Brushing machine, grinding machine, deburring machine

- Italy MASTER ROTOR 400 DOUBLE

Condition: excellent (used), Number of sanding units 4 St. sanding width 190 mm Sanding height max. 180 mm Control ja weight 3300 kg Dimensions (L/W/H) 2600x920x1890 mm Dust suction hood 2x180, 2x120 mm Löwer DSM 2004 Double-Sided Sanding Machine ----- 4-Belt Sander + Disc Unit (Top/Bottom) Manufacturer's Description: ----- Double-sided, four-belt, single-wood sander for sanding solid wood such as window frames, etc. Highly stable, top-quality design with innovative details. Suitable for high continuous loads, even with high material removal rates. - Sequentially arranged grinding units for roughing, fine grinding, and finishing, each from above and below 1. Belt grinding unit with heavy steel roller 2. Belt grinding unit with rubberized roller and shoe 3. Finishing unit with fiber brush (see optional equipment below) - Direct-drive grinding rollers for slip-free power transmission - Maintenance-free and wear-free CERMET-coated grinding shoes with very good thermal conductivity and absolute dimensional accuracy Guodpovu Hgbefx Ahned - External cooling of the grinding zones for cooler grinding and longer belt life - Forced pneumatically controlled grinding belt oscillation - Effective grinding dust extraction directly at the grinding rollers - Airborne dust extraction at the tension rollers - Integrated brushing and finishing unit with large grinding dust extraction - Motorized grinding thickness adjustment via precision threaded spindles and large linear ball bearing sets on hardened and ground precision shafts with dust and Dirt protection - Chip removal adjustment at the bottom via precision threaded spindle with dimension display via scale ring (0.1 mm resolution) - Sanding belt tension via pneumatic cylinder with constant tension pressure - Sanding belt change with pneumatic belt release in seconds - Sanding belt tracking adjustment during belt change - Electropneumatic compressed air monitoring - Infeed protection via contact roller for workpieces that are too thick - Workpiece transport via calibrated, non-slip and adhesive conveyor belts over heavy-duty cast iron tables with a finely planed surface and spring-loaded pressure rollers with fine adjustment - Cardan shaft drive for smooth and consistent workpiece transport - Geared feed motor with infinitely variable speed 4-20 m/min - All motors electrically protected - Ergonomically arranged operating elements - Digital thickness display (0.1 mm resolution) with modern magnetic tape system Technical data: ----- - Sanding belt speed 22 m/s - Sanding belt length 1800 mm - Sanding belt width 200 mm - Working width 190 mm - Sanding thickness 2-180 mm - Four brake motors for drive 5.5 kW - Feed motor 1.5 kW - Feed speed 4-20 m/min - Automatic height adjustment 0.37 kW - Two brush units with fiber brushes D 120 x 200 mm at 0.37 kW each - Extraction ports 2 x 180 mm, 2 x 120 mm - Extraction air velocity 20 m/s - Pneumatic connection 6 bar - Working height 870 mm - Length (with soft disc 2740 mm) 2600 mm - Length with control unit (with soft disc 3035 mm) 2985 mm - Width 880 mm - Height 1910 mm - Weight approx. 3300 kg - Operating voltage 400 volts, 50 Hz, 3P - CE compliant Equipped with the following special options: -----...

Condition: new, Year of construction: 2024, Working width: 600 mm Working height: 150 mm Gujdoug Ty Hepfx Ahnod Units: 4 brush units separately adjustable 1st unit, rotor group: group of 5 oscillating rotor brushes, Ø 115, each with a 3 kW motor 2nd unit, rotor group: group of 5 oscillating rotor brushes, Ø 115, each with one 3 kW motor 3rd unit, brush: Scotch Brite Hard / diameter 220mm, Vario drive 4th unit, brush: Scotch Brite Hard / diameter 220mm, Vario drive Height adjustment: electric Height display: digital Control: touchscreen Feed speed: 4 - 12 m/min Motor power feed: 0.37 kW Machine length: Machine width: Weight:

Condition: used, functionality: fully functional, input voltage: 400 V, type of input current: three-phase, cutting height (max.): 400 mm, saw band length: 5,550 mm, saw band width: 80 mm, table length: 800 mm, table width: 1,060 mm, working height: 400 mm, - Italian manufacture - Lamella band saw - Unpainted - Very good condition - Used saw Band Saw: - Wheel diameter: 800 mm - Max. blade width: 80 mm - Max. cutting height: 400 mm - Main drive motor: 11 kW - Feed speed range: 2–40 m/min - Feed system with pneumatic pressure to the guide - Metal slip-in feed roller - Blade length: 5550 mm - Throat (blade-to-frame distance): 780 mm - Screw-type blade tensioning - Table size: 1060x800 mm - Tilting worktable: up to 15° - Extraction port diameter: 120 mm Gjdow H Rq Hspfx Ahnsud - Blade lubrication system - Foot brake - Cast wheels - Star/Delta starting - Power supply: 380V - Dimensions (LxWxH): 1600x1100x2400 mm - Weight: 860 kg Feed Unit: - Metal, toothed, drive roller - Five feed speeds, selectable by belt adjustment - Roller height: 30 mm - Feed motor: 0.75 kW - Pressure system

Condition: excellent (used), functionality: fully functional, Year of construction: 2017, Wire diameter range: 2,0 - 10,0 mm Wire feeding length: unlimited No. of CNC-axes: 5 Bend-back clearance: max. 600 mm Weight: 2.400 Kg. *with chamfering unit* Gusdpfxjy Ehrfj Ahnjd complete with an motorized wire decoiler table diamtere: 1.500 mm loading capacity: 1.500 Kg.

Condition: used, No. 3213 Thermal treatment system / vacuum dryer WTT Used, year of construction 2017 Thermal treatment system / thermal chamber for the modification of wood The WTT thermal chamber is a system for the thermal modification of wood. It enables efficient treatment of 2 to 3 batches per day, depending on the thickness and type of wood. The system has a powerful energy and heat transfer system and works with a gas or oil-fired boiler system that uses thermal oil as a heat transfer medium. Technical data: Capacity: 5950 - 9900 m³ of wood per year (for 330 working days) Usable volume: 9 m³ (with 50 mm wood thickness) Stack dimensions: 10500 x 1300 x 1100 mm LWH Minimum board thickness: 10 mm Power connection: 3 x 400 V, 50 Hz + zero + earth, 63 A Specific power consumption: 15.9 kW/m³ Maximum heat output: 2 MW (230 °C - 250 °C thermal oil) Heat consumption: 120 kWh/m³ wood Autoclave length: 11,000 mm Autoclave diameter: 1,800 mm Autoclave material: 10 mm stainless steel duplex EN 4462 Door opens hydraulically, with 1.5 kW drive Working pressure: 0.1 to 15 bar (absolute) Working temperature: 0 °C to 220 °C 200 mm glass wool insulation, clad with 1 mm galvanized sheet steel Main components: 1. autoclave, in which the heat treatment takes place 2. vacuum system that sucks the air out of the autoclave before heat is applied 3. energy center with a 2 MW oil burner 4. 4 MW cooling system with dry coolers 5. nitrogen generator 6. gas cooler system Heating and cooling system: Heat exchanger: 8 units (4 on each side) Material: Stainless steel pipes (seawater resistant) Total floor area: 165 m² Cooling water consumption: 1000 l/batch (not contaminated, only heated) Control and operation: Control system: WTT ExoT (fully automatic) 22” color monitor, IBM computer, printer Sensors: 4 PT100 temperature sensors 2 mechanical thermometers 1 vacuum/pressure transmitter 1 mechanical vacuum/pressure gauge Special equipment: Hydraulic rail bridge for convenient transportation of wooden trolleys Automatic trolley extraction with cable winch (1.5 kW) 2 MW thermal oil boiler (heating) Fuel oil tank (4000 l) with measuring system Insulated 20 foot steel container for heating module Stainless steel safety chimney (300 mm diameter, 6000 mm length) Functional description: 1. filling the autoclave with wood 2. creating a pre-vacuum 3. filling with gas 4. heating Gjdpfx Ahev Si Szenoud 5. modifying 6. cooling 7. pressure equalization 8. creating a post-vacuum / drying 9. pressure equalization 10. emptying Certified EC Pressure Equipment Directive (PED) 97/23/EF Construction EN 13445 Sale on behalf of customer, from location near 5020 Salzburg (Austria), without dismantling, transportation and assembly Dismantling, loading and transportation by us optionally possible Subject to errors in the description and price To avoid possible misunderstandings, an on-site inspection by appointment is possible and recommended Sold as is Technical details, condition description, year of construction and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: “purchased as seen” Pictures and videos serve as examples and do not represent the actual scope of delivery Terms of payment: Prices excl. VAT, payment before collection or dispatch Terms of delivery: ex location

Condition: new, The new cylinder brush and sanding machine from Holzprofi Maker can be quickly and easily converted from a sanding machine to a brushing machine in just a few seconds. It is ideal for smaller workshops as it combines two machines in one. Advantages and Features: Gujdpowzzivjfx Ahnsd - Versatile options for surface finishing - Quick and easy changeover from sanding to brushing - Many different brushes available for a wide range of effects and processing possibilities - Infinitely variable feed rate and roller speed for perfect results - Workpiece width up to approx. 1100 mm - Precise adjustment of sanding height for consistent results Technical Data: Sanding width: 560 mm (1120 mm) Sanding height: 3 to 75 mm Roller diameter: Ø132 mm Table dimensions: 592x530 mm Extension table dimensions (2x): 582x245 mm Roller speed: 0 to 1800 rpm Feed speed: 0 to 7.5 m/min Extraction port diameter: 100 mm Main motor power: 1.5 kW Feed motor power: 120 W Voltage: 230 V Dimensions: 1010x1060x1190 mm Weight: 155 kg Optional Accessories: Texturing brush for even and structured surfaces Abrasive flap brush for finishing and surface preparation tasks Steel wire brush for a used-look finish and pronounced grain effect

Condition: good (used), Year of construction: 2014, functionality: fully functional, overall weight: 2,200 kg, KUKA KRC4 linear axis 1500/3T Gedsvzxg Tepfx Ahneud Article number: 8143983 Serial number: 143983 The KUKA KRC4 linear axis is a high-precision and robust motion unit that is ideal for industrial applications. It ensures precise control of motion sequences and plays a central role in automation processes and robotic systems within production. Its stable construction ensures consistently reliable performance, even in the most demanding applications.

Condition: ready for operation (used), Year of construction: 2009, functionality: fully functional, saw blade diameter: 460 mm, cutting range round steel at 90°: 150 mm, working height: 1,030 mm, MSK 471 NA automatic straight cut circular saw Gusdsubbw Ajpfx Ahned for HSS and carbide saw blades Cutting range round up to 150 mm, square up to 140 mm Suitable for almost all profile shapes and solid material Automatic cut-off sorting by means of cut-off gripper Machine tested at KALTENBACH, wear parts replaced

Year of construction: 2016, condition: ready for operation (used), Control Unit Gjdpfox H Uz Nsx Ahneud Brand HAAS Model Sigma 5 Main Drive Number of axis 2 This HAAS TR160 with Sigma 5 was manufactured in 2016. It features a 2-axis table and is equipped with a Sigma 5 servo motor, ensuring precise and efficient operation. Ideal for those looking to enhance their machining capabilities. Contact us for more information. Application Types Other Machine Tools

Condition: new, Year of construction: 2024, Working width: 600 mm Working height: 5 mm to 300 mm Guodpfx Ahsupy Spjned Minimum workpiece length: 250 mm Units: 2 1. Saw cutting unit Random System: Saw cut appearance 2. Brush: Tynex, diameter 210 mm Height adjustment: electric Height display: digital Feed speed: 4 - 14 m/min Motor power saw unit: 1.1 kW Motor power brush: 4 kW Motor power feed: 0.37 kW Machine length: 1400 mm Machine width: 1500 mm Machine height: 1600 mm Weight: 700 kg