees up storage space. - We have the right solution for all levels of production. - Free up floor space with coil processing and increase your productivity and your profits. Godpfxsmfrgrj Afnsin - The extensive range of Forstner products can be combined to make an efficient production facility based on your requirements, where parameters such as power, distance, time and access to material are decisive for fast and cost-effective production. - With our solutions you can easily process coils from 500 kilos up to 8 tons. Bigger coils mean fewer changeovers, less waste and a more efficient process. - How many different materials do you need readily accessible? Frequent changeovers? With a coil selector you keep eight different materials ready at the cut-to-length for far quicker changeovers. - With a well equipped cut-to-length in your production facility you will no longer need to cut strips in guillotine shears. - Do you sell sheets or do you want to recoil material in smaller coils? We have the right solution for you! - Rational coil handling cuts your lead times, frees up production space and reduces tied up capital in stocks.

Condition: excellent (used), Knuth UFM 2 universal milling machine Technical data X-axis travel (manual) 800 mm X-axis traverse path 750 mm Traverse path Y-axis 300 mm travel Z-axis 400 mm table size 1320x320 mm T-slots 5x14x63 mm Feeds Y-axis travel (8) 20 - 360 mm/min Z-axis travel 600 mm/min Gsdpenfu Risfx Afnjin Spindle speed (12) 58 - 1800 min-1 Vertical spindle taper SK 40 Distance between spindle tip and table 0 - 400 mm Head rotation 45 Cone of horizontal spindle SK 50 Drive Main motor power 4 kW motor power in Z axis 0,75 kW feed motor power 0,55 kW cooling pump motor power 0,09 kW Coolant pump capacity 25 l/min Dimensions and weight dimensions 1900x1720x1750 mm weight 2100 kg Financing through our bank is also possible. komplett-konzept.leasingo.de Further articles - new and used - you will find in our store! International shipping costs on request!

Condition: new, Year of construction: 2025, BIEGEMASTER double bender - Model XBend 6.1,25 Effective length: 6400 mm Bending capacity Steel 400 N/mm²: 1.25 mm V2A 600 N/mm²: 1.00 mm Aluminum 190 N/mm²: 2.00 mm Clamping capacity (closed seam): 0.5 mm steel Number of uprights: 4 pieces Driven upper bending joints: 4 pieces Driven bending joints bottom: 4 pieces Incl. touchscreen CNC control with automatic depth stop Incl. electric shears BIEGEMASTER Up- and Down- Bending machine - model XBend 6.1,25 Working length: 6400 mm Bending capacity steel 400 N/mm²: 1.25 mm stainless steel 600 N/mm²: 1.00 mm aluminum 190 N/mm²: 2.00 mm Hemming capacity (closed hem): 0.5 mm steel Stands + Tension Arms: 4 pcs. Driven linkage joints upper beam: 4 pcs. Driven linkage joints down beam: 4 pcs. Incl. touchscreen control and automatic back-gauge Gijdpfxsvhc Dpo Afnen Incl. electric cutter