Ultrasonic cleaning basin

ZN Beckeninnenmaß 2200/315/H280 mm

Condition: new, Fastech 3-Roll Round Bending Machine FRM 1050 x 90 Technical Specifications: Special equipment included in the price: hardened rolls motorized rear roll adjustment digital display Sheet metal width 1050 mm Sheet metal thickness 3.3 mm max. Sheet metal thickness for pre-bending 3.0 mm Roll length 1050 mm Roll diameter 90 mm Smallest bending diameter 130 mm Weight 475 kg Dimensions L-W-H 1750 x 800 x 1130 mm Motor: 1.1 KW Equipment: Top and bottom rolls, electrically driven Top roll can be pivoted out Taper bending device asymmetrical roll arrangement Podpfx Akshzq Dbsiorc self-braking main motor separate control and operating panel Safety cable Values apply to St-37 / 240 N/mm² CE marking

Condition: as good as new (ex-display), Year of construction: 2026, -Usable internal dimensions: D=900mm H=580mm (other sizes available upon request) -Spraying pressure: 3.2 Bar -Basket load: 200kg -Tank volume: 130L -Standard accessories: • Oil skimmer • Pumping device • Frame, lid, and housing made of stainless steel • Time-controlled electric steam extraction • Basket made of stainless steel • Filter made of stainless steel on the suction side of the pump • Heating elements made of stainless steel • Mechanical basket rotation with geared motor • Electrical system IP 65, control via PLC (DGT V4) • Automatic water supply • Safety limit switch monitors lid opening • Spray nozzles made of stainless steel Pjdpfx Akof A D Itjierc • Weekly timer for heating and oil separator • Operating hour counter

Year of construction: 2020, condition: new, Washers Ultrasonic Baths for washing, phosphatizing, chromating, degreasing, removing paint coatings materials Prodpjfzk Ewsfx Akioc In ROMER Ultrasonic Washers, stainless steel is used which provides protection against acids. Bathtubs have an additional insulation wall, so they do not lose temperature and heat up faster. Good quality materials ensure long life of the vibrating elements. Heating system The heaters used in the ROMER bathtubs are made of the highest quality materials and are made of high temperature resistant ceramic elements. The heating system used ensures great thermal efficiency, hot water automatically mixes with cold water, heating the entire bathtub. Ultrasonic transducers Ultrasonic elements used in ROMER washers are installed in immersion modules, which better reflect vibrations and are exchangeable. The ultrasound range is 20-40kHz depending on the washed element, lower frequencies are used for large elements of high strength, lower for jewelry, sensitive mechanical systems, etc. All transducers are connected by high temperature resistant cables.

Year of construction: 2024, condition: as good as new (ex-display), Metalclean - Metalclean-P-120 spray cleaning system in stainless steel 1-tank spray cleaning system with a rotating basket. Equipped with a pneumatic oil separator. Stainless steel pump with a spray pressure of 5 bar. Usable dimensions = D = 1,200 mm H = 700 mm Load capacity / batch = 300 kg Prodpfsir Anqjx Akioc Tank volume = 270 liters Operating voltage = 3 x 400 V/N/PE 50 Hz Fume extraction

Year of construction: 2026, condition: as good as new (ex-display), Spray Cleaning System - Parts Washing System - NEW SYSTEM / Pilot Plant Basket dimensions (octagonal): 1,287 mm Basket diagonal: 1,393 mm Useful height: 900 mm Max. loading weight: 600 kg Pedpfswitvqex Akisrc Tank volume: 500 liters, spray pressure: 5 bar, 400 l/min. Heatable up to 90°C System made entirely of stainless steel 1.4301 (AISI 304) and dip-pickled Including loading trolley in front of the system Included special equipment: - Steam extraction including condensate return - Automatic Water refill and level monitoring - Removable coarse filter in the return line to the wash tank - Removable basket surround - Preparation for retrofitting an oil separator - Weekly timer for heating - Electric spray pipe for optimized component cleaning - Inspection hatch in the tank area - Siemens S7 1200 control system with color touch panel, manufactured by Weintek Upon request, commissioning can be carried out by qualified personnel for an additional charge.

Condition: excellent (used), Year of construction: 2010, total height: 3,300 mm, total length: 5,600 mm, total width: 4,300 mm, table load: 2,000 kg, overall weight: 10,500 kg, Spindle SK 40 Speeds 8000 Rpm with 165 Nm Workload 2000 Kg ATC 56 Positions Hours spindle 10.304 Closed housing with automatic top door IKZ Coolant system LTA Air Cleaning Prjdpfx Akeyh U E Hsijc Length:5600mm Width:4300mm Height:3300mm Weight:10500kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: good (used), Direct from large Supermarket owned vegetable factory. Inline tray washer with dryer. High throughput system. Podpsu Ixt Dsfx Akisrc

Condition: good (used), Year of construction: 2017, travel distance X-axis: 1,600 mm, travel distance Y-axis: 820 mm, travel distance Z-axis: 820 mm, rapid traverse X-axis: 20,000 m/min, rapid traverse Y-axis: 20,000 m/min, rapid traverse Z-axis: 18,000 m/min, controller model: HARTROL PLUS 1 (MITSUBISHI), table width: 820 mm, table length: 1,750 mm, table load: 2,200 kg, number of slots in tool magazine: 40, Hartford HCMC-1682 Vertical Machining Center – Year 2017 Psdpfx Akszaapkeisrc The Hartford HCMC-1682 vertical machining center represents an ideal solution for medium and large-size mechanical machining operations that require high structural rigidity, reliability, and precision. Thanks to its robust construction and ISO 50 spindle, this machine is particularly suitable for roughing and finishing operations on steel, cast iron, and high-strength materials. Equipped with a Hartrol Plus 1 (Mitsubishi) CNC control, the machining center offers generous travels of 1,600 x 820 x 820 mm, allowing the machining of large-size components with a weight of up to 2,200 kg on the table. The two-range speed spindle, with a power of up to 18.5 kW and a maximum speed of 6,000 rpm, guarantees high chip removal performance and considerable torque at low speeds. The machine is equipped with a 40-position automatic tool magazine, through-spindle high-pressure coolant, chip conveyor, and a dedicated spindle cooler, making it ready for intensive and continuous production. Main technical features: Hartrol Plus 1 (Mitsubishi) CNC control X/Y/Z axis travels: 1,600 / 820 / 820 mm Table: 1,750 x 820 mm Table load capacity: 2,200 kg ISO 50 spindle Spindle speed: 6,000 rpm Spindle power: 15 / 18.5 kW Tool magazine: 40 positions Rapid traverse rates X/Y: 20 m/min Rapid traverse rate Z: 18 m/min Included accessories: Chip conveyor Coolant tank with pumps High-pressure coolant through spindle Spindle coolant cooler Manuals, electrical diagrams, and CE declaration

Condition: as good as new (ex-display), Year of construction: 2023, operating hours: 150 h, functionality: fully functional, total width: 2,920 mm, total length: 5,720 mm, total height: 3,360 mm, maximum load weight: 50 kg, heating capacity: 59 kW (80.22 HP), warranty duration: 6 months, input frequency: 50 Hz, year of last overhaul: 2026, 4-chamber ultrasonic cleaning system with automatic goods transport Maximum loading weight: 50 kg including basket Usable basket dimensions (internal): 426 x 375 x 470h mm Loading station with transport trolley 1. Ultrasonic cleaning with bottom and side sonication (25/45 kHz - switchable) 2. Ultrasonic rinsing with bottom sonication (25/45 kHz - switchable) 3. Ultrasonic rinsing with bottom sonication (25/45 kHz - switchable), including lift-out function 4. Hot air dryer Unloading station Predpfx Ajy H Uzvekisc - Tank 1 (ultrasonic cleaning) is also equipped with an overflow and a large separate oil separator. - Automatic cover on Tank 1 - Media filtration in all tanks (via cartridge filter) - Complete system enclosed and with exhaust extraction - Control system: Siemens S7-1500 incl. 12" HMI touch panel - Documentation available in German Electrical connected load: 59 kW The system can also be dismantled and re-installed at a new location by our specialist technicians for an additional charge, if required. Water treatment for Tank 4 (final rinse) can be supplied at extra cost. Test cleaning possible at any time, the system is powered up.

Condition: excellent (used), Year of construction: 2011, Table size: 1800 x 800 mm Tool holder DIN 69871: ISO 40 Travel ranges: X-axis: 1615 mm Y-axis: 815 mm Z-axis: 725 mm Table load: 2000 kg Spindle speed range: 0 - 10,000 rpm Feed rate: up to 10 m/min Rapid traverse: 24 m/min Footprint (W x D x H): approx. 5400 x 4550 x 3120 mm Drive power: 15 / 18.5 kW Weight: 10,000 kg Accessories / Special features: • CNC control system FAGOR 8055 i/PLUS MS • Internal coolant supply through the spindle, 20 bar • 24-position tool changer • Hinged chip conveyor • Coolant system • CE compliant Prodpfx Akeyy Npnsioc Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel / Germany