Aluminium Circular Saw

BERG & SCHMID MultiCut 401 HA

Condition: used, Year of construction: 1966, shaft length 15 - 130 mm wire diameter 6 - 12 mm length of wire blank max. 170 mm capacity/output with closed mould, adjustable 100 /min Nedjv Sva Ejpfx Aa Ejdf capacity/output with open mould, adjustable 67 /min Weight 12,5 t dimensions of the machine (WxDxH) 2,3 x 4,0 x 1,6 m combined double-pressure cold header press for jaws and closed moulds maximum wire diameter for high tensile bolts und carriage bolts 10 mm maximum wire diameter for mild steel bolts and rivets 12 mm wire diameter range 6 - 12 mm minimum and maximum shaft length 15 - 130 mm maximum length of wire blank 170 mm capacity/output with closed mould, adjustable - 100 St/min capacity/output with open mould - 67 St/min power requirement 15,0 kW mould dimensions - jaw dimensions 54 x 54 mm

Condition: new, saw blade diameter 400 mm capacity 90 degrees: round 130 mm capacity 90 degrees: flat 160 x 130 mm capacity 45 degrees: round 110 mm capacity 45 degrees: flat 110 x 125 mm saw blade turning speeds 3000 U/min total power requirement 1,75 kW weight of the machine ca. 140 kg dimensions 1,0 x 0,65 x 1,5 m Alu miter saw Ndjdpfx Aeuay Dlsa Ejf - Miter left/right 45° - pneumatic double clamping device - with mist spray device - with machine base - Roller conveyor 3m with material stop - Machine feet

Condition: new, capacity 90 degrees: round 350 mm capacity 90 degrees: square 330 mm 450x320 saw band length 4250x34x1,1 mm band speed 40 + 80 m/min table height 845 mm saw band width 34 mm total power requirement 2,2 kW weight of the machine ca. 0,985 t dimensions of the machine ca. 1,4 x 2,0 x 2,2 m Double miter band saw, hydraulic semi-automatic, DGS 350/450 HA-I · miter left + right 60° without machine conversion · 34 mm saw blade width · Large material support turntable, ball bearings · To position the saw blade guides using a very wide linear guide · Strong, robust transmission · Large chipboards · Infeed and outfeed roller Removable chip tray (disinfection) · Free-standing control panel, safe and ergonomic · Storage space for tapes, consumables · Cutting pressure regulator Feed regulator · Fully hydraulic vise Preload super fast (front loading) · Material height sensor (automatic cut start detection) Semi-automatic function: 1. Clamp material 2. Saw starts 3. Rapid lowering to the start of the material or the same for series cutting cut 4. Saw band off 5. Raise the frame to just above the material 6. Open the vise Optimum, material-independent cutting result through fine adjustment of the saw frame by means of: *Pressure Control Valve (Cutting Pressure Force) Ndedpfxjfgyics Aa Eof *Feed Control Valve (Speed) *Switch with pictogram, easy and clear to use

Condition: good (used), Year of construction: 2008, machine/vehicle number: 21100122-F, Offer 25108 Technical Data: - Saw blade dimensions 350 x 3.4 x 32 mm - Saw blade speed 3400 rpm - Cutting range at 90° round 120 mm - or flat 105 x 105 mm - 180 x 70 mm - at 45° round 110 mm - flat 135 x 60 mm - Bevel adjustable left + right 45 ° - Tiltable bevel adjustment of the saw head for ship cuts left - Pneumatic vises Nsdpfx Aaewq N Swe Eedf - Discharge – roller conveyor with length stop 2000 mm - Feed – roller conveyor 3000 mm - Drive 400 V / 2.2 kW - Space requirement approx. W 600 x H 1730 x D 1200 mm - Weight approx. 180 kg

Condition: new, Year of construction: 2021, functionality: fully functional, surgical mask line, high speed surgical mask line, Food Pad, wound pad, mask line The 3-ply surgical mask line , wound pad, mask production system offered here combines efficiency and safety features with a first-class meat pad, food pad, fruit pad . The integrated extra module "Single Pack" enables the food pad production machine to pack each mask individually wrapped at full speed of up to 800 pads / min. The film rolls also have an autosplice function, so that the system weld the film together on the fly while unit operation. Surgical mask line can be used as following outer layer Spunbond nonwoven middle layer is meltblown layer bottom layer is spunbond nonwoven The food pad is made up of 3 layers of non-woven material: - An outer layer of spunbond/film - A meltblown filtration layer/sap , saf , fluff, pulp absorbent layer - An inner layer of spunbond/film surgical mask line food pad meat pad fruit pad These product features are realized thanks to the use of precise welding rollers, a modern and intuitive HMI with touchscreen function for simple and clear operation, as well as web guiding systems implemented. Intelligent sensors ensure that the material levels are precisely determined. If a low material level is detected, the material is welded to one another using the autosplice function without stopping the system. Plant details: - Solid, high-quality system structure with over 25 tonnes for maximum stability - Pneumatic material winding shafts for flexible and easy exchange of the rolls - Pneumatic material winding shafts in double design for quick set-up times and convenient handling Nedpfx Aeh Rwk Tea Esdf - Adjustable web tension through pneumatic modules - Autosplice function for convenient material welding at the end of the roll - Individually controlled winding shafts for maximum precision E3b2qnt - Servo driven unwinder, PLC control - Sensor technology for material presence control - Automated alarm & stop function in the event of material tear - Web guiding for maximum precision of the raw material - Large and intuitive touchscreen - The touch screen can display the diameter of the rolls, the material ratio, the servo load and alarm codes - The machine speed can be conveniently set on the touchscreen - Error messages can be tracked in the alarm and error history. These include: Raw material, joining, splicing and fan defects - The production quantities and other details can be viewed on the HMI aswell Performance data: - Power consumption: on request - Power connection: 380 V / 50 Hz - Number of cycles: up to 800 masks / min. - depending on the material - Carton: depending on the packaging format - Compressed air: 6-8 bar with sufficient volume / reserve - Dimensions: 15 m x 4 m x 3 m (LxWxH) - different depending on the equipment - Weight: 25 tonnes - varies depending on the equipment System modules: - Unwinding units for spunbond, meltblown andfilm with automatic splicing unit side embossing unit - Triple folding food pad. - food pad n the side embossing unit - End cutting unit (high speed steel) - Product exit conveyor - Single pack packaging module - Security doors with sliding construction

Condition: used, Year of construction: 1986, plate thickness 6,0 mm pressure 18 t cutting angle - upper blade 90 ° blade length 225 x 225 mm voltage 380 V total power requirement 5,5 kW weight of the machine ca. 650 kg Ndjdpfx Aaeg Ip Efj Eef dimensions of the machine ca. 1,10 x 0,80 x 1,05 m - Angular stops adjustable

Condition: new, sheet width 2050 mm plate thickness 3 mm distance between columns 2100 mm back stop - adjustable 600 mm connected load kW weight of the machine ca. 1,1 t dimensions 2,7 x 2,1 x 1,4 m The machine works quietly and it is energy-saving by its gear motor and brake system. Our machine is manufactured as steel construction monoblock body welded from ST42 quality material. The blades on the machine are of 2379 quality and the brand’s name is BOHLER. These high-quality blades ensure quality and precise cutting. Emergency stop button and finger guard grill are standard equipment of foot Ndedpsfv H Dkefx Aa Esf pedal machine.

Year of construction: 1989, condition: excellent (used), Sägeblattdurchmesser: 350 Ndsdpfxeff Snbj Aa Eef

Condition: new, Year of construction: 2025, Fully automatic cutting of medium-large aluminium profiles with simple-to-use automation. Put down any aluminium profile, the machine will automatically detect it and cut it into jobs tasked with high-accuracy servo motor material positioning. Excel job lists WIFI input for streamlined input of large cutting lists. For every piece of aluminium you place down to cut, no matter what length, a laser sensor measures its length. Our powerful optimisation algorithm on-the-fly calculates the best order of parts to produce minimum waste. The machine automatically cuts the calculated list without stopping. No need for any inputs from you, just keep putting in new aluminium stock. Simple, high-speed alternative to double-headed saws. Just enter (or import) the lengths and angles you need and press GO. The machine continuously produces your angled parts, accurately and at high speed. • Fully-automatic cutting operation with bar feeding and cutting to length. • Simple user interface for automatic operation, enter job and cut in seconds. • Simplified part, batch, or large excel lists job cutting. • Bundled / multi-bar cutting and counting. • Remote WIFI excel job lists input with extensive data mapping capabilities. • Fully adjustable saw cutting and timber feeding rates for maximum process productivity. • Automatic optimiser mode with timber laser length measure and optimisation for minimum waste (optional). • Automatic labels printing for parts using data from the job list (manual label application, optional). • Inline direct-to-material printing with no operator action required (optional). • Bar codes or QR codes printing or scanning for jobs input (optional). • Automated servo positioning of the saw mitre angle up to ±75° (optional). Highly suitable for: • Windows and doors manufacture • Mitered aluminium structures manufacture Njdpfx Aajf Eknno Esdf • Aluminium fabricated structures manufacture • Composites manufacture • Blinds, shades and furniture manufacture • Aluminium retail sales Model: A550 Length: 9 m Linear Unit: ProfiStop Alpha Material Length: 8580 mm Pushing capacity: 20 - 40 kg Software: Optimiser QUALITY AUSTRALIAN-MADE MACHINES.

Condition: new, Cutting range: round 0°: 170 mm square 0°: 150 x 150 mm flat 0°: 150 x 190 mm round 45°: 125 mm square 45°: 95 x 120 mm working height : 870 mm cutting speeds : 40 / 80 m/min saw band: 2080 x 20 x 0,9 mm coolant pump: 100 W saw motor: 0,75 kW connection: 400 V dimensions L x W x H, approx.: 1340 x 810 x 1320 mm Weight, approx.: 146 kg Features: - Saw bow can be tilted up to 45°. - With 2 saw blade speeds for optimum adaptation to the workpiece - Ideal for cutting tubes, profile material as well as solid material made of VA, iron, etc. - Generously dimensioned saw arm for low-vibration work - Lowering of the saw arm via hydraulic lowering cylinder - Low noise level due to stable design - Switch-off after end of cut by micro limit switch - Quick-action vice for simple and fast workpiece clamping - Precise, adjustable saw blade guide for optimum cutting results - Coolant system with pump - Incl. base frame - CE/IEC, German documentation and German service Scope of delivery: - BiMetal saw band 2080 x 20 x 0.9 mm, 6/10 ZpZ - Band tension adjustable via manometer - quick clamping vice - material stop - Coolant device with pump - Hydraulic lowering cylinder - Motor protection switch - Automatic limit stop after end of cut - underframe Ndsdpeilk H Tsfx Aa Esf