Drilling Table

federhenn 84.24K021

Condition: used, Year of construction: 2023, DOUBLE GLASS BEAD SAW TRF 527 VIS CE 1 pc DOUBLE GLASS BEAD SAW TRF 527 VIS CE TRF 527 VIS: Double miter saw for the simultaneous cutting of two glass beads positioned one above the other. The right saw unit is fixed, adjustment of the left unit is via the set cutting length can be read off a digital display. The units have supports that allow two glass beads to be cut simultaneously. The upper support can be removed for cutting larger cross-sections. After the cutting process is completed, the pneumatic clamping cylinders automatically swing to the side to simplify loading and unloading of the machine. STANDARD EQUIPMENT • Fixed unit on the right • Digital dimension display • Pressure switch • 2 HM-tipped saw blades • Electrical system with motor brake, undervoltage release, motor protection switch • Pressure switch • Tool set • Guards with horizontal clamping devices, pivoting • Two-hand control • Belt drive • Pneumatic unit lift • Middle support TECHNICAL DATA • Motor power 2 x 1.2 kW • Saw blade diameter Ø 220 mm • Max. cutting height without support 80 mm • Max. cutting width at 90 degrees 55 mm • Max. cutting width at 45 degrees 40 mm • Max. cutting length 2800 mm (optional 4000 mm) • Min. cutting length 158 mm • Weight 217 kg • Space requirement (standard equipment) 3000 x 850 mm Extended cutting capacity 1 pc Maximum cutting length • 4000 mm Star stop 4 positions 1 pc set 2 mechanical stops for adjusting up to 4 intermediate angles. Additional center support. 1 adjustment for rebated profiles. 1 adjustment for rebated profiles as per drawing: - Attachment to the clamping devices to compensate for the profile inclination - Allowances on the rear stops of the units and the center support. The sketch below shows (in green) a beveled presser that follows the inclined profile and presses it against the allowance on the stop (shown in red). Ncodpfsxnlgcsx Amnot Storage location: Garbsen

Condition: refurbished (used), Year of construction: 2024, Manufacturer: Elumatec Type SA/ SAS 142 Overhaul year: 2024 Saw blade max. carbide: 500 mm Drive power saw motor: 4 KW Saw motor speed: 2800 min-1 Cutting speed saw blade 500 mm: 4400 m/min Saw height control: infinitely variable, fully electronic Working range square 90° max.: 130 x 130 mm Working range flat: 90° max.: 190 x 130 mm Working range round: 90° max.:150 mm Pneumatic feed length: 5-560, 10-1120 mm Compressed air connection, on site 6 bar Weight(saw)approx.: 800 kg Dimensions LxWxH (saw)approx.:2900mm x 1400mm x 1500mm Installation area LxW: 2900mm x 1400mm Additional description Elumatec SA/ SAS 142 4KW Retrofit Elumatec SA 142 4KW Retrofit Fully automatic sawing machine for non-ferrous metal and plastic After completion of the retrofit, the machine is in mint condition, both technically and visually. The machine will be overhauled in our company at the customer's request. Among other things, the following points were renewed: - Conversion to Siemens S7 PLC control - Conversion to Siemens HMI control panel - New electrical components - New pneumatic lines - Maintenance or replacement of all pneumatic cylinders and valve terminals - Maintenance of minimum lubrication system - Replacement of general wear parts - Overhaul of the cab Warranty: Unless otherwise agreed, we provide a 6-month warranty on all parts overhauled or replaced by us. Working time and wearing parts are excluded from the warranty. Optional: Nsdpfsuiy Nysx Amnsct - Extension of the sawing area to flat 90° max.: 300 x 120 mm - Splitting extension (for a high-quality cut surface without return marks) - Servo-controlled material feed - Saw blade feed Servo-controlled - Mass clamping device Feed vice - Delivery and installation on your premises - Training of your employees

Condition: refurbished (used), Year of construction: 2010, XXL-Center RAS 75.06 - General technical data in mm: Bending length: 6400 mm Max. sheet thickness (400N/mm2): 1.5 mm Max. sheet thickness (750N/mm2): 1.0 mm Max. sheet thickness (200N/mm2): 2.0 mm Gripper claws travel range: 10 – 750 mm Clearance in front of the jaws up to: 300 ° Extendable loading tables: yes Gripper claws: yes Programming: automatic via Bendex Machine dimensions incl. safety fence approx.: 9400 x 3000 Ncjdpfx Aox Hf Tvsmnst Weight: 12.5 tons - Machine-specific data: Motor-driven; 400V, 50/60 Hz, 3-phase Year of manufacture: 2010 Condition: Will be completely overhauled - Images are examples -

Condition: used, Year of construction: 2020, Overview  This complete microbrewery system was manufactured in 2020 by German company Sudhausbau GmbH. The installation is a 5 hl, steam-heated, two-vessel brewhouse including milling, hot side, control system, steam generator, fermentation, storage, water treatment, cooling and accessories. The system is well maintained and comes with a functional guarantee upon delivery. Technical data  Brewhouse capacity: 5 hl Design: 2-vessel brewhouse Heating: Steam-heated Control: Semi-automatic PLC (Siemens) with touch panel Fermentation: Open fermenters with cooling jackets Scope of Delivery Malt Mill with Stand & Hopper | — | — | 2020 | For brewhouse feeding Brewhouse (Mash/Kettle + Lauter Tun) | Sudhausbau GmbH | — | 2020 | 5 hl, steam-heated, incl. platform & piping Plate Heat Exchanger | — | — | 2020 | Single-stage, stainless steel plates (1.4404) Water Mixing Station | — | — | 2020 | Solenoid valve, mixer, meter Brewhouse Control System | Siemens (PLC) | — | 2020 | Semi-automatic, recipe control Steam Generator | — | — | 2020 | Gas-fired, incl. water treatment, TÜV & CE Open Fermenters (2x) | Speidel | — | — | 625 L each, with cooling jacket Horizontal Storage Tanks (5x) | — | — | — | 500 L each Hot Water Tank | — | — | — | 700 L, insulated, electric heater Cold Water Tank | — | — | — | 700 L, insulated, cooled Water Cooler | — | BL 040 | — | 1.8 kW, cooling & heating function Fermentation Temperature Controllers (3x) | Cube Plug | — | — | — Mobile Pump | — | — | — | — Brewery Accessories | — | — | — | Beer hoses, kegs (30 L & 50 L), misc. parts Optional: Cold Room with Refrigeration Unit | — | — | — | Single-wall, no cooling jacket   Nsdpfxex Nm Sxj Amnjct

Condition: new, Year of construction: 2026, functionality: fully functional, machine/vehicle number: SÇ 901 S Pnömatik Alüminyum Köşe Presi Makinası, - Conforms to CE standards - Corner press machine designed for 90 degree joining of aluminum profiles - 2 top presses and blade movement is pneumatic - There is a mm ruler system for the height and advancement of the blades. - Centering miter wedge is automatic Nedpfx Amorbiv Ajnjct - Drain button available for fine adjustment - Pneumatic presses use 2 pedals to squeeze the profile - Profile surfaces are polyamide sheet to prevent damage - Side support arms available

Condition: good (used), Year of construction: 2019, machine/vehicle number: 24451.19, Offer 25359 Technical Data: - Cutting capacity at 90° (round): 250 mm Ncodpfx Amsxup Rfenet - Cutting capacity at 90° (flat): 275 x 180 mm - Miter adjustment to the left - Cutting capacity at 45° (round): 200 mm - Cutting capacity at 45° (flat): 190 x 180 mm - Cutting capacity at 30° (flat): 130 x 110 mm - Material support height: approx. 920 mm - Saw band dimensions: 3100 x 27 x 0.9 mm - Infinitely variable cutting speed: 15 to 100 m/min - Hydraulic lifting and lowering of the saw frame - Upper travel limit of the saw frame - Infinitely adjustable cutting pressure: 0 – 10 m/min - Hydraulic material vice - Micro-spray cooling system - Total drive power: 400 V / 2.2 kW - Required space approx.: W 2400 x H 1600 x D 1800 mm - Weight approx.: 1300 kg - 3 x Roller conveyor, each 1500 mm

Condition: used, Year of construction: 2004, 10 spindle system. Connected load: 380/400V/50Hz, 34 kW. Glass thickness: 3-60 mm. Nedswynzcopfx Amnoct

Condition: used, Year of construction: 2007, functionality: fully functional, Machine for drilling holes for dowels URBAN DB 3100, year 2007 Ncjdpfxewinq No Amnet Condition: very good - Profile clamping system and drill feed operated by foot switch - Electric drilling motor switches off automatically at the end of the drilling process - Drill feed speed and drilling depth individually adjustable - Quick-clamp chuck for standard drill bits up to max. Ø13mm - Left and right support tables

Condition: new, Vacuum lifter BARBARIC B3 swiveling, incl. crane - Exhibition unit - Including: - Vacuum lifter BARBARIC uniWood UWL 3, 150 kg Vertical and horizontal transportation of flat commercial commercially available boards (coated boards, natural wood panels) up to a panel size of 3,000 x 2,100 mm - a tilting range of 90° with pneumatic tilting mechanism - Complete with hoist and corresponding safety devices safety devices (vacuum manometer and manual manual slide valve with mechanical safety device) - uniWood traverse with 2 suction pads Ø 270 mm on an adjustable traverse (traverse length: 1,500 mm) Includes: - Optional reinforced BARBARIC uniWood version for easily permeable boards Load capacity: 250 kg with 2 oval suction pads 500 x 250 mm on an adjustable cross beam (cross beam length: 1,250 mm) and reinforced vacuum pump for permeable sheets. The reinforced design enables lifting materials weighing up to 250 kg. Includes: - BARBARIC uniWood comfort operation option All controls for the lifting gear and for the vacuum the vacuum lifter are integrated in one control unit - our special handling handle is accommodated. This makes it possible to operate the system and guiding the load in one-handed operation. The lifting process can be steplessly controlled by a frequency converter. The comfort version comes complete with hoist and corresponding safety devices (vacuum pressure gauge and 2-button safety control for releasing the load). Includes: - BARBARIC column-mounted slewing jib crane Lifting capacity on the lifting device: 250 kg The lifting capacity is the specified working load on the lifting device. Barbaric slewing jib cranes are designed for handling tasks in all areas of application and are extremely Nedpju R Szaofx Amnect lightweight. SSK consisting of column, bracket and smooth-running jib. jib. Slewing and trolley travel by hand. The prerequisite for attachment is a suitably concrete floor (C20/R5, min. 20 cm). The static inspection of the floor must be carried out on site and documented accordingly. For fastening on cracked concrete or less load-bearing substrate, we offer enlarged base plates enlarged base plates on request. Fastening: Supplied with adhesive anchor for concrete floor When ordering without lifting gear, please specify the cable or hose type! Delivery includes: incl. sliding trolley, power supply and compressed air connection. - new exhibition machine -

Condition: new, Year of construction: 2026, Fully automatic cutting of medium-large aluminium profiles with simple-to-use automation. Put down any aluminium profile, the machine will automatically detect it and cut it into jobs tasked with high-accuracy servo motor material positioning. Excel job lists WIFI input for streamlined input of large cutting lists. For every piece of aluminium you place down to cut, no matter what length, a laser sensor measures its length. Our powerful optimisation algorithm on-the-fly calculates the best order of parts to produce minimum waste. The machine automatically cuts the calculated list without stopping. No need for any inputs from you, just keep putting in new aluminium stock. Simple, high-speed alternative to double-headed saws. Just enter (or import) the lengths and angles you need and press GO. The machine continuously produces your angled parts, accurately and at high speed. • Fully-automatic cutting operation with bar feeding and cutting to length. • Simple user interface for automatic operation, enter job and cut in seconds. • Simplified part, batch, or large excel lists job cutting. Nsdpfof Ekn Djx Amnoct • Bundled / multi-bar cutting and counting. • Remote WIFI excel job lists input with extensive data mapping capabilities. • Fully adjustable saw cutting and timber feeding rates for maximum process productivity. • Automatic optimiser mode with timber laser length measure and optimisation for minimum waste (optional). • Automatic labels printing for parts using data from the job list (manual label application, optional). • Inline direct-to-material printing with no operator action required (optional). • Bar codes or QR codes printing or scanning for jobs input (optional). • Automated servo positioning of the saw mitre angle up to ±75° (optional). Highly suitable for: • Windows and doors manufacture • Mitered aluminium structures manufacture • Aluminium fabricated structures manufacture • Composites manufacture • Blinds, shades and furniture manufacture • Aluminium retail sales Model: A550 Length: 6 m Linear Unit: ProfiStop Alpha Material Length: 4680 mm Pushing capacity: 20 - 40 kg Software: Optimiser QUALITY AUSTRALIAN-MADE MACHINES.