Tool milling machine

Deckel FP1

Condition: reconditioned (used), Year of construction: 1976, Universal Tool Milling Machine Manufacturer: DECKEL Model: FP 1 Year of manufacture: 1976 – workshop inspected Machine No.: 51720/08 Geometric acceptance with inspection protocol Accessories: - 3-axis digital readout K+C Arbah-M, new - Fixed table 600 x 210 mm (T-slot 12 mm) - Vertical milling head SK 40 Hodpfx Afoyipmwenonh with draw thread S 20 x 2 - Coolant system - Operating manual Used as seen, without warranty The machine technically corresponds to the standard at the time of manufacture.

Condition: used, Year of construction: 1990, x-travel 400 mm y-travel 330 mm z-travel 350 mm total power requirement 6,3 kW weight of the machine ca. 2 t dimensions of the machine ca. 736 m Hnodpfxet Hxbwe Afneh

Condition: used, tool adaptor 88 length 560 mm Hjdjv Dxzcepfx Afnjnh center height of top slides 65 mm weight 17 kg Counter holder / horizontal milling device for tool milling machine Deckel Mod. FP 1 consisting of upper beam and mounting of the milling arbor. The distance from the middle of the milling arbor to the lower edge of the counter holder is 65 mm, the width of the guide is 88 mm. Machine dealer with own stock of 1600 m².

Condition: used, Universal Milling Machine DECKEL FP1 Travel X: 300 mm Travel Y: 150 mm Travel Z: 300 mm Horizontal + vertical spindle Cone SA40 DECKEL Spindle speed: from 40 to 2000 RPM Table size: 600 x 210 mm Horizontally tiltable head Hnsdsxxpp Nepfx Afnoh Straight table Spindle motor: 2 speeds Motor: 1,3 kW Feeds: X - Z auto / Y manual Voltage: 380 V Width: 1200 mm Depth with electrical panel: 1200 mm Height:1600 mm Weight: approx 900 kg

Condition: used, Universal Tool Milling Machine DECKEL Type FP 1 Machine No. 51265 Year of manufacture: approx. 1967 Travel paths X: 300 mm Y: 150 mm Z: 340 mm Hnjdpfxjghtvao Afnjh Table size 600 x 200 mm Spindle taper SK 40 - S20 x 2 Spindle speed 40–2000 rpm, 16 steps Motor power 1.0 and 1.6 kW, pole-changing Power supply 380 Volt, 50 Hz - Feed on X and Z axes - Spindle speed via 2 motor speeds and 8 gear steps - Quill movement at vertical milling head 60 mm - Swiveling, rotating, and tilting angle table - Coolant pump in machine base - Separate control cabinet Space requirements L x W x H 1100 x 1100 x 1600 mm Weight 690 kg In good condition

Condition: used, Universal Milling Machine DECKEL FP1 Travel X: 300 mm Travel Y: 150 mm Travel Z: 300 mm Horizontal + vertical spindle Cone CM4 DECKEL Spindle speed: from 40 to 2000 RPM Horizontally tiltable head Hedpfx Aoxyymbsfnsnh Spindle motor: 2 speeds Motor: 1,5 kW Feeds: X - Z auto / Y manual Supplied without table only with one 4 concentric jaws Ø 140 mm Voltage: 380 V Width: 1200 mm Depth: 1200 mm Total height: 1600 mm Weight: approx 900 KG

Condition: used, Year of construction: 1982, x-travel 300 mm y-travel 160 mm z-travel 340 mm feeds -stepless- 5-500 mm/min rapid traverse 1200 mm/min spindle turning speed range 40 - 2000 U/min tool taper Normkegel 40 table length 600 mm table width 120 mm voltage 380 V Hedpfx Aovvnfuefnenh frequency 50 Hz rated current 13 A weight of the machine ca. 0,750 t dimensions of the machine ca. 1,8 x 1,5 x 1,8 m DESCRIPTION Machine incl: active three-axis digital readout HEIDENHAIN documentation various tool holders Machine vice etc.

Condition: refurbished (used), Year of construction: 2025, functionality: fully functional, machine/vehicle number: 211031, Country of manufacture: Switzerland Voltage: 380/50/3 Net weight: 740 kg Overall dimensions: 155 x 110 x 160 cm Installed power: 2.10 kW Customs tariff number: 8459.6930 Hnedpfxow Uc Npj Afnsh TECHNICAL SPECIFICATIONS Vertical rectangular table: - usable surface: 740 x 200 mm - number of T-slots: 2 - width of T-slots: 12-H7 - distance between slots: 120 mm Fixed right-angle table: - usable surface: 700 x 250 mm - number of T-slots: 5 - width of T-slots: 12-H7 - distance between slots: 40 mm - possible lateral movement: 250 mm total Universal tilting table: - usable surface: 600 x 210 mm - number of T-slots: 4 - width of T-slots: 12-H7 - distance between slots: 40 mm - possible lateral movement: 350 mm total Adjustable in 3 planes, on either side: 30°-45°-30° Spindle internal taper: - horizontal spindle head: ISO 30 (40) - vertical spindle head: ISO 30 (40) - universal rapid head: SV E20+ES20 Swivel in vertical plane: vertical spindle head: 360° Longitudinal travel, hand/automatic: 320/300 mm Vertical travel, hand/automatic: 375/355 mm Cross travel, adjustment handle: 150 mm Quill stroke: 60 mm Readout accuracy on micrometer verniers: 0.02 mm Main motor power/speed: 1.5 kW/1500 rpm Rapid feed motor power/speed: 0.45 kW/3000 rpm Coolant device motor power/speed: 0.15 kW/3000 rpm Spindle speed range: - 1st range: 58-375 rpm - 2nd range: 330-2000 rpm Feed rates (longitudinal or vertical): 12-400 mm/min - 10 feed rates, mm/min: 12-18-26-38-57-85-125-185-270-400 Rapid traverse speed (longitudinal or vertical): 1200 mm/min All technical data is given without obligation and subject to errors or omissions.

Condition: excellent (used), Year of construction: 2000, Machine-Details: Stock-No. 1022-2416 Type of machine Tool Room Milling Machine - Universal Make DECKEL Type FP 1 Year of manufacture 2000 Type of control conventional Storage location Monheim (Germany) Country of origin Germany Delivery time Immediately Freight basis Ex warehouse, loaded on truck Technical details: Hnsdoyhdbmspfx Afnoh x-travel 300 mm y-travel 160 mm z-travel 290 mm table surface area 600 x 210 mm tool taper SK 40 spindle turning speed range (16) 40 - 2000 U/min feeds -stepless- 5 - 500 mm/min rapid traverse 1,2 m/min spindle motor 1,5 / 1,9 kW total power requirement 9,5 kVA weight of the machine ca. 830 kg dimensions of the machine ca. 2000 x 2200 x 1655 mm Additional information: The machine is in very good condition and comes from a training workshop. Equipment: * 3-axis positioning control with active digital display Heidenhain TNC 123 - Manual mode: Manual operation and positioning with manual input - Automatic mode: Single-block programme run, programme storage * Fixed angle table * Movable vertical milling head, swivel range +/- 90 degr., quill stroke 60 mm * Coolant equipment * Central lubrication * Tailstock with counter bearing * Manual

Condition: good (used), Internal article no.: 26022 Universal milling machine Deckel FP1 + Accessories (machine vice / dividing attachment / SK40 tool holders / tailstock) An M16 drawbar is installed in the milling head Hnedpfx Ajxxkwnjfneh + Additionally, S20x2 drawbar The machine can be inspected under power.

Condition: good (used), functionality: unexamined, machine/vehicle number: 10279, turning diameter over cross slide: 200 mm, spindle bore: 35 mm, turning diameter: 300 mm, center height: 150 mm, turning length: 750 mm, total length: 1,860 mm, total width: 700 mm, total height: 1,800 mm, spindle speed (max.): 2,800 rpm, spindle speed (min.): 40 rpm, overall weight: 1,030 kg, - Operating voltage: 380 V - Connected load: 3 kW - Nominal current: 25 A - Frequency: 50 Hz Equipment: - Tailstock - Multifix type B tool holder Hnodpfov Irgtsx Afnoh - Three-jaw chuck (diameter: 160 mm) - 2-axis digital display from the manufacturer RSF

Condition: reconditioned (used), Year of construction: 1984, functionality: fully functional, travel distance X-axis: 300 mm, travel distance Y-axis: 150 mm, travel distance Z-axis: 340 mm, quill stroke: 80 mm, spindle speed (max.): 2,000 rpm, spindle speed (min.): 40 rpm, table length: 210 mm, table width: 600 mm, total height: 1,750 mm, total length: 1,400 mm, total width: 1,600 mm, rotational speed (max.): 2,000 rpm, rotational speed (min.): 40 rpm, overall weight: 850 kg, table load: 200 kg, warranty duration: 3 months, The machine underwent a factory or partial overhaul by us in 2026 and is in top condition. As part of the partial overhaul, a new brake motor was installed. Control System 3-axis – active – digital display HEIDENHAIN TNC 113 Spindle Speed 40–2000 rpm, geometrically stepped direct drive with 18 speed levels for maximum torque and milling performance Feed Rate 5 to 500 mm/min, infinitely adjustable Rapid Traverse 1.2 m/min Quill Extendable quill, vertical 80 mm SK40 with M16 drawbar thread, optionally with DECKEL saw thread S20 x 2 Extendable quill, horizontal approx. 100 mm Axes X/Y/Z 300/150/340 mm Table Fixed angle table 600x210 mm Hnsdpfx Afsyi Amwonjh Maximum table load: 200 kg Features • Vertical and horizontal spindle • Milling head manually swivelable +/- 90° • Z-axis bellows Options • Chip tray • Machine lamp • Universal table • Rotary table • Slotting head • Dividing head • Steady rest • etc.

Condition: excellent (used), Year of construction: 2002, Control: 3-axis active path control, Heidenhain TNC 123 Spindle speed: 40 - 2000 rpm, geometrically stepped direct drive with 16 gear stages for maximum torque / milling performance Feed rate: 5 to 500 mm/min, infinitely variable Rapid traverse: 1.2 m/min Quill: Extendable vertical quill, 60 mm, SK40 M16 draw thread Hedpfxsyg I Nfj Afnenh Axes X/Y/Z: 300/160/340 mm Swivel table: 600 x 210 mm, max. load 200 kg

Condition: good (used), Please read the technical specifications in full. If you are considering the machine as an investment, we kindly request your complete identification, including a valid telephone number and email address, in order to provide you with an offer. DECKEL Tool Milling Machine FP 1 No. 2101 with HEIDENHAIN 3-axis digital readout Travel distances: X/Y/Z: 300 x 160 x 340 mm Manual adjustment of the milling head arm: 100 mm Expansion of working area to: 300 x 260 mm Spindle speed vertical/horizontal: 40 – 2,000 rpm Number of gear stages: 16 Spindle taper: SK 40 Tool clamping: S20 x 2 (Deckel standard) Quill travel: 60 mm Feed X/Z-axis: 5 – 500 mm/min Feed adjustment: stepless Rapid traverse X/Z-axis: 1200 mm/min Feed Y-axis: manual Fixed angular table: 600 x 210 mm Hsdpfx Aoxyc Tkefnjnh Swivelling vertical head: +/- 90 degrees Weight: 710 kg Dimensions: approx. 1250 x 1200 x 1850 mm Technical data are not binding! Features: - For horizontal machining, the milling head is swiveled by 90 degrees and pushed backwards. - 3-axis precision digital readout HEIDENHAIN - Stepless feed in X/Z axis - The machine underwent partial overhaul by a specialist company several years ago. Equipment: - 3-axis HEIDENHAIN digital readout - Micro-cooling spray unit - Fixed angular table - Chip tray - Machine lamp - Machine feet Further accessories available upon request! Condition: good to very good, from training workshop Available from March 2026

Condition: good (used), Year of construction: 1985, Taxed according to the differential taxation scheme under §25a of the German Value Added Tax Act. You will receive a proper invoice. Internal item no.: 26006 You are welcome to inspect the machine under power in our heated warehouse area of over 500m². Universal milling machine Deckel FP1 (3-axis active digital) Year of manufacture: 1985 Travel distances: X300 / Y160 / Z340 mm Quill stroke: 60mm Connected load: 1.9 kW Number of spindle speeds: 16 Hsdpfeygv Upex Afnonh Speed range: 40-2000 rpm Tool holder: SK40 Feed: infinitely variable 5-500 mm/min The control system works perfectly, but the LEDs are defective! + Hydraulic machine vice Röhm BB110 The machine comes from an educational institution and is in well-maintained condition.