Fasti 509-30-6

Fasti 509-30-6

Year of construction: 1981, condition: good (used), machine/vehicle number: 3626, OFFER 21448 Technical data: - max. working width 2540 mm - max. cutting capacity St 40 4 mm Ndsdpohhc Ixsfx Aa Esf - mot. cutting angle adjustment - cutting gap adjustment by scaled adjusting screws - number of hydraulic hold-downs 14 pcs. - motorized backgauge with positioning stop 10 - 1000 mm - Stroke rate depending on cutting angle and cutting length 23 per/min - hydraulic drive 400 V / 7,5 kW - table height 1030 mm - space requirement approx. W 2500 x H 1630 x D 2150 mm - weight approx. 3600 kg - with: - pneum. supported sheet metal support - front angle stop + support arms - Electronic cutting depth adjustment - cutting line illumination - E-foot switch

Condition: used, Year of construction: 1999, sheet width 3000 mm plate thickness 3 mm 3 support arms Noder Ngtispfx Aa Eedf 1 angle stop pneumatic hold-down device Backgauge to be operated by hand

Condition: used, Year of construction: 1985, sheet width 2500 mm plate thickness 6 mm rear stop 750 mm down holder 16 Stk total power requirement 12 kW weight 5400 kg dimensions of the machine ca. 3000 x 1500 x 2000 mm Equipment: - Electric backgauge 750 mm - Pneumatic sheet metal holders Njdpfxst Sykqj Aa Esdf - 2x side stops - 3x front support arms - Ball rollers in the front support table - Rear sheet metal chute - Foot switch

Condition: used, Hydraulic Plate Shear LVD Type HST-C 31 / 6 Machine No. 21348 Year of manufacture: 1994 Cutting length: 3,100 mm Cutting thickness: 6.35 mm Backgauge: 770 mm Working height: 950 mm Hydraulic sheet hold-downs: 17 units Hydraulic tank capacity: 150 liters Motor power: 7.5 kW Power connection: 400 Volt, 50 Hz, 9.5 kW, 19 Amp. - Motorized backgauge with digital actual position display ELGO - Backgauge adjustment via push button – rapid in both directions and fine adjustment by jogging in the minus direction only - Sheet lifting device below the backgauge with pneumatic lifting cylinder - Continuously adjustable blade gap from 0.1 mm via handwheel with analog display - Cutting angle adjustment in 5 steps from 1.5° to 3.5°, electrically pre-selectable - Left side angle stop 1,500 mm - 2 table extensions as sheet supports - Electric foot switch - Comprehensive operating manual Space requirements without front table extension (L x W x H): 4,150 x 1,850 x 1,900 mm Ndsdpfx Aetvb Iusa Eef Space requirements with front table extension (L x W x H): 4,150 x 2,850 x 1,900 mm Weight: 5.5 tons Good condition Very good cutting results, including with thin sheet metal

Condition: good (used), Year of construction: 1991, Sheet width 2500 mm Sheet thickness 4 mm Cutting angle 1.49 ° Strokes per minute 40-80 Ndjdetq S T Nepfx Aa Ejf Stand projection 200 mm Number of hold-down devices 13 pieces Backgauge - adjustable 5-1000 mm Table height 750 mm Oil capacity 85 l Air pressure - required 5 bar Machine weight approx. 3600 kg

Condition: excellent (used), Year of construction: 1997, pressure 170 t chamfer lenght 4080 mm distance between columns 3680 mm column arm 410 mm dayligth 385 mm stroke 215 mm ajustment speed 200 mm/sec Ndjdexcp Rbjpfx Aa Ejf working feed 1-10 mm/sec return speed 135 mm/sec table width 200 mm table height 1050 mm Number of working hours 25.430 h oil volume 350 l total power requirement 29 KVA weight of the machine ca. 16.450 kg. range L-W-H 4620 x 2210 x 2885 mm Machine in good condition Regularly serviced by the manufacturer CNC backgauge with 8 axes (!!) - in checked conditions - machinevideo - ?v=yEaRj0XJAC4 Equipment: - CNC electro-hydraulic press brake/die bending press - DELEM CNC control - swiveling front left * High-resolution graphic screen * Clear, concise menus in the operator's language * Large tool and product library * Graphic 2D programming * Automatic bend sequence calculation and collision detection * Emergency stop button at front - CNC axis adjustment: * Y1 - Y2 - X1 - X2 - R1 - R2 - Z1 - Z2 axis + CNC crowning - X axis - adjustment speed: 500 mm/sec. * Max. stop range: 860 mm - R axis - Adjustment speed: 300 mm/sec. * Max. travel: 250 mm - Z axis - Adjustment speed: 1000 mm/sec. * Max. travel: 3260 mm - CNC electric motor table crowning - CNC electro-pneumatic die shift (I axis) - WILA / TRUMPF upper tool clamping - hydraulic - WILA / TRUMPF lower tool clamping - hydraulic - 2x front, robust support arms - movable - 1x freely movable 2-hand/foot control - 1x freely movable foot switch - Side safety device (swivel doors) - Rear safety device (sliding doors) - Original operating instructions

Condition: new, capacity 90 degrees: round 305 mm capacity 90 degrees: square 260 mm 350x200 saw band length 3375x27x0,9 mm band speed 18 - 100 m/min table height 880 mm total power requirement 1,5/1,8 kW weight of the machine ca. 0,84 t dimensions of the machine ca. 1,85 x 1,9 x 2,0 m Demonstration system for a SPECIAL PRICE!! Fully automatic miter band saw • miter left 45° automatic operation • miter left 60° semi-automatic operation (cuts without programming) • Material height sensor (automatic cut start recognition) • Frame and gear made from one piece, very quiet cut and very low vibration • Removable chip tray (disinfection) • Shockproof and ergonomic control panel with oil-resistant EPDM cover • Top access to the saw, material and feed unit • Hinged safety cover • Fine feed adjustment • Semi-auto. Cut! • Optimize work processes with CNC control Possibility to enter various parameters such as quantities and material lengths, automatic calculation of the cutting channel • CNC control for 10 different saw programs with 99 sub-programs for different lengths and quantities, e.g. 1 cutting program with various Nodpfoupw R Aox Aa Esdf section lengths • Automatic feed unit (CNC) via ball roller spindle incremental feed with automatic length compensation. Adjustable for section lengths of 2 mm to 9,999 mm, remainder length 170 mm. Inclusive: - Micro-spray device - Leveling elements

Condition: new, Year of construction: 2023, functionality: fully functional, power: 114 kW (155.00 HP), fuel: diesel, Equipment: documentation/manual, type plate available, The REMKO "CLK 120" heating cannon is a powerful heater suitable for use in warehouses, workshops, marquees, materials, greenhouses, and more. Currently, 3 units are immediately available from stock. Condition: New / unused from warehouse clearance / insolvency Scope of delivery: - 1 Remko CLK 120 heating unit with oil burner - 1 Roth mobile heating oil tank 1000 L Ndedpjxgbbtefx Aa Eof - 1 room thermostat with connection cable Rated heat load: 114 kW Air output: 8050 m³/h Fuel: heating oil EL Fuel consumption: max. 11.2 L/h Flue gas loss: max. 9% Flue gas connection: Ø 200 mm Air outlet: Ø 500 mm Connection voltage: 230 V Dimensions (H/W/D): approx. 1350 x 920 x 2100 mm Weight: approx. 296 kg The machine can be viewed on site by appointment. All information without guarantee. Subject to prior sale.

Condition: ready for operation (used), Year of construction: 1984, sheet width 3040 mm plate thickness 4 mm distance between columns 3040 mm stroke of upper beam 200 mm adjustment of lower and bend clamping 100 mm total power requirement 6,4/3 kW weight of the machine ca. 6,3 t dimensions of the machine ca. 4,3 x 1,2 x 1,8 m Motorized folding machine with double-sided bending beam drive, lower, upper and bending beam adjustable, drive motors as brake motors - slip clutches as overload protection, bending angle adjustment via potentiometer, operating modes: individual switching for each work step and sequence control for the complete work cycle, SEGMENTED TOP RAIL 120 mm height (Photo 7). As usual, the sheet thickness is based on a strength of 40 kg / mm². Nodexwzbbspfx Aa Eodf Machine dealer with own stock of 2500 m².

Condition: good (used), Year of construction: 2009, sheet width 3050 mm plate thickness 6.0 mm cutting angle adjustment 0.5 - 3.0 ° down holder 18 Stück no. of strokes 8 - 14 Hub/min back stop - adjustable 750 mm work height max. 770 mm Control SP 8 total power requirement 7.5 kW weight of the machine ca. 4800 kg. range L-W-H 3650 x 2100 x 1750 mm very little use (!!) from a maintenance workshop Ndedpfjxmakgsx Aa Eef Features - Guide-railed electro-hydraulic guillotine shear - HACO control model NC SP 8 * Easy operation directly at the cutting table * Adjustment of cutting angle + backgauge * Retraction function from rear stop * Electric cutting length limitation * Emergency stop button, locking - Motor-adjustable and programmable rear stop - Electric/hydraulic cutting angle adjustment - Manual cutting gap adjustment, from the front - 1x side stop - 1,000 mm, with scale & T-slot - Front finger guard - 1x freely movable foot switch - Rear safety guard + sheet metal chute - Operating instructions (PDF)