Single Column Press - Hydraulic

Calende Einständerpresse

Condition: refurbished (used), Year of construction: 2018, machine/vehicle number: DF0150, pressing force: 63 t, pressure:63 t passage width:700 mm Pedpofhcc Usfx Ampjgk stroke:500 mm Approx. weight (w/o operational materials):5,1 t Measurements L x W x H:ca. 1500 x1600 x 2995 mm Return Capacity:6 t Engine Output:11 kW Max Working height:700 mm Approaching Speed max. :140 mm/sec Pressure Speed:15 mm/sec. Travel:500 mm Ram plate:600 x 540 mm Table size:750 x 600 mm Table height above ground level:850 mm Oil Tank Capacity:150 l Control voltage:24 V Frequency:50 Hz Siemens Control System:S7 1200 Monitor:Siemens 12 Zoll Special feature: When operating at 260bar the machine reaches a pressure level of 70 tons.

Condition: good (used), Make: OMERA Type: R4 / 12-2 Year: 1976 Table length : 1900 Table width : 1000 Steady arm throath HOR : 670 Steady arm throath VER: 940 Stroke cylinder : 350 Column diameter : 200 Specifications Metric US Standard There are no specifications for this machine (yet). Dimensions (Estimate) Length 3000 mm Width Psdpfekvnumox Ampogk 2200 mm Height 2500 mm Weight 2800 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: refurbished (used), Year of construction: 2019, machine/vehicle number: DF0195 - Rev.00, pressing force: 40 t, pressure:40 t passage width:850 mm stroke:500 mm Weight of machine approx.:ca. 3,8 t dimensions:ca.1300 x 1800 x 3200 mm return capacity:4 t pestle plate:600 x 450 mm table plate:750 x 720 mm table height over floor:850 mm Oil cooling (electric):1,5 kW (max) max. working heidht:700 mm motor capacity:12,7 kW Approaching Speed max. :140 mm/sec pressure speed:15 mm/sec Return Speed:140 mm/sec Oil Tank Capacity:160 l Pgedefhcc Hspfx Ampjk Monitor:WEG - 10 Zoll Siemens Control System:S7 1200

Condition: as good as new (ex-display), Year of construction: 2018, machine/vehicle number: DF0151 - Rev.00, pressing force: 110 t, pressure:110 t passage width:800 mm stroke:500 mm Approx. weight (w/o operational materials):5 t Measurements L x W x H:ca. 1950 x 1510 x 3145 mm Return Capacity:11 t Engine Output:20 kW Pedpfx Aedxrqwsmpogk Cylinder diameter:200 mm Max Working height:700 mm Approaching Speed max. :195 mm/sec Pressure Speed:1 - 15 mm/sec. Return Speed:5 - 140 mm/sec Travel:500 mm Ram plate:800 x 600 mm Thickness of ram plaet:6 Zoll Table size:800 x 700 mm Table height above ground level (approx.):900 mm Oil Tank Capacity:400 l Program Memory:200 prgms Monitor Siemens:10 Zoll Siemens Control System:S7 1200 Lightcurtains by Schmersal:700 mm Speed controlled via proportional valve for speeds between 5 to 195 mm/sec on approach, 1 to 15 mm/sec during pressure phase and 5 to 140 mm/sec during return. HMI - pressure regulation for capacity of hydraulic cylinder from 20 to 110 tons Siemens remote access for maintenance purposes Motor with energy efficiency level IE3 according to CE

Condition: new, New hydraulic high speed press from min. 300t up to max. 2500t. We offer new mechanical and hydraulic presses for various applications, individually tailored to your needs. Give us your requirements and we will make an attractive offer with installation and service. ISGEC has delivered to more than 26 countries in recent years, including Thailand, Indonesia, Vietnam, USA, Germany, Spain, France, Brazil, Hungary, Mexico, Bangladesh and over 200 presses to 40 Japanese customers. We are proud to be official sales partner since 2020 and look forward to hearing from you. Pgsdpfsf Rt Irex Ampok

Condition: new, Year of construction: 2019, pressing force: 110 t, pressure:110 t stroke:400 mm weight of the machine ca.:4,5 t dimensions:ca. 1650 x 1150 x 2800 mm return capacity:11 t total power requirement:11 kW Max Working height:500 mm :10 mm :10 mm/sec. speed rapid traverse:10 mm/sec Psdefxygtepfx Ampogk :400 mm pestle plate:600 x 500 mm table plate:800 x 700 mm Table cut-out:150 x 150 mm table height over floor:900 mm :250 l Monitor SIEMENS:7 Zoll Side trim:2.800,- ? :4.800,- ? Light barriers front and back:2.400,- ?

Condition: as good as new (ex-display), Year of construction: 2021, machine/vehicle number: 06 61 218, Comm. no.: Lg 32821 Single side decoiler BBT ABH 2000/400 exhibition machine, unused machine no.: 06 62 218 year of manufacture: 2021 Technical data load capacity approx. max. 2.000 kg strip width max. 400 mm Coil inner diameter approx. 450 to 520 mm Coil outer diameter max. 1,500 mm Pgjdpfxjg U Utvo Ampek Unwinding speed approx. 2 to 15 min.-1 With adjustable drive and loop control via ultrasonic sensor (analog). Drive by frequency-controlled three-phase geared motor. Spreading of the support segments manually by means of hand crank via joints Number of supporting segments 3 Coil side guide via strong limiting arms, clampable. Reel stand in strong box construction as welded design. construction. Additional equipment: Shutdown "belt loop too small" by antenna switch, attached to the column of the bottom housing of the loop control. Infinitely adjustable in height. Tape side guide at the bottom housing of the loop control, by means of lateral guide rods. The passage width is continuously adjustable.

Condition: used, Eccentric punch press HAULICK + ROOS type RVD 125 Pgedpfjhlnzkjx Ampek double column - eccentric press Machine No. 212560 Year of construction 1981 pressure force 125 ton. table size 880 x 800 mm table opening 470 x 140 mm column width 900 mm column width lateral 415 mm ram stroke 45 mm slide adjustment travel 0-80 mm Installation height on the picture 340 mm Stroke rate 50 to 300 strokes/min. Motor power main drive 22 kW Mains connection 380 volt, 50 Hz - Double connecting rod drive with 4-fold eccentric shaft for off-center ram pressure load - adjacent electrical cabinet - NC roll feed EBU, width 250 mm, year 2003 - adjacent control panel for roll feed - strip running direction from left to right space requirement (press) L x W x H 3000 x 2000 x 3020 mm transport height 2950 mm weight of the press approx. 11 ton.

Condition: good (used), Year of construction: 2000, turning diameter 340 mm turning length 2000 mm control FAGOR 8055 swing diameter 550 mm spindle bore 108 mm spindle turning speed - stepless 2500 U/min power capacity 16.5 kW quill stroke 220 mm diameter of quill 100 mm total power requirement 19 kW weight of the machine ca. 4300 kg dimensions of the machine ca. 4300 x 1600 x 1800 m This EMCO E 300x2000 cycle lathe is supplied complete with all accessories. Description: - Coolant device - 1 piece Luenette open 20-145mm - 1 piece closed guide 15-185mm - 1 piece face plate Podpfxsvwgpbj Ampjgk - 1 piece three-jaw chuck - 1 piece wedge bar chuck D=400mm - Parat 4-fold tool holder - Various tool holders

Condition: new, Year of construction: 2026, -Custom-Made Machines Tailored to Your Production Needs. -Our custom-made machines are meticulously designed and engineered to meet the unique demands of your production processes. Whether your focus is finishing, oxide removal, or radius edge rounding, these machines deliver outstanding precision and performance -Finishing: Achieve smooth, high-quality finishes on a wide range of materials, ensuring a consistently professional, polished appearance. -Oxide Removal: Effectively eliminate surface oxides to provide a clean, contaminant-free surface—essential for further processing or coating applications. -Radius Edge Rounding: Precisely round edges to your specified radius, enhancing both safety and the overall quality of your finished products. Customization Options Each machine is tailored specifically to your requirements, offering flexibility in: Processing Speeds: Adjustable to match your varying production demands. Special Features: Options include dust and fume extraction systems, adjustable pressure settings, and programmable configurations designed to optimize your workflow Pjdpfxehq Dbxo Ampjgk Built for Durability. Constructed with longevity in mind, our custom machines are built to perform reliably through extended production cycles. Whether for small-scale projects or high-volume industrial applications, these machines provide exceptional results, year after year