Kazemiyeh-Maschinenhandel

Condition: good (used), Year of construction: 2016, Subject to differential taxation according to §25a of the German VAT Act. You will receive a proper invoice; however, VAT will not be shown. Internal item no.: 26016 You are welcome to inspect the machine under power on more than 500 m² of heated warehouse space. Lead and feed screw lathe Wagner DLC 200B x 1000 Year: 2016 + Digital readout + Multifix "B" + 3-jaw chuck D250 + Steady rest (not shown in pictures) Bodpfxjyg Hcwj Afnswh + Coolant pump + Chuck guard Centre distance: 1000 mm Centre height: 210 mm LxWxH (approx.): 230 x 110 x 170 cm Weight: 1800 kg The machine comes from an educational facility and is in well-maintained condition.

Condition: ready for operation (used), Year of construction: 1966, Immediately available from location: L & Z Lathe Weiler Year of manufacture approx. 1966 Centre height 140 mm Swing diameter 280 mm Bwsdpfx Aoyg Emnjfnjh Over carriage 180 mm Turning length 800 mm Spindle bore 24 mm Spindle speeds up to 1600 rpm Drive power 2 kW Chuck diameter 140 mm Multifix tool holder with inserts Weight 1 ton Priced at EUR 1,500.— plus VAT ex location

Condition: good (used), Subject to differential taxation according to §25a of the VAT Act. You will receive a proper invoice, however, VAT will not be shown separately. Internal item no.: 26010 You are welcome to inspect the machine under power in our heated warehouse of over 500 m². Leadscrew and feedshaft lathe Voest Alpine DA180 Bwodoyg Dtgspfx Afnjh + Coolant system + Röhm 200 four-jaw chuck + Chuck guard (with switch) + Multifix "B" Motor: 380 Volt / 5.5 kW Speed: 44 - 2,000 rpm Swing over bed: 380 mm Swing over cross slide: 185 mm Turning length: 1,000 mm Centre height: 180 mm Bed width: 330 mm Spindle bore: 52 mm Tailstock taper: MK 4 Dimensions (LxWxH): 220 x 120 x 160 cm Weight: approx. 1,200 kg The machine comes from an educational institution and is in well-maintained condition.

Condition: good (used), Year of construction: 1983, Margin scheme taxed according to §25a German VAT Act. You will receive a proper invoice; however, VAT will not be shown separately. Internal article no.: 26012 You are welcome to inspect the machine under power on over 500m² of heated storage area. Leadscrew and feed shaft lathe Voest Alpine DA180 Max. swing over bed: 380mm Distance between centers: 800mm Spindle bore: 52mm Tailstock: MT4 Multifix "B" basic holder Chuck guard (with switch) Röhm 3-jaw chuck 200mm Dimensions (LxWxH): 250 x 140 x 140cm Weight: approx. 1200kg Bwedpjyg Dl Ajfx Afneh The machine comes from a training facility and is in well-maintained condition.

Condition: used, Year of construction: 1996, turning length 1.000 mm turning diameter over bed 400 mm turning diameter over slide 240 mm Bodpfx Aeygm Ugefnewh spindle bore 52 mm spindle tunring speed 30 - 1.600 U/min In our assessment, the machine is in good used condition and can be inspected under power by appointment. Accessories, tools, and clamping devices shown are only included in the scope of delivery if this is noted in the additional information. Technical data and specifications are subject to change without notice and errors. Prior sale is reserved.

Condition: good (used), L&Z spindle lathe WEILER COMMODOR B from educational institution -GS identification -3-axis digital readout "NEW" -Centre height: 180 mm -Centre distance: 1000 mm -Spindle bore: 56 mm -Spindle speeds: 15 - 2000 rpm -Automatic longitudinal & cross feeds -Thread cutting: metric / imperial / module / diametral pitch -Electric chuck guard -2 x emergency stop Bwjdpfx Afeyf U E Deneh -Multifix with insert -Four-jaw chuck - Röhm -Chip guard rear panel -Coolant system -Very well-maintained original condition -Documentation Dimensions: LxWxH 2.3x1.2x1.7 m / Weight 1600 kg Errors and omissions excepted

Condition: excellent (used), Year of construction: 2014, functionality: fully functional, Weiler Praktikant VC Plus Precision Lead and Feed Screw Lathe with 3-Axis Digital Readout, Infinitely Variable Speed, Excellent Condition Technical Data: Bodpfjydczdox Afnowh >> Year of manufacture: 2014, Machine no. JD12 >> Centre height: 160 mm >> Swing over bed: 320 mm >> Swing over cross slide: 190 mm >> Distance between centres: 650 mm >> Spindle speeds: 30 – 4000 rpm (infinitely variable) >> Spindle bore: 43 mm >> Short taper spindle nose DIN 55027 size 5 with bayonet lock >> Tailstock: MT 3 >> Infinitely variable feed adjustment during operation via potentiometer (override) >> Input of feed rates and thread pitches >> Longitudinal feeds from 0.1 to 6 mm/rev >> Cross feeds from 0.003 to 2 mm/rev >> Thread cutting possible: metric, imperial, module, and diametral pitch >> Metric thread pitches from 0.1 to 20 mm >> Weight approx. 1,400 kg >> Spindle brake >> Dimensions: approx. 1.72 m (L), 1.7 m (H), 0.89 m (D) Accessories and Features: >> Weiler digital readout >> Collet chuck (new), collet set NEW from 3 to 26 mm >> 160 mm 3-jaw chuck with 1 set of jaws >> 160 mm 4-jaw chuck with 2 sets of jaws >> Multifix size B quick change toolpost with 3 tool holders >> 1 bed stop >> Splash guard >> Coolant system >> Machine lamp >> Operating manual, spare parts diagram Safety Features: >> Lockable main switch >> Emergency stop button >> Electrically monitored chuck guard >> Automatic disengagement of the respective handwheel when feed is engaged VCplus Digital Readout: >> 8 inch color display >> 3 axes for bed, cross, and compound slides >> 99-tool memory >> Spindle orientation stop >> Input of either constant speed or cutting speed >> Feed and threading settings are displayed >> Thread cutting with electronic stop About the machine: Offered here is a Weiler Praktikant VC Plus precision lead and feed screw lathe with 3-axis digital readout. Year of manufacture 2014, in very good condition with original paint. The machine is, of course, fully functional and equipped with new collets and chucks. Take the opportunity to inspect the machine under power at our premises and see its condition for yourself.

Condition: used, Year of construction: 1975, turning diameter over bed 380 mm turning diameter over slide rest 215 mm turning length 1250 mm spindle bore 41 mm bed width 340 mm number of spindle speeds 12 spindle turning speed range 14-2800 U/min Bwjdpfx Afjycxf Aonoh total power requirement 6 kW weight of the machine ca. 1,85 t dimensions of the machine ca. 3 x 1 x 1,35 m Special price sale directly from the factory! Machine dealer with own stock of 1600 m².

Condition: used, Year of construction: 1991, functionality: fully functional, machine/vehicle number: 91-160-2498, Used WEILER PRAKTIKANT 160 lead and feed screw lathe Centre height: 160 mm Centre distance: 650 mm Spindle speeds approx. 48–2,500 rpm Spindle bore: 40.5 mm Bwsdpfx Afsyciw Asnsh Leadscrew and feed shaft are covered. Scope of delivery: Including 3-axis digital readout from Heidenhain, chip guard back wall, lever collet system (without collets), 1 x faceplate Ø 250 mm, electrically interlocked chuck guard, machine lamp, Multifix size A quick-change toolpost with 4 holders, bed stop, cooling unit, and fixed steady rest. The machine is located at our premises in 71334 Waiblingen-Beinstein and is available immediately. Viewing by appointment is possible.

Condition: excellent (used), Year of construction: 1990, functionality: fully functional, machine/vehicle number: LVM50GIRJA/02115, MACHINE SPECIFICATION Height of centres 170mm Swing over bed 350mm Swing over cross slide 196mm Swing in gap 535mm Width front of faceplate 165mm Bed length between centres 1250mm Spindle speeds (infinitely variable) 15-3250rpm Spindle nose mounting (Camlock) D1-4 Spindle Bore 42mm Spindle motor 7.5Kw Width over bedways 318mm Travel cross slide 250mm Travel top slide 100mm Travel tailstock barrel 145mm Taper in tailstock barrel No. 4MT Machine in Imperial execution Bodpfx Asycg Thofnewh MACHINE EQUIPPED WITH Newall DP700 2 axis DRO system 3 jaw chuck Quick change toolpost and 3 toolholders Bedstop Lighting Chuck guard Coolant system Rear splashguard

Condition: good (used), Please read the technical specifications carefully. If the machine is suitable for your investment, we kindly request a complete verification of your identity, including a correct telephone number and email address, prior to submitting an offer. Lead and feed screw lathe Colchester Triumph 2000 Turning length: 750 mm Swing over bed: 390 mm Swing over cross slide: 240 mm Largest swing in the gap: 580 mm Gap length in front of faceplate: 155 mm Spindle bore: Ø 54 mm Spindle mount: 6" D1 Camlock Tailstock: MT4 Quill stroke: 155 mm 16 spindle speeds from 25 to 2000 rpm 39 metric thread pitches from 0.2–14 mm 45 Whitworth thread pitches from 2–72 tpi 18 module thread pitches from 0.3–3.5 module 21 diametral pitch threads from 8–44 DP 15 longitudinal feeds from 0.04–1.0 mm/rev 15 cross feeds from 0.02–0.5 mm/rev Dimensions (LxWxH): 2000 x 980 x 1640 mm Weight: 1350 kg The machine and bed are in good condition and run perfectly. Cross slide backlash: 0.2 mm Top slide backlash: 0.4 mm Accessories/Equipment: - Chuck guard - Machine lamp - Multifix B toolpost - Bed stop Bwsdpfsyb A Uxox Afneh - 3-jaw chuck D250 mm - Machine feet

Condition: good (used), Year of construction: 1999, From a training workshop: GDW LZ 350 Year of manufacture: 1999 Distance between centers: 825 mm Spindle bore: 38 mm Swing diameter: 360 mm 3-axis digital readout from Axesta Speed range: 45–2000 rpm Röhm ZS 160 three-jaw chuck Work light Coolant pump Bwjdeyag Iyspfx Afneh 2x emergency stop Accessories: Multifix Machine feet Change gears 2x Multifix Spare jaws for chuck Operating manual + machine card 380 Volt Weight: 950 kg Dimensions (approx. in mm): 1800x900x1650

Condition: good (used), Year of construction: 2007, functionality: fully functional, turning diameter over cross slide: 330 mm, spindle bore: 52 mm, turning diameter: 330 mm, turning diameter over bed slide: 160 mm, turning diameter over top slide: 160 mm, center width: 1,000 mm, turning length: 1,000 mm, total length: 1,800 mm, total width: 650 mm, total height: 1,400 mm, spindle speed (max.): 2,000 rpm, spindle speed (min.): 70 rpm, Distance between centres: 1.000 mm Swing: 330 mm over bed / 160 mm over cross slide Bwedpfxeyac Ens Afnjh Spindle bore: 52 mm Spindle speed: 70 - 2.000 rpm Featured with: - 1x fixed steady, 1x moving steady - Gearwheels-set - Flat chuck - Chuck protection hatch - Cooling unit Country of origin: The Netherlands Machine LxWxH: 1.800 x 650 x 1.400 mm Machine weight: 750 kg

Condition: used, Year of construction: 1960, centre distance 1200 mm Bedpfxex U A Igj Afnewh 550 weight of the machine ca. 2,5 t

Condition: good (used), Year of construction: 1985, functionality: fully functional, turning diameter over cross slide: 160 mm, spindle bore: 36 mm, turning diameter: 300 mm, center height: 150 mm, center width: 500 mm, total length: 1,500 mm, total width: 800 mm, total height: 1,300 mm, spindle speed (max.): 3,550 rpm, spindle speed (min.): 15 rpm, overall weight: 1,000 kg, Conventional lathe, center high 150 mm, between centers 500 mm, bore Ø 36 mm, 18 speed 15 - 3550 rpm, motor 3 kw, equipement: collet device, coolant device, 3-jaws chuck, rotating pin, drill chuck, tool post RAPID with 5 toolholders, lamp, dimensions 150x80x130 cm, weight ca. 1000 kgs Bwsdpfx Afox Urmljneh

Condition: new, Year of construction: 2025, functionality: fully functional, center height: 155 mm, total length: 1,632 mm, total width: 770 mm, total height: 540 mm, spindle speed (max.): 2,500 rpm, spindle speed (min.): 50 rpm, bed width: 190 mm, overall weight: 360 kg, three-jaw chuck diameter: 160 mm, Substructure is not included, but can be added. Bwsdpfsx Tr Rzox Afnoh Delivery Contents: Three-jaw lathe chuck Ø 160 mm, No. 4 Reducing sleeve MK 5 / MK 3 Two non-moving center points MK 3 Quadruple steel holder 25 mm Set of change gears Machine initial filling with quality oil Operating tool

Condition: good (used), Year of construction: 2000, machine/vehicle number: 1101188, GDW LZ 250 lead and feed screw lathe Bodpfox Slhdjx Afnswh Year of manufacture: 2000 Centre height: 125 mm Centre distance: 500 mm Spindle bore: 38 mm Spindle mount: DIN 55027/4 Tailstock taper: MK 3 Speed range: 60 - 3,000 rpm, stepless Weight: approx. 600 kg Dimensions: approx. 1,300 x 700 x 1,400 mm With collet chuck mechanism With Iskra digital readout

Condition: like new (used), – Centre distance 1000 mm – Swing over bed 360 mm – Swing over gap 490 mm – Swing over cross slide 180 mm – Spindle bore 52 mm – 70–2000 rpm – Infinitely variable speed – Digital speed display – Longitudinal and cross feed – Digital readout on two axes – Brake – Coolant system – Lighting – Safety cover – Fixed steady rest Bwjdpfxjx N A D Ds Afnsh – Travelling steady rest – Three-jaw chuck – Four-jaw chuck – Emergency stop – Documentation – 400V

Condition: excellent (used), For sale: the Austrian-made Voest DA160 lathe shown in the photos. The machine is in very good condition, as indicated by the quiet spindle operation and the absence of play in the mechanisms. The machine was purchased from a training workshop. Overall condition is rated as very good. Loading of the machine is provided. Price is net. Spindle speed: 30–2500 rpm Two-speed motor Motor power: 2/2.4 kW 16 spindle speeds Rohm 160 chuck Internal, external, and split jaws Spindle bore: 36 mm Tailstock quill: MK3 Quill travel: 100 mm Turning diameter: 320 mm Turning diameter over carriage: 190 mm Bjdpox Nxuljfx Afnowh Turning length: 650 mm Dimensions: 85x150x140 + 15 (pallet) Weight: 700 kg

Condition: excellent (used), Year of construction: 1992, functionality: fully functional, Weiler Praktikant 160 B Lead and Feed Screw Lathe with K&C 3-Axis Digital Readout, from Vocational School Technical Data: >> Year of manufacture: 1992; Machine No.: 92 160 3271 >> Center height: 160 mm Bsdpfxjx H S D Is Afnowh >> Distance between centers: 650 mm >> Spindle speeds: from 24 to 2500 rpm >> Spindle bore: 40 mm >> Short taper spindle nose DIN 55027, size 5 with bayonet lock >> Tailstock: Morse taper 3 >> Feeds: from 0.02 to 0.63 mm/rev >> Thread cutting capability: metric, inch, module, and diametral pitch threads >> Metric thread pitches: from 0.25 to 8 mm >> Weight: approx. 680 kg >> Switchable spindle brake >> Dimensions: 1.6 m (L), 1.25 m (H), 0.7 m (D) Accessories and Features: >> 3-axis digital readout by K&C incl. operating manual Functions: mm/inch switching, coordinate selection ABS/INC, display value halving, reference mark, tool programming for up to 200 tools, taper calculation, radius/diameter, quick zeroing, count direction switching >> Collet system with NEW collets from 3 to 26 mm in 1 mm increments >> 160 mm 3-jaw chuck (clamping jaws) with 1 set of jaws >> Quick-change system with 4 toolholders >> Bed stop >> Electronic spindle guard >> Rear cover >> Coolant system >> Operating manual, spare parts diagram About the Machine: Offered is a Weiler Praktikant 160 B lead and feed screw lathe, toolroom accuracy, year 1992, in very good condition. The machine is, of course, fully functional. All slides move smoothly and evenly. Even at high spindle speeds, the Weiler runs quietly. This newer generation of Weiler lathes is very user-friendly and enables the production of ground-like surface finishes. Take the opportunity to inspect this machine under power on-site and see for yourself its excellent condition.

Condition: used, Year of construction: 2003, machine/vehicle number: 1527, Used lead and feed screw lathe COLCHESTER Triumph VS 2500 Centre height: 195mm Bsdpfx Afjx Hrumsnswh Distance between centers: 650mm Spindle bore: 54mm Infinitely variable speed: 14–2500 rpm Tailstock quill: MT5, coolant system, quick thread cutting device Digital readout: FAGOR NUP 300 TS-RS 1 x RÖHM 3-jaw chuck, 5-position stop drum, spindle stop, machine lamp, 1 x PARAT 4-way turret, 4 x PARAT tool holders, live centre and quick-action drill chuck. The machine is located at our premises in 71334 Waiblingen-Beinstein and is available immediately. Inspection of the machine is possible by appointment.

Condition: excellent (used), functionality: fully functional, Schaublin 135 High Precision Lathe with 3-Axis Digital Readout (ELESTA) and Accessory Cabinet in Excellent University Condition! Technical Data: - Centre Height: 135 mm Bwjdpfxsx Hivns Afnoh - Distance Between Centres: 630 mm - Swing Over Bed: 315 mm - Spindle Nose: Camlock D1-4 - Spindle Bore: 40 mm - Longitudinal and Cross Feeds: 0.025–0.35 mm/rev - Metric Threads: 0.25–14 mm - Tailstock Taper: MK3 - Infinitely Variable Speeds: 55–3000 rpm - Total Power Requirement: 4.45 kW - Weight: approx. 1,200 kg Accessories: - 3-Axis Digital Readout (ELESTA) with Heidenhain Scales - Accessory Cabinet including: - 160 mm 3-jaw chuck with 2 sets of jaws - Multifix B, 3 tool holders - Internal and external quick-change collet system - Change gears - Eccentric chuck - Faceplates - Fixed and travelling steadies - Coolant system - Centre points - Operating manual - And much more About the Machine: For sale is a Schaublin 135 high precision lathe. The machine is in very good condition, comes from a university, and has seen very little use. It is equipped with a 3-axis digital readout and a wide range of accessories. Take the opportunity to inspect the machine under power on site and see the condition for yourself.

Condition: used, Year of construction: 2000, used CONDOR AC, partially overhauled Centre height: 165 mm Between centres: 750 mm Spindle bore: 40 mm Bedpfxex E Um Ne Afnewh Spindle speeds: 22–2,800 rpm, infinitely variable - Quick-change tool post size B - WEILER DZ-V digital readout - Hollow spindle stop - Fixed steady rest - 7 Multifix tool holders - Flat splash guard - Electrically interlocked chuck guard - Change gears and various soft jaws The machine is partially overhauled: - Bed slide: guideways re-coated and hand-scraped, gibs and lower guide strips adjusted - Cross slide measured and aligned on bed slide; cross slide dovetail guide newly scraped, gibs adjusted and scraped - Top slide newly scraped and gib matched - All measuring scales overhauled and cables replaced The machine is located in our showroom at 71334 Waiblingen-Beinstein and is immediately available. For details on equipment, please contact us.

Condition: used, Year of construction: 2014, turning diameter: 340 mm, turning length: 2,000 mm, total length: 4,270 mm, total width: 2,130 mm, total height: 1,840 mm, overall weight: 3,900 kg, 2-Axis Teach-In / Cycle controlled CNC Lathe CNC Control Fagor 8055 I Power TC Bwjdpex E Tahjfx Afneh Turning diameter 340/570 mm Turning length 2000 mm Center height 275 mm Spindle bore diameter 108 mm Spindle nose D 1-8 Spindle speed 0-2.500 R/min Movement X-axis 310 mm Movement Z-axis 2000 mm If you have any questions concerning the machine, please do not hesitate to contact us by phone or e-mail. Feel free to view our other advertisements for a complete overview of our stock.

Condition: used, total length: 1,500 mm, total width: 750 mm, total height: 1,350 mm, Empty weight: 700 kg - Documentation available: Yes - CE certificate present: No - Drive system: Conventional - Centre height [mm]: 150 - Swing over bed [mm]: 300 - Carriage turning diameter [mm]: 160 - Distance between centres [mm]: 500 - Bed width [mm]: 210 - Spindle bore [mm]: 36 - Min. spindle speed [rpm]: 15 Bedpfjx D Tlrox Afnjwh - Max. spindle speed [rpm]: 3550 - Transport dimensions: 1500mm x 750mm x 1350mm (l x w x h) - Transport weight [kg]: 700kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum