Extrusion Plant

Artec 145DV

Year of construction: 2003, condition: reconditioned (used), Stock - No. 2651 1 used underwater pelletizing unit, Bjdpfx Afeiyyf Ienjwh partially overhauled in 2023 Throughput up to approx. 450 kg/h depending on the material, consisting of: Type BKG ( Nordson ) Start-up valve with hydraulic station Granulator type A300 including die-plate and cutter bar, drive 4.4 kW by-pass system TVE 1000 ED pellet-dryer drive 4 kW incl. Agglomerate catcher Tempered water system with Water box 200 liters, installed heating capacity 9 kW Water pump 2.2 kW with 15³/h heat exchanger Control unit - NEW Further UWP pelletizing units are available ex workshop in Wuppertal-Germany ( as Gala, BKG Nordson, Econ ) Available from the Wuppertal warehouse: complete compounding, pelletizing extrusion lines, with single-screw or twin-screw extruder.

Condition: new, machine/vehicle number: Baureihe GSL 300 / Neumaschine, The cutting mills in the GSL series 300/400 to 300/800 are primarily intended for the shredding of production-related scrap material in the injection molding and blow molding sectors. In addition to the key advantages of the GSL series, the slow-running cutting mills GSL 300/400, GSL 300/600 and GSL 300/800 are particularly suitable for large-area parts, such as car door panels, bumpers or hollow bodies. Bsdpfx Afjghgbhenowh The "V-arrangement" of the rotor blades keeps the pre-shredded material in the center of the rotor. This significantly reduces wear on the grinding chamber walls when grinding glass fiber reinforced plastics. Material sticking to the side walls is avoided. The staggered arrangement of the rotor disks means that only individual blades are used at any one time, so a higher cutting force is available in each case.

Condition: good (used), Year of construction: 2014, Pellet Press Manufacturer - TEKNO UNO Bedovdrtxspfx Afnjwh Model - TK 304 Year - 2014 Motor Power - 50 kw Capacity - 450 kg/h

Year of construction: 2016, condition: excellent (used), functionality: fully functional, Make: Reifenhauser Model: Mirex-MT-V 1-RZE 120-1800 Year: 2016 Condition: Excellent Use: PET / PP / PS Foil or Sheet PET: Thickness Range: 0.25 - 2.2mm Output: 2,000 kg/h Max Sheet Width: 1600mm Extruder: RZE 120mm Electrical Supply: 3 x 480V 60Hz with N Calendar Roll Width: 1800mm Calendar Roll Diameters: 450 / 700 / 700mm Silicon Bath Max Sheet Width: 1600mm Silicon Bath Sheet Thickness Range: 0.15 - 1.5mm 4 Position Winder WOB 1800 for double web winding included. All details are subject to change and/or errors. All equipment is subject to availability and/or prior sale. Bwedpfx Aovbcbuofneh

Condition: new, functionality: fully functional, - Single screw extruder - 25/25 LD screw - Motor: 2.2 kW - Wide slot die adapted 1.0 x 120 mm - With cooling rollers (200 mm wide) - Winder / haul-off Bederg Ebcjpfx Afnowh - Control system

Condition: new, Year of construction: 2023, machine/vehicle number: 7YXXX, VIS G is the ideal and the most efficent solution for serap processing like stampings, trimmings, wires mostly recommended for the automotive industry, metal recyclers and non-ferrous metal remelting industry. Bsdpfxsmqi Ake Afnjwh

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, input current: 238 A, overall weight: 36,000 kg, oil tank capacity: 1,300 l, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Bodpsvf E Avefx Afnswh Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Year of construction: 2010, condition: ready for operation (used), Volume flow: 1000m³/h, max. depression: 10,000Pa, motor power: 5.5kW, weight: 350kg. Bwsdpfx Afehz Dx Sonsh

Condition: used, machine/vehicle number: 11431, Rotor diameter: 450 mm Rotor width: 600 mm Paddle rotor Bodjghgl Sjpfx Afnowh 3x3 rotor blades (offset), 2 rows of stator blades Inlet cross-section approx. 550 x 625 mm Drive motor 30 kW Suitability: Primarily for shredding hollow blow moldings and bulky molded items such as bottles, canisters, jugs, bowls, baskets, buckets, tubs, etc.

Year of construction: 2007, condition: excellent (used), EXTRUDEX EXTRUDER EN50-30D year 2007 no. 4101264, with melt pump, screen changer and 5 layer pipe head Year of manufacture 2007 As well as 4 co-extruders EXTRUDEX EN25-25D, year of manufacture 2007 APPLICATION: Production of PE 5 layer pipes Max diameter 32 mm INVENTORY: 1 single-screw main extruder EN 50 Bsdpfxsvyaxuo Afnswh 4 co-extruders single-screw auxiliary extruders The extrusion system is my property Location: D-26345 Bockhorn-Grabstede, Bahnhofstr 6, Germany